NCP715 50 mA Ultra-Low Iq, Wide Input Voltage, Low Dropout Linear Voltage Regulator The NCP715 is 50 mA LDO Linear Voltage Regulator. It is a very stable and accurate device with ultra−low ground current consumption (4.7 mA over the full output load range) and a wide input voltage range (up to 24 V). The regulator incorporates several protection features such as Thermal Shutdown and Current Limiting. www.onsemi.com MARKING DIAGRAMS Features • Operating Input Voltage Range: 2.5 V to 24 V • Fixed Voltage Options Available: 1.2 V to 5.3 V • Ultra Low Quiescent Current: Max. 4.7 mA Over Full Load and • • • • • • Temperature ±2% Accuracy Over Full Load, Line and Temperature Variations PSRR: 52 dB at 100 kHz Noise: 190 mVRMS from 200 Hz to 100 kHz Thermal Shutdown and Current Limit protection Available in XDFN6 1.5 x 1.5 mm and SC−70 (SC−88A) Package These are Pb−Free Devices Typical Applications • Portable Equipment • Communication Systems 1.2 V < Vout < 5.3 V 2.5 V < Vout < 24 V OUT IN 1 mF Ceramic NCP715 NC GND NC XDFN6 CASE 711AE SC−70−5 (SC−88A) CASE 419A 1 XX MG G XX MG G XX = Specific Device Code M = Date Code G = Pb−Free Package (Note: Microdot may be in either location) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 18 of this data sheet. 1 mF Ceramic Figure 1. Typical Application Schematic © Semiconductor Components Industries, LLC, 2016 June, 2016 − Rev. 4 1 Publication Order Number: NCP715/D NCP715 IN THERMAL SHUTDOWN UVLO BANDGAP REFERENCE MOSFET DRIVER WITH CURRENT LIMIT OUT EEPROM GND Figure 2. Simplified Block Diagram Figure 3. Pin Description PIN FUNCTION DESCRIPTION Pin No. SC−70 XDFN6 Pin Name 5 6 OUT Regulated output voltage pin. A small 0.47 mF ceramic capacitor is needed from this pin to ground to assure stability. 1 2 N/C No connection. This pin can be tied to ground to improve thermal dissipation or left disconnected. 2 3 GND Power supply ground. 3 4 N/C No connection. This pin can be tied to ground to improve thermal dissipation or left disconnected. − 5 N/C No connection. This pin can be tied to ground to improve thermal dissipation or left disconnected. 4 1 IN Description Input pin. A small capacitor is needed from this pin to ground to assure stability. www.onsemi.com 2 NCP715 ABSOLUTE MAXIMUM RATINGS Rating Input Voltage (Note 1) Output Voltage Output Short Circuit Duration Maximum Junction Temperature Operating Ambient Temperature Range Symbol Value Unit VIN −0.3 to 24 V VOUT −0.3 to 6 V tSC Indefinite s TJ(MAX) 150 °C TA −40 to 125 °C TSTG −55 to 150 °C ESD Capability, Human Body Model (Note 2) ESDHBM 2000 V ESD Capability, Machine Model (Note 2) ESDMM 200 V Storage Temperature Range Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area. 2. This device series incorporates ESD protection and is tested by the following methods: ESD Human Body Model tested per EIA/JESD22−A114 ESD Machine Model tested per EIA/JESD22−A115 ESD Charged Device Model tested per EIA/JESD22−C101E Latch up Current Maximum Rating tested per JEDEC standard: JESD78. THERMAL CHARACTERISTICS Rating Symbol Value Unit Thermal Characteristics, SC−70 Thermal Resistance, Junction−to−Air RqJA 390 °C/W Thermal Characteristics, XDFN6 Thermal Resistance, Junction−to−Air RqJA 260 °C/W www.onsemi.com 3 NCP715 ELECTRICAL CHARACTERISTICS − Voltage Version 1.2 V −40°C ≤ TJ ≤ 125°C; VIN = 2.5 V; IOUT = 1 mA, CIN = COUT = 1.0 mF, unless otherwise noted. Typical values are at TJ = +25°C. (Note 5) Parameter Operating Input Voltage Test Conditions Symbol Min IOUT ≤ 10 mA VIN 10 mA< IOUT < 50 mA Output Voltage Accuracy Typ Max Unit 2.5 24 V 3.0 24 2.5 V < VIN < 24 V, 0 < IOUT ≤ 10 mA VOUT 1.164 1.2 1.236 V 3.0 V < VIN < 24 V, 0 mA < IOUT < 50 mA VOUT 1.164 1.2 1.236 V 3.0 V < VIN < 24 V, 1 mA < IOUT < 50 mA, −20°C < TJ < 125°C; VOUT 1.176 1.2 1.224 V Line Regulation 2.5 V ≤ VIN ≤ 24 V, IOUT = 1 mA RegLINE 2 mV Load Regulation IOUT = 0 mA to 50 mA RegLOAD 5 mV Dropout Voltage (Note 3) Maximum Output Current VDO (Note 6) IOUT 0 < IOUT < 50 mA, −40 < TA < 85°C IGND 100 3.2 0 < IOUT < 50 mA, VIN = 24 V Power Supply Rejection Ratio Output Noise Voltage Thermal Shutdown Temperature (Note 4) Thermal Shutdown Hysteresis (Note 4) VIN = 3.0 V, VOUT = 1.2 V VPP = 200 mV modulation IOUT = 1 mA, COUT= 10 mF f = 100 kHz − mV 200 mA 4.2 mA 5.8 PSRR 60 dB VOUT = 1.2 V, IOUT = 50 mA f = 200 Hz to 100 kHz, COUT = 10 mF VN 65 mVrms Temperature increasing from TJ = +25°C TSD 170 °C Temperature falling from TSD TSDH − 15 − °C 3. Not Characterized at VIN = 3.0 V, VOUT = 1.2 V, IOUT = 50 mA. 4. Guaranteed by design and characterization. 5. Performance guaranteed over the indicated operating temperature range by design and/or characterization production tested at TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 6. Respect SOA. www.onsemi.com 4 NCP715 ELECTRICAL CHARACTERISTICS − Voltage Version 1.5 V −40°C ≤ TJ ≤ 125°C; VIN = 2.5 V; IOUT = 1 mA, CIN = COUT = 1.0 mF, unless otherwise noted. Typical values are at TJ = +25°C. (Note 9) Parameter Operating Input Voltage Test Conditions Symbol Min IOUT ≤ 10 mA VIN 10 mA < IOUT < 50 mA Output Voltage Accuracy Typ Max Unit 2.5 24 V 3.0 24 2.5 V < VIN < 24 V, 0 < IOUT ≤ 10 mA VOUT 1.455 1.5 1.545 V 3.0 V < VIN < 24 V, 0 < IOUT < 50 mA VOUT 1.455 1.5 1.545 V 3.0 V < VIN < 24 V, 1 mA < IOUT < 50 mA, −20°C < TJ < 125°C; VOUT 1.470 1.5 1.530 V Line Regulation VOUT + 1 V ≤ VIN ≤ 24 V, IOUT = 1 mA RegLINE 2 mV Load Regulation IOUT = 0 mA to 50 mA RegLOAD 5 mV Dropout Voltage (Note 7) Maximum Output Current Ground Current VDO (Note 10) IOUT 0 < IOUT < 50 mA, −40 < TA < 85°C IGND 100 3.2 0 < IOUT < 50 mA, VIN = 24 V Power Supply Rejection Ratio Output Noise Voltage Thermal Shutdown Temperature (Note 8) Thermal Shutdown Hysteresis (Note 8) VIN = 3.0 V, VOUT = 1.5 V VPP = 200 mV modulation IOUT = 1 mA, COUT = 10 mF f = 100 kHz − mV 200 mA 4.2 mA 5.8 mA PSRR 56 dB VOUT = 1.5 V, IOUT = 50 mA f = 200 Hz to 100 kHz, COUT = 10 mF VN 75 mVrms Temperature increasing from TJ = +25°C TSD 170 °C Temperature falling from TSD TSDH − 15 − °C 7. Not Characterized at VIN = 3.0 V, VOUT = 1.5 V, IOUT = 50 mA. 8. Guaranteed by design and characterization. 9. Performance guaranteed over the indicated operating temperature range by design and/or characterization production tested at TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 10. Respect SOA. www.onsemi.com 5 NCP715 ELECTRICAL CHARACTERISTICS − Voltage Version 1.8 V −40°C ≤ TJ ≤ 125°C; VIN = 2.8V; IOUT = 1 mA, CIN = COUT = 1.0 mF, unless otherwise noted. Typical values are at TJ = +25°C. (Note 13) Parameter Operating Input Voltage Test Conditions Symbol Min IOUT ≤10 mA VIN 10 mA < IOUT < 50 mA Output Voltage Accuracy Typ Max Unit 2.8 24 V 3.0 24 2.8 V < VIN < 24 V, 0 < IOUT < 10 mA VOUT 1.746 1.8 1.854 V 3.0 V < VIN < 24 V, 1 mA < IOUT < 50 mA, −20°C < TJ < 125°C; VOUT 1.764 1.8 1.836 V Line Regulation 3 V ≤ VIN ≤ 24 V, IOUT = 1 mA RegLINE 3 mV Load Regulation IOUT = 0 mA to 50 mA RegLOAD 10 mV Dropout Voltage (Note 11) Maximum Output Current Ground Current VDO (Note 14) IOUT 0 < IOUT < 50 mA, −40 < TA < 85°C IGND mV 100 3.2 0 < IOUT < 50 mA, VIN = 24 V Power Supply Rejection Ratio Output Noise Voltage Thermal Shutdown Temperature (Note 12) Thermal Shutdown Hysteresis (Note 12) VIN = 3.0 V, VOUT = 1.8 V VPP = 200 mV modulation IOUT = 1 mA, COUT =10 mF f = 100 kHz 200 mA 4.2 mA 5.8 mA PSRR 60 dB VOUT = 1.8 V, IOUT = 50 mA f = 200 Hz to 100 kHz, COUT = 10 mF VN 95 mVrms Temperature increasing from TJ = +25°C TSD 170 °C Temperature falling from TSD TSDH − 15 − °C 11. Not characterized at VIN = 3.0 V, VOUT = 1.8 V, IOUT = 50 mA 12. Guaranteed by design and characterization. 13. Performance guaranteed over the indicated operating temperature range by design and/or characterization production tested at TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 14. Respect SOA. www.onsemi.com 6 NCP715 ELECTRICAL CHARACTERISTICS − Voltage Version 2.5 V −40°C ≤ TJ ≤ 125°C; VIN = 3.5 V; IOUT = 1 mA, CIN = COUT = 1.0 mF, unless otherwise noted. Typical values are at TJ = +25°C. (Note 17) Parameter Test Conditions Symbol Min Operating Input Voltage 0 < IOUT < 50 mA VIN 3.5 Output Voltage Accuracy 3.5 V < VIN < 24 V, 0 < IOUT < 50 mA VOUT 2.45 Line Regulation VOUT + 1 V ≤ VIN ≤ 24 V, IOUT = 1 mA RegLINE 3 mV Load Regulation IOUT = 0 mA to 50 mA RegLOAD 10 mV Dropout Voltage (Note 15) VDO = VIN – (VOUT(NOM) – 75 mV) IOUT = 50 mA VDO 260 Maximum Output Current (Note 18) IOUT 0 < IOUT < 50 mA, −40 < TA < 85°C IGND Ground Current Power Supply Rejection Ratio Output Noise Voltage Thermal Shutdown Temperature (Note 16) Thermal Shutdown Hysteresis (Note 16) Typ 2.5 100 3.2 0 < IOUT < 50 mA, VIN = 24 V VIN = 3.5 V, VOUT = 2.5 V VPP = 200 mV modulation IOUT = 1 mA, COUT =10 mF f = 100 kHz Max Unit 24 V 2.55 V 450 mV 200 mA 4.2 mA 5.8 mA PSRR 60 dB VOUT = 2.5 V, IOUT = 50 mA f = 200 Hz to 100 kHz, COUT = 10 mF VN 115 mVrms Temperature increasing from TJ = +25°C TSD 170 °C Temperature falling from TSD TSDH − 15 − °C 15. Characterized when VOUT falls 75 mV below the regulated voltage and only for devices with VOUT = 2.5 V. 16. Guaranteed by design and characterization. 17. Performance guaranteed over the indicated operating temperature range by design and/or characterization production tested at TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 18. Respect SOA. www.onsemi.com 7 NCP715 ELECTRICAL CHARACTERISTICS − Voltage Version 3.0 V −40°C ≤ TJ ≤ 125°C; VIN = 4.0 V; IOUT = 1 mA, CIN = COUT = 1.0 mF, unless otherwise noted. Typical values are at TJ = +25°C. (Note 21) Parameter Test Conditions Symbol Min Operating Input Voltage 0 < IOUT < 50 mA VIN 4.0 Output Voltage Accuracy 4.0 V < VIN < 24 V, 0< IOUT < 50 mA VOUT 2.94 Typ 3.0 Max Unit 24 V 3.06 V Line Regulation VOUT + 1 V ≤ VIN ≤ 24 V, IOUT = 1 mA RegLINE 3 mV Load Regulation IOUT = 0 mA to 50 mA RegLOAD 10 mV VDO = VIN – (VOUT(NOM) – 90 mV) IOUT = 50 mA VDO Dropout voltage (Note 19) Maximum Output Current Ground current (Note 22) IOUT 0 < IOUT < 50 mA, -40 < TA < 85°C IGND 100 3.2 0 < IOUT < 50 mA, VIN = 24 V Power Supply Rejection Ratio Output Noise Voltage Thermal Shutdown Temperature (Note 20) Thermal Shutdown Hysteresis (Note 20) VIN = 4.0 V, VOUT = 3.0 V VPP = 100 mV modulation IOUT = 1 mA, COUT = 10 mF f = 100 kHz 400 mV 200 mA 4.2 mA 5.8 mA 250 PSRR 60 dB VOUT = 3 V, IOUT = 50 mA, f = 200 Hz to 100 kHz, COUT = 10 mF VN 135 mVrms Temperature increasing from TJ = +25°C TSD 170 °C Temperature falling from TSD TSDH - 25 - °C 19. Characterized when VOUT falls 90 mV below the regulated voltage and only for devices with VOUT = 3.0 V 20. Guaranteed by design and characterization. 21. Performance guaranteed over the indicated operating temperature range by design and/or characterization production tested at TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 22. Respect SOA www.onsemi.com 8 NCP715 ELECTRICAL CHARACTERISTICS − Voltage Version 3.3 V −40°C ≤ TJ ≤ 125°C; VIN = 4.3 V; IOUT = 1 mA, CIN = COUT = 1.0 mF, unless otherwise noted. Typical values are at TJ = +25°C. (Note 25) Parameter Test Conditions Symbol Min Operating Input Voltage 0 < IOUT < 50 mA VIN 4.3 Output Voltage Accuracy 4.3 V < VIN < 24 V, 0 < IOUT < 50 mA VOUT 3.234 Line Regulation VOUT + 1 V ≤ VIN ≤ 24 V, IOUT = 1 mA Load Regulation IOUT = 0 mA to 50 mA VDO = VIN – (VOUT(NOM) – 99 mV) IOUT = 50 mA VDO 230 Dropout Voltage (Note 23) Maximum Output Current Ground Current Max Unit 24 V 3.3 3.366 V RegLINE 3 10 mV RegLOAD 10 (Note 26) IOUT 0 < IOUT < 50 mA, −40 < TA < 85°C IGND Typ 100 3.2 0 < IOUT < 50 mA, VIN = 24 V Power Supply Rejection Ratio Output Noise Voltage Thermal Shutdown Temperature (Note 24) Thermal Shutdown Hysteresis (Note 24) VIN = 4.3 V, VOUT = 3.3 V VPP = 200 mV modulation IOUT = 1 mA, COUT =10 mF f = 100 kHz mV 350 mV 200 mA 4.2 mA 5.8 mA PSRR 60 dB VOUT = 4.3 V, IOUT = 50 mA f = 200 Hz to 100 kHz, COUT = 10 mF VN 140 mVrms Temperature increasing from TJ = +25°C TSD 170 °C Temperature falling from TSD TSDH − 15 − °C 23. Characterized when VOUT falls 99 mV below the regulated voltage and only for devices with VOUT = 3.3 V. 24. Guaranteed by design and characterization. 25. Performance guaranteed over the indicated operating temperature range by design and/or characterization production tested at TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 26. Respect SOA. www.onsemi.com 9 NCP715 ELECTRICAL CHARACTERISTICS − Voltage Version 5.0 V −40°C ≤ TJ ≤ 125°C; VIN = 6.0 V; IOUT = 1 mA, CIN = COUT = 1 mF, unless otherwise noted. Typical values are at TJ = +25°C. (Note 29) Parameter Test Conditions Symbol Min Operating Input Voltage 0 < IOUT < 50 mA VIN 6.0 Output Voltage Accuracy 6.0V < VIN < 24V, 0< IOUT < 50 mA VOUT 4.9 Line Regulation VOUT + 1 V ≤ VIN ≤ 24 V, Iout = 1mA Load Regulation IOUT = 0 mA to 50 mA VDO = VIN – (VOUT(NOM) – 150 mV) IOUT = 50 mA VDO Dropout Voltage (Note 27) Maximum Output Current Ground Current Max Unit 24 V 5.0 5.1 V RegLINE 3 10 mV RegLOAD 10 30 mV 230 350 mV 200 mA 4.2 mA 5.8 mA (Note 30) IOUT 0 < IOUT < 50 mA, −40 < TA < 85°C IGND Typ 90 3.2 0 < IOUT < 50 mA, VIN = 24 V Power Supply Rejection Ratio Output Noise Voltage Thermal Shutdown Temperature (Note 28) Thermal Shutdown Hysteresis (Note 28) VIN = 6.0 V, VOUT = 5.0 V VPP = 200 mV modulation IOUT = 1 mA, COUT =10 mF f = 100 kHz PSRR 56 dB VOUT = 5.0 V, IOUT = 50 mA f = 200 Hz to 100 kHz, COUT = 10 mF VN 190 mVrms Temperature increasing from TJ = +25°C TSD 170 °C Temperature falling from TSD TSDH − 15 − °C 27. Characterized when VOUT falls 150 mV below the regulated voltage and only for devices with VOUT = 5.0 V. 28. Guaranteed by design and characterization. 29. Performance guaranteed over the indicated operating temperature range by design and/or characterization production tested at TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 30. Respect SOA. www.onsemi.com 10 NCP715 ELECTRICAL CHARACTERISTICS − Voltage Version 5.3 V −40°C ≤ TJ ≤ 125°C; VIN = 6.3 V; IOUT = 1 mA, CIN = COUT = 1 mF, unless otherwise noted. Typical values are at TJ = +25°C. (Note 33) Parameter Test Conditions Symbol Min Operating Input Voltage 0 < IOUT < 50 mA VIN 6.3 Output Voltage Accuracy 6.3V < VIN < 24V, 0.1 mA< IOUT < 50 mA VOUT 5.194 Typ Max Unit 24 V 5.3 5.406 V 60 mV Line Regulation VOUT + 1 V ≤ VIN ≤ 24 V, IOUT = 1mA RegLINE 20 Load Regulation IOUT = 0.1 mA to 50 mA RegLOAD 20 VDO = VIN – (VOUT(NOM) – 159 mV) IOUT = 50 mA VDO 230 Dropout Voltage (Note 31) Maximum Output Current Ground Current (Note 34) IOUT 0 < IOUT < 50 mA, −40 < TA < 85°C IGND 90 3.2 0 < IOUT < 50 mA, VIN = 24 V Power Supply Rejection Ratio Output Noise Voltage Thermal Shutdown Temperature (Note 32) Thermal Shutdown Hysteresis (Note 32) VIN = 6.3 V, VOUT = 5.3 V VPP = 200 mV modulation IOUT = 1 mA, COUT =10 mF f = 100 kHz mV 350 mV 200 mA 4.2 mA 5.8 mA PSRR 55 dB VOUT = 5.3 V, IOUT = 50 mA f = 200 Hz to 100 kHz, COUT = 10 mF VN 195 mVrms Temperature increasing from TJ = +25°C TSD 170 °C Temperature falling from TSD TSDH − 15 − °C 31. Characterized when VOUT falls 159 mV below the regulated voltage and only for devices with VOUT = 5.3 V. 32. Guaranteed by design and characterization. 33. Performance guaranteed over the indicated operating temperature range by design and/or characterization production tested at TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 34. Respect SOA. www.onsemi.com 11 NCP715 1.2 2.506 VIN = 3.0 V 1.198 1.197 1.196 VIN = (5.0 − 24.0) V 1.195 1.194 1.193 1.192 −40 NCP715x12xxx CIN = COUT = 1 mF IOUT = 1 mA −20 0 20 VIN = 3.0 V 2.504 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 1.199 2.502 2.5 VIN = (5.0 − 24.0) V 2.498 2.496 2.494 NCP715x25xxx CIN = COUT = 1 mF IOUT = 1 mA 2.492 40 60 80 100 2.49 −40 120 −20 0 3.315 5.015 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 5.02 3.312 3.309 3.306 3.303 3.294 −40 NCP715x33xxx CIN = COUT = 1 mF IOUT = 1 mA VIN = 4.3 V to 24 V −20 0 20 40 60 80 TEMPERATURE (°C) 100 VIN = 6.0 V 4.995 NCP715x50xxx CIN = COUT = 1 mF IOUT = 1 mA 4.99 0 20 40 60 80 100 JUNCTION TEMPERATURE (°C) 1.192 1.188 VIN = 3.0 V VIN = 5.0 V VIN = 10 V VIN = 15 V VIN = 20 V VIN = 24 V 1.176 1.172 0 10 20 30 OUTPUT CURRENT (mA) NCP715x25xxx CIN = COUT = 1 mF TA = 25°C 2.500 2.496 2.492 2.488 VIN = 3.5 V VIN = 5.0 V VIN = 10 V VIN = 15 V VIN = 20 V VIN = 24 V 2.484 2.480 2.476 2.472 40 120 Figure 7. Output Voltage vs. Temperature OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) −20 2.504 1.180 120 5 4.98 −40 120 NCP715x12xxx CIN = COUT = 1 mF TA = 25°C 1.184 100 5.005 4.985 1.204 1.196 80 VIN = (8.0 − 24.0) V 5.01 Figure 6. Output Voltage vs. Temperature 1.200 60 Figure 5. Output Voltage vs. Temperature 3.318 3.297 40 TEMPERATURE (°C) TEMPERATURE (°C) Figure 4. Output Voltage vs. Temperature 3.3 20 50 0 Figure 8. Output Voltage vs. Output Current 10 20 30 OUTPUT CURRENT (mA) 40 Figure 9. Output Voltage vs. Output Current www.onsemi.com 12 50 NCP715 3.312 OUTPUT VOLTAGE (V) 3.308 3.304 3.300 3.296 3.292 VIN = 4.3 V VIN = 10 V VIN = 15 V VIN = 20 V VIN = 24 V 3.288 3.284 5.016 NCP715x50xxx CIN = COUT = 1 mF TA = 25°C 5.008 OUTPUT VOLTAGE (V) NCP715x33xxx CIN = COUT = 1 mF TA = 25°C 5.000 4.992 4.984 4.976 VIN = 6.0 V VIN = 10 V VIN = 15 V VIN = 20 V VIN = 24 V 4.968 4.960 3.280 4.952 0 10 20 30 40 0 50 10 OUTPUT CURRENT (mA) Figure 10. Output Voltage vs. Output Current 50 NCP715x33xxx CIN = COUT = 1 mF 350 TA = 125°C 300 250 TA = 25°C 200 150 TA = −40°C 100 DROPOUT VOLTAGE (mV) DROPOUT VOLTAGE (mV) 40 400 NCP715x25xxx CIN = COUT = 1 mF 350 50 300 TA = 125°C 250 TA = 25°C 200 150 100 TA = −40°C 50 0 0 0 10 20 30 40 0 50 10 OUTPUT CURRENT (mA) 20 30 40 50 OUTPUT CURRENT (mA) Figure 12. Dropout Voltage vs. Output Current Figure 13. Dropout Voltage vs. Output Current 400 40 GND, QUIESCENT CURRENT (mA) NCP715x50xxx CIN = COUT = 1 mF 350 DROPOUT VOLTAGE (mV) 30 Figure 11. Output Voltage vs. Output Current 400 300 TA = 125°C 250 200 TA = 25°C 150 100 TA = −40°C 50 0 20 OUTPUT CURRENT (mA) 0 10 20 30 40 50 NCP715x12xxx CIN = COUT = 1 mF TA = 25°C 35 30 25 20 15 IOUT = 0 IOUT = 50 mA 10 5 0 0 5 10 15 20 OUTPUT CURRENT (mA) INPUT VOLTAGE (V) Figure 14. Dropout Voltage vs. Output Current Figure 15. Ground Current vs. Input Voltage www.onsemi.com 13 25 NCP715 40 IOUT = 0 IOUT = 50 mA 35 NCP715x25xxx CIN = COUT = 1 mF TA = 25°C 30 GND, QUIESCENT CURRENT (mA) GND, QUIESCENT CURRENT (mA) 40 25 20 15 10 5 0 30 25 20 15 10 5 0 0 5 10 15 20 25 0 5 10 INPUT VOLTAGE (V) 20 25 Figure 17. Ground Current vs. Input Voltage 4.5 40 NCP715x50xxx CIN = COUT = 1 mF TA = 25°C IOUT = 0 IOUT = 50 mA 35 30 QUIESCENT CURRENT (mA) GND, QUIESCENT CURRENT (mA) 15 INPUT VOLTAGE (V) Figure 16. Ground Current vs. Input Voltage 25 20 15 10 5 0 5 10 15 20 4.3 4.0 3.8 3.5 3.3 3.0 2.8 2.5 −40 0 25 VIN = 3 V VIN = 10 V VIN = 24 V −20 0 INPUT VOLTAGE (V) NCP715x12xxx CIN = COUT = 1 mF IOUT = 0 20 40 60 80 100 120 TEMPERATURE (°C) Figure 18. Ground Current vs. Input Voltage Figure 19. Quiescent Current vs. Temperature 6.0 6.0 NCP715x25xxx CIN = COUT = 1 mF IOUT = 0 5.5 5.0 QUIESCENT CURRENT (mA) QUIESCENT CURRENT (mA) NCP715x33xxx CIN = COUT = 1 mF TA = 25°C IOUT = 0 IOUT = 50 mA 35 4.5 4.0 3.5 3.0 VIN = 3.5 V VIN = 10 V VIN = 24 V 2.5 2.0 −40 −20 0 20 40 60 80 100 NCP715x33xxx CIN = COUT = 1 mF IOUT = 0 5.5 5.0 4.5 4.0 3.5 3.0 VIN = 4.3 V VIN = 10 V VIN = 24 V 2.5 2.0 −40 120 −20 0 20 40 60 80 100 120 TEMPERATURE (°C) TEMPERATURE (°C) Figure 20. Quiescent Current vs. Temperature Figure 21. Quiescent Current vs. Temperature www.onsemi.com 14 NCP715 100 NCP715x50xxx CIN = COUT = 1 mF IOUT = 0 5.5 5.0 4.5 4.0 3.5 3.0 VIN = 6 V VIN = 10 V VIN = 24 V 2.5 2.0 −40 PSRR (dB) 80 0 40 IOUT = 10 mA 0 20 40 60 80 100 0.1 120 1 10 100 TEMPERATURE (°C) FREQUENCY (kHz) Figure 22. Quiescent Current vs. Temperature Figure 23. PSRR vs. Frequency 100 NCP715x25xxx COUT = 10 mF VIN = 3.5 V + 200 mVPP Modulation TA = 25°C IOUT = 1 mA IOUT = 50 mA NCP715x33xxx COUT = 10 mF VIN = 4.3 V + 200 mVPP Modulation TA = 25°C 80 40 20 1000 IOUT = 1 mA 60 40 20 IOUT = 10 mA IOUT = 10 mA IOUT = 50 mA 0 0 0.1 1 10 100 0.1 1000 10 100 FREQUENCY (kHz) Figure 24. PSRR vs. Frequency Figure 25. PSRR vs. Frequency 1.6 OUTPUT VOLTAGE NOISE (mV/√Hz) NCP715x50xxx COUT = 10 mF VIN = 6.0 V + 200 mVPP Modulation TA = 25°C IOUT = 1 mA 60 40 20 IOUT = 50 mA IOUT = 10 mA 0 0.1 1 FREQUENCY (kHz) 100 PSRR (dB) IOUT = 1 mA IOUT = 50 mA 60 80 60 20 PSRR (dB) 100 −20 NCP715x12xxx COUT = 10 mF VIN = 3.0 V + 200 mVPP Modulation TA = 25°C 80 PSRR (dB) QUIESCENT CURRENT (mA) 6.0 1 10 100 1000 1000 COUT = 10 mF, 65.1 mVrms @ 200 Hz − 100 kHz 1.4 COUT = 4.7 mF, 80.5 mVrms @ 200 Hz − 100 kHz 1.2 COUT = 1.0 mF, 172.1 mVrms @ 200 Hz − 100 kHz 1.0 COUT = 0.47 mF, 208 mVrms @ 200 Hz − 100 kHz COUT = 2.2 mF, 111.5 mVrms @ 200 Hz − 100 kHz 0.8 0.6 0.4 0.2 NCP715x12xxx IOUT = 50 mA TA = 25°C VIN = 3 V 0.0 0.01 0.1 1 10 100 1000 FREQUENCY (kHz) FREQUENCY (kHz) Figure 26. PSRR vs. Frequency Figure 27. Output Spectral Noise Density vs. Frequency www.onsemi.com 15 NCP715 COUT = 4.7 mF, 128.4 mVrms @ 200 Hz − 100 kHz 3.5 COUT = 2.2 mF, 152.2 mVrms @ 200 Hz − 100 kHz 3.0 COUT = 1.0 mF, 172.1 mVrms @ 200 Hz − 100 kHz COUT = 0.47 mF, 203.6 mVrms @ 200 Hz − 100 kHz 2.5 NCP715x25xxx IOUT = 50 mA TA = 25°C VIN = 3.5 V 2.0 1.5 1.0 0.5 0.0 0.01 0.1 1 10 100 1000 COUT = 10 mF, 137.1 mVrms @ 200 Hz − 100 kHz 4.5 COUT = 4.7 mF, 145.7 mVrms @ 200 Hz − 100 kHz 4.0 COUT = 2.2 mF, 170.6 mVrms @ 200 Hz − 100 kHz 3.5 COUT = 1.0 mF, 220.8 mVrms @ 200 Hz − 100 kHz COUT = 0.47 mF, 271.1 mVrms @ 200 Hz − 100 kHz 3.0 NCP715x33xxx IOUT = 50 mA TA = 25°C VIN = 4.3 V 2.5 2.0 1.5 1.0 0.5 0.0 0.01 0.1 1 10 100 1000 FREQUENCY (kHz) FREQUENCY (kHz) Figure 28. Output Spectral Noise Density vs. Frequency Figure 29. Output Spectral Noise Density vs. Frequency 7.0 OUTPUT VOLTAGE NOISE (mV/√Hz) 5.0 COUT = 10 mF, 114.7 mVrms @ 200 Hz − 100 kHz OUTPUT VOLTAGE NOISE (mV/√Hz) OUTPUT VOLTAGE NOISE (mV/√Hz) 4.0 COUT = 10 mF, 186.1 mVrms @ 200 Hz − 100 kHz COUT = 4.7 mF, 189.41 mVrms @ 200 Hz − 100 kHz 6.0 COUT = 2.2 mF, 207.6 mVrms @ 200 Hz − 100 kHz COUT = 1.0 mF, 244.5 mVrms @ 200 Hz − 100 kHz 5.0 COUT = 0.47 mF, 305.0 mVrms @ 200 Hz − 100 kHz 4.0 NCP715x50xxx IOUT = 50 mA TA = 25°C VIN = 6.0 V 3.0 2.0 1.0 0.0 0.01 0.1 1 10 100 1000 FREQUENCY (kHz) Figure 30. Output Spectral Noise Density vs. Frequency Figure 31. Line Transient Response Figure 32. Line Transient Response Figure 33. Line Transient Response www.onsemi.com 16 NCP715 Figure 34. Load Transient Response Figure 35. Load Transient Response Figure 36. Load Transient Response Figure 37. Input Voltage Turn−On Response Figure 38. Input Voltage Turn−On Response Figure 39. Input Voltage Turn−On Response www.onsemi.com 17 NCP715 APPLICATIONS INFORMATION ambient temperature affect the rate of junction temperature rise for the part. The maximum power dissipation the NCP715 can handle is given by: The NCP715 is the member of new family of Wide Input Voltage Range Low Dropout Regulators which delivers Ultra Low Ground Current consumption, Good Noise and Power Supply Rejection Ratio Performance. P D(MAX) + Input Decoupling (CIN) It is recommended to connect at least 0.1 mF Ceramic X5R or X7R capacitor between IN and GND pin of the device. This capacitor will provide a low impedance path for any unwanted AC signals or Noise superimposed onto constant Input Voltage. The good input capacitor will limit the influence of input trace inductances and source resistance during sudden load current changes. Higher capacitance and lower ESR Capacitors will improve the overall line transient response. ƪTJ(MAX) * TAƫ (eq. 1) R qJA The power dissipated by the NCP715 for given application conditions can be calculated from the following equations: P D [ V INǒI GNDǒI OUTǓǓ ) I OUTǒV IN * V OUTǓ (eq. 2) or V IN(MAX) [ Output Decoupling (COUT) P D(MAX) ) ǒV OUT I OUTǓ I OUT ) I GND (eq. 3) For reliable operation, junction temperature should be limited to +125°C maximum. The NCP715 does not require a minimum Equivalent Series Resistance (ESR) for the output capacitor. The device is designed to be stable with standard ceramics capacitors with values of 0.47 mF or greater up to 10 mF. The X5R and X7R types have the lowest capacitance variations over temperature thus they are recommended. Hints VIN and GND printed circuit board traces should be as wide as possible. When the impedance of these traces is high, there is a chance to pick up noise or cause the regulator to malfunction. Place external components, especially the output capacitor, as close as possible to the NCP715, and make traces as short as possible. Power Dissipation and Heat sinking The maximum power dissipation supported by the device is dependent upon board design and layout. Mounting pad configuration on the PCB, the board material, and the ORDERING INFORMATION Device Nominal Output Voltage Marking NCP715SQ12T2G 1.2 V 5A NCP715SQ15T2G 1.5 V 5C NCP715SQ18T2G 1.8 V 5D NCP715SQ25T2G 2.5 V 5E NCP715SQ30T2G 3.0 V 5F NCP715SQ33T2G 3.3 V 5G NCP715SQ50T2G 5.0 V 5H NCP715MX12TBG 1.2 V Q NCP715MX15TBG 1.5 V R NCP715MX18TBG 1.8 V T NCP715MX25TBG 2.5 V V NCP715MX30TBG 3.0 V Y NCP715MX33TBG 3.3 V 2 NCP715MX50TBG 5.0 V 5 NCP715MX53TBG 5.3 V 5 Marking Rotation Package − SC88A/SC70 (Pb−Free) Shipping† 3000 / Tape & Reel 0° XDFN6 1.5 x 1.5 (Pb−Free) +180° †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. www.onsemi.com 18 NCP715 PACKAGE DIMENSIONS XDFN6 1.5x1.5, 0.5P CASE 711AE ISSUE B D NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.10 AND 0.20mm FROM TERMINAL TIP. L A B L1 PIN ONE REFERENCE 0.10 C 2X 2X 0.10 C ÍÍÍ ÍÍÍ ÍÍÍ DETAIL A ALTERNATE TERMINAL CONSTRUCTIONS E DIM A A1 A3 b D E e L L1 L2 ÉÉÉ ÉÉÉ EXPOSED Cu TOP VIEW MOLD CMPD DETAIL B ALTERNATE CONSTRUCTIONS A DETAIL B 0.05 C A3 A1 MILLIMETERS MIN MAX 0.35 0.45 0.00 0.05 0.13 REF 0.20 0.30 1.50 BSC 1.50 BSC 0.50 BSC 0.40 0.60 --0.15 0.50 0.70 RECOMMENDED MOUNTING FOOTPRINT* 0.05 C 5X C SIDE VIEW DETAIL A e 1 SEATING PLANE 6X 5X 0.73 1.80 L 3 0.35 L2 0.83 0.50 PITCH DIMENSIONS: MILLIMETERS 6 4 6X *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. b 0.10 C A BOTTOM VIEW 0.05 C B NOTE 3 www.onsemi.com 19 NCP715 PACKAGE DIMENSIONS SC−88A (SC−70−5/SOT−353) CASE 419A−02 ISSUE L A G 5 4 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419A−01 OBSOLETE. NEW STANDARD 419A−02. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. −B− S 1 2 DIM A B C D G H J K N S 3 D 5 PL 0.2 (0.008) M B M N INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC --0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087 MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC --0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20 J C K H SOLDER FOOTPRINT* 0.50 0.0197 0.65 0.025 0.65 0.025 0.40 0.0157 1.9 0.0748 SCALE 20:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 20 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCP715/D