Datasheet Operational Amplifiers Low Noise Operational Amplifiers BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV ●General Description Normal BA4560 and high-reliability BA4560R / BA4564R/BA4564W integrate two or four independent Op-Amps on a single chip. Especially, this series is suitable for any audio applications due to low noise and low distortion characteristics and there are usable for other many applications by wide operating supply voltage range. BA4560R / BA4564R / BA4564W are high-reliability products with extended operating temperature range and high ESD tolerance. ●Key Specification Wide Operating Supply Voltage (split supply):±4V to ±15V Wide Temperature Range: BA4560 -40°C to +85°C BA4560R/BA4564R/BA4564W -40°C to +105°C High Slew Rate: 4V/µs(typ.) Total Harmonic Distortion: 0.003%(typ.) Input Referred Noise Voltage: 8 nV/ Hz (typ.) Low Offset Voltage: BA4564W 2.5mV(max.) ●Features High voltage gain, low noise, low distortion Wide operating supply voltage Internal ESD protection circuit Wide Operating Temperature Range ●Packages W(Typ.) x D(Typ.) x H(Max.) SOP8 5.00mm x 6.20mm x 1.71mm MSOP8 2.90mm x 4.00mm x 0.90mm SSOP-B8 3.00mm x 6.40mm x 1.35mm TSSOP-B8 3.00mm x 6.40mm x 1.00mm SOP-J8 4.90mm x 6.00mm x 1.65mm SSOP-B14 5.00mm x 6.40mm x 1.35mm ●Selection Guide Maximum Operation Temperature Normal Dual Slew Rate +85°C 4V/µs BA4560F BA4560FJ BA4560FV BA4560FVT BA4560FVM +105°C Slew Rate High Reliability ●Block Diagram Dual 4V/µs Quad 4V/µs BA4560RF BA4560RFJ BA4560RFV BA4560RFVT BA4560RFVM BA4564RFV BA4564WFV VCC －IN VOUT ＋IN VEE Fig. 1 Simplified schematic ○Product structure：Silicon monolithic integrated circuit www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･14･00 ○This product is not designed protection against radioactive rays. 1/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ●Pin Configuration(TOP VIEW) OUT1 1 OUT1 1 -IN1 +IN1 VEE 2 8 VCC 7 OUT2 CH1 - + 3 -IN1 2 6 -IN2 CH2 + - 4 CH1 - + CH4 + - 12 +IN4 VCC 4 11 VEE 5 -IN2 6 10 +IN3 - + CH2 + CH3 OUT2 7 SOP8 SOP- J8 SSOP-B8 T SSOP-B8 13 -IN4 +IN1 3 +IN2 5 +IN2 14 OUT4 9 -IN3 8 OUT3 SSOP-B14 M SOP8 Package SOP8 SSOP-J8 SSOP-B8 TSSOP-B8 MSOP8 SSOP-B14 BA4560F BA4560RF BA4560FJ BA4560RFJ BA4560FV BA4560RFV BA4560FVT BA4560RFVT BA4560FVM BA4560RFVM BA4564RFV BA4564WFV ●Ordering Information B A 4 5 6 x x x x x - Packaging and forming specification E2: Embossed tape and reel (SOP8/SSOP-B8/TSSOP-B8/SOP-J8 SSOP-B14) TR: Embossed tape and reel (MSOP8) Package F : SOP8 FJ : SOP-J8 FV : SSOP-B8 : SSOP-B14 FVM : MSOP8 FVT : TSSOP-B8 Part Number BA4560xxx BA4560Rxxx BA4564RFV BA4560WFV xx ●Line-up Topr Operating Supply Voltage (split supply) Supply Current (Typ.) Offset Voltage (max.) SOP8 -40°C to +85°C 4mA 6mV ±4.0V to ±15.0V 3mA -40°C to +105°C 6mA www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 2.5mV 2/41 Orderable Part Number Package Reel of 2500 BA4560F-E2 SOP-J8 Reel of 2500 BA4560FJ-E2 SSOP-B8 Reel of 2500 BA4560FV-E2 TSSOP-B8 Reel of 2500 BA4560FVT-E2 MSOP8 Reel of 3000 BA4560FVM-TR SOP8 Reel of 2500 BA4560RF-E2 SOP-J8 Reel of 2500 BA4560RFJ-E2 SSOP-B8 Reel of 2500 BA4560RFV-E2 TSSOP-B8 Reel of 3000 BA4560RFVT-E2 MSOP8 Reel of 3000 BA4560RFVM-TR SSOP-B14 Reel of 2500 BA4564RFV-E2 SSOP-B14 Reel of 2500 BA4564WFV-E2 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ●Absolute Maximum Ratings (Ta=25℃) ○BA4560, BA4560R, BA4564R, BA4564W Parameter Ratings Symbol Supply Voltage BA4560 BA4560R VCC-VEE SSOP-B8 TSSOP-B8 MSOP8 SSOP-B14 *7 - - 540 *2*6 675 - - 500*3*6 625*3*6 - - *3*6 500 *3*6 625 - - 470*4*6 587*4*6 - *2*6 - 690 - Unit V *1*6 552 SOP-J8 Pd BA4564W +36 *1*6 SOP8 Power dissipation BA4564R mW *5*6 875 875*5*6 Differential Input Voltage Input Common-mode voltage range Operating Supply Voltage Vid VCC-VEE +36 V Vicm VEE to VCC (VEE-0.3) to VEE+36 V Operating Temperature Topr -40 to +85 -40 to +105 ℃ Storage Temperature Tstg -55 to +125 -55 to +150 ℃ Tjmax +125 +150 ℃ Maximum junction Temperature Vopr +8 to +30 (±4 to ±15) V Note: Absolute maximum rating item indicates the condition which must not be exceeded. Application of voltage in excess of absolute maximum rating or use out absolute maximum rated temperature environment may cause deterioration of characteristics. *1 To use at temperature above Ta＝25℃ reduce 5.52mW. *2 To use at temperature above Ta＝25℃ reduce 5.4mW. *3 To use at temperature above Ta＝25℃ reduce 5mW. *4 To use at temperature above Ta＝25℃ reduce 4.7mW. *5 To use at temperature above Ta＝25℃ reduce 7mW. *6 Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm). *7 The voltage difference between inverting input and non-inverting input is the differential input voltage. Then input terminal voltage is set to more than VEE. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 3/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ●Electrical Characteristics ○BA4560 (Unless otherwise specified VCC=+15V, VEE=-15V) Parameter Symbol Temperature Range Min. Limits Typ. Max. Unit Condition Input Offset Voltage *8 Vio 25℃ - 0.5 6 mV VOUT=0V Input Offset Current *8 Iio 25℃ - 5 200 nA VOUT=0V Input Bias Current *9 Ib 25℃ - 50 500 nA VOUT=0V Supply Current ICC 25℃ - 4 7.5 mA RL=∞, All Op-Amps, VIN+=0V Maximum Output Voltage VOM 25℃ ±12 ±14 - 25℃ ±10 ±13 - Large Signal Voltage Gain AV 25℃ 86 100 - dB RL≧2kΩ, VO=±10V Vicm=0V Vicm 25℃ ±12 ±14 - V VOUT=±12V Common-mode Rejection Ratio CMRR 25℃ 70 90 - dB VOUT=±12V Power Supply Rejection Ratio PSRR 25℃ 76.3 90 - dB Ri≦10kΩ SR 25℃ - 4 - V/μs AV=0dB, RL=2kΩ Unity Gain Frequency ft 25℃ - 4 - MHz RL=2kΩ Unity Gain Frequency GBW 25℃ - 10 - MHz f=10kHz THD+N 25℃ - 0.003 - % - 8 - nV/ Hz RS=100Ω, Vi=0V f=1kHz - - 2.2 μVrms RS=2.2Ω, RIAA BW=10kHz to 30kHz Input Common-mode Voltage Range Slew Rate Total Harmonic Distortion Input Referred Noise Voltage *8 *9 Vn RL≧10kΩ V RL≧2kΩ AV=20dB, RL=10kΩ VIN=0.05Vrms, f=1kHz 25℃ Absolute value Current direction: Since first input stage is composed with PNP transistor, input bias current flows out of IC. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 4/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ○BA4560R (Unless otherwise specified VCC=+15V, VEE=-15V, Full range -40℃ to +105℃) Limits Temperature Parameter Symbol Unit Range Min. Typ. Max. Input Offset Voltage *10 Vio Input Offset Current *10 Iio Input Bias Current *11 Ib Supply Current ICC Maximum Output Voltage VOM Large Signal Voltage Gain Input Common-mode Voltage Range AV Vicm 25℃ - 0.5 6 Full range - - 7 25℃ - 5 200 Full range - - 200 25℃ - 50 500 Full range - - 800 25℃ - 3 7 Full range - - 7.5 25℃ ±12 ±14 - Full range ±10 ±11.5 - 25℃ 86 100 - Full range 83 - - 25℃ ±12 ±14 - Full range ±12 - - Condition mV VOUT=0V nA VOUT=0V nA VOUT=0V mA RL=∞, All Op-Amps VIN+=0V RL≧2kΩ V Io=25mA dB RL≧2kΩ, VO=±10V Vicm=0V V VOUT=±12V Common-mode Rejection Ratio CMRR 25℃ 70 90 - dB VOUT=±12V Power Supply Rejection Ratio PSRR 25℃ 76.5 90 - dB Ri≦10kΩ Channel Separation CS 25℃ - 105 - dB R1=100Ω,f=1kHz Slew Rate SR 25℃ - 4 - V/μs ft 25℃ - 4 - MHz RL=2kΩ THD+N 25℃ - 0.003 - % - 8 - nV/ Hz - 1.0 - μVrms DIN-AUDIO Unity Gain Frequency Total Harmonic Distortion Input Referred Noise Voltage *10 *11 Vn AV=0dB, RL=10kΩ CL=100pF AV=20dB, RL=10kΩ VIN=0.05Vrms, f=1kHz RS=100Ω, Vi=0V f=1kHz 25℃ Absolute value Current direction: Since first input stage is composed with PNP transistor, input bias current flows out of IC. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 5/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ○BA4564R (Unless otherwise specified VCC=+15V, VEE=-15V, Full range -40℃ to +105℃) Limits Temperature Parameter Symbol Unit Range Min. Typ. Max. Input Offset Voltage *12 Vio Input Offset Current *12 Iio Input Bias Current *13 Ib Supply Current ICC Maximum Output Voltage VOM Large Signal Voltage Gain Input Common-mode Voltage Range AV Vicm 25℃ - 0.5 6 Full range - - 7 25℃ - 5 200 Full range - - 200 25℃ - 50 500 Full range - - 800 25℃ - 6 14 Full range - - 15 25℃ ±12 ±14 - Full range ±10 ±11.5 - 25℃ 86 100 - Full range 83 - - 25℃ ±12 ±14 - Full range ±12 - - Condition mV VOUT=0V nA VOUT=0V nA VOUT=0V mA RL=∞, All Op-Amps VIN+=0V RL≧2kΩ V Io=25mA dB RL≧2kΩ, VOUT=±10V Vicm=0V V VOUT=±12V Common-mode Rejection Ratio CMRR 25℃ 70 90 - dB VOUT=±12V Power Supply Rejection Ratio PSRR 25℃ 76.5 90 - dB Ri≦10kΩ Channel Separation CS 25℃ - 105 - dB R1=100Ω, f=1kHz Slew Rate SR 25℃ - 4 - V/μs AV=0dB, RL=10kΩ CL=100pF ft 25℃ - 4 - MHz RL=2kΩ THD+N 25℃ - 0.003 - % - 8 - nV/ Hz - 1.0 - μVrms DIN-AUDIO Unity Gain Frequency Total Harmonic Distortion Input Referred Noise Voltage *12 *13 Vn AV=20dB, RL=10kΩ VIN=0.05Vrms, f=1kHz RS=100Ω, Vi=0V f=1kHz 25℃ Absolute value Current direction: Since first input stage is composed with PNP transistor, input bias current flows out of IC. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 6/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ○BA4564W (Unless otherwise specified VCC=+15V, VEE=-15V, Full range -40℃ to +105℃) Limits Temperature Parameter Symbol BA4564WFV Unit Range Min. Typ. Max. Input Offset Voltage *14 Vio Input Offset Current *14 Iio Input Bias Current *15 Ib Supply Current ICC Maximum Output Voltage VOM Large Signal Voltage Gain AV Input Common-mode Voltage Range Vicm 25℃ - 0.5 2.5 Full range - - 4 25℃ - 5 200 Full range - - 200 25℃ - 50 300 Full range - - 500 25℃ - 6 11 Full range - - 13 25℃ ±12 ±14 - Full range ±10 ±11.5 - 25℃ 86 100 - Full range 83 - - 25℃ ±12 ±14 - Full range ±12 - - Condition mV VOUT=0V nA VOUT=0V nA VOUT=0V mA RL=∞, All Op-Amps VIN+=0V RL≧2kΩ V Io=25mA dB RL≧2kΩ, VOUT=±10V Vicm=0V V VOUT=±12V Common-mode Rejection Ratio CMRR 25℃ 70 90 - dB VOUT=±12V Power Supply Rejection Ratio PSRR 25℃ 76.5 90 - dB Ri≦10kΩ Channel Separation CS 25℃ - 105 - dB R1=100Ω, f=1kHz Slew Rate SR 25℃ - 4 - V/μs AV=0dB, RL=10kΩ CL=100pF ft 25℃ - 4 - MHz RL=2kΩ THD+N 25℃ - 0.003 - % - 8 - nV/ Hz - 1.0 - μVrms DIN-AUDIO Unity Gain Frequency Total Harmonic Distortion Input Referred Noise Voltage *14 *15 Vn AV=20dB, RL=10kΩ VIN=0.05Vrms, f=1kHz RS=100Ω, Vi=0V f=1kHz 25℃ Absolute value Current direction: Since first input stage is composed with PNP transistor, input bias current flows out of IC. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 7/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet Description of electrical characteristics Described here are the terms of electric characteristics used in this datasheet. Items and symbols used are also shown. Note that item name and symbol and their meaning may differ from those on another manufacture’s document or general document. 1. Absolute maximum ratings Absolute maximum rating item indicates the condition which must not be exceeded. Application of voltage in excess of absolute maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of characteristics. 1.1 Power supply voltage (VCC-VEE) Indicates the maximum voltage that can be applied between the positive power supply terminal and negative power supply terminal without deterioration or destruction of characteristics of internal circuit. 1.2 Differential input voltage (Vid) Indicates the maximum voltage that can be applied between non-inverting terminal and inverting terminal without deterioration and destruction of characteristics of IC. 1.3 Input common-mode voltage range (Vicm) Indicates the maximum voltage that can be applied to non-inverting terminal and inverting terminal without deterioration or destruction of characteristics. Input common-mode voltage range of the maximum ratings not assure normal operation of IC. When normal operation of IC is desired, the input common-mode voltage of characteristics item must be followed. 1.4 Power dissipation (Pd) Indicates the power that can be consumed by specified mounted board at the ambient temperature 25℃(normal temperature). As for package product, Pd is determined by the temperature that can be permitted by IC chip in the package (maximum junction temperature)and thermal resistance of the package. 2. Electrical characteristics item 2.1 Input offset voltage (Vio) Indicates the voltage difference between non-inverting terminal and inverting terminal. It can be translated into the input voltage difference required for setting the output voltage at 0 V . 2.2 Input offset current (Iio) Indicates the difference of input bias current between non-inverting terminal and inverting terminal. 2.3 Input bias current (Ib) Indicates the current that flows into or out of the input terminal. It is defined by the average of input bias current at non-inverting terminal and input bias current at inverting terminal. 2.4 Input common-mode voltage range(Vicm) Indicates the input voltage range where IC operates normally. 2.5 Large signal voltage gain (AV) Indicates the amplifying rate (gain) of output voltage against the voltage difference between non-inverting terminal and Inverting terminal. It is normally the amplifying rate (gain) with reference to DC voltage. Av = (Output voltage fluctuation) / (Input offset fluctuation) 2.6 Circuit current (ICC) Indicates the IC current that flows under specified conditions and no-load steady status. 2.7 Output saturation voltage (VOM) Signifies the voltage range that can be output under specific output conditions. 2.8 Common-mode rejection ratio (CMRR) Indicates the ratio of fluctuation of input offset voltage when in-phase input voltage is changed. It is normally the fluctuation of DC. CMRR = (Change of Input common-mode voltage) / (Input offset fluctuation) 2.9 Power supply rejection ratio (PSRR) Indicates the ratio of fluctuation of input offset voltage when supply voltage is changed. It is normally the fluctuation of DC. PSRR = (Change of power supply voltage) / (Input offset fluctuation) 2.10 Unity gain frequency (ft) Indicates a frequency where the voltage gain of operational amplifier is 1. 2.11 Slew Rate (SR) SR is a parameter that shows movement speed of operational amplifier. It indicates rate of variable output voltage as unit time. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 8/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet 2.12 Gain Band Width (GBW) Indicates to multiply by the frequency and the gain where the voltage gain decreases 6dB/octave. 2.13 Total harmonic distortion + Noise (THD+N) Indicates the fluctuation of input offset voltage or that of output voltage with reference to the change of output voltage of driven channel. 2.14 Input referred noise voltage (Vn) Indicates a noise voltage generated inside the operational amplifier equivalent by ideal voltage source connected in series with input terminal. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 9/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ●Typical Performance Curves ○BA4560 8.0 800 SUPPLY CURRENT [mA] POWER DISSIPATION [mW] . . 1000 BA4560F BA4560FJ 600 BA4560FV/FVT BA4560FVM 400 200 -40℃ 6.0 25℃ 4.0 85℃ 2.0 0.0 0 0 25 50 75 100 AMBIENT TEMPERTURE [ ℃] . 0 125 Fig.2 Derating Curve MAXIMUM OUTPUT VOLTAGE SWING [VP-P] SUPPLY CURRENT [mA] 6.0 ±15V 4.0 ±4 V 2.0 0.0 -50 -25 0 25 50 75 AMBIENT TEMPERATURE [℃] 10 15 20 25 SUPPLY VOLTAGE [V] 30 35 Fig.3 Supply Current - Supply Voltage 8.0 ±7.5 V 5 100 30 25 20 15 10 5 0 0.1 Fig.4 Supply Current - Ambient Temperature 1 LOAD RESISTANCE [kΩ] 10 Fig.5 Maximum Output Voltage Swing - Load Resistance (VCC/VEE=+15V/-15V,Ta=25℃) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 10/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ○BA4560 20 20 15 15 10 10 OUTPUT VOLTAGE [V] OUTPUT VOLTAGE [V] VOH VOH 5 0 -5 VOL -10 5 0 -5 -10 VOL -15 -15 -20 0.1 -20 1 10 ±2 ±4 ±6 ±8 ±10 ±12 ±14 ±16 ±18 SUPPLY VOLTAGE [V] LOAD RESISTANCE [kΩ] Fig.7 Maximum Output Voltage - Supply Voltage (RL=2kΩ,Ta=25℃) 20 20 15 15 10 OUTPUT VOLTAGE [V] OUTPUT VOLTAGE [V] Fig.6 Maximum Output Voltage - Load Resistance (VCC/VEE=+15V/-15V,Ta=25℃) VOH 5 0 -5 VOL -10 -15 -20 -50 10 VOH 5 0 -5 VOL -10 -15 -20 -25 0 25 50 75 100 0 AMBIENT TEMPERATURE [℃] 5 10 15 20 25 OUTPUT CURRENT [mA] Fig.9 Maximum Output Voltage - Output Current (VCC/VEE=+15V/-15V,Ta=25℃) Fig.8 Maximum Output Voltage - Ambient Temperature (VCC/VEE=+15V/-15V, RL=2kΩ) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 11/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ○BA4560 6 4 -40℃ INPUT OFFSET VOLTAGE [mV] INPUT OFFSET VOLTAGE [mV] 6 25℃ 2 0 -2 85℃ -4 -6 4 ±4V ±7.5V 2 0 ±15V -2 -4 -6 ±2 ±4 ±6 ±8 ±10 ±12 ±14 ±16 -50 -25 0 25 50 75 100 SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [℃] Fig.10 Input Offset Voltage - Supply Voltage (Vicm=0V, Vout=0V) Fig.11 Input Offset Voltage - Ambient Temperature (Vicm=0V, Vout=0V) 60 . 80 INPUT BIAS CURRENT [nA] INPUT BIAS CURRENT [nA] 70 60 -40℃ 50 25℃ 40 30 20 85℃ 10 50 ±4V 40 30 ±7.5V ±15V 20 10 0 0 ±0 ±2 ±4 ±6 ±8 -50 ±10 ±12 ±14 ±16 -25 0 25 50 75 100 AMBIENT TEMPERATURE [℃] SUPPLY VOLTAGE [V] Fig.12 Input Bias Current - Supply Voltage (Vicm=0V, Vout=0V) Fig.13 Input Bias Current - Ambient Temperature (Vicm=0V, Vout=0V) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 12/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet 20 30 INPUT OFFSET CURRENT [nA] . 30 INPUT O FFSET CURRENT [nA] ○BA4560 -40℃ 10 25℃ 0 -10 85℃ -20 20 10 ±4V 0 ±0 -20 ±2 -50 ±4 ±6 ±8 ±10 ±12 ±14 ±16 SUPPLY VO LTAG E [ V] COMMON MODE REJECTION RATIO [dB] 4 85℃ 3 25℃ 1 -40℃ 0 25 50 75 100 Fig.15 Input Offset Current - Ambient Temperature (Vicm=0V, Vout=0V) 5 2 -25 AMBIENT TEMPERATURE [°C] Fig.14 Input Offset Current - Supply Voltage (Vicm=0V, Vout=0V) INPUT OFFSET VOLTAGE [mV] ±15V -10 -30 -30 0 -1 -2 -3 -4 -5 0 ±7.5V 150 125 100 75 50 25 0 -50 2 4 6 8 COMMON MODE INPUT VOLTAGE [V] -25 0 25 50 75 AMBIENT TEMPERATURE [°C] 100 Fig.17 Common Mode Rejection Ratio - Ambient Temperature (VCC/VEE=+15V/-15V, Vicm=-12V to +12V) Fig.16 Input Offset Voltage -Common Mode Input Voltage (VCC=8V, Vout=4V) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 13/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet . ○BA4560 . 6 5 125 SLEW RATE [V/µs] POWER SUPPLY REJECTION RATIO [dB] 150 100 75 50 4 3 2 25 1 0 0 -50 -25 0 25 50 75 ±2 100 ±4 AMBIENT TEMPERATURE [℃] ±14 ±16 Fig.19 Slew Rate - Supply Voltage (CL=100pF, RL=2kΩ, Ta=25℃) Fig.18 Power Supply Rejection Ratio - Ambient Temperature (VCC/VEE=+4V/-4V to +15V/-15V) 1 TOTAL HARMONIC DISTORTION [%] 80 INPUT REFERRED NOISE VOLTAGE [nV/√Hz] ±6 ±8 ±10 ±12 SUPPLY VOLTAGE [V] 60 40 20 0 1 10 100 1000 10000 0.1 20kHz 0.01 1kHz 0.001 20Hz 0.0001 0.1 FREQUENCY [Hz] Fig.20 Equivalent Input Noise Voltage - Frequency (VCC/VEE=+15V/-15V, RS=100Ω, Ta=25℃) 1 OUTPUT VOLTAGE [Vrms] 10 Fig.21 Total Harmonic Distortion - Output Voltage (VCC/VEE=+15V/-15V, AV=20dB, RL=2kΩ, 80kHz-LPF, Ta=25℃) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 14/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet 200 50 180 PHASE 25 20 15 10 160 40 140 30 120 GAIN . 100 80 20 60 10 5 PHASE [deg] 30 VOLTAGE G AIN[dB] MAXIMUM OUTPUT VOLTAGE SWING [VP-P] ○BA4560 40 20 0 0 13 10 5 104 100 10 10 FREQUENCY [KHz] 0 2 3 4 5 6 7 10 10 10 10 10 10 1.E+02 1.E+03 1.E+04 1.E+05 1.E+06 1.E+07 SUPPLY VOLTAGE [V] 1000 106 Fig.22 Maximum Output Voltage Swing – Frequency (VCC/VEE=+15V/-15V, RL=2kΩ, Ta=25℃) Fig.23 Voltage Gain - Frequency (VCC/VEE=+15V/-15V, AV=40dB, RL=2kΩ, Ta=25℃) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 15/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ○BA4560R . 5.0 -40℃ 800 SUPPLY CURRENT [mA] POWER DISSIPATION [mW] . 1000 BA4560RF BA4560RFJ BA4560RFV/FVT 600 BA4560RFVM 400 200 3.0 2.0 105℃ 1.0 0.0 0 0 25 50 75 100 AMBIENT TEMPERTURE [℃] . 0 125 MAXIMUM OUTPUT VOLTAGE SWING [VP-P] ±15V 4.0 3.0 ±4 V ±7.5 V 1.0 0.0 -50 -25 0 25 50 75 100 AMBIENT TEMPERATURE [℃] 10 15 20 25 30 35 Fig.25 Supply Current - Supply Voltage 5.0 2.0 5 SUPPLY VOLTAGE [V] Fig.24 Derating Curve SUPPLY CURRENT [mA] 25℃ 4.0 125 30 25 20 15 10 5 0 0.1 1 10 LOAD RESISTANCE [kΩ] Fig.27 Maximum Output Voltage Swing - Load Resistance (VCC/VEE=+15V/-15V, Ta=25℃) Fig.26 Supply Current - Ambient Temperature (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 16/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ○BA4560R 20 20 15 15 10 10 OUTPUT VOLTAGE [V] OUTPUT VOLTAGE [V] VOH VOH 5 0 -5 VOL -10 5 0 -5 -10 VOL -15 -15 -20 0.1 -20 1 LOAD RESISTANCE [kΩ] 10 ±4 ±6 ±8 ±10 ±12 ±14 SUPPLY VOLTAGE [V] Fig.29 Maximum Output Voltage - Supply Voltage (RL=2kΩ, Ta=25℃) 20 20 15 15 10 OUTPUT VOLTAGE [V] OUTPUT VOLTAGE [V] Fig.28 Maximum Output Voltage - Load Resistance (VCC/VEE=+15V/-15V, Ta=25℃) VOH 5 0 -5 VOL -10 10 VOH 5 0 -5 -15 -20 -50 -20 0 25 50 75 100 VOL -10 -15 -25 ±16 0 125 AMBIENT TEMPERATURE [℃] 5 10 15 20 25 OUTPUT CURRENT [mA] Fig.31 Maximum Output Voltage - Output Current (VCC/VEE=+15V/-15V, Ta=25℃) Fig.30 Maximum Output Voltage - Ambient Temperature (VCC/VEE=+15V/-15V, RL=2kΩ) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 17/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet 6 6 4 4 2 INPUT OFFSET VOLTAGE [mV] INPUT OFFSET VOLTAGE [mV] ○BA4560R -40℃ 25℃ 0 105℃ -2 -4 ±4V 2 ±7.5V 0 -2 ±15V -4 -6 -6 ±2 ±4 ±6 ±8 ±10 ±12 ±14 -50 ±16 0 25 50 75 100 125 AMBIENT TEMPERATURE [℃] SUPPLY VOLTAGE [V] Fig.33 Input Offset Voltage - Ambient Temperature (Vicm=0V, Vout=0V) Fig.32 Input Offset Voltage - Supply Voltage (Vicm=0V, Vout=0V) . . 200 180 200 180 INPUT BIAS CURRENT [nA] INPUT BIAS CURRENT [nA] -25 160 140 120 25℃ 100 -40℃ 80 60 40 105℃ 160 140 120 ±4V ±7.5V 100 80 60 40 ±15V 20 20 0 0 ±2 ±4 ±6 ±8 ±10 ±12 ±14 ±2 ±16 ±4 ±6 ±8 ±10 ±12 ±14 ±16 SUPPLY VOLTAGE [V] SUPPLY VOLTAGE [V] Fig.35 Input Bias Current - Ambient Temperature (Vicm=0V, Vout=0V) Fig.34 Input Bias Current - Supply Voltage (Vicm=0V, Vout=0V) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 18/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet . ○BA4560R 60 INPUT OFFSET CURRENT [nA] INPUT OFFSET CURRENT [nA] 60 40 -40℃ 105℃ 20 0 -20 25℃ -40 40 ±4V 20 ±15V 0 ±7.5V -20 -40 -60 -60 ±0 ±2 -50 ±4 ±6 ±8 ±10 ±12 ±14 ±16 SUPPLY VOLTAGE [V] Fig.36 Input Offset Current - Supply Voltage (Vicm=0V, Vout=0V) COMMON MODE REJECTION RATIO [dB] INPUT OFFSET VOLTAGE [mV] 4 3 2 1 0 -40℃ -2 25℃ -3 105℃ -4 -5 0 125 Fig.37 Input Offset Current - Ambient Temperature (Vicm=0V, Vout=0V) 5 -1 -25 0 25 50 75 100 AMBIENT TEMPERATURE [°C] 150 125 100 75 50 25 0 -50 2 4 6 8 COMMON MODE INPUT VOLTAGE [V] -25 0 25 50 75 100 AMBIENT TEMPERATURE [°C] 125 Fig.39 Common Mode Rejection Ratio - Ambient Temperature (VCC/VEE=+15V/-15V, Vicm=-12V to +12V) Fig.38 Input Offset Voltage -Common Mode Input Voltage (VCC=8V, Vout=4V) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 19/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet 5.0 . 150 125 4.0 SLEW RATE [V/µs] POWER SUPPLY REJECTION RATIO [dB] . ○BA4560R 100 75 50 3.0 2.0 1.0 25 0 0.0 -50 -25 0 25 50 75 100 AMBIENT TEMPERATURE [℃] 125 ±2 ±6 ±8 ±10 ±12 SUPPLY VOLTAGE [V] ±14 ±16 Fig.41 Slew Rate - Supply Voltage (CL=100pF, RL=2kΩ, Ta=25℃) Fig.40 Power Supply Rejection Ratio - Ambient Temperature (VCC/VEE=+4V/-4V to +15V/-15V) 1 TOTAL HARMONIC DISTORTION [%] 80 INPUT REFERRED NOISE VOLTAGE [nV/√Hz] . ±4 60 40 20 10 100 1000 0.01 1kHz 0.001 20Hz 0.0001 0.1 0 1 20kHz 0.1 10000 FREQUENCY [Hz] 1 OUTPUT VOLTAGE [Vrms] 10 Fig.43 Total Harmonic Distortion - Output Voltage (VCC/VEE=+15V/-15V, AV=20dB, RL=2kΩ, 80kHz-LPF, Ta=25℃) Fig.42 Equivalent Input Noise Voltage - Frequency (VCC/VEE=+15V/-15V, RS=100Ω, Ta=25℃) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 20/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet 30 60 25 50 0 -30 20 15 10 5 0 10 10 2 100 10 3 1000 4 10000 5 100000 10 10 10 FREQUENCY [Hz] 40 30 -60 -90 GAIN 20 -120 10 -150 0 -180 PHASE [deg] PHASE VOLTAGE GAIN [dB] MAXIMUM OUTPUT VOLTAGE SWING [VP-P] ○BA4560R 1.E+02 1.E+04 1.E+06 1.E+07 103 104 1.E+05 105 106 107 102 1.E+03 6 1000000 10 FREQ UENCY [Hz] Fig.45 Voltage Gain - Frequency (VCC/VEE=+15V/-15V, AV=40dB, RL=2kΩ, Ta=25℃) Fig.44 Maximum Output Voltage Swing - Frequency (VCC/VEE=+15V/-15V, RL=2kΩ, Ta=25℃) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 21/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ○BA4564R 12.0 . . 1000 SUPPLY CURRENT [mA] PO WER DISSIPATION [mW] 800 BA4564RFV 600 400 200 10.0 -40℃ 8.0 25℃ 6.0 4.0 105℃ 2.0 0 0.0 0 25 50 75 100 AMBIENT TEMPERATURE [℃] 125 0 MAXIMUM OUTPUT VOLTAGE SWING [VP-P] SUPPLY CURRENT [mA] 10.0 ±15V 6.0 ±4V ±7.5V 2.0 0.0 -50 -25 0 25 50 75 100 AMBIENT TEMPERATURE [℃] 15 20 25 30 35 Fig.47 Supply Current - Supply Voltage 12.0 4.0 10 SUPPLY VOLTAGE [V] Fig.46 Derating Curve 8.0 5 125 30 25 20 15 10 5 0 0.1 1 10 LOAD RESISTANCE [kΩ] Fig.49 Maximum Output Voltage Swing - Load Resistance (VCC/VEE=+15V/-15V, Ta=25℃) Fig.48 Supply Current - Ambient Temperature (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 22/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ○BA4564R 20 20 15 15 10 OUTPUT VOLTAGE [V] OUTPUT VOLTAGE [V] VOH VOH 5 0 -5 VOL -10 10 5 0 -5 -10 VOL -15 -15 -20 0.1 -20 1 ±4 10 ±6 ±8 ±10 ±12 ±14 SUPPLY VOLTAGE [V] LOAD RESISTANCE [kΩ] Fig.51 Maximum Output Voltage -Supply Voltage (RL=2kΩ, Ta=25℃) 20 20 15 15 10 OUTPUT VOLTAGE [V] OUTPUT VOLTAGE [V] Fig.50 Maximum Output Voltage -Load Resistance (VCC/VEE=+15V/-15V, Ta=25℃) VOH 5 0 -5 VOL -10 -15 -20 -50 ±16 10 VOH 5 0 -5 VOL -10 -15 -20 -25 0 25 50 75 100 125 0 AMBIENT TEMPERATURE [℃] 5 10 15 20 25 OUTPUT CURRENT [mA] Fig.52 Maximum Output Voltage - Ambient Temperature (VCC/VEE=+15V/-15V, RL=2kΩ) Fig.53 Maximum Output Voltage - Output Current (VCC/VEE=+15V/-15V,Ta=25℃) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 23/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet 6 6 4 4 INPUT OFFSET VOLTAGE [mV] INPUT OFFSET VOLTAGE [mV] ○BA4564R -40℃ 25℃ 2 0 105℃ -2 -4 ±4V ±7.5V 2 0 ±15V -2 -4 -6 -6 ±2 ±4 ±6 ±8 ±10 ±12 ±14 -50 ±16 -25 0 25 50 75 100 125 SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [℃] Fig.54 Input Offset Voltage - Supply Voltage (Vicm=0V, Vout=0V) Fig.55 Input Offset Voltage - Ambient Temperature (Vicm=0V, Vout=0V) 200 180 180 160 160 INPUT BIAS CURRENT [nA] INPUT BIAS CURRENT [nA] . 200 140 -40℃ 25℃ 120 100 80 60 105℃ 40 20 140 ±7.5V ±4V 120 100 80 60 ±15V 40 20 0 0 ±2 ±4 ±6 ±8 ±10 ±12 ±14 ±16 -50 -25 SUPPLY VOLTAGE [V] 0 25 50 75 100 125 AMBIENT TEMPERATURE [℃] Fig.56 Input Bias Current - Supply Voltage (Vicm=0V, Vout=0V) Fig.57 Input Bias Current - Ambient Temperature (Vicm=0V, Vout=0V) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 24/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ○BA4564R 60 INPUT OFFSET CURRENT [nA] INPUT OFFSET CURRENT [nA] 60 40 -40℃ 20 105℃ 0 -20 25℃ -40 40 ±15V 0 ±7.5V -20 -40 -60 -60 ±0 ±2 -50 ±4 ±6 ±8 ±10 ±12 ±14 ±16 SUPPLY VOLTAGE [V] COMMON MODE REJECTION RATIO [dB] 5 4 -40℃ 3 25℃ 2 105℃ 1 0 -1 -2 -3 -4 -5 0 -25 0 25 50 75 100 AMBIENT TEMPERATURE [°C] 125 Fig.59 Input Offset Current - Ambient Temperature (Vicm=0V, Vout=0V) Fig.58 Input Offset Current - Supply Voltage (Vicm=0V, Vout=0V) INPUT OFFSET VOLTAGE [mV] ±4V 20 150 125 100 75 50 25 0 -50 2 4 6 8 COMMON MODE INPUT VOLTAGE [V] -25 0 25 50 75 100 AMBIENT TEMPERATURE [°C] 125 Fig.61 Common Mode Rejection Ratio - Ambient Temperature (VCC/VEE=+15V/-15V, Vicm=-12V to +12V) Fig.60 Input Offset Voltage - Common Mode Input Voltage (VCC=8V, Vout=4V) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 25/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet 150 . 5.0 125 4.0 SLEW RATE [V/µs] POWER SUPPLY REJECTION RATIO [dB] . ○BA4564R 100 75 50 3.0 2.0 1.0 25 0 0.0 -50 -25 0 25 50 75 100 AMBIENT TEMPERATURE [℃] 125 ±2 ±6 ±8 ±10 ±12 SUPPLY VOLTAGE [V] ±14 ±16 Fig.63 Slew Rate - Supply Voltage (CL=100pF, RL=2kΩ, Ta=25℃) Fig.62 Power Supply Rejection Ratio - Ambient Temperature (VCC/VEE=+4V/-4V to +15V/-15V) 80 1 TOTAL HARMONIC DISTORTION [%] INPUT REFERRED NOISE VOLTAGE [nV/√Hz] . ±4 60 40 20 10 100 1000 FREQUENCY [Hz] 20kHz 1kHz 0.01 0.001 20Hz 0.0001 0.1 0 1 0.1 10000 Fig.64 Equivalent Input Noise Voltage - Frequency (VCC/VEE=+15V/-15V, RS=100Ω, Ta=25℃) 1 OUTPUT VOLTAGE [Vrms] 10 Fig.65 Total Harmonic Distortion - Output Voltage (VCC/VEE=+15V/-15V, AV=20dB, RL=2kΩ, 80kHz-LPF, Ta=25℃) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 26/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet 60 25 50 20 15 10 -200 PHASE -170 -140 40 -110 30 GAIN -80 20 PHASE [deg] 30 VO LTAGE GAIN [dB] MAXIMUM OUTPUT VOLTAGE SWING [VP-P] ○BA4564R -50 10 5 -20 0 1.E+01 1.E+02 1.E+03 1.E+04 1.E+05 1.E+06 10 102 103 104 105 106 FREQUENCY [Hz] Fig.66 Maximum Output Voltage Swing – Frequency (VCC/VEE=+15V/-15V, RL=2kΩ, Ta=25℃) 0 2 3 4 5 6 7 10 10 10 10 10 10 1.E+02 1.E+03 1.E+04 1.E+05 1.E+06 1.E+07 FREQUENCY [Hz] Fig.67 Voltage Gain - Frequency (VCC/VEE=+15V/-15V, AV=40dB, RL=2kΩ, Ta=25℃) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 27/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ○BA4564W 12.0 800 SUPPLY CURRENT [mA] POWER DISSIPATION [mW] . . 1000 BA4564WFV 600 400 200 10.0 -40℃ 8.0 25℃ 6.0 4.0 105℃ 2.0 0 0.0 0 25 50 75 100 AMBIENT TEMPERATURE [℃] 125 0 Fig.68 Derating Curve MAXIMUM OUTPUT VOLTAGE SWING [VP-P] SUPPLY CURRENT [mA] 10.0 ±15V 6.0 ±4V 4.0 ±7.5V 2.0 0.0 -50 -25 0 25 50 75 100 AMBIENT TEMPERATURE [℃] 10 15 20 25 SUPPLY VOLTAGE [V] 30 35 Fig.69 Supply Current - Supply Voltage 12.0 8.0 5 125 30 25 20 15 10 5 0 0.1 1 10 LOAD RESISTANCE [kΩ] Fig.71 Maximum Output Voltage Swing - Load Resistance (VCC/VEE=+15V/-15V, Ta=25℃) Fig.70 Supply Current - Ambient Temperature (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 28/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ○BA4564W 20 20 15 15 10 OUTPUT VOLTAGE [V] OUTPUT VOLTAGE [V] VOH VOH 5 0 -5 VOL -10 10 5 0 -5 -10 VOL -15 -15 -20 0.1 -20 1 LOAD RESISTANCE [kΩ] 10 ±4 ±6 ±8 ±10 ±12 ±14 SUPPLY VOLTAGE [V] Fig.73 Maximum Output Voltage -Supply Voltage (RL=2kΩ, Ta=25℃) 20 20 15 15 10 OUTPUT VOLTAGE [V] OUTPUT VOLTAGE [V] Fig.72 Maximum Output Voltage -Load Resistance (VCC/VEE=+15V/-15V, Ta=25℃) VOH 5 0 -5 VOL -10 -15 -20 -50 ±16 10 VOH 5 0 -5 VOL -10 -15 -20 -25 0 25 50 75 100 125 0 AMBIENT TEMPERATURE [℃] 5 10 15 20 25 OUTPUT CURRENT [mA] Fig.74 Maximum Output Voltage - Ambient Temperature (VCC/VEE=+15V/-15V, RL=2kΩ) Fig.75 Maximum Output Voltage - Output Current (VCC/VEE=+15V/-15V, Ta=25℃) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 29/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet 6 6 4 4 INPUT OFFSET VOLTAGE [mV] INPUT OFFSET VOLTAGE [mV] ○BA4564W -40℃ 25℃ 2 0 105℃ -2 -4 ±4V ±7.5V 2 0 ±15V -2 -4 -6 -6 ±2 ±4 ±6 ±8 ±10 ±12 ±14 -50 ±16 -25 0 25 50 75 100 125 SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [℃] Fig.76 Input Offset Voltage - Supply Voltage (Vicm=0V, Vout=0V) Fig.77 Input Offset Voltage - Ambient Temperature (Vicm=0V, Vout=0V) 200 180 180 160 160 INPUT BIAS CURRENT [nA] INPUT BIAS CURRENT [nA] . 200 140 -40℃ 25℃ 120 100 80 60 105℃ 40 20 140 ±7.5V ±4V 120 100 80 60 ±15V 40 20 0 0 ±2 ±4 ±6 ±8 ±10 ±12 ±14 ±16 -50 -25 SUPPLY VOLTAGE [V] 0 25 50 75 100 125 AMBIENT TEMPERATURE [℃] Fig.78 Input Bias Current - Supply Voltage (Vicm=0V, Vout=0V) Fig.79 Input Bias Current - Ambient Temperature (Vicm=0V, Vout=0V) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 30/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ○BA4564W 60 INPUT OFFSET CURRENT [nA] INPUT OFFSET CURRENT [nA] 60 40 -40℃ 20 105℃ 0 -20 25℃ -40 40 ±15V 0 ±7.5V -20 -40 -60 -60 ±0 ±2 -50 ±4 ±6 ±8 ±10 ±12 ±14 ±16 SUPPLY VOLTAGE [V] COMMON MODE REJECTION RATIO [dB] 5 4 -40℃ 3 25℃ 2 105℃ 1 0 -1 -2 -3 -4 -5 0 2 4 6 -25 0 25 50 75 100 AMBIENT TEMPERATURE [°C] 125 Fig.81 Input Offset Current - Ambient Temperature (Vicm=0V, Vout=0V) Fig.80 Input Offset Current - Supply Voltage (Vicm=0V, Vout=0V) INPUT OFFSET VOLTAGE [mV] ±4V 20 150 125 100 75 50 25 0 -50 8 COMMON MODE INPUT VOLTAGE [V] -25 0 25 50 75 100 AMBIENT TEMPERATURE [°C] 125 Fig.83 Common Mode Rejection Ratio - Ambient Temperature (VCC/VEE=+15V/-15V, Vicm=-12V to +12V) Fig.82 Input Offset Voltage - Common Mode Input Voltage (VCC=8V, Vout=4V) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 31/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet 150 . 5.0 125 4.0 SLEW RATE [V/µs] POWER SUPPLY REJECTION RATIO [dB] . ○BA4564W 100 75 50 3.0 2.0 1.0 25 0 0.0 -50 -25 0 25 50 75 100 AMBIENT TEMPERATURE [℃] 125 ±2 ±6 ±8 ±10 ±12 SUPPLY VOLTAGE [V] ±14 ±16 Fig.85 Slew Rate - Supply Voltage (CL=100pF, RL=2kΩ, Ta=25℃) Fig.84 Power Supply Rejection Ratio - Ambient Temperature (VCC/VEE=+4V/-4V to +15V/-15V) 80 1 TOTAL HARMONIC DISTORTION [%] INPUT REFERRED NOISE VOLTAGE [nV/√Hz] . ±4 60 40 20 10 100 1000 20kHz 1kHz 0.01 0.001 20Hz 0.0001 0.1 0 1 0.1 10000 FREQUENCY [Hz] Fig.86 Equivalent Input Noise Voltage - Frequency (VCC/VEE=+15V/-15V,RS=100Ω, Ta=25℃) 1 OUTPUT VOLTAGE [Vrms] 10 Fig.87 Total Harmonic Distortion - Output Voltage (VCC/VEE=+15V/-15V, AV=20dB, RL=2kΩ,80kHz-LPF, Ta=25℃) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 32/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet 60 25 50 -200 PHASE 20 15 10 -140 40 30 -170 -110 GAIN -80 20 PHASE [deg] 30 VOLTAGE GAIN [dB] MAXIMUM OUTPUT VOLTAGE SWING [VP-P] ○BA4564W -50 10 5 -20 0 1.E+01 1.E+02 1.E+03 1.E+04 1.E+05 1.E+06 10 102 103 104 105 106 FREQUENCY [Hz] Fig.88 Maximum Output Voltage Swing – Frequency (VCC/VEE=+15V/-15V, RL=2kΩ,Ta=25℃) 0 1.E+00 102 3 4 1.E+02 10 101.E+04 105 1.E+06 106 1.E+08 107 FREQUENCY [Hz] Fig.89 Voltage Gain - Frequency (VCC/VEE=+15V/-15V, AV=40dB, RL=2kΩ, Ta=25℃) (*)The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 33/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ●Application Information Test circuit1 NULL method VCC, VEE, EK, Vicm Unit: V Parameter VF S1 S2 S3 VCC VEE EK Vicm calculation Input Offset Voltage VF1 ON ON OFF 15 -15 0 0 1 Input Offset Current VF2 OFF OFF OFF 15 -15 0 0 2 VF3 OFF ON OFF -15 0 ON 15 0 VF4 OFF 0 0 ON ON ON ON ON OFF ON ON OFF Input Bias Current VF5 Large Signal Voltage Gain VF6 Common-mode Rejection Ratio VF7 (Input common-mode Voltage Range) VF8 Power Supply VF9 Rejection Ratio VF10 15 -15 0 0 15 -15 0 0 3 -27 0 0 27 -3 0 0 4 -4 0 0 15 -15 0 0 -Calculation1. Input Offset Voltage (Vio) VF1 Vio [V] 1 + Rf / Rs 4 5 6 0.1μF Rf=50kΩ 2. Input Offset Current (Iio) VF2 - VF1 Iio [A] Ri × (1 + Rf / Rs) 0.1μF 500kΩ SW1 VCC EK +15V Rs=50Ω 3. Input Bias Current (Ib) VF4 - VF3 Ib 2 × Ri × (1 + Rf / Rs) 3 Ri=10kΩ Ri=10kΩ [A] 4. Large Signal Voltage Gain (Av) ΔEK × (1+ Rf/Rs) Av 20 × Log VF5 - VF6 500kΩ DUT NULL SW3 Rs=50Ω Vicm 1000pF V RL SW2 50kΩ [dB] VF VEE -15V Fig. 90 Test circuit1 (one channel only) 5. Common-mode Rejection Ration (CMRR) ΔVicm × (1+ Rf/Rs) CMRR 20 × Log [dB] VF8 - VF7 6. Power supply rejection ratio (PSRR) ΔVcc × (1+ Rf/Rs) PSRR 20 × Log [dB] VF10 - VF9 Test Circuit 2 Switch Condition SW No. SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8 SW9 SW10 SW11 SW12 SW13 SW14 Supply Current OFF OFF OFF ON OFF ON OFF OFF OFF OFF OFF OFF OFF OFF High Level Output Voltage OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF ON OFF Low Level Output Voltage OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF OFF ON OFF Slew Rate OFF OFF OFF Unity Gain Frequency OFF ON ON OFF OFF OFF OFF OFF ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF ON ON ON ON Total Harmonic Distortion ON OFF OFF OFF ON OFF ON ON ON OFF OFF OFF Input Referred Noise Voltage ON OFF OFF OFF ON ON OFF OFF OFF OFF ON OFF OFF OFF www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 34/41 OFF OFF OFF OFF TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet Input voltage SW4 R2 SW5 VH VCC A VL － SW1 SW2 SW6 RS SW7 Output voltage SW8 R1 t Input wave ＋ SW3 SW9 SW10 SW11 SW12 SW13 SW14 VEE 90% SR=ΔV/Δt VH C A ～ VIN- VIN+ ～ RL CL V ～ ΔV V 10% VOUT VL Δt t Output wave Fig.91 Test Circuit 2 (each Op-Amp) Fig. 92 Slew Rate Input Waveform Test Circuit 3 Channel Separation VCC VCC R1//R2 R1//R2 OTHER CH VEE R1 VIN R2 VEE V VOUT1 R1 R2 V =0.5[Vrms] CS＝20×log VOUT2 100×VOUT1 VOUT2 Fig. 93 Test circuit 3 (VCC=+15V, VEE=-15V, R1=1kΩ, R2=100kΩ) www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 35/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ●Power Dissipation Power dissipation(total loss) indicates the power that can be consumed by IC at Ta=25℃(normal temperature). IC is heated when it consumed power, and the temperature of IC chip becomes higher than ambient temperature. The temperature that can be accepted by IC chip depends on circuit configuration, manufacturing process, and consumable power is limited. Power dissipation is determined by the temperature allowed in IC chip(maximum junction temperature) and thermal resistance of package(heat dissipation capability). The maximum junction temperature is typically equal to the maximum value in the storage temperature range. Heat generated by consumed power of IC radiates from the mold resin or lead frame of the package. The parameter which indicates this heat dissipation capability(hardness of heat release)is called thermal resistance, represented by the symbol θja℃/W. The temperature of IC inside the package can be estimated by this thermal resistance. Fig.94(a) shows the model of thermal resistance of the package. Thermal resistance θja, ambient temperature Ta, junction temperature Tj, and power dissipation Pd can be calculated by the equation below: θja = (Tjmax-Ta) / Pd ℃/W ・・・・・ (Ⅰ) Derating curve in Fig.94 (b) indicates power that can be consumed by IC with reference to ambient temperature. Power that can be consumed by IC with reference to ambient temperature. Power that can be consumed by IC begins to attenuate at certain ambient temperature. This gradient is determined by thermal resistance θja. Thermal resistance θja depends on chip size, power consumption, package, ambient temperature, package condition, wind velocity, etc even when the same of package is used. Thermal reduction curve indicates a reference value measured at a specified condition. Fig.95(c), to , (e) show a derating curve for an example of BA4560, BA4560R, BA4564R, BA4564W. PowerLSIの dissipation of LSI [W] 消 費 電 力 [W] Pd (max) θja=(Tjmax-Ta)/Pd ℃/W θja2 < θja1 P2 Ta [℃] Ta [℃] 周囲温度 Ambient temperature θ' ja2 P1 θ ja2 Tj ' (max) Tj (max) θ' ja1 Chip surface temperature Tj [℃] チップ 表面温度 Tj [℃] Power dissipation P [W] 0 25 消費電力 P [W] (a) Thermal resistance 600 * BA4560FJ( 17) * BA4560FV/FVT( 18) * BA4560FVM( 19) 400 200 0 25 50 75 100 AMBIENT TEMPERTURE [℃] . 125 . * BA4560FJ( 17) * BA4560FV/FVT( 18) 600 * BA4560FVM( 19) 400 200 (*17) 5.4 25 50 75 100 AMBIEN T TEMPERT URE [℃ ] 125 . (d)BA4560R (*18) 5 800 * BA4564RFV/WFV( 20) 600 400 200 0 0 (c)BA4560 (*16) 5.52 150 * BA4560F( 16) 800 0 0 125 1000 POWER DISSIPATION [mW] PO WER DISSIPATIO N [mW] . * BA4560F( 16) 100 (b) Derating curve Fig. 94Thermal resistance and derating curve 1000 800 75 ] [℃] 囲 温 度 Ta [℃Ta Ambient 周 temperature 1000 POWER DISSIPATION [mW] . 50 θ ja1 (*19) 4.7 (*20) 7 0 25 50 75 100 AMBIENT TEMPERATURE [℃] 125 (e)BA4564R/BA4564W Unit mW/℃ When using the unit above Ta=25℃, subtract the value above per degree℃. Permissible dissipation is the value. Permissible dissipation is the value when FR4 glass epoxy board 70mm ×70mm ×1.6mm (cooper foil area below 3%) is mounted. Fig. 95 Derating curve www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 36/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet Examples of circuit ○Voltage follower Voltage gain is 0 dB. This circuit controls output voltage (Vout) equal input voltage (Vin), and keeps Vout with stable because of high input impedance and low output impedance. Vout is shown next formula. Vout=Vin VCC Vout Vin VEE Fig. 96 Voltage follower circuit ○Inverting amplifier R2 For inverting amplifier, Vi(b) Derating curve voltage gain decided R1 and R2, and phase reversed voltage is outputted. Vout is shown next formula. Vout=-(R2/R1)・Vin Input impedance is R1. VCC Vin R1 Vout R1//R2 VEE Fig. 97 Inverting amplifier circuit ○Non-inverting amplifier R1 R2 VCC Vout For non-inverting amplifier, Vin is amplified by voltage gain decided R1 and R2, and phase is same with Vin. Vout is shown next formula. Vout=(1 + R2/R1)・Vin This circuit realizes high input impedance because Input impedance is operational amplifier’s input Impedance. Vin VEE Fig. 98 Non-inverting amplifier circuit www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 37/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV ●Operational Notes 1) Processing of unused circuit It is recommended to apply connection (see the Fig.99) and set the non inverting input terminal at the potential within input common-mode voltage range (Vicm), for any unused circuit. 2) Input voltage Applying (VEE - 0.3) to (VEE + 36)V BA4560R, 4564R, BA4564W)to the input terminal is possible without causing deterioration of the electrical characteristics or destruction, irrespective of the supply voltage. However, this does not ensure normal circuit operation. Please note that the circuit operates normally only when the input voltage is within the common mode input voltage range of the electric characteristics. 3) Maximum output voltage Because the output voltage range becomes narrow as the output current Increases, design the application with margin by considering changes in electrical characteristics and temperature characteristics. 4) Short-circuit of output terminal When output terminal and VCC or VEE terminal are shorted, excessive Output current may flow under some conditions, and heating may destroy IC. It is necessary to connect a resistor as shown in Fig.100, thereby protecting against load shorting. 5) Power supply (split supply / single supply) in used Op-amp operates when specified voltage is applied between VCC and VEE. Therefore, the single supply Op-Amp can be used for double supply Op-Amp as well. Datasheet VCC + Connect to Vicm Vicm VEE Fig. 99 The example of application circuit for unused op-amp VCC + protection resistor VEE Fig. 100 The example of output short protection 6) Power dissipation (Pd) Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions. 7) Short-circuit between pins and wrong mounting Pay attention to the assembly direction of the ICs. Wrong mounting direction or shorts between terminals, GND, or other components on the circuits, can damage the IC. 8) Use in strong electromagnetic field Using the ICs in strong electromagnetic field can cause operation malfunction. 9) Radiation This IC is not designed to be radiation-resistant. 10) IC Handling When stress is applied to IC because of deflection or bend of board, the characteristics may fluctuate due to piezoelectric (piezo) effect. 11) Inspection on set board During testing, turn on or off the power before mounting or dismounting the board from the test Jig. Do not power up the board without waiting for the output capacitors to discharge. The capacitors in the low output impedance terminal can stress the device. Pay attention to the electro static voltages during IC handling, transportation, and storage. 12) Output capacitor When VCC terminal is shorted to VEE (GND) potential and an electric charge has accumulated on the external capacitor, connected to output terminal, accumulated charge may be discharged VCC terminal via the parasitic element within the circuit or terminal protection element. The element in the circuit may be damaged (thermal destruction). When using this IC for an application circuit where there is oscillation, output capacitor load does not occur, as when using this IC as a voltage comparator. Set the capacitor connected to output terminal below 0.1μF in order to prevent damage to IC. Status of this document The Japanese version of this document is formal specification. A customer may use this translation version only for a reference to help reading the formal version. If there are any differences in translation version of this document formal version takes priority. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 38/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ●Physical Dimensions Tape and Reel Information SOP8 <Tape and Reel information> 5.0±0.2 (MAX 5.35 include BURR) 6 +6° 4° −4° 5 4.4±0.2 6.2±0.3 1 2 3 0.9±0.15 7 0.3MIN 8 Tape Embossed carrier tape Quantity 2500pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 4 0.595 1.5±0.1 +0.1 0.17 -0.05 S S 0.11 0.1 1.27 1pin 0.42±0.1 Reel (Unit : mm) Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. SSOP-B8 <Tape and Reel information> 3.0±0.2 (MAX 3.35 include BURR) 8 7 6 5 Tape Embossed carrier tape Quantity 2500pcs E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 0.3MIN 6.4 ± 0.3 4.4 ± 0.2 Direction of feed 2 3 4 0.1 1.15±0.1 1 0.15±0.1 S (0.52) 0.1 S +0.06 0.22 −0.04 0.65 0.08 1pin M Reel (Unit : mm) Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. SOP-J8 <Tape and Reel information> 4.9±0.2 (MAX 5.25 include BURR) +6° 4° −4° 6 5 0.45MIN 7 3.9±0.2 6.0±0.3 8 1 2 3 Tape Embossed carrier tape Quantity 2500pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 4 0.545 0.2±0.1 0.175 1.375±0.1 S 1.27 0.42±0.1 0.1 S 1pin (Unit : mm) www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 Reel 39/41 Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet MSOP8 <Tape and Reel information> 2.8±0.1 4.0±0.2 8 7 6 5 0.6±0.2 +6° 4° −4° 0.29±0.15 2.9±0.1 (MAX 3.25 include BURR) Tape Embossed carrier tape Quantity 3000pcs Direction of feed TR The direction is the 1pin of product is at the upper right when you hold ( reel on the left hand and you pull out the tape on the right hand ) 1 2 3 4 1PIN MARK 1pin +0.05 0.145 −0.03 0.475 0.08±0.05 0.75±0.05 0.9MAX S +0.05 0.22 −0.04 0.08 S Direction of feed 0.65 Reel (Unit : mm) ∗ Order quantity needs to be multiple of the minimum quantity. TSSOP-B8 <Tape and Reel information> 3.0 ± 0.1 (MAX 3.35 include BURR) 8 7 6 4±4 3000pcs 2 0.525 3 4 1PIN MARK E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 1.0±0.2 0.5±0.15 6.4±0.2 4.4±0.1 +0.05 0.145 −0.03 S 0.1±0.05 1.2MAX Embossed carrier tape Quantity Direction of feed 1 1.0±0.05 Tape 5 0.08 S +0.05 0.245 −0.04 0.08 M Direction of feed 1pin 0.65 Reel (Unit : mm) ∗ Order quantity needs to be multiple of the minimum quantity. SSOP-B14 <Tape and Reel information> 5.0 ± 0.2 8 0.3Min. 4.4 ± 0.2 6.4 ± 0.3 14 1 Tape Embossed carrier tape Quantity 2500pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 7 0.10 1.15 ± 0.1 0.15 ± 0.1 0.65 0.1 0.22 ± 0.1 1pin (Unit : mm) www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 Reel 40/41 Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV Datasheet ●Marking Diagrams SOP8(TOP VIEW) SSOP-B8(TOP VIEW) Part Number Marking Part Number Marking LOT Number LOT Number 1PIN MARK 1PIN MARK MSOP8(TOP VIEW) TSSOP-B8(TOP VIEW) Part Number Marking Part Number Marking LOT Number LOT Number 1PIN MARK 1PIN MARK SOP-J8(TOP VIEW) SSOP-B14(TOP VIEW) Part Number Marking Part Number Marking LOT Number LOT Number 1PIN MARK 1PIN MARK Product Name BA4560 Package Type F SOP8 FJ SOP-J8 FV SSOP-B8 FVT TSSOP-B8 FVM MSOP8 FJ SOP-J8 F SOP8 FJ SOP-J8 Marking 4560 FV SSOP-B8 FVT TSSOP-B8 FVM MSOP8 FJ SOP-J8 BA4564R FV SSOP-B14 4564R BA4564W FV SSOP-B14 4564W BA4560R www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･00 4560R 41/41 TSZ02201-0RAR1G200020-1-2 7.SEP.2012 Rev.002 Datasheet Notice ●General Precaution 1) Before you use our Products, you are requested to carefully read this document and fully understand its contents. ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any ROHM’s Products against warning, caution or note contained in this document. 2) All information contained in this document is current as of the issuing date and subject to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales representative. ●Precaution on using ROHM Products 1) Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment, transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. 2) ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3) Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4) The Products are not subject to radiation-proof design. 5) Please verify and confirm characteristics of the final or mounted products in using the Products. 6) In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse) is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7) De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8) Confirm that operation temperature is within the specified range described in the product specification. 9) ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Notice - Rev.003 © 2012 ROHM Co., Ltd. All rights reserved. Datasheet ●Precaution for Mounting / Circuit board design 1) When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2) In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification ●Precautions Regarding Application Examples and External Circuits 1) If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2) You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. ●Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). ●Precaution for Storage / Transportation 1) Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2) Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3) Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4) Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. ●Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. ●Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. ●Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. ●Precaution Regarding Intellectual Property Rights 1) All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2) No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Notice - Rev.003 © 2012 ROHM Co., Ltd. All rights reserved. Datasheet ●Other Precaution 1) The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or concerning such information. 2) This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 3) The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 4) In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 5) The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice - Rev.003 © 2012 ROHM Co., Ltd. All rights reserved.