DATA SHEET NPN SILICON GERMANIUM RF TRANSISTOR NESG220033 NPN SiGe RF TRANSISTOR FOR UHF-BAND, LOW NOISE, LOW DISTORTION AMPLIFICATION 3-PIN MINIMOLD (33 PKG) FEATURES • The device is an ideal choice for low noise, low distortion amplification. NF = 0.75 dB TYP. @ VCE = 5 V, IC = 10 mA, f = 1 GHz • PO (1 dB) = 21.5 dBm TYP. @ VCE = 5 V, IC (set) = 40 mA, f = 1 GHz • OIP3 = 35 dBm TYP. @ VCE = 5 V, IC (set) = 40 mA, f = 1 GHz • Maximum stable power gain: MSG =14.0 dB TYP. @ VCE = 5 V, IC = 40 mA, f = 1 GHz • SiGe HBT technology (UHS2) : fT = 12.5 GHz • This product is improvement of ESD of NESG2xxx series. • 3-pin minimold (33 PKG) ORDERING INFORMATION Part Number NESG220033 Order Number Package NESG220033-A NESG220033-T1B Quantity Supplying Form 3-pin minimold 50 pcs • 8 mm wide embossed taping (33 PKG) (Pb-Free) (Non reel) • Pin 3 (Collector) face the perforation side NESG220033-T1B-A 3 kpcs/reel of the tape Remark To order evaluation samples, please contact your nearby sales office. Unit sample quantity is 50 pcs. ABSOLUTE MAXIMUM RATINGS (TA = +25°C) Parameter Symbol Ratings Unit Collector to Base Voltage VCBO 5.5 V Collector to Emitter Voltage VCES 13 V Collector to Emitter Voltage VCEO 5.5 V Note 1 IB 36 mA Collector Current IC 200 mA 480 mW Base Current Total Power Dissipation Ptot Note 2 Junction Temperature Tj 150 °C Storage Temperature Tstg −65 to +150 °C Notes 1. Depend on the ESD protect device. 2. Mounted on 3.8 cm × 9.0 cm × 0.8 mm (t) glass epoxy PWB Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge. The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. Document No. PU10766EJ03V0DS (3rd edition) Date Published November 2009 NS Printed in Japan The mark <R> shows major revised points. The revised points can be easily searched by copying an "<R>" in the PDF file and specifying it in the "Find what:" field. 2009 NESG220033 THERMAL RESISTANCE (TA = +25°C) Parameter Termal Resistance from Junction to Note Ambient Symbol Ratings Unit Rthj-a 260 °C/W Note Mounted on 3.8 cm × 9.0 cm × 0.8 mm (t) glass epoxy PWB RECOMMENDED OPERATING RANGE (TA = +25°C) Parameter <R> Collector Current Symbol MIN. TYP. MAX. Unit IC − 40 − mA ELECTRICAL CHARACTERISTICS (TA = +25°C) Parameter Symbol Test Conditions MIN. TYP. MAX. Unit DC Characteristics Collector Cut-off Current ICBO VCB = 5 V, IE = 0 mA − − 100 nA Emitter Cut-off Current IEBO VEB = 0.4 V, IC = 0 mA − − 100 nA VCE = 5 V, IC = 10 mA 140 180 260 − VCE = 5 V, IC = 40 mA, f = 1 GHz − 12.5 − GHz ⏐S21e⏐ VCE = 5 V, IC = 40 mA, f = 1 GHz 11.0 13.0 − dB Noise Figure (1) NF1 VCE = 5 V, IC = 10 mA, f = 1 GHz, ZS = ZSopt, ZL = 50 Ω − 0.75 1.15 dB Noise Figure (2) NF2 VCE = 5 V, IC = 40 mA, f = 1 GHz, ZS = ZSopt, ZL = ZLopt − 0.9 − dB Associated Gain (1) Ga1 VCE = 5 V, IC = 10 mA, f = 1 GHz, ZS = ZSopt, ZL = 50 Ω 10.0 12.0 − dB Associated Gain (2) Ga2 VCE = 5 V, IC = 40 mA, f = 1 GHz, ZS = ZSopt, ZL = ZLopt − 13.5 − dB VCB = 5 V, IE = 0 mA, f = 1 MHz − 0.7 0.9 pF VCE = 5 V, IC = 40 mA, f = 1 GHz 12.0 14.0 − dB VCE = 5 V, IC (set) = 40 mA, f = 1 GHz, ZS = ZSopt, ZL = ZLopt − 21.5 − dBm VCE = 5 V, IC (set) = 40 mA, f = 1 GHz, − 35 − dBm DC Current Gain hFE Note 1 RF Characteristics Gain Bandwidth Product fT 2 Insertion Power Gain Reverse Transfer Capacitance Maximum Stable Power Gain Cre Note 2 MSG Note 3 Gain 1 dB Compression Output Power PO (1 dB) Output 3rd Order Intercept Point OIP3 Δf = 1 MHz, ZS = ZSopt, ZL = ZLopt Notes 1. Pulse measurement: PW ≤ 350 μs, Duty Cycle ≤ 2% 2. Collector to base capacitance when the emitter grounded. 3. MSG = S21 S12 hFE CLASSIFICATION 2 Rank FB Marking R7B hFE Value 140 to 260 Data Sheet PU10766EJ03V0DS NESG220033 TYPICAL CHARACTERISTICS (TA = +25°C, unless otherwise specified) TOTAL POWER DISSIPATION vs. AMBIENT TEMPERATURE REVERSE TRANSFER CAPACITANCE vs. COLLECTOR TO BASE VOLTAGE Reverse Transfer Capacitance Cre (pF) Total Power Dissipation Ptot (mW) 1 000 3.8 cm × 9.0 cm × 0.8 mm (t), FR–4 500 480 0 25 50 75 100 125 1.1 f = 1 MHz 1.0 0.9 0.8 0.7 0.6 0.5 0 150 2 3 4 5 Ambient Temperature TA (°C) Collector to Base Voltage VCB (V) COLLECTOR CURRENT vs. BASE TO EMITTER VOLTAGE COLLECTOR CURRENT vs. BASE TO EMITTER VOLTAGE 100 100 VCE = 3 V VCE = 5 V 10 Collector Current IC (mA) Collector Current IC (mA) 1 1 0.1 0.01 0.001 0.0001 0.4 0.5 0.6 0.7 0.8 0.9 10 1 0.1 0.01 0.001 0.0001 0.4 Base to Emitter Voltage VBE (V) 0.5 0.6 0.7 0.8 0.9 Base to Emitter Voltage VBE (V) COLLECTOR CURRENT vs. COLLECTOR TO EMITTER VOLTAGE Collector Current IC (mA) 200 1 700 μA 1 500 μ A 1 300 μ A 1 100 μ A 150 900 μ A 700 μ A 100 500 μA 300 μ A 50 IB = 100 μA 0 0 1 2 3 4 5 Collector to Emitter Voltage VCE (V) Remark The graphs indicate nominal characteristics. Data Sheet PU10766EJ03V0DS 3 NESG220033 DC CURRENT GAIN vs. COLLECTOR CURRENT DC CURRENT GAIN vs. COLLECTOR CURRENT 1 000 1 000 100 10 1 0.1 VCE = 5 V DC Current Gain hFE DC Current Gain hFE VCE = 3 V 1 10 100 10 100 Collector Current IC (mA) GAIN BANDWIDTH PRODUCT vs. COLLECTOR CURRENT GAIN BANDWIDTH PRODUCT vs. COLLECTOR CURRENT 1 000 20 VCE = 3 V, f = 1 GHz 15 10 5 10 100 VCE = 5 V, f = 1 GHz 15 10 5 0 1 Collector Current IC (mA) 10 Collector Current IC (mA) Remark The graphs indicate nominal characteristics. 4 1 Collector Current IC (mA) Gain Bandwidth Product fT (GHz) Gain Bandwidth Product fT (GHz) 10 1 0.1 1 000 20 0 1 100 Data Sheet PU10766EJ03V0DS 100 NESG220033 VCE = 3 V, IC = 10 mA 30 25 MSG 20 MAG MAG 15 |S21e| MSG 2 10 5 0 0.1 1 10 Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) 35 INSERTION POWER GAIN, MAG, MSG vs. FREQUENCY 35 VCE = 3 V, IC = 40 mA 30 25 MSG MAG 20 MAG 15 MSG 2 |S21e| 10 5 0 0.1 1 10 Frequency f (GHz) INSERTION POWER GAIN, MAG, MSG vs. FREQUENCY INSERTION POWER GAIN, MAG, MSG vs. FREQUENCY 35 VCE = 5 V, IC = 10 mA 30 25 MSG 20 MAG MAG 15 |S21e| MSG 2 10 5 0 0.1 1 10 Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) Frequency f (GHz) 35 VCE = 5 V, IC = 40 mA 30 25 MSG 20 MAG MAG MSG 15 2 |S21e| 10 5 0 0.1 1 10 Frequency f (GHz) Frequency f (GHz) INSERTION POWER GAIN, MAG, MSG vs. COLLECTOR CURRENT INSERTION POWER GAIN, MAG, MSG vs. COLLECTOR CURRENT 20 VCE = 3 V, f = 1 GHz MSG MAG 15 10 |S21e|2 5 0 1 10 100 Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) INSERTION POWER GAIN, MAG, MSG vs. FREQUENCY Collector Current IC (mA) 20 VCE = 5 V, f = 1 GHz MSG MAG 15 10 |S21e|2 5 0 1 10 100 Collector Current IC (mA) Remark The graphs indicate nominal characteristics. Data Sheet PU10766EJ03V0DS 5 NESG220033 NOISE FIGURE, ASSOCIATED GAIN vs. COLLECTOR CURRENT 3 14 Ga 12 10 8 2 6 1 4 NF 2 0 1 0 100 10 40 VCE = 5 V, f1 = 1.000 GHz, f2 = 1.001 GHz 30 20 10 0 1 10 100 Collector Current IC (mA) OUTPUT POWER, LINEAR GAIN, COLLECTOR CURRENT vs. INPUT POWER EACH OUTPUT POWER, IM3 vs. EACH INPUT POWER 20 300 Pout GL 10 200 0 100 IC –10 –20 –10 0 0 20 10 Collector Current IC (mA) 400 VCE = 5 V, IC (set) = 40 mA, f = 1 GHz Each Output Power Pout (each) (dBm) 3rd Order Intermodulation Distortion IM3 (dB) Collector Current IC (mA) 30 Output Power Pout (dBm) Linear Gain GL (dB) Output 3rd Order Intercept Point OIP3 (dBm) 16 VCE = 5 V, f = 1 GHz, ZS = ZSopt, ZL = 50 Ω Associated Gain Ga (dB) Noise Figure NF (dB) 4 OUTPUT 3RD ORDER INTERCEPT POINT vs. COLLECTOR CURRENT 40 30 20 10 Pout (each) 0 –10 –20 –30 –40 –50 –60 –70 –80 –20 IM3 –10 VCE = 5 V, IC (set) = 40 mA, f1 = 1.000 GHz, f2 = 1.001 GHz 0 10 20 30 Each Input Power Pin (each) (dBm) Input Power Pin (dBm) Remark The graphs indicate nominal characteristics. S-PARAMETERS S-parameters and noise parameters are provided on our Web site in a format (S2P) that enables the direct import of the parameters to microwave circuit simulators without the need for keyboard inputs. Click here to download S-parameters. [RF and Microwave] → [Device Parameters] URL http://www.necel.com/microwave/en/ 6 Data Sheet PU10766EJ03V0DS NESG220033 PACKAGE DIMENSIONS 3-PIN MINIMOLD (33 PKG) (UNIT: mm) 0.65+0.1 –0.15 1 3 0.4+0.1 –0.05 0.95 2 0.95 1.5 R7B Marking 0 to 0.1 1.1 to 1.4 0.16+0.1 –0.05 0.3 2.9±0.2 0.4+0.1 –0.05 2.8±0.2 PIN CONNECTIONS 1. Emitter 2. Base 3. Collector Data Sheet PU10766EJ03V0DS 7 NESG220033 • The information in this document is current as of November, 2009. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. • No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document. • NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others. • Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. • While NEC Electronics endeavors to enhance the quality and safety of NEC Electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. In addition, NEC Electronics products are not taken measures to prevent radioactive rays in the product design. When customers use NEC Electronics products with their products, customers shall, on their own responsibility, incorporate sufficient safety measures such as redundancy, fire-containment and anti-failure features to their products in order to avoid risks of the damages to property (including public or social property) or injury (including death) to persons, as the result of defects of NEC Electronics products. • NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to determine NEC Electronics' willingness to support a given application. (Note) (1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as defined above). M8E0904E