M54HCT273 M74HCT273 OCTAL D TYPE FLIP FLOP WITH CLEAR . . . . . . . HIGH SPEED fMAX = 80 MHz (TYP.) AT VCC = 5 V LOW POWER DISSIPATION ICC = 4 µA (MAX.) AT TA = 25 °C COMPATIBLE WITH TTL OUTPUTS VIH = 2V (MIN.) VIL = 0.8V (MAX) OUTPUT DRIVE CAPABILITY 10 LSTTL LOADS SYMMETRICAL OUTPUT IMPEDANCE IOH = IOL = 4 mA (MIN.) BALANCED PROPAGATION DELAYS tPLH = tPHL PIN AND FUNCTION COMPATIBLE WITH 54/74LS273 DESCRIPTION The M54/74HCT273 is a high speed CMOS OCTAL D-TYPE FLIP FLOP WITH CLEAR fabricated in sili2 con gate C MOS technology. It has the same high speed performance of LSTTL combined with true CMOS low power consumption. Information signals applied to D inputs are transferred to the Q outputs on the positive-going edge of the clock pulse. When the CLEAR input is held low, the Q output are in the low logic level independent of the other inputs. All inputs are equipped with protection circuits against static discharge and transient excess voltage. This integrated circuit has input and output characteristics that are fully compatible with 54/74 LSTTL logic families. M54/74HCT devices are de2 signed to directly interface HSC MOS systems with TTL and NMOS components. They are also plug in replacements for LSTTL devices giving a reduction of power consumption. All inputs are equipped with protection circuits against static discharge and transient excess voltage. B1R (Plastic Package) F1R (Ceramic Package) M1R (Micro Package) C1R (Chip Carrier) ORDER CODES : M54HCT273F1R M74HCT273M1R M74HCT273B1R M74HCT273C1R PIN CONNECTIONS (top view) INPUT AND OUTPUT EQUIVALENT CIRCUIT NC = No Internal Connection February 1993 1/10 M54/M74HCT273 PIN DESCRIPTION IEC LOGIC SYMBOL PIN No SYMBOL 1 CLEAR 2, 5, 6, 9, 12, 15, 16, 19 3, 4, 7, 8, 13, 14, 17, 18 11 Q0 to Q7 Master Reset Input (Active LOW) Flip Flop Outputs NAME AND FUNCTION D0 to D7 Data Inputs CLOCK 10 GND Clock Input (LOW to HIGH, Edge Triggered) Ground (0V) 20 V CC Positive Supply Voltage TRUTH TABLE CLEAR INPUTS CLOCK D L X FUNCTION CLEAR X L H H L H L H H X Qn X: Don’t Care LOGIC DIAGRAM 2/10 OUTPUS QA NO CHANGE M54/M74HCT273 ABSOLUTE MAXIMUM RATINGS Symbol Value Unit VCC VI Supply Voltage DC Input Voltage -0.5 to +7 -0.5 to VCC + 0.5 V V VO DC Output Voltage -0.5 to VCC + 0.5 V IIK IOK DC Input Diode Current DC Output Diode Current ± 20 ± 20 mA mA IO DC Output Source Sink Current Per Output Pin ± 25 mA DC VCC or Ground Current ± 50 mA 500 (*) mW ICC or IGND Parameter PD Power Dissipation Tstg TL Storage Temperature Lead Temperature (10 sec) -65 to +150 300 o o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied. (*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage VI Input Voltage VO Top Output Voltage Operating Temperature: M54HC Series M74HC Series Input Rise and Fall Time (VCC = 4.5 to 5.5V) tr, tf Value 4.5 to 5.5 Unit V 0 to VCC V 0 to VCC -55 to +125 -40 to +85 0 to 500 V C o C ns o 3/10 M54/M74HCT273 DC SPECIFICATIONS Test Conditions Symbol Parameter VCC (V) VIH High Level Input Voltage 4.5 to 5.5 V IL Low Level Input Voltage 4.5 to 5.5 V OH High Level Output Voltage VOL II ICC ∆ICC 4/10 Low Level Output Voltage Input Leakage Current Quiescent Supply Current Additional worst case supply current Value TA = 25 oC 54HC and 74HC Min. Typ. Max. 2.0 -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 2.0 0.8 4.5 VI = IO=-20 µA VIH or IO=-4.0 mA V IL 4.5 VI = IO= 20 µA VIH or IO= 4.0 mA V IL 2.0 0.8 V 0.8 4.4 4.5 4.4 4.4 4.18 4.31 4.13 4.10 Unit V V 0.0 0.1 0.1 0.1 0.17 0.26 0.33 0.4 VI = VCC or GND ±0.1 ±1 ±1 µA 5.5 VI = VCC or GND 4 40 80 µA 5.5 Per Input pin VI = 0.5V or V I = 2.4V Other Inputs at V CC or GND IO= 0 2.0 2.9 3.0 mA 5.5 V M54/M74HCT273 AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns) Test Conditions Value -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 19 22 Symbol Parameter VCC (V) tTLH tTHL tPLH tPHL Output Transition Time Propagation Delay Time (CLOCK - Q) Propagation Delay Time (CLEAR - Q) Maximum Clock Frequency Input Capacitance Power Dissipation Capacitance 4.5 TA = 25 oC 54HC and 74HC Min. Typ. Max. 9 15 4.5 19 30 38 45 ns 4.5 22 32 40 48 ns tPLH tPHL fMAX CIN CPD (*) 4.5 30 71 5 29 24 10 Unit ns MHz 10 10 pF pF (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC/8 (per Flip FLop), and the total CPD when n pcs of Flip Flop operate can be gained by the following equations: CPD (total) = 32 + 11 x n SWITCHING CHARACTERISTICS TEST WAVEFORM TEST CIRCUIT ICC (Opr.) 5/10 M54/M74HCT273 Plastic DIP20 (0.25) MECHANICAL DATA mm DIM. MIN. a1 0.254 B 1.39 TYP. inch MAX. MIN. TYP. MAX. 0.010 1.65 0.055 0.065 b 0.45 0.018 b1 0.25 0.010 D 25.4 1.000 E 8.5 0.335 e 2.54 0.100 e3 22.86 0.900 F 7.1 0.280 I 3.93 0.155 L Z 3.3 0.130 1.34 0.053 P001J 6/10 M54/M74HCT273 Ceramic DIP20 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 25 0.984 B 7.8 0.307 D E 3.3 0.5 e3 0.130 1.78 0.020 22.86 0.070 0.900 F 2.29 2.79 0.090 0.110 G 0.4 0.55 0.016 0.022 I 1.27 1.52 0.050 0.060 L 0.22 0.31 0.009 0.012 M 0.51 1.27 0.020 0.050 N1 P Q 4° (min.), 15° (max.) 7.9 8.13 5.71 0.311 0.320 0.225 P057H 7/10 M54/M74HCT273 SO20 MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 2.65 0.10 0.104 0.20 a2 MAX. 0.004 0.007 2.45 0.096 b 0.35 0.49 0.013 0.019 b1 0.23 0.32 0.009 0.012 C 0.50 0.020 c1 45° (typ.) D 12.60 13.00 0.496 0.512 E 10.00 10.65 0.393 0.419 e 1.27 0.050 e3 11.43 0.450 F 7.40 7.60 0.291 0.299 L 0.50 1.27 0.19 0.050 M S 0.75 0.029 8° (max.) P013L 8/10 M54/M74HCT273 PLCC20 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 9.78 10.03 0.385 0.395 B 8.89 9.04 0.350 0.356 D 4.2 4.57 0.165 0.180 d1 2.54 0.100 d2 0.56 0.022 E 7.37 8.38 0.290 0.330 e 1.27 0.050 e3 5.08 0.200 F 0.38 0.015 G 0.101 0.004 M 1.27 0.050 M1 1.14 0.045 P027A 9/10 M54/M74HCT273 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 10/10