Rohm MCR25YRTD9R1 Thick film chip resistor Datasheet

Thick Film Chip Resistors
MCR Series < Automotive >
Features
1) Full line up from ultra small size (01005) to 2512 with jumper type.
2) High reliability metal glazed thick film.
3) ROHM resistors have obtained ISO9001/ISO/TS16949 certification.
4) "Automotive" product is AEC-Q200 compliant.
Size
Part No.
MCR004
(mm)
0402
Type Code
(inch)
Packing
Specification
Quantity / Reel
−
Paper tape
(2mm pitch)
15,000
RZP
−
Embossed tape
(1mm pitch)
40,000
YRT
YZP
MRT
MZP
GENERAL PURPOSE
AUTOMOTIVE
∗Corresponds to
AEC−Q200
YZP
01005
MCR006
0603
0201
MCR01
1005
0402
10,000
PZPI
(*For further information on datasheet,
please refer to AUTOMOTIVE datasheet.)
EZP
ERT
MCR03
1608
0603
MZP / PZPI
(*For further information on datasheet,
please refer to AUTOMOTIVE datasheet.)
MCR10
2012
0805
ERT
EZP
MCR18
3216
1206
ERT
EZP
MCR25
3225
1210
JZH
MCR50
5025
2010
JZH
MCR100
6432
2512
JZH
15,000
Paper tape
(2mm pitch)
Bulk case
50,000
Paper tape
(4mm pitch)
5,000
MZP : Paper tape
(2mm pitch)
PZPI : Bulk case
MZP : 10,000
PZPI : 25,000
Paper tape
(4mm pitch)
5,000
Embossed tape
(4mm pitch)
4,000
∗Please contact us for status of AEC-Q200 on "General purpose" products.
Part Number Description
M C R
0 0 6
Part No.
Size (mm [inch])
MCR
004 (0402 [01005])
006 (0603 [0201])
01 (1005 [0402])
03 (1608 [0603])
10 (2012 [0805])
18 (3216 [1206])
25 (3225 [1210])
50 (5025 [2010])
100 (6432 [2512])
(Micro chip resistors)
www.rohm.com
c 2012 ROHM Co., Ltd. All rights reserved.
○
Y R T
Type Code
J
1 0 0
Resistance Tolerance
Nominal Resistance
D ( ±0.5% )
F ( ±1% )
FX ( ±1% ) ∗Only MCR03EZP/MZP/PZPI
J ( ±5% ) (Including jumper type)
Resistance code, 3 or 4 digits.
000 denotes jumper type.
Resistance
tolerance
D,F
J
Resistance
code
:
:
4 digits
3 digits
Ex.)
1Ω = 1R0 ( ±5% )
9.1 Ω = 9R1 ( ±5% )
10 Ω = 10R0 ( ±0.5%,±1% )
100 ( ±5% )
2.2M Ω = 2204 ( ±1% )
225 ( ±5% )
1/6
2012.11 - Rev.D
MCR series < Automotive >
Data Sheet
Products List
Part No.
Type Code
Rated Power Limiting Element
(70°C)
Voltage
(W)
MCR006
YZP
0.05
(V)
25
Maximum
Overload
Voltage
(V)
−
Temperature Resistance
Coefficient Tolerance
(ppm / °C)
+600 / −200
±250
±250
±200
±100
Resistance Range
Series
Operating
Temperature
Range
(°C)
1.0Ω to 9.1Ω
10Ω to 10MΩ
10Ω to 10MΩ
10Ω to 910Ω
1kΩ to 1MΩ
E24
−55 to +125
(%)
J(±5%)
F(±1%)
D(±0.5%)
Jumper type : Rmax = 50m Ω / Imax. = 0.5A
MCR01
MCR03
MZP
PZPI
EZP
MZP
PZPI
0.063
0.1
50
50
0.125
MCR10
150
EZP
0.1
−
+500 / −250
±200
±100
±100
±50
J(±5%)
F(±1%)
D(±0.5%)
1.0Ω to 9.1Ω
10Ω to 10MΩ
10Ω to 2.2MΩ
10Ω to 91Ω
100Ω to 1MΩ
Jumper type : Rmax = 50m Ω / Imax. = 1A
1.0Ω to 9.1Ω
±400
J(±5%)
±200
10Ω to 10MΩ
±100
10Ω to 10MΩ
FX(±1%)
100
±100
10Ω to 91Ω
D(±0.5%)
±50
100Ω to 1MΩ
Jumper type : Rmax = 50m Ω / Imax. = 1A
±400
1.0Ω to 9.1Ω
J(±5%)
200
±200
10Ω to 10MΩ
±100
10Ω to 2.2MΩ
F(±1%)
±100
10Ω to 91Ω
300
D(±0.5%)
±50
100Ω to 1MΩ
E24
E24,E96
E24
E24
E24,E96
E24
E24,E96
Jumper type : Rmax = 50m Ω / Imax. = 2A
0.25
MCR18
200
EZP
400
0.125
±400
±200
±100
±100
±50
1.0Ω to 9.1Ω
10Ω to 10MΩ
10Ω to 2.2MΩ
10Ω to 91Ω
100Ω to 1MΩ
J(±5%)
F(±1%)
D(±0.5%)
−55 to +155
E24
E24,E96
Jumper type : Rmax = 50m Ω / Imax. = 2A
500±350
MCR25
JZH
0.25
200
400
±500
±200
±100
MCR50
MCR100
JZH
JZH
0.5
1
200
200
1.0Ω to 2.0Ω
2.2Ω to 5.1Ω
J(±5%)
E24
5.6Ω to 3.3MΩ
F(±1%)
10Ω to 1MΩ
Jumper type : Rmax = 50m Ω / Imax. = 2A
500±350
1.0Ω to 2.0Ω
±500
2.2Ω to 9.1Ω
J(±5%)
±200
10Ω to 330kΩ
400
±350
360kΩ to 560kΩ
±100
F(±1%)
10Ω to 180kΩ
Jumper type : Rmax = 50m Ω / Imax. = 3A
500±350
1.0Ω to 2.0Ω
±500
2.2Ω to 9.1Ω
J(±5%)
±350
10Ω to 22Ω
400
±200
24Ω to 100kΩ
±100
10Ω to 82kΩ
F(±1%)
E24,E96
E24
E24,E96
E24
−55 to +125
E24,E96
Jumper type : Rmax = 50m Ω / Imax. = 4A
∗Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product
before using or ordering it.
www.rohm.com
c 2012 ROHM Co., Ltd. All rights reserved.
○
2/6
2012.11 - Rev.D
MCR series < Automotive >
Data Sheet
Chip Resistor Dimensions and Markings
MCR004 / 006 / 01 / 03
L
103
MCR10 / 18 / 25 / 50 / 100
L
a
a
W
W
a
<Marking method>
There are three or four digits used for the calculation number
according to IEC code and “R”is used for the decimal point.
t
t
b
b
b
(Unit : mm)
Part No.
Type Code
(mm)
(inch)
L
W
t
a
b
Marking
existence
MCR006
YZP
0603
0201
0.6±0.03
0.3±0.03
0.23±0.03
0.1±0.05
0.15±0.05
No
MCR01
MZP
PZPI
1005
0402
1.0±0.05
0.5±0.05
0.35±0.05
0.2±0.1
+0.05
0.25 −0.1
No
MCR03
EZP
MZP
PZPI
1608
0603
1.6±0.1
0.8±0.1
0.45±0.1
0.3±0.2
0.3±0.2
Yes ∗
MCR10
EZP
2012
0805
2.0±0.1
1.25±0.1
0.55±0.1
0.4±0.2
0.4±0.2
Yes
MCR18
EZP
3216
1206
3.2±0.15
1.6±0.15
0.55±0.1
0.5±0.25
0.5±0.25
Yes
MCR25
JZH
3225
1210
3.2±0.15
2.5±0.15
0.55±0.15
0.5±0.25
0.5±0.25
Yes
MCR50
JZH
5025
2010
5.0±0.15
2.5±0.15
0.55±0.15
0.6±0.25
0.6±0.25
Yes
MCR100
JZH
6432
2512
6.3±0.15
3.2±0.15
0.55±0.15
0.6±0.25
0.6±0.25
Yes
Marking method of jumper type
Jumper type
MCR006 / 01 / 25 / 50 / 100
MCR03 / 10 / 18
Marking existence
No
Yes
Marking method of MCR03
For MCR03 series resistors, the printing process restricts the marking to three digits/characters.
Consequently, 1% tolerance resistors with values from the E24 series will be marked the same as
5% resistors with the same value, but 1% tolerance resistors with values from the E96 series will not be marked.
Examples:
MCR03EZPJ243
MCR03EZPFX2402
MCR03EZPFX2432
(5% tolerance, E24 / 24 k  )
(1% tolerance, E24 / 24 k  )
(1% tolerance, E96 / 24.3 k  )
Marking = 243
Marking = 243
No Marking
MCR18EZPJ243
MCR18EZPF2402
MCR18EZPF2432
(5% tolerance, E24 / 24 k  )
(1% tolerance, E24 / 24 k  )
(1% tolerance, E96 / 24.3 k  )
Marking = 243
Marking = 2402
Marking = 2432
(Unit : mm)
Land pattern Example
Dimensions
Part No.
MCR006
B
MCR01
D
MCR03
Land
C
A
www.rohm.com
c 2012 ROHM Co., Ltd. All rights reserved.
○
3/6
Type Code
A
B
C
D
YZP
0.3
0.84
0.3
0.27
0.5
1.3
0.5
0.4
1.0
2.0
0.8
0.5
MZP
PZPI
EZP
MZP
PZPI
MCR10
EZP
1.2
2.6
1.15
0.7
MCR18
EZP
2.2
4.0
1.5
0.9
MCR25
JZH
2.2
4.0
2.3
0.9
MCR50
JZH
3.8
6.0
2.3
1.1
MCR100
JZH
5.1
8.1
3.0
1.5
2012.11 - Rev.D
MCR series < Automotive >
Data Sheet
Derating Curve
When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below.
MCR006 / 100
PERCENT RATED POWER (%)
PERCENT RATED POWER (%)
80
60
40
20
0
MCR01 / 03 / 10 / 18 / 25 / 50
100
100
−55
0
70
100
80
60
40
20
0
125
−55
0
AMBIENT TEMPERATURE (°C)
70
100
155
AMBIENT TEMPERATURE (°C)
Characteristics
Guaranteed Value
Resistor Type
Jumper Type
Test Items
Test Conditions
Resistance
See "Products List"
20°C
Variation of resistance
with temperature
See "Products List"
Measurement : +20 / −55 / +20 / +125°C
± (2.0%+0.1Ω)
Overload
Rated voltage (current) ×2.5, 2s.
Maximum overload voltage
Max. 50mΩ
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
Solderability
± (1.0%+0.05Ω)
Resistance to
soldering heat
Max. 50mΩ
No remarkable abnormality on the appearance.
Rosin·Ethanol : 25% (Weight)
Soldering condition : 235±5°C
Duration of immersion : 2.0±0.5s
Soldering condition : 260±5°C
Duration of immersion : 10±1s
Rapid change of
temperature
± (1.0%+0.05Ω)
Max. 50mΩ
Test temp.
−55°C to +125°C 100cycle (MCR006 / 01 / 03)
−55°C to +125°C 5cycle (MCR10 / 18 / 25 / 50 / 100)
Damp heat, steady state
± (3.0%+0.1Ω)
Max. 100mΩ
40°C, 93%RH (Relative Humidity)
Test time : 1,000h to 1,048h
Endurance at 70°C
± (3.0%+0.1Ω)
Max. 100mΩ
70°C
Rated voltage (current)
1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h
Endurance
± (3.0%+0.1Ω)
Max. 100mΩ
125°C (MCR006 / 25 / 50 / 100)
155°C (MCR01 / 03 / 10 / 18)
Test time : 1,000h to 1,048h
Resistance to solvent
± (1.0%+0.05Ω)
Max. 50mΩ
23±5°C, Immersion cleaning, 5±0.5min
Solvent : 2−propanol
± (1.0%+0.05Ω)
Max. 50mΩ
Bend strength of
the end face plating
−
Without mechanical damage such as breaks.
Compliance Standard(s) : IEC60115−8
JISC 5201−8
Chip weight (typical value)
Parameter
Unit
MCR006
YZP
Weight
mg/pc
0.157
MCR01
MCR03
MZP / PZPI EZP / MZP / PZPI
0.70
www.rohm.com
c 2012 ROHM Co., Ltd. All rights reserved.
○
2.12
MCR10
EZP
MCR18
EZP
MCR25
JZH
MCR50
JZH
MCR100
JZH
5.03
9.46
16.5
25.8
42.0
4/6
2012.11 - Rev.D
MCR series < Automotive >
Data Sheet
Tape Dimensions

Paper Tape
(Unit : mm)
P0
P2
P1
Part No.
Type Code
W
F
E
A0
B0
MCR006
YZP
8.0±0.2
3.5±0.05
1.75±0.1
0.38±0.03
0.68±0.03
MCR01
MZP
8.0±0.3
3.5±0.05
1.75±0.1
0.7±0.1
1.2±0.1
MCR03
EZP
8.0±0.3
3.5±0.05
1.75±0.1
1.1±0.1
1.9±0.1
MCR10
EZP
8.0±0.3
3.5±0.05
1.75±0.1
1.65
+0.2
−0.1
2.4
+0.2
−0.1
MCR18
EZP
8.0±0.3
3.5±0.05
1.75±0.1
1.95
+0.1
−0.05
3.5
+0.15
−0.05
Part No.
Type Code
D0
P0
P1
P2
T2
MCR006
YZP
φ1.5
+0.1
0
4.0±0.1
2.0±0.05
2.0±0.05
Max 0.5
MCR01
MZP
φ1.5
+0.1
0
4.0±0.1
2.0±0.05
2.0±0.05
Max 1.1
MCR03
EZP
φ1.5
+0.1
0
4.0±0.1
4.0±0.1
2.0±0.05
Max 1.1
MCR10
EZP
φ1.5
+0.1
0
4.0±0.1
4.0±0.1
2.0±0.05
Max 1.1
MCR18
EZP
φ1.5
+0.1
0
4.0±0.1
4.0±0.1
2.0±0.05
Max 1.1
Part No.
Type Code
W
F
E
A0
B0
8.0±0.3
3.5±0.05
1.75±0.1
1.1±0.1
1.9±0.1
D0
P0
P1
P2
T2
4.0±0.1
2.0±0.5
2.0±0.05
Max 1.1
φD0
E
F
W
B0
A0
Top tape
Base paper
(Bottom tape)
Components
Cavity
T2

Paper Tape (Narrow pitch taping)
(Unit : mm)
P0
φD
P2
0
E
F
A0
W
MCR03
MZP
B0
φ1.5
+0.1
0
P1
Top tape
Base paper
(Bottom tape)
Components
Cavity
T2

Embossed Tape
(Unit : mm)
Part No.
Type Code
W
F
E
A0
B0
MCR25
JZH
8.0±0.3
3.5±0.05
1.75±0.1
3.0±0.1
3.5±0.1
MCR50
JZH
12±0.3
5.5±0.05
1.75±0.1
3.4±0.2
5.6±0.2
MCR100
JZH
12±0.3
5.5±0.05
1.75±0.1
3.5±0.2
6.7±0.2
Part No.
Type Code
D0
P0
P1
P2
T2
MCR25
JZH
φ1.5
+0.1
0
4.0±0.1
4.0±0.1
2.0±0.05
Max 1.1
MCR50
JZH
φ1.5
+0.1
0
4.0±0.1
4.0±0.1
2.0±0.05
Max 1.1
MCR100
JZH
φ1.5
+0.1
0
4.0±0.1
4.0±0.1
2.0±0.05
Max 1.1
B0
W
F
φD
0
P2
E
P0
A0
P1
T2
www.rohm.com
c 2012 ROHM Co., Ltd. All rights reserved.
○
5/6
2012.11 - Rev.D
MCR series < Automotive >
Data Sheet
02
04
06
08
06
D
04
B
02
A
08
Reel Dimensions
C
Label
ACCORDING EIAJ ET-7200B
(Unit : mm)
Part No.
Type Code
MCR006
YZP
MCR01
MZP
MCR03
EZP
MZP
MCR10
EZP
MCR18
EZP
MCR25
JZH
MCR50
JZH
MCR100
JZH
A
B
0
φ180
−1.5
+1.0
φ60
0
C
9
D
+1.0
0
13
φ13±0.2
+1.0
0
Bulk case Dimensions


MCR01PZPI
MCR03PZPI
Slider
Shutter
12.0±0.1
36
0
−0.2
110±0.7
EIAJ ET-7200B compliant
www.rohm.com
c 2012 ROHM Co., Ltd. All rights reserved.
○
(Unit : mm)
6/6
2012.11 - Rev.D
Notice
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any
of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
R1120A
Similar pages