P-DUKE DOS30-05T Point of load dc-dc converter Datasheet

DOS(H)30 SERIES
POINT OF LOAD
DC-DC CONVERTER
FEATURES
APPLICATIONS
Wireless Network
Telecom/Datacom
Industry Control System
Distributed Power Architectures
Semiconductor Equipment
Microprocessor Power Applications
T E C H N I C A L S P E C I F I C AT I O N
• OUTPUT CURRENT UP TO 30A
• SMALL SIZE AND LOW PROFILE :
DOS30-05T:1.30 X 0.53 X 0.37 INCH , DOH30-05T:2.00 X 0.50 X 0.37 INCH
DOS30-12T:1.30 X 0.53 X 0.31 INCH , DOH30-12T:2.00 X 0.50 X 0.31 INCH
• HIGH EFFICIENCY UP TO 93%@5VIN, 3.3VOUT, FULL LOAD
• DOS(H)30-05T : 4.5VDC TO 5.5VDC INPUT, 0.8VDC TO 3.63VDC OUTPUT
DOS30-12T : 6.0VDC TO 14.0VDC INPUT, 0.8VDC TO 3.63VDC OUTPUT
DOH30-12T : 6.0VDC TO 14.0VDC INPUT, 0.8VDC TO 5.5VDC OUTPUT
OUTPUT VOLTAGE PROGRAMMABLE VIA EXTERNAL RESISTOR
• SMD PACKAGE QUALIFIED FOR LEADFREE REFLOW SOLDER
PROCESS ACCORDING IPC J-STD-020D
• FIXED SWITCHING FREQUENCY (300kHZ)
• MONOTONIC START-UP INTO PRE-BIASED OUTPUT
• OUTPUT VOLTAGE SEQUENCING
• PARALLEL OPERATION WITH ACTIVE CURRENT SHARING
• SAFETY MEETS UL60950-1, EN60950-1, & IEC60950-1
• CE MARK MEETS 2006/95/EC, 2011/95/EC and 2004/108/EC
• COMPLIANT TO RoHS II & REACH
OPTIONS
POSITIVE LOGIC REMOTE ON/OFF, CURRENT SHARE,
EXTRA GND PIN, LONG PINS
DESCRIPTION
□□
All specifications are typical at nominal input, 3.3Vo, full load and 25ºC otherwise
OUTPUT SPECIFICATIONS
DOS30-05T
30A max.
DOH30-05T
30A max.
DOS30-12T 0.8≦Vout≦2.75VDC
30A max.
Output current
2.75<Vout≦3.63VDC
20A max.
DOH30-12T 0.8≦Vout≦2.75VDC
30A max.
2.75<Vout≦5.5VDC
25A max.
Voltage accuracy
± 1.5%Vout(set)
Minimum load
0%
Vin=Vin(min.) to Vin(max.)
Line regulation
± 0.1%Vout(set)
at Full Load
Load regulation
No Load to Full Load
± 0.4%Vout(set)
Ripple and noise (Note 2) 20MHz bandwidth
75mVp-p
Temperature coefficient
±0.5%
ΔIout/t = 5A/µs ,Vin(nom)
Peak deviation
350mV
Dynamic load
Setting time
Load change step
response
(50%
to
100%
or
(Vout<10%peak
25µs
(Note 2)
100% to 50% of Iout(max.)) deviation)
ΔIout/t = 5A/µs ,Vin(nom)
Peak deviation
250mV
Dynamic load
Load change step
Setting time
response
(50% to 100% or
(Vout<10%peak
40µs
(Note 3)
100% to 50% of Iout(max.)) deviation)
Output current limit
150%
Output short-circuit current
Hiccup, Automatics recovery
ESR≧1mΩ
2000µF,max.
External load capacitance
ESR≧10mΩ
10000µF,max.
Vin=Vin(min.) to
Output voltage overshoot-startup
3%Vout(set), max.
Vin(max.) and F.L.
DOS30-05T
0.8VDC ~ 3.63VDC
Voltage adjustability (see fig.1) DOH30-05T
0.8VDC ~ 3.63VDC
(Note 4)
0.8VDC ~ 3.63VDC
DOS30-12T
0.8VDC ~ 5.5VDC
DOH30-12T
GENERAL SPECIFICATIONS
□□
DOS30T (SMD type), DOH30
T (SIP type) are non-isolated DC/DC converters
that can deliver up to 30A of output current with full load efficiency of 93% at 5.0V input
and 3.3V output.
INPUT SPECIFICATIONS
DOS30-05T
DOH30-05T
Vin(nom) =5VDC
DOS30-12T
DOH30-12T
Vin(nom) =12VDC
Input voltage range
4.5 ~ 5.5VDC
Vin,min.=Vout(set)+1.5VDC
6.0 ~ 14.0VDC
Vin,min.=Vout(set)+2.4VDC
Input filter (Note 5)
Input under-voltage
lockout
Input reflected ripple
current
C filter
Start-up voltage
Shutdown voltage
4.4VDC
4.3VDC
5~20MHz, 1uH source impedance
100mAp-p
ENVIRONMENTAL SPECIFICATIONS
Operating ambient temperature
Storage temperature range
-40ºC ~ +85ºC(with derating)
-55ºC ~ +125ºC
Thermal shock
MIL-STD-810F
Vibration
MIL-STD-810F
Relative humidity(non-condensing)
5% to 95% RH
Lead-free reflow solder process
Moisture sensitivity level(MSL)
Over temperature protection
IPC J-STD-020D
IPC J-STD-033B
Level 2a
125ºC
FEATURE SPECIFICATIONS
Sequencing delay time (Note 6)
10ms, min.
Tracking accuracy
∣VSEQ -Vout∣
Power-up (2V/ms)
100mV
Vin(min) to Vin(max), Iout(min.)
Power-down (1V/ms) to Iout(max.), VSEQ < Vout.
200mV
Active load share (option)
Accuracy
10% Iout
(Note 7)
Number of units in parallel
5pcs,max.
Remote ON/OFF (Note 8)
Negative logic(standard)ON = Open or -0.3V < Vr < 1.2V
IIN=200µA,max.
OFF = 3.0V < Vr < Vin(max.)
IIN=3.3mA,max.
Positive logic(option)
ON = Open or 3.0V < Vr < Vin(max.) IIN=200µA,max.
OFF= -0.3V < Vr < 1.2V
IIN=3.3mA,max.
Remote sense range
0.5V, max.
Efficiency
See table
Isolation voltage
None
Switching frequency
300kHz±13%
Safety meets
IEC60950-1, UL60950-1, & EN60950-1
DOS30-05T
1.30X0.53X0.37 Inch (33.0X13.5X9.4 mm)
1.30X0.53X0.31 Inch (33.0X13.5X7.8 mm)
DOS30-12T
Dimensions
Rise time Time for Vout to rise from 10% to 90%of Vout(set) 10ms, max.
DOH30-05T
2.00X0.50X0.37 Inch (50.8X12.7X9.4 mm)
Case 1 (Note 9)
2.5ms
2.00X0.50X0.31 Inch (50.8X12.7X7.8 mm) Turn-on delay time
DOH30-12T
Case 2 (Note 10)
2.5ms
6.0g(0.21oz)
SMD
Weight
7.0g(0.25oz)
SIP
MIL-HDBK-217F
1.258 x 106 hrs
MTBF (Note 1)
Page 1 of 3
www.pduke.com
2014/6/20
DOS(H)30 SERIES
POINT OF LOAD
DC-DC CONVERTER
Efficiency
No Load Current
Vin(nom),3.3VDC,
Min. Load Max. Load Vin(nom),3.3VDC
Full Load
Output Current
Model Name
Package
DOS30-05T
SMD
DOH30-05T
SIP
DOS30-12T
SMD
DOH30-12T
SIP
Input Voltage
Output Voltage
4.5 ~ 5.5VDC
Vin,min.=Vout(set)+1.5V
0.8 ~ 3.63VDC
0A
30A
180mA
93%
0.8 ~ 3.63VDC
0A
30A
180mA
93%
200mA
92%
200mA
92%
0.8 ≦Vout≦ 2.75VDC
6.0 ~ 14.0VDC
2.75 <Vout≦ 3.63VDC
Vin,min.=Vout(set)+2.4V 0.8 ≦Vout≦ 2.75VDC
2.75 <Vout≦ 5.5VDC
30A
20A
30A
25A
0A
0A
Note
1. MIL-HDBK-217F @Tc=70 ºC, Full load.
2. External with Cout = 1µF ceramic//10µF tantalum capacitors.
3. External with Cout = 2×150µF polymer capacitors.
4. Output voltage programmable from 0.8V to 5.0V by connecting a single resistor (shown as Rtrim in Table 1)
between the TRIM and GND pins of the module. To calculate the value of the resistor Rtrim for a particular
output voltage Vout, use the following equation:
5.
 1200

- 100 Ω
Rtrim = 
Vout - 0.80

To make sure the module is stable, input external capacitors is necessary that minimize input ripple voltage of
the module.
Delay from Vin,min. to application of voltage on SEQ pin.
Selecting current share function that the regulations may not meet listed specification.
The On/Off signal is referenced to ground. The standard remote On/Off logic of the device is negative logic.
Adding a device code suffix “-P” is option for positive logic of remote On/Off.
9. Case 1 :On/Off input is set to logic low (module on) and then input power is applied (delay from instant at which Vin=Vin(min.)
until Vout=10% of Vout(set))
10. Case 2 :Input power is applied for at least one second and then the On/Off input is set to logic low (delay form instant at which
Von/off=0.3V until Vout=10% of Vout(set))
6.
7.
8.
CAUTION: This power module is not internally fused. An input line fuse must always be used.
Figure 1
DOS30-05T, Vout=3.3V
Page 2 of 3
Table 1.
Derating Curve
www.pduke.com
Trim Table
Vout(set) (V)
Rtrim (Ω)
0.8
Open
1.2
2900
1.5
1614
1.8
1100
2.5
605
3.3
380
5.0
185
Table 2. Device Options
Option
Suffix
Remote On/Off
-P
Positive Logic
Current Share
-S
Extra GND pin
2 extra GND pins
-E
only for SMD TYPE
Long Pins
-L
5.08mm±0.25mm
only for SIP TYPE
2014/6/20
DOS(H)30 SERIES
MECHANICAL DRAWING
POINT OF LOAD
:
DC-DC CONVERTER
SIP TYPE
PIN CONNECTION
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
DEFINE
+OUTPUT
+OUTPUT
+SENSE
+OUTPUT
GND
GND
SHARE(option)
GND
+ INPUT
+ INPUT
SEQ
TRIM
CTRL
SMD TYPE
PIN CONNECTION
PIN
1
2
3
4
5
6
7
8
9
10
DEFINE
CTRL
GND(option)
SHARE(option)
+SENSE
TRIM
+OUTPUT
GND
SEQ
GND(option)
+ INPUT
1. All dimensions in Inch (mm)
Tolerance: X.XX±0.02 (X.X±0.5)
X.XXX±0.01 (X.XX±0.25)
2. Pin pitch tolerance ±0.01 (0.25)
3. Pin dimension tolerance ±0.004 (0.1)
Page 3 of 3
www.pduke.com
2014/6/20
Similar pages