HSMS-2700, 2702, 270B, 270C, 270P High Performance Schottky Diode for Transient Suppression Data Sheet Description Features The HSMS-2700 series of Schottky diodes, commonly referred to as clipping /clamping diodes, are optimal for circuit and waveshape preservation applications with high speed switching. Ultra-low series resistance, R S, makes them ideal for protecting sensitive circuit elements against higher current transients carried on data lines. With picosecond switching, the HSMS-270x can respond to noise spikes with rise times as fast as 1 ns. Low capacitance minimizes waveshape loss that causes signal degradation. • Ultra-low Series Resistance for Higher Current Handling • Picosecond Switching • Low Capacitance • Lead-free Applications RF and computer designs that require circuit protection, high-speed switching, and voltage clamping. HSMS-270x DC Electrical Specifications, TA = +25°C [1] Part Number HSMS- Package Marking Code [2] Lead Code Configuration -2700 J0 0 Single Package Maximum Forward Voltage VF (mV) Minimum Breakdown Typical Voltage Capacitance VBR (V) C T (pF) Typical Series Resistance R S (Ω) Maximum Eff. Carrier Lifetime τ (ps) 550 [3] 15[4] 0.65 100[6] SOT-23 -270B B SOT-323 (3-lead SC-70) -2702 2 SOT-23 -270C J2 C Series SOT-323 (3-lead SC-70) -270P JP P Bridge Quad SOT-363 (6-lead SC-70) 6.7[5] Notes: 1. TA = +25°C, where TA is defined to be the temperature at the package pins where contact is made to the circuit board. 2. Package marking code is laser marked. 3. I F = 100 mA; 100% tested 4. IR = 100 μA; 100% tested 5. VF = 0; f =1 MHz 6. Measured with Karkauer method at 20 mA; guaranteed by design. Package Lead Code Identification (Top View) SINGLE 3 1 0, B SERIES 3 2 1 2, C BRIDGE QUAD 6 5 4 2 1 2 3 Absolute Maximum Ratings, TA= 25ºC Absolute Maximum [1] Symbol Parameter Unit HSMS-2700/-2702 HSMS-270B/270C/270P IF DC Forward Current mA 350 750 IF-peak Peak Surge Current (1μs pulse) A 1.0 1.0 PT Total Power Dissipation mW 250 825 PINV Peak Inverse Voltage V 15 15 TJ Junction Temperature °C 150 150 TSTG Storage Temperature °C -65 to 150 -65 to 150 θJC Thermal Resistance, junction to lead °C/W 500 150 Note: 1. Operation in excess of any one of these conditions may result in permanent damage to the device. Linear and Non-linear SPICE Model 0.08 pF 2 nH RS SPICE model 2 SPICE Parameters Parameter Unit Value BV V 25 CJO pF 6.7 EG eV 0.55 IBV A 10E-4 IS A 1.4E-7 N 1.04 RS Ω 0.65 PB V 0.6 PT 2 M 0.5 Typical Performance 300 10 1 0.1 0.01 0 0.1 0.2 0.3 0.4 10 1 0.1 TA = +75 C TA = +25 C TA = –25 C TA = +75 C TA = +25 C TA = –25 C 0.01 0.5 TJ – JUNCTION TEMPERATURE ( C) 100 I F – FORWARD CURRENT (mA) I F – FORWARD CURRENT (mA) 160 Max. safe junction temp. 500 100 0.6 0 VF – FORWARD VOLTAGE (V) 0.1 0.2 0.3 0.4 0.5 0.6 100 80 60 40 20 0 0.7 0.8 VF – FORWARD VOLTAGE (V) Figure 1. Forward Current vs. Forward Voltage at Temperature for HSMS-2700 and HSMS-2702. 140 TA = +75 C TA = +25 C 120 TA = –25 C 0 50 100 150 200 250 300 Figure 2. Forward Current vs. Forward Voltage at Temperature for HSMS-270B and HSMS-270C. Figure 3. Junction Temperature vs. Forward Current as a Function of Heat Sink Temperature for the HSMS-2700 and HSMS-2702. Note: Data is calculated from SPICE parameters. 7 140 TA = +75 C TA = +25 C 120 T = –25 C A 6 CT – TOTAL CAPACITANCE (pF) TJ – JUNCTION TEMPERATURE ( C) 160 Max. safe junction temp. 100 80 60 40 0 4 3 1 0 150 300 450 600 750 IF – FORWARD CURRENT (mA) Figure 4. Junction Temperature vs. Current as a Function of Heat Sink Temperature for HSMS-270B and HSMS-270C. Note: Data is calculated from SPICE parameters. 3 5 2 20 0 5 10 15 VF – REVERSE VOLTAGE (V) Figure 5. Total Capacitance vs. Reverse Voltage. 350 IF – FORWARD CURRENT (mA) 20 Package Dimensions Device Orientation Outline SOT-23 For Outlines SOT-23/323 REEL e2 e1 CARRIER TAPE E E1 XXX USER FEED DIRECTION e COVER TAPE L B TOP VIEW C END VIE W 4 mm D DIMENSIONS (mm) SYMBOL A A1 B C D E1 e e1 e2 E L A A1 Notes: XXX-package marking Drawings are not to scale MAX. 1.20 0.100 0.54 0.20 3.13 1.50 1.02 2.04 0.60 2.70 0.69 MIN. 0.79 0.000 0.30 0.08 2.73 1.15 0.89 1.78 0.45 2.10 0.45 8 mm ABC ABC ABC ABC Note: "AB" represents package marking code. "C" represents date code. Recommended PCB Pad Layout Tape Dimensions and Product Orientation For Avago’s SOT-23 Products For Outline SOT-23 P P2 D E P0 0.039 1 0.039 1 F 0.079 2.0 W D1 t1 Ko 9° MAX 13.5° MAX 8° MAX B0 A0 DESCRIPTION 0.035 0.9 SYMBOL SIZE (mm) SIZE (INCHES) CAVITY LENGTH WIDTH DEPTH PITCH BOTTOM HOLE DIAMETER A0 B0 K0 P D1 3.15 ± 0.10 2.77 ± 0.10 1.22 ± 0.10 4.00 ± 0.10 1.00 + 0.05 0.124 ± 0.004 0.109 ± 0.004 0.048 ± 0.004 0.157 ± 0.004 0.039 ± 0.002 PERFORATION DIAMETER PITCH POSITION D P0 E 1.50 + 0.10 4.00 ± 0.10 1.75 ± 0.10 0.059 + 0.004 0.157 ± 0.004 0.069 ± 0.004 CARRIER TAPE WIDTH THICKNESS W t1 8.00 +0.30 –0.10 0.229 ± 0.013 0.315 +0.012 –0.004 0.009 ± 0.0005 DISTANCE BETWEEN CENTERLINE CAVITY TO PERFORATION (WIDTH DIRECTION) F 3.50 ± 0.05 0.138 ± 0.002 CAVITY TO PERFORATION (LENGTH DIRECTION) P2 2.00 ± 0.05 0.079 ± 0.002 4 0.031 0.8 Dimensions in inches mm Package Dimensions Recommended PCB Pad Layout For Avago’s SC70 3L/SOT-323 Products Outline SOT-323 (SC-70 3 Lead) e1 0.026 E E1 XXX 0.079 e L B 0.039 C D 0.022 DIMENSIONS (mm) A A1 Notes: XXX-package marking Drawings are not to scale SYMBOL A A1 B C D E1 e e1 E L MIN. MAX. 0.80 1.00 0.00 0.10 0.15 0.40 0.08 0.25 1.80 2.25 1.10 1.40 0.65 typical 1.30 typical 1.80 2.40 0.26 0.46 Dimensions in inches Outline SOT-363 (SC-70 6 Lead) DIMENSIONS (mm) HE SYMBOL E D HE A A2 A1 e b c L E e D A1 A2 b 5 MIN. MAX. 1.15 1.35 1.80 2.25 1.80 2.40 0.80 1.10 0.80 1.00 0.00 0.10 0.650 BCS 0.15 0.30 0.08 0.25 0.10 0.46 c A L Tape Dimensions and Product Orientation For Outline SOT-323/363 (SC-70 3 and 6 Lead) P P2 D P0 E F W C D1 t1 (CARRIER TAPE THICKNESS) K0 8° MAX. A0 DESCRIPTION 6 Tt (COVER TAPE THICKNESS) 8° MAX. B0 SYMBOL SIZE (mm) SIZE (INCHES) CAVITY LENGTH WIDTH DEPTH PITCH BOTTOM HOLE DIAMETER A0 B0 K0 P D1 2.40 ± 0.10 2.40 ± 0.10 1.20 ± 0.10 4.00 ± 0.10 1.00 + 0.25 0.094 ± 0.004 0.094 ± 0.004 0.047 ± 0.004 0.157 ± 0.004 0.039 + 0.010 PERFORATION DIAMETER PITCH POSITION D P0 E 1.55 ± 0.05 4.00 ± 0.10 1.75 ± 0.10 0.061 ± 0.002 0.157 ± 0.004 0.069 ± 0.004 CARRIER TAPE WIDTH THICKNESS W t1 8.00 ± 0.30 0.254 ± 0.02 0.315 ± 0.012 0.0100 ± 0.0008 COVER TAPE WIDTH TAPE THICKNESS C Tt 5.4 ± 0.10 0.062 ± 0.001 0.205 ± 0.004 0.0025 ± 0.00004 DISTANCE CAVITY TO PERFORATION (WIDTH DIRECTION) F 3.50 ± 0.05 0.138 ± 0.002 CAVITY TO PERFORATION (LENGTH DIRECTION) P2 2.00 ± 0.05 0.079 ± 0.002 Applications Information Schottky Diode Fundamentals The HSMS-270x series of clipping/clamping diodes are Schottky devices. A Schottky device is a rectifying, metal-semiconductor contact formed between a metal and an n-doped or a p-doped semiconductor. When a metal-semiconductor junction is formed, free electrons flow across the junction from the semiconductor and fill the free-energy states in the metal. This flow of electrons creates a depletion or potential across the junction. The difference in energy levels between semiconductor and metal is called a Schottky barrier. P-doped, Schottky-barrier diodes excel at applications requiring ultra low turn-on voltage (such as zero-biased RF detectors). But their very low, breakdown-voltage and high series-resistance make them unsuitable for the clipping and clamping applications involving high forward currents and high reverse voltages. Therefore, this discussion will focus entirely on n-doped Schottky diodes. Under a forward bias (metal connected to positive in an n-doped Schottky), or forward voltage, VF, there are many electrons with enough thermal energy to cross the barrier potential into the metal. Once the applied bias exceeds the built-in potential of the junction, the forward current, IF, will increase rapidly as VF increases. When the Schottky diode is reverse biased, the potential barrier for electrons becomes large; hence, there is a small probability that an electron will have sufficient thermal energy to cross the junction. The reverse leakage current will be in the nanoampere to microampere range, depending upon the diode type, the reverse voltage, and the temperature. In contrast to a conventional p-n junction, current in the Schottky diode is carried only by majority carriers (electrons). Because no minority-carrier (hole) charge storage effects are present, Schottky diodes have carrier lifetimes of less than 100 ps. This extremely fast switching time makes the Schottky diode an ideal rectifier at frequencies of 50 GHz and higher. Another significant difference between Schottky and p-n diodes is the forward voltage drop. Schottky diodes have a threshold of typically 0.3 V in comparison to that of 0.6 V in p-n junction diodes. See Figure 6. Through the careful manipulation of the diameter of the Schottky contact and the choice of metal deposited on the n-doped silicon, the important characteristics of the diode (junction capacitance, C J; parasitic series resistance, RS; breakdown voltage, VBR; and forward voltage, VF,) can be optimized for specific applications. The HSMS270x series and HBAT-540x series of diodes are a case in point. Both diodes have similar barrier heights; and this is indicated by corresponding values of saturation current, IS. Yet, different contact diameters and epitaxial-layer thickness result in very different values of C J and RS. This is seen by comparing their SPICE parameters in Table 1. Table 1. HSMS-270x and HBAT-540x SPICE Parameters. Parameter HSMS- 270x BV 25 V 40 V CJ0 6.7 pF 3.0 pF EG 0.55 eV 0.55 eV IBV 10E-4 A 10E-4 A IS 1.4E-7 A 1.0E-7 A N 1.04 1.0 RS 0.65 Ω 2.4 Ω PB 0.6 V 0.6 V PT 2 2 M 0.5 0.5 At low values of IF ≤ 1 mA, the forward voltages of the two diodes are nearly identical. However, as current rises above 10 mA, the lower series resistance of the HSMS270x allows for a much lower forward voltage. This gives the HSMS-270x a much higher current handling capability. The trade-off is a higher value of junction capacitance. The forward voltage and current plots illustrate the differences in these two Schottky diodes, as shown in Figure 7. 300 HSMS-270x N METAL N CAPACITANCE CURRENT CAPACITANCE CURRENT 0.6 V – Figure 6. + 0.3V – + BIAS VOLTAGE BIAS VOLTAGE PN JUNCTION SCHOTTKY JUNCTION I F – FORWARD CURRENT (mA) 100 P HBAT- 540x HBAT-540x 10 1 .1 .01 0 0.1 0.2 0.3 0.4 0.5 0.6 VF – FORWARD VOLTAGE (V) Figure 7. Forward Current vs. Forward Voltage at 25°C. 7 Because the automatic, pick-and-place equipment used to assemble these products selects dice from adjacent sites on the wafer, the two diodes which go into the HSMS-2702 or HSMS-270C (series pair) are closely matched —without the added expense of testing and binning. Current Handling in Clipping/Clamping Circuits The purpose of a clipping/clamping diode is to handle high currents, protecting delicate circuits downstream of the diode. Current handling capacity is determined by two sets of characteristics, those of the chip or device itself and those of the package into which it is mounted. tained at a low limit even at high values of current. Maximum reliability is obtained in a Schottky diode when the steady state junction temperature is maintained at or below 150°C, although brief excursions to higher junction temperatures can be tolerated with no significant impact upon mean-time-to-failure, MTTF. In order to compute the junction temperature, Equations (1) and (3) below must be simultaneously solved. 11600 (V F – I F R S ) IF = IS noisy data-spikes current limiting I S = I0 Vs e nTJ –1 2 1 1 T J n –4060 T J – 298 e 298 TJ = V F I F JC + TA long cross-site cable (1) (2) (3) where: pull-down (or pull-up) 0V voltage limited to Vs + Vd 0V – Vd I F = forward current IS = saturation current Figure 8. Two Schottky Diodes Are Used for Clipping/Clamping in a Circuit. VF = forward voltage Consider the circuit shown in Figure 8, in which two Schottky diodes are used to protect a circuit from noise spikes on a stream of digital data. The ability of the diodes to limit the voltage spikes is related to their ability to sink the associated current spikes. The importance of current handling capacity is shown in Figure 9, where the forward voltage generated by a forward current is compared in two diodes. RS = series resistance VF – FORWARD VOLTAGE (V) 6 IO = saturation current at 25°C n = diode ideality factor θ JC = thermal resistance from junction to case (diode lead) = θpackage + θchip T A = ambient (diode lead) temperature 5 Equation (1) describes the forward V-I curve of a Schottky diode. Equation (2) provides the value for the diode’s saturation current, which value is plugged into (1). Equation (3) gives the value of junction temperature as a function of power dissipated in the diode and ambient (lead) temperature. 4 Rs = 7.7 3 2 Rs = 1.0 1 0 0 0.1 0.2 0.3 0.4 0.5 IF – FORWARD CURRENT (mA) Figure 9. Comparison of Two Diodes. The first is a conventional Schottky diode of the type generally used in RF circuits, with an RS of 7.7 Ω. The second is a Schottky diode of identical characteristics, save the R S of 1.0 Ω. For the conventional diode, the relatively high value of RS causes the voltage across the diode’s terminals to rise as current increases. The power dissipated in the diode heats the junction, causing RS to climb, giving rise to a runaway thermal condition. In the second diode with low RS, such heating does not take place and the voltage across the diode terminals is main8 TJ = junction temperature The key factors in these equations are: RS, the series resistance of the diode where heat is generated under high current conditions; θchip, the chip thermal resistance of the Schottky die; and θ package, or the package thermal resistance. RS for the HSMS-270x family of diodes is typically 0.7 Ω and is the lowest of any Schottky diode available from Avago. Chip thermal resistance is typically 40°C/W; the thermal resistance of the iron-alloy-leadframe, SOT-23 package is typically 460°C/W; and the thermal resistance of the copper-leadframe, SOT-323 package is typically 110°C/W. The impact of package thermal resistance on the current handling capability of these diodes can be seen in Figures 3 and 4. Here the computed values of junction temperature vs. forward current are shown for three values of ambient temperature. The SOT-323 products, with their copper leadframes, can safely handle almost twice the current of the larger SOT-23 diodes. Note that the term “ambient temperature” refers to the temperature of the diode’s leads, not the air around the circuit board. It can be seen that the HSMS-270B and HSMS-270C products in the SOT-323 package will safely withstand a steady-state forward current of 550 mA when the diode’s terminals are maintained at 75°C. Part Number Ordering Information Part Number No. of Devices Container HSMS-2700-BLKG HSMS-2700-TR1G HSMS-2700-TR2G 100 3,000 10,000 Antistatic Bag 7" Reel 13" Reel HSMS-2702-BLKG HSMS-2702-TR1G HSMS-2702-TR2G 100 3,000 10,000 Antistatic Bag 7" Reel 13" Reel For pulsed currents and transient current spikes of less than one microsecond in duration, the junction does not have time to reach thermal steady state. Moreover, the diode junction may be taken to temperatures higher than 150°C for short time-periods without impacting device MTTF. Because of these factors, higher currents can be safely handled. The HSMS-270x family has the highest current handling capability of any Avago diode. HSMS-270B-BLKG HSMS-270B-TR1G HSMS-270B-TR2G 100 3,000 10,000 Antistatic Bag 7" Reel 13" Reel HSMS-270C-BLKG HSMS-270C-TR1G HSMS-270C-TR2G 100 3,000 10,000 Antistatic Bag 7" Reel 13" Reel HSMS-270P-BLKG HSMS-270P-TR1G 100 3,000 Antistatic Bag 7" Reel For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright © 2005-2010 Avago Technologies Limited. All rights reserved. Obsoletes 5989-0473EN AV02-1366EN - July 7, 2010