Diodes AH180-PL-A Micropower omnipolar hall-effect sensor Datasheet

AH180
MICROPOWER OMNIPOLAR HALL-EFFECT SENSOR
SWITCH
Description
Pin Assignments
AH180 is a micro-power Omnipolar Hall-Effect switch
designed for portable and battery powered equipment such
cellular phones, PDAs and portable PCs. Based on two HallEffect plates and a chopper stabilized architecture the AH180
provides a reliable solution over the whole operating range.
To support portable and battery powered equipment the
design has been optimized to operate over the supply range
of 2.5V to 5.5V and consumes only 24uW with a supply of 3V.
(Top View)
3. Output
2. GND
1. Vdd
(SIP-3L)
(Top View)
The single open-drain output switches on with either a north
or south pole of sufficient strength.
When the magnetic flux density (B) is larger than operate
point (Bop), output is switched on (Output pin is pulled low).
The output is turned off when B becomes lower than the
release point (Brp). The output will remain off when there is
no magnetic field.
3. Output
GND 2.
1 . Vdd
SC59
6. NC
( Top View )
3. GND
(Top View)
5. GND 4. NC
The AH180 is available in SIP-3L, SC59, DFN2020-3, and
DFN2020-6 packages.
Features
•
•
•
•
•
•
•
•
•
•
Omnipolar (north or south pole) operation
Micropower operation
Single open drain output
2.5V to 5.5V operating voltage
Chopper stabilized design provides
• Superior temperature stability
• Minimal switch-point drift
• Enhanced immunity to stress
Good RF noise immunity
-40°C to 85°C operating temperature
ESD (HBM) > 5KV for DFN2020-6, DFN2020-3
> 6KV for SIP-3L and SC59
SIP-3L, SC59 (commonly known as SOT23 in Asia)
DFN2020-6, DFN2020-3 packages
Green Molding Compound (No Br, Sb) (Note 1)
Notes:
1. Vdd
2. NC
3. Output
1. Vdd
DFN2020-6
3. Output
DFN2020-3
Applications
•
•
•
Cover switch in clam-shell cellular phones
Cover switch in Notebook PC/PDA
Contact-less switch in consumer products
1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at
http://www.diodes.com/products/lead_free.html.
AH180
Document number: DS31023 Rev. 17 - 2
1 of 13
www.diodes.com
July 2010
© Diodes Incorporated
AH180
MICROPOWER OMNIPOLAR HALL-EFFECT SENSOR
SWITCH
Typical Application Circuit
2.5~5.5V
RL
C
Output
AH180
Gnd
Note: C is for power stabilization and to strengthen the noise immunity, the recommended capacitance is 10nF~100nF.
RL is the pull-up resistor, the recommended resistance is 10Kohm~100Kohm.
Pin Descriptions
Pin Name
Vdd
GND
Output
NC
P/I/O
P/I
P/I
O
NC
Description
Power Supply Input
Ground
Output Pin
No Connected
Functional Block Diagram
Vdd
Power
switch
Offset
Cancelling
Hall Plate
Latch
Amp
Output
Logical
GND
AH180
Document number: DS31023 Rev. 17 - 2
Offset
Cancelling
Hall Plate
Latch
Amp
2 of 13
www.diodes.com
July 2010
© Diodes Incorporated
AH180
MICROPOWER OMNIPOLAR HALL-EFFECT SENSOR
SWITCH
Absolute Maximum Ratings (TA = 25°C)
Symbol
Vdd
B
Ts
PD
TJ
Characteristics
Supply voltage
Magnetic flux density
Storage Temperature Range
SIP-3L
Package Power Dissipation
SC59-3L/ DFN2020-6/
DFN2020-3
Maximum Junction Temperature
Values
7
Unlimited
-65 to +150
550
Unit
V
°C
mW
230
mW
150
°C
Recommended Operating Conditions
Symbol
Vdd
TA
Parameter
Supply Voltage
Operating Ambient Temperature
Conditions
Operating
Operating
Min
2.5
-40
Unit
V
°C
Max
5.5
85
Electrical Characteristics (TA = 25 °C, Vdd = 3V; unless otherwise specified)
Symbol
Vout
Ioff
Idd(en)
Characteristic
Output On Voltage
Output Leakage Current
Idd(en)
Idd(dis)
Idd(dis)
Supply Current
Idd(avg)
Idd(avg)
Tawake
Tperiod
D.C.
Notes:
Awake Time
Period
Duty Cycle
Conditions
Iout =1mA
Vout =5.5V, Output off
Chip enable, TA = 25°C, Vdd = 3V
Chip enable, TA = -40~85°C,
Vdd = 2.5~5.5V
Chip disable, TA = 25°C, Vdd = 3V
Chip disable, TA = -40~85°C,
Vdd = 2.5~5.5V
Average supply current,
TA = 25°C, Vdd = 3V
Average supply current,
TA = -40~85°C, Vdd = 2.5~5.5V
(Note 2)
(Note 2)
Min
Typ.
Max
Unit
⎯
⎯
⎯
0.1
<0.1
3
0.3
1
6
V
µA
mA
⎯
3
9
mA
⎯
5
10
µA
⎯
5
15
µA
⎯
8
16
µA
⎯
8
24
µA
⎯
⎯
⎯
75
75
0.1
125
125
⎯
µs
ms
%
2. When power is initially turned on, Vdd must be within its correct operating range (2.5V to 5.5V) to guarantee the output sampling.
The output state is valid after the second operating phase (typical 150ms).
Tperiod
Tawake
Idd(en)
Sample and output
latched
Idd (dis)
0
AH180
Document number: DS31023 Rev. 17 - 2
3 of 13
www.diodes.com
July 2010
© Diodes Incorporated
AH180
MICROPOWER OMNIPOLAR HALL-EFFECT SENSOR
SWITCH
Magnetic Characteristics (TA = 25 °C, Vdd = 3V, Note 3, 4)
Option 1:
(1mT=10 Gauss)
Symbol
Bops(south pole to brand side)
Bopn(north pole to brand side)
Brps(south pole to brand side)
Brpn(north pole to brand side)
Bhy(|Bopx|-|Brpx|)
Parameter
Min
-60
10
-
Operation Point
Release Point
Hysteresis
Typ.
40
-40
30
-30
15
Option 2:
Unit
Gauss
(1mT=10 Gauss)
Symbol
Bops(south pole to brand side)
Bopn(north pole to brand side)
Brps(south pole to brand side)
Brpn(north pole to brand side)
Bhy(|Bopx|-|Brpx|)
Notes:
Max
60
-10
-
Parameter
Min
-60
20
-
Operation Point
Release Point
Hysteresis
Typ.
40
-40
30
-30
15
Max
60
-20
-
Unit
Gauss
3. Typical data is at TA = 25°C, Vdd = 3V, and for design information only.
4. Magnetic characteristics may vary with supply voltage, operating temperature and after soldering.
Operating Characteristics
Vcc ( off-state )
Turn off
Turn on
Bhy
Output
( Output Voltage )
( Output Voltage )
Output
( on-state )
Bopn Brpn 0
( Magnetic flux density B )
Document number: DS31023 Rev. 17 - 2
Turn off
Vcc
Bhy
Turn on
Vsat
Vsat
AH180
( off-state )
( on-state )
0 Brps Bops
( Magnetic flux density B )
4 of 13
www.diodes.com
July 2010
© Diodes Incorporated
AH180
MICROPOWER OMNIPOLAR HALL-EFFECT SENSOR
SWITCH
Performance Characteristics
(1) SIP-3L
TA (°C)
PD (mW)
TA (°C)
PD (mW)
25
550
105
198
50
440
110
176
P D (mW)
60
396
115
154
70
352
120
132
80
308
125
110
85
286
130
88
90
264
135
66
95
242
140
44
100
220
150
0
Power Dissipation Curve
6 00
5 00
4 00
3 00
2 00
1 00
0
0
-40
25
50
75
100
85
1 25
(2) SC59 (commonly known as SOT23 in Asia), DFN2020-6 and DFN2020-3
25
50
60
70
80
85
90
100
110
120
TA (°C)
PD (mW)
230
184
166
147
129
P D (m W )
120
110
92
74
55
15 0
T A (oC)
130
140
150
37
18
0
P o w e r D is s i p a tio n C u rv e
300
200
100
0
-40 0
25
50
75
85
100
12 5
150
o
TA ( C)
AH180
Document number: DS31023 Rev. 17 - 2
5 of 13
www.diodes.com
July 2010
© Diodes Incorporated
AH180
MICROPOWER OMNIPOLAR HALL-EFFECT SENSOR
SWITCH
Ordering Information
AH 180 - XX X - X X
Package
P : SIP-3L
W : SC59
SN : DFN2020-6
FJ : DFN2020-3
Device
AH180-PL-B
Packing
Lead Free
L : Lead Free
G : Green (Note 5, 6)
Bulk
Package Packaging
Part
Code
(Note 7, 8) Quantity Number
Suffix
P
SIP-3L
1000
-B
Magnetic Characteristics
(Note 11)
Blank : Option 1
-S : Option 2
A : Ammo Box (Note 9)
B : Bulk (Note 10)
7 : Tape & Reel
7” Tape and Reel
Ammo Box
Part
Part
Quantity
Number Quantity Number
Suffix
Suffix
NA
NA
NA
NA
Magentic
Characteristics
(Note 11)
Blank
AH180-PL-A
P
SIP-3L
NA
NA
NA
NA
-A
4000/Box
Blank
AH180-PG-B
P
SIP-3L
1000
-B
NA
NA
NA
NA
Blank
AH180-PG-A
P
SIP-3L
NA
NA
NA
NA
-A
4000/Box
Blank
AH180-PL-B-S
P
SIP-3L
1000
-B
NA
NA
NA
NA
S
AH180-PL-A-S
P
SIP-3L
NA
NA
NA
NA
-A
4000/Box
S
AH180-PG-B-S
P
SIP-3L
1000
-B
NA
NA
NA
NA
S
AH180-PG-A-S
P
SIP-3L
NA
NA
NA
NA
-A
4000/Box
S
AH180-WG-7
W
SC59
NA
NA
3000/Tape & Reel
-7
NA
NA
Blank
AH180-SNG-7
SN
DFN2020-6
NA
NA
3000/Tape & Reel
-7
NA
NA
Blank
AH180-FJG-7
FJ
DFN2020-3
NA
NA
3000/Tape & Reel
-7
NA
NA
Blank
Notes:
5. SC59, DFN2020-6 and DFN2020-3 are available in “Green” product only.
6. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at
http://www.diodes.com/products/lead_free.html.
7. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at
http://www.diodes.com/datasheets/ap02001.pdf.
8. Reverse taping as shown on Diodes Inc. Surface Mount (SMD) Packaging document AP02007, which can be found on our website
http://www.diodes.com/datasheets/ap02007.pdf.
9. Ammo Box is for SIP-3L Spread Lead.
10. Bulk is for SIP-3L Straight Lead.
11. Please refer the Magnetic Characteristics table, option 2 is available in SIP-3L package only.
AH180
Document number: DS31023 Rev. 17 - 2
6 of 13
www.diodes.com
July 2010
© Diodes Incorporated
AH180
MICROPOWER OMNIPOLAR HALL-EFFECT SENSOR
SWITCH
Marking Information
(1) SIP-3L
(Top View)
Y : Year : 0~9
WW : Week : 01~52, "52" represents
52 and 53 week
X : Internal Code : A~Z : Green
a~z : Lead Free
180
Part Number
Y WW X
(2) SC59 (commonly known as SOT23 in Asia)
( Top View )
XX Y W X
Part Number
AH180
XX : Identification code
Y : Year 0~9
W : Week : A~Z : 1~26 week;
a~z : 27~52 week; z represents
52 and 53 week
X : A~Z : Green
Package
SC59
Identification Code
K0
(3) DFN2020-6
( Top View )
180
YWX
AH180
Document number: DS31023 Rev. 17 - 2
Pin 1 indicator
Y : Year : 0~9
W : Week : A~Z : 1~26 week;
a~z : 27~52 week; z represents
52 and 53 week
X : A~Z : Green
7 of 13
www.diodes.com
July 2010
© Diodes Incorporated
AH180
MICROPOWER OMNIPOLAR HALL-EFFECT SENSOR
SWITCH
Marking Information (Continued)
(4) DFN2020-3
( Top View )
XX
YWX
Part Number
AH180
AH180
Document number: DS31023 Rev. 17 - 2
Pin 1 indicator
XX : Identification Code
Y : Year : 0~9
W : Week : A~Z : 1~26 week;
a~z : 27~52 week; z represents
52 and 53 week
X : A~Z : Green
Package
DFN2020-3
8 of 13
www.diodes.com
Identification Code
K0
July 2010
© Diodes Incorporated
AH180
MICROPOWER OMNIPOLAR HALL-EFFECT SENSOR
SWITCH
Package Outline Dimensions (All Dimensions in mm)
(1) Package Type: SIP-3L for Bulk pack
0.51mm
NOM
2.00 +/0.10mm
1.15 +/0.10mm
BRANDED
SURFACE
1
Active Area Depth
2
3
Sensor Location
Package Dimension
AH180
Document number: DS31023 Rev. 17 - 2
9 of 13
www.diodes.com
July 2010
© Diodes Incorporated
AH180
MICROPOWER OMNIPOLAR HALL-EFFECT SENSOR
SWITCH
Package Outline Dimensions (Continued)
(2) Package Type: SIP-3L for Ammo pack
(3) SC59 (Commonly known as SOT23 in Asia)
TOP VIEW
1.50/
1.70
0.35/0.50
2.70/
3.00
1.90
2.90/3.10
1.00/
1.30
0.10/0.20
0.013/0.10
0.95
0.35/0.55
0 O /8 O
AH180
Document number: DS31023 Rev. 17 - 2
10 of 13
www.diodes.com
July 2010
© Diodes Incorporated
AH180
MICROPOWER OMNIPOLAR HALL-EFFECT SENSOR
SWITCH
Package Outline Dimensions (Continued)
0.43mon.
0.57/0.63
(4) Package Type: DFN2020-6
Marking
0.05 C
0/0.05
0.15max.
0.15 C
0.08 C
1.95/2.075
Sensor location
A
0.30/0.40
1.45/1.65
0.76/0.96
1.95/2.075
B
R0
2x-
Seating plane
C
2x
Pin#1 ID
(Active area depth)
.1
0.15 C
0.65nom.
0.2/0.3
0.05 M C A B
Bottom View
0.13Max.
0.57/0.63
Typ 0.60
(5) Package Type: DFN2020-3
0.10 C
Seating plane
C
0.35/0.45
Sensor location
R0
.2
C
L
0.25 B
0.10M C A B
0.2/0.3
1.1/1.3
0.325(Ref.)
A
Bottom View
2x
0.25 A
1.95/2.075
0.138(Ref.)
2x-
C
L
0.5Typ
0.8/1.0
1.95/2.075
B
0/0.05
0.08 C
AH180
Document number: DS31023 Rev. 17 - 2
11 of 13
www.diodes.com
July 2010
© Diodes Incorporated
AH180
MICROPOWER OMNIPOLAR HALL-EFFECT SENSOR
SWITCH
Taping Orientation (Note 12)
(1) DFN2020-6
(2) DFN2020-3
Notes:
12. The taping orientation of the other package type can be found on our website at http://www.diodes.com/datasheets/ap02007.pdf.
AH180
Document number: DS31023 Rev. 17 - 2
12 of 13
www.diodes.com
July 2010
© Diodes Incorporated
AH180
MICROPOWER OMNIPOLAR HALL-EFFECT SENSOR
SWITCH
IMPORTANT NOTICE
DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS
DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).
Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other
changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability
arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any
license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described
herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies
whose products are represented on Diodes Incorporated website, harmless against all damages.
Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized
sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall
indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.
Products described herein may be covered by one or more United States, international or foreign patents pending. Product names
and markings noted herein may also be covered by one or more United States, international or foreign trademarks.
LIFE SUPPORT
Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without
the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:
A. Life support devices or systems are devices or systems which:
1. are intended to implant into the body, or
2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided
in the labeling can be reasonably expected to result in significant injury to the user.
B.
A critical component is any component in a life support device or system whose failure to perform can be reasonably expected
to cause the failure of the life support device or to affect its safety or effectiveness.
Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or
systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements
concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems,
notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further,
Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes
Incorporated products in such safety-critical, life support devices or systems.
Copyright © 2010, Diodes Incorporated
www.diodes.com
AH180
Document number: DS31023 Rev. 17 - 2
13 of 13
www.diodes.com
July 2010
© Diodes Incorporated
Similar pages