MURF2020 THRU MURF2060 R GLASS PASSIVATED SUPER FAST RECTIFIER Reverse Voltage - 200 -600 Volts Forward Current - 20.0Amperes S E M I C O N D U C T O R FEATURES ITO-220AC Plastic package has Underwriters Laboratory Flammability Classification 94V-0 Fast switching for high efficiency Low forward voltage drop Fred chip Planer construction High surge capability High temperature soldering guaranteed:260°C/10 seconds, JF 0.25"(6.35mm)from case MURF2060 Component in accordance to RoHS 2011/65/EU 0.187(4.75) 0.167(4.25) 0.140(3.55) 0.410(10.42) 0.388(9.85) 0.128(3.25) DIA 0.130(3.31) 0.110(2.81) 0.111(2.83) 0.272(6.90) 0.101(2.57) 1 PIN 0.256(6.50) 2 1.161(29.50) 0.177(4.50) 0.136(3.45) 1.083(27.50) 0.138(3.50) 0.551(14.00) 0.102(2.60) 0.496(12.60) 0.056(1.43) 0.043(1.10) 0.029(0.73) 0.019(0.47) MECHANICAL DATA 0.208(5.28) 0.029(0.73) 0.192(4.88) 0.019(0.47) Case: JEDEC ITO-220AC molded plastic body Terminals: Lead solderable per MIL-STD-750,method 2026 Polarity: As marked. Mounting Position: Any Dimensions inches and (millimeters) Dimensions in in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS (Ratings at 25°C ambient temperature unless otherwise specified ,Single phase ,half wave ,resistive or inductive load. For capacitive load,derate by 20%.) Symbols MURF 2020 MURF 2040 MURF 2060 VRRM VRMS VDC 200 400 600 140 280 420 200 400 600 Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Units Volts Volts Volts Maximum average forward rectified current(see Fig.1) I(AV) 20.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 150.0 150 Amps Maximum instantaneous forward voltage at 20.0 A per leg(Note 1 ) Maximum instantaneous reverse current at rated DC blocking voltage(Note 1) T A =25°C TA =125°C Maximum Reverse Recovery Time (Note 2) Typical thermal resistance (Note 3) Operating junction temperature range Storage temperature range VF 1.0 1.5 10 IR Trr 1.3 μA 250 35 Volts 50 ns RθJC 2.5 °C/W TJ TSTG -55 to+150 °C -55 to+150 °C Notes: 1. Pulse test: 300μs pulse width,1% duty cycle 2. Reverse recovery test conditions IF=0.5A,IR=1.0A, Irr=0.25A 3. Thermal resistance from junction to case JINAN JINGHENG ELECTRONICS CO., LTD. 2-1 HTTP://WWW.JINGHENGGROUP.COM RATINGS AND CHARACTERISTIC CURVES MURF2020 THRU MURF2060 FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT(AMPERES) AVERAGE FORWARD CURRENT AMPERES FIG.1-FORWARD CURRENT DERATING CURVE 24 20 16 12 8 4 0 0 20 40 60 80 100 120 150 AMBIENT TEMPERATURE (°C) 175 8.3ms Single Half Sine-Wave (JEDEC Method) 150 125 100 75 50 25 0 1 2 5 50 20 FIG.4-TYPICAL REVERSE CHARACTERISTICS 20 50 10 10 TJ=100°C (uA) 200V 400V 600V INSTANTANEOUS REVERSE CURRENT INSTANTANEOUS FORWARD CURRENT( AMPERES) 10 NUMBER OF CYCLES AT 60Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PULSE WIDTH=300μS 1% DUTY CYCLE 1 0.1 1 TJ=25°C 0.1 0.01 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 0.001 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE% JINAN JINGHENG ELECTRONICS CO., LTD. 2-2 HTTP://WWW.JINGHENGGROUP.COM 100