RECTRON HFM201W SEMICONDUCTOR THRU TECHNICAL SPECIFICATION HFM208W SURFACE MOUNT HIGH EFFICIENCY SILICON RECTIFIER VOLTAGE RANGE 50 to 1000 Volts CURRENT 2.0 Amperes FEATURES * * * * * Ideal for surface mounted applications Low leakage current Metallurgically bonded construction Mounting position: Any Weight: 0.098 gram .220 (5.59) .205 (5.21) MECHANICAL DATA .155 (3.94) .130 (3.30) .180 (4.57) .160 (4.06) .096 (2.44) .084 (2.13) .008 (0.20) .012 (0.305) .006 (0.152) .083 (2.11) .077 (1.96) .010 (0.25) * Epoxy : Device has UL flammability classification 94V-0 .060 (1.52) .030 (0.76) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (At TA = 25oC unless otherwise noted) RATINGS SYMBOL HFM201W HFM202W HFM203W HFM204W HFM205W HFM206W HFM207W HFM208W UNITS Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 300 400 600 800 1000 Volts Maximum RMS Volts VRMS 35 70 140 210 280 420 560 700 Volts Maximum DC Blocking Voltage VDC 50 100 200 300 400 600 800 1000 Volts Maximum Average Forward Current at TA = 50oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range IO 2.0 Amps 60 IFSM CJ 30 TJ, TSTG Amps 20 pF 0 -55 to + 150 C ELECTRICAL CHARACTERISTICS (At TA = 25oC unless otherwise noted) CHARACTERISTICS Maximum Forward Voltage at 2.0A DC SYMBOL VF Maximum Full Load Reverse Current, Full cycle Average TA = 55oC Maximum DC Reverse Current at @TA = 25oC Rated DC Blocking Voltage @TA = 125oC IR Maximum Reverse Recovery Time (Note 1) trr NOTES : 1. Test Conditions: IF=0.5A, IR=-1.0A, IRR=-0.25A. 2. Measured at 1 MHZ and applied reverse voltage of 4.0 volts. HFM201W HFM202W HFM203W HFM204W HFM205W HFM206W HFM207W HFM208W 1.0 1.3 50 1.7 UNITS Volts 50 uAmps 5.0 100 uAmps uAmps 75 nSec 2002-11 AVERAGE FORWARD CURENT, (A) RATING AND CHARACTERISTIC CURVES ( HFM201W THRU HFM208W ) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC trr +0.5A (-) (+) -1.0A 1cm SET TIME BASE FOR 10/20 ns/cm 1 megohm. 22pF. 2. Rise Time = 10ns max. Source Impedance = 50 ohms. TJ = 25 .1 .1 20 HF 8W M2 0 W 203 M2 FM ~H W 01W ~H FM 1.0 HF 1.0 5W INSTANTANEOUS FORWARD CURRENT, (A) 10 TJ = 25 .01 Pulse Width = 300uS 1% Duty Cycle .001 0 20 40 60 80 100 120 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) 140 0 70 60 8.3ms Single Half Sine-Wave (JEDEC Method) 50 40 30 20 10 0 1 2 5 10 20 50 NUMBER OF CYCLES AT 60Hz 100 .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG. 6 - TYPICAL JUNCTION CAPACITANCE FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT JUNCTION CAPACITANCE, (pF) INSTANTANEOUS REVERSE CURRENT, (uA) TJ = 100 .01 PEAK FORWARD SURGE CURRENT, (A) TJ = 150 10 0 25 50 75 100 125 150175 AMBIENT TEMPERATURE ( FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 100 0 W~ NOTES:1 Rise Time = 7ns max. Input Impedance = 06 OSCILLOSCOPE (NOTE 1) 2.0 04 1 NONINDUCTIVE -0.25A Single Phase Half Wave 60Hz Resistive or Inductive Load M2 25 Vdc (approx) (-) 0 PULSE GENERATOR (NOTE 2) 4.0 M2 D.U.T (+) FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE HF 10 NONINDUCTIVE HF 50 NONINDUCTIVE 200 100 60 40 HFM 201 W~ HFM 20 HFM 206 10 TJ = 25 6 4 W~H 205 W FM2 08W 2 1 .1 .2 .4 1.0 2 4 10 20 40 100 REVERSE VOLTAGE, ( V ) RECTRON ) Mounting Pad Layout 0.106 MAX. (2.69 MAX.) 0.083 MIN. (2.10 MIN.) 0.050 MIN. (1.27 MIN.) 0.220 REF Dimensions in inches and (millimeters) RECTRON