ON NCP729FC285T2G 200 ma ultra-low noise very-low iq, high psrr, ldo linear voltage regulator Datasheet

NCP729
200 mA Ultra-Low Noise
Very-Low Iq, High PSRR,
LDO Linear Voltage
Regulator
http://onsemi.com
The NCP729 is a 200 mA LDO suitable to provide clean analog
power supply rails for noise sensitive applications. This device
features Ultra−Low Noise performance, High Power Supply Rejection
Ratio and Very good transient response characteristics. Very Low
Dropout and Very Low Quiescent Current makes this LDO an
attractive choice for wide range of battery powered, portable products.
Current Limit and Thermal Shutdown provide protection during
failure conditions. NCP729 is available in 1.06 mm x 1.06 mm Chip
Scale Package and it is stable with small 1 mF Ceramic capacitors.
DEVICE MARKING INFORMATION
Features
•
•
•
•
•
•
•
•
•
•
•
•
Operating Input Voltage Range: 2.0 V to 5.5 V
Fixed Voltage Options Available: 0.8 V to 3.5 V
Very Low Quiescent Current: Max. 50 mA over Temperature
Ultra Low Noise: 10 mVRMS from 100 Hz to 100 kHz
Very Low Dropout: 86 mV Typical at 200 mA
±2% Accuracy over Full Load, Line and Temperature Variations
High PSRR: 72 dB at 1 kHz
Thermal Shutdown and Current Limit Protections
Stable with a 1 mF Ceramic Output Capacitor
Available in 1.06 mm x 1.06 mm 4−bump CSP Package
Active Output Discharge for Fast Turn−Off
These are Pb−free Devices
IN
CIN
OFF
ON
XXX
YWW
XXX = Specific Device Code
Y
= Year
WW = Work Week
PIN CONNECTIONS
EN
IN
A1
A2
B1
B2
(Top View)
PDAs, Tablets, GPS, Smartphones
Wireless Handsets, Wireless LAN, Bluetooth, Zigbee
Portable Medical Equipment
Other Battery Powered Applications
VIN
A1
GND OUT
Typical Applications
•
•
•
•
4 BUMP CSP
FC SUFFIX
CASE 568AD
EN
NCP729
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 12 of this data sheet.
VOUT
OUT
COUT
GND
1 mF
Ceramic
Figure 1. Typical Application Schematic
© Semiconductor Components Industries, LLC, 2012
August, 2012 − Rev. 1
1
Publication Order Number:
NCP729/D
NCP729
IN
ENABLE
LOGIC
EN
THERMAL
SHUTDOWN
UVLO
BANDGAP
REFERENCE
MOSFET
DRIVER WITH
CURRENT LIMIT
OUT
AUTO LOW
POWER MODE
ACTIVE
DISCHARGE
EN
EEPROM
GND
Figure 2. Simplified Schematic Block Diagram
Table 1. PIN FUNCTION DESCRIPTION
Pin No.
4−bump CSP
Pin Name
Description
B2
OUT
Regulated output voltage pin. A small 1 mF ceramic capacitor is needed from this pin to ground
to assure stability.
B1
GND
Power supply ground. Soldered to large copper plane allows for better heat dissipation.
A1
EN
Enable pin. Driving EN over 0.9 V turns on the regulator. Driving EN below 0.4 V puts the regulator into shutdown mode.
A2
IN
Input pin. A small capacitor is needed from this pin to ground to assure stability.
Table 2. ABSOLUTE MAXIMUM RATINGS
Rating
Symbol
Value
Unit
VIN
−0.3 V to 6 V
V
Output Voltage
VOUT
−0.3 V to VIN + 0.3 V
V
Enable Input
VEN
−0.3 V to VIN + 0.3 V
V
Input Voltage (Note 1)
Output Short Circuit Duration
tSC
∞
s
TJ(MAX)
125
°C
TSTG
−55 to 150
°C
ESD Capability, Human Body Model (Note 2)
ESDHBM
2000
V
ESD Capability, Machine Model (Note 2)
ESDMM
200
V
Maximum Junction Temperature
Storage Temperature
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Refer to ELECTRICAL CHARACTERISTIS and APPLICATION INFORMATION for Safe Operating Area.
2. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per AEC−Q100−002 (EIA/JESD22−A114)
ESD Machine Model tested per AEC−Q100−003 (EIA/JESD22−A115)
Latchup Current Maximum Rating tested per JEDEC standard: JESD78.
http://onsemi.com
2
NCP729
Table 3. THERMAL CHARACTERISTICS
Rating
Symbol
Thermal Characteristics, 4−bump CSP package
Thermal Resistance, Junction−to−Air (Note 3)
Thermal Resistance, Junction−to−Air (Note 4)
Value
RqJA
Unit
°C/W
90
157
3. Specified according to JEDEC 51.7 4−Layer Board.
4. Single component mounted on 4−Layer Board, 480 mm2, Top Layer thickness: 1 oz, Cu Area: 100 mm2.
Table 4. ELECTRICAL CHARACTERISTICS −40°C ≤ TJ ≤ 125°C; VIN = VOUT(NOM) + 0.3 V or 2.0 V, whichever is greater; IOUT =
10 mA, CIN = COUT = 1 mF unless otherwise noted. Typical values are at TJ = +25°C. (Note 5)
Parameter
Test Conditions
Operating Input Voltage
Symbol
Min
VIN
Typ
Max
Unit
2.0
5.5
V
−2
+2
%
Output Voltage Accuracy
VOUT + 0.3 V ≤ VIN ≤ 5.5 V
0 mA ≤ IOUT ≤ 200 mA
VOUT
Line Regulation
VOUT + 0.3 V ≤ VIN ≤ 5.5 V
RegLINE
150
mV/V
Load Regulation
IOUT = 0 mA to 200 mA
RegLOAD
2
mV/mA
Dropout Voltage (Note 6)
VDO = VIN – (VOUT(NOM) – 100 mV)
IOUT = 200 mA
VDO
170
100
90
80
80
70
65
220
140
130
120
120
110
100
mV
Quiescent Current
IOUT = 0 mA
IQ
35
50
mA
Ground Current
IOUT = 200 mA
IGND
255
155
300
200
mA
Disable Current
VEN = 0 V
IDIS
0.3
1
mA
Output Current Limit
VOUT = VOUT(NOM) – 100 mV
IOUT
250
400
530
mA
Output Short Circuit Current
VOUT = 0 V
ISC
250
400
530
mA
EN Pin Threshold Voltage
High Threshold
Low Threshold
VEN Voltage increasing
VEN Voltage decreasing
VEN_HI
VEN_LO
0.9
EN Pin Input Current
VEN = 5.5 V
IEN
100
Turn−on Time
VOUT = 0 V to 98% VOUT(NOM),
after assertion of the EN
tON
150
ms
Power Supply Rejection Ratio
VIN = 3.8 V, VOUT = 3.3 V
VPP = 100 mV
IOUT = 200 mA
PSRR
74
72
56
dB
Output Noise Voltage
VOUT = 1.8 V, IOUT = 200 mA
f = 100 Hz to 100 kHz
VN
10
mVrms
Line Transient
VOUT + 0.3 V ≤ VIN ≤ VOUT + 1.3 V or
VOUT + 0.3 V ≤ VIN ≤ VOUT + 1.3 V in 1 ms
±20
mV
Load Transient
IOUT = 1 mA to 200 mA or
IOUT = 200 mA to 1 mA in 1 ms
DVOUT
±80
mV
Undervoltage Lock−out
VIN rising from 0 V to 5.5 V
UVLO
Thermal Shutdown Temperature
Temperature increasing from TJ = +25°C
TSD
Thermal Shutdown Hysteresis
Temperature falling from TSD
TSDH
VOUT = 1.8 V
VOUT = 2.5 V
VOUT = 2.6 V
VOUT = 2.8 V
VOUT = 2.85 V
VOUT = 3.0 V
VOUT = 3.3 V
VOUT < 1.8 V
VOUT ≥ 1.8 V
V
f = 100 Hz
f = 1 kHz
f = 10 kHz
0.4
1.3
1.6
500
1.9
165
−
20
nA
V
°C
−
°C
5. Performance guaranteed over the indicated operating temperature range by design and/or characterization production tested at TJ = TA =
25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
6. Characterized when VOUT falls 100 mV below the regulated voltage at VIN = VOUT(NOM) + 0.3 V.
http://onsemi.com
3
NCP729
10
VIN = 2.0 V,
VOUT = 0.8 V,
CIN = COUT = 1 mF,
TA = 25°C
1
IOUT = 10 mA
0.1
IOUT = 1 mA
IOUT = 200 mA
0.01
0.001
10
100
1K
10 K
100 K
1M
1K
10 K
100 K
1M
PSRR (dB)
VIN = 2.3 V,
VOUT = 1.8 V,
CIN = none,
COUT = 1 mF,
TA = 25°C
100
IOUT = 100 mA
10 K
100 K
1M
IOUT = 10 mA
60
50
40
VIN = 3.3 V,
VOUT = 2.8 V,
CIN = none,
COUT = 1 mF,
TA = 25°C
30
20
IOUT = 200 mA
1K
10 M
IOUT = 1 mA
70
10
0
10 M
10
100
IOUT = 100 mA
IOUT = 200 mA
1K
10 K
100 K
1M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 5. PSRR, VOUT = 1.8 V, COUT = 1 mF
Figure 6. PSRR, VOUT = 2.8 V, COUT = 1 mF
90
10 M
90
IOUT = 1 mA
80
70
60
50
40
30
20
10
10
100
IOUT = 100 mA
10 K
100 K
1M
60
50
40
VIN = 3.8 V,
VOUT = 3.3 V,
CIN = none,
COUT = 4.7 mF,
TA = 25°C
30
20
IOUT = 200 mA
1K
IOUT = 10 mA
70
IOUT = 10 mA
VIN = 3.8 V,
VOUT = 3.3 V,
CIN = none,
COUT = 1 mF,
TA = 25°C
IOUT = 1 mA
80
PSRR (dB)
PSRR (dB)
100
80
40
0
10
90
50
10
IOUT = 200 mA
0.01
Figure 4. Output Voltage Noise,
VOUT = 3.3 V, COUT = 1 mF
60
0
IOUT = 1 mA
Figure 3. Output Voltage Noise,
VOUT = 0.8 V, COUT = 1 mF
IOUT = 10 mA
10
IOUT = 10 mA
0.1
FREQUENCY (Hz)
70
20
VIN = 3.6 V,
VOUT = 3.3 V,
CIN = COUT = 1 mF,
TA = 25°C
1
0.001
10 M
IOUT = 1 mA
30
10
FREQUENCY (Hz)
80
PSRR (dB)
OUTPUT VOLTAGE NOISE (mV/rtHz)
OUTPUT VOLTAGE NOISE (mV/rtHz)
TYPICAL CHARACTERISTICS
10
10 M
0
10
100
IOUT = 100 mA
IOUT = 200 mA
1K
10 K
100 K
1M
10 M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 7. PSRR, VOUT = 3.3 V, COUT = 1 mF
Figure 8. PSRR, VOUT = 3.3 V, COUT = 4.7 mF
http://onsemi.com
4
NCP729
200
CIN = 1 mF,
COUT = 1 mF,
VOUT = 0.8 V,
VIN = 2.0 V
TA = 25°C
TA = −40°C
QUIESCENT CURRENT (mA)
50
0.01
0.1
1
10
100
40
TA = 125°C
120
TA = 25°C
100
TA = −40°C
80
60
40
0.001
0.01
0.1
1
10
100
OUTPUT CURRENT (mA)
Figure 9. Ground Current vs. Output Current,
VOUT = 0.8 V
Figure 10. Ground Current vs. Output Current,
VOUT = 3.3 V
50
TA = 125°C
TA = 25°C
30
TA = −40°C
25
2.0
2.5
3.0
3.5
4.0
4.5
5.0
40
TA = 125°C
35
TA = 25°C
30
TA = −40°C
25
20
15
10
5.5
CIN = 1 mF,
COUT = 1 mF,
VOUT(NOM) = 3.3 V,
IOUT = 0 mA
45
2.0
2.5
3.0
3.5
4.0
4.5
5.0
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
Figure 11. Quiescent Current vs. Input Voltage,
VOUT = 0.8 V
Figure 12. Quiescent Current vs. Input
Voltage, VOUT = 3.3 V
220
180
160
TA = 125°C
TA = 25°C
140
120
TA = −40°C
100
80
60
40
0
25
50
5.5
120
CIN = 1 mF,
COUT = 1 mF,
VOUT(NOM) = 1.8 V
200
1000
OUTPUT CURRENT (mA)
35
20
0
160
140
20
0
1000
CIN = 1 mF,
COUT = 1 mF,
VOUT(NOM) = 0.8 V,
IOUT = 0 mA
45
20
DROPOUT VOLTAGE (mV)
GROUND CURRENT (mA)
TA = 125°C
0.001
CIN = 1 mF,
COUT = 1 mF,
VOUT = 3.3 V,
VIN = 3.6 V
180
QUIESCENT CURRENT (mA)
280
260
240
220
200
180
160
140
120
100
80
60
40
20
0
DROPOUT VOLTAGE (mV)
GROUND CURRENT (mA)
TYPICAL CHARACTERISTICS
75
100
125
150
175
100
TA = 125°C
90
TA = 25°C
80
TA = −40°C
70
60
50
40
200
CIN = 1 mF,
COUT = 1 mF,
VOUT(NOM) = 2.8 V
110
0
25
50
75
100
125
150
175 200
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
Figure 13. Dropout Voltage vs. Output Current,
VOUT = 1.8 V
Figure 14. Dropout Voltage vs. Output Current,
VOUT = 2.8 V
http://onsemi.com
5
NCP729
TYPICAL CHARACTERISTICS
0.820
CIN = 1 mF,
COUT = 1 mF,
VOUT(NOM) = 3.3 V
110
100
0.815
90
TA = 125°C
80
TA = 25°C
70
60
TA = −40°C
OUTPUT VOLTAGE (V)
DROPOUT VOLTAGE (mV)
120
50
40
0
25
50
75
100
125
150
175
VIN = 5.5 V
0.800
VIN = 2.0 V
0.795
0.790
0.780
−40 −20
200
1.820
0
20
40
60
80
100
120 140
OUTPUT CURRENT (mA)
JUNCTION TEMPERATURE (°C)
Figure 15. Dropout Voltage vs. Output Current,
VOUT = 3.3 V
Figure 16. Output Voltage vs. Temperature,
VOUT = 0.8 V
3.340
VOUT = 1.8 V,
COUT = CIN = 1 mF,
IOUT = 10 mA
3.330
1.810
VIN = 5.5 V
1.800
VIN = 2.1 V
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
1.830
1.790
1.780
3.320
VOUT = 3.3 V,
COUT = CIN = 1 mF,
IOUT = 10 mA
3.310
VIN = 5.5 V
3.300
VIN = 3.6 V
3.290
3.280
3.270
1.770
1.760
−40 −20
0
20
40
60
80
100
3.260
−40 −20
120 140
0
20
40
60
80
100
120 140
JUNCTION TEMPERATURE (°C)
JUNCTION TEMPERATURE (°C)
Figure 17. Output Voltage vs. Temperature,
VOUT = 1.8 V
Figure 18. Output Voltage vs. Temperature,
VOUT = 3.3 V
3
OUTPUT VOLTAGE DEVIATION (mV)
OUTPUT VOLTAGE DEVIATION (mV)
0.805
0.785
1.840
2
0.810
VOUT = 0.8 V,
COUT = CIN = 1 mF,
IOUT = 10 mA
VIN = 2.0 V or VOUT(NOM) + 0.3 V,
COUT = CIN = 1 mF,
IOUT = 0 mA to 200 mA
1
0
VOUT = 0.8 V
−1
VOUT = 3.3 V
−2
−3
−40 −20
0
20
40
60
80
100
120
140
6
5
VIN = 2.0 V or VOUT(NOM) + 0.3 V to 5.5 V,
COUT = CIN = 1 mF,
IOUT = 10 mA
4
3
VOUT = 0.8 V
2
1
0
−40 −20
VOUT = 3.3 V
0
20
40
60
80
100
120 140
JUNCTION TEMPERATURE (°C)
JUNCTION TEMPERATURE (°C)
Figure 19. Load Regulation vs. Temperature
Figure 20. Line Regulation vs. Temperature
http://onsemi.com
6
NCP729
TYPICAL CHARACTERISTICS
550
500
VIN = 2.0 V or VOUT(NOM) + 0.3 V,
COUT = CIN = 1 mF,
VOUT = VOUT(NOM) − 100 mV
450
SHORT CIRCUIT CURRENT (mA)
OUTPUT CURRENT LIMIT (mA)
550
VOUT(NOM) = 3.3 V
400
VOUT(NOM) = 0.8 V
350
300
−40 −20
0
20
40
60
80
100
120
VOUT(NOM) = 3.3 V
400
VOUT(NOM) = 0.8 V
350
0
20
40
60
80
100
120 140
JUNCTION TEMPERATURE (°C)
Figure 21. Output Current Limit vs.
Temperature
Figure 22. Short Circuit Current vs.
Temperature
0.14
ENABLE INPUT CURRENT (mA)
VIN = 5.5 V,
COUT = CIN = 1 mF,
VEN = 0 V
VOUT(NOM) = 3.3 V
0.6
0.4
VOUT(NOM) = 0.8 V
0.2
0
20
40
60
80
100
120
0.12
TA = 125°C
0.10
TA = 25°C
0.08
TA = −40°C
0.06
VIN = 3.6 V,
VOUT(NOM) = 3.3 V,
COUT = CIN = 1 mF,
IOUT = 10 mA
0.04
0.02
0
140
0
1
2
3
4
5
6
JUNCTION TEMPERATURE (°C)
ENABLE VOLTAGE (V)
Figure 23. Shutdown Current vs. Temperature
Figure 24. Enable Input Current vs. Enable
Voltage
1.2
2.0
VIN = 3.6 V,
VOUT = 3.3 V,
COUT = CIN = 1 mF,
IOUT = 10 mA
1.0
0.8
UVLO THRESHOLD (V)
SHUTDOWN CURRENT (mA)
450
JUNCTION TEMPERATURE (°C)
0
−40 −20
ENABLE THRESHOLD (V)
500
300
−40 −20
140
1.0
0.8
VIN = 2.0 V or VOUT(NOM) + 0.3 V,
COUT = CIN = 1 mF,
VOUT = 0 V (Shorted to GND)
VEN Rising
0.6
VEN Falling
0.4
0.2
0
−40 −20
0
20
40
60
80
100
120
1.8
VIN Rising
1.6
VIN Falling
1.4
1.2
VEN = VIN,
VOUT = 3.3 V,
COUT = CIN = 1 mF,
IOUT = 10 mA
1.0
−40 −20
140
0
20
40
60
80
100
120 140
JUNCTION TEMPERATURE (°C)
JUNCTION TEMPERATURE (°C)
Figure 25. Enable Threshold vs. Temperature
Figure 26. UVLO Threshold vs. Temperature
http://onsemi.com
7
NCP729
VIN = 3.3 V
VOUT(NOM) = 2.8 V
CIN = COUT = 1 mF
IOUT = 1 mA
TA = 25°C
0V
0V
IINRUSH
0V
VEN
0V
IINRUSH
0 mA
100 ms/DIV
Figure 27. Turn−On Response, VOUT = 2.8 V
Figure 28. Turn−On Response, VOUT = 1.8 V
VIN = 3.3 V
VOUT(NOM) = 2.8 V
CIN = COUT = 1 mF
IOUT = 1 mA
TA = 25°C
VIN = 2.3 V
VOUT(NOM) = 1.8 V
CIN = COUT = 1 mF
IOUT = 1 mA
TA = 25°C
VOUT
500 mV/DIV
1 V/DIV
0V
0V
VEN
1 V/DIV
0V
VEN
0V
2 ms/DIV
2 ms/DIV
Figure 29. Turn−Off Response, VOUT = 2.8 V
Figure 30. Turn−Off Response, VOUT = 1.8 V
100 mV/DIV
VOUT = 2.8 V
VIN = 3.3 V
VOUT(NOM) = 2.8 V
CIN = COUT = 1 mF
IOUT = 1 mA ... 200 mA
DIOUT/Dt = 200 mA/1 ms
TA = 25°C
200 mA/DIV
1 V/DIV
VOUT
100 ms/DIV
VOUT
100 mV/DIV
VIN = 2.3 V
VOUT(NOM) = 1.8 V
CIN = COUT = 1 mF
IOUT = 1 mA
TA = 25°C
IOUT = 200 mA
IOUT = 1 mA
VIN = 2.3 V
VOUT(NOM) = 1.8 V
CIN = COUT = 1 mF
IOUT = 1 mA ... 200 mA
DIOUT/Dt = 200 mA/1 ms
TA = 25°C
VOUT = 1.8 V
IOUT = 200 mA
IOUT = 1 mA
50 ms/DIV
50 ms/DIV
Figure 31. Load Transient Response, VOUT = 2.8
V,
IOUT = 1 mA to 200 mA
Figure 32. Load Transient Response, VOUT = 1.8
V,
IOUT = 1 mA to 200 mA
http://onsemi.com
8
200 mA/DIV
1 V/DIV
VEN
0 mA
200 mA/DIV
500 mV/DIV
VOUT
200 mA/DIV
1 V/DIV
1 V/DIV
TYPICAL CHARACTERISTICS
NCP729
100 mV/DIV
VIN = 3.3 V
VOUT(NOM) = 2.8 V
CIN = COUT = 1 mF
IOUT = 10 mA ... 200 mA
DIOUT/Dt = 200 mA/1 ms
TA = 25°C
VOUT = 2.8 V
VIN = 2.3 V
VOUT(NOM) = 1.8 V
CIN = COUT = 1 mF
IOUT = 10 mA ... 200 mA
DIOUT/Dt = 200 mA/1 ms
TA = 25°C
200 mA/DIV
200 mA/DIV
100 mV/DIV
TYPICAL CHARACTERISTICS
IOUT = 200 mA
IOUT = 10 mA
IOUT = 200 mA
IOUT = 10 mA
20 ms/DIV
20 ms/DIV
Figure 34. Load Transient Response, VOUT = 1.8 V,
IOUT = 10 mA to 200 mA
Figure 33. Load Transient Response, VOUT = 2.8
V,
IOUT = 10 mA to 200 mA
VIN = 3.3 V
VOUT(NOM) = 2.8 V
CIN = COUT = 1 mF
VOUT = 2.8 V to 0 V
TA = 25°C
VIN = 2.3 V
VOUT(NOM) = 1.8 V
CIN = COUT = 1 mF
VOUT = 1.8 V to 0 V
TA = 25°C
500 mV/DIV
VOUT = 1.8 V
0V
300 mA/DIV
ISHORT
1 mA
0V
ISHORT
1 mA
100 ms/DIV
Figure 35. Short−Circuit Response,
VOUT = 2.8 V
Figure 36. Short−Circuit Response,
VOUT = 1.8 V
500 mV/DIV
200 ms/DIV
VIN = 4.3 V
VIN = 3.3 V
VIN = 3.3 V
VIN = 2.3 V
40 mV/DIV
40 mV/DIV
500 mV/DIV
300 mA/DIV
1 V/DIV
VOUT = 2.8 V
VOUT = 1.8 V
VOUT = 2.8 V
VIN = 3.3 V to 4.3 V
DVIN/Dt = 1 V/1 ms
VOUT(NOM) = 2.8 V
COUT = 1 mF
IOUT = 10 mA
VOUT = 1.8 V
VIN = 2.3 V to 3.3 V
DVIN/Dt = 1 V/1 ms
VOUT(NOM) = 1.8 V
COUT = 1 mF
IOUT = 10 mA
200 ms/DIV
200 ms/DIV
Figure 37. Line Transient Response,
VOUT = 2.8 V
Figure 38. Line Transient Response,
VOUT = 1.8 V
http://onsemi.com
9
NCP729
TYPICAL CHARACTERISTICS
10
Unstable Operation Region
ESR (W)
1
VOUT = 0.8 V
VOUT = 3.3 V
0.1
Stable Operation Region
0.01
VIN = VOUT(NOM) + 0.3 V or 2 V,
COUT = CIN = 1 mF,
TA = 25°C
0.001
0
20
40
60
80
100 120 140 160 180 200
IOUT, OUTPUT CURRENT (mA)
Figure 39. ESR vs. Output Current
http://onsemi.com
10
NCP729
APPLICATIONS INFORMATION
General
Part Number
Description
C0402C105K8PACTU
1 mF Ceramic ±10%,
10 V, 0402, X5R
C1005X5R1A105K
-||-
GRM155R61A105KE15D
-||-
0402ZD105KAT2A
-||-
MCCA000571
1 mF Ceramic ±10%,
50 V, 1206, X7R
ECJ−0EB0J475M
4.7 mF Ceramic ±20%,
6.3 V, 0402, X5R
The NCP729 is a high performance 200 mA Very Low
Dropout Linear Regulator. This device delivers excellent
noise and dynamic performance. It features typical
quiescent current of 35 mA at no−load, ultra−low noise of
10 mVRMS and high PSRR of 72 dB at 1 kHz. Such excellent
dynamic parameters and small package size make the device
an ideal choice for powering the precision analog and noise
sensitive circuitry in portable applications. NCP729
requires very small voltage headroom for correct operation.
The dropout for 3.3 V voltage option is only 68 mV (typ.) A
logic EN input provides ON/OFF control of the output
voltage. When the EN is low the device consumes as low as
typ. 300 nA from the IN pin.
The device is fully protected in case of output overload,
output short circuit condition and overheating, assuring a
very robust design.
The regulator remains stable and regulates the output
voltage properly within the ±2% tolerance limits with no
external load applied to the output.
Input Capacitor (CIN)
Enable Operation
No−load Operation
It is recommended to connect a minimum of 1 mF Ceramic
X5R or X7R capacitor close to the IN pin of the device. This
capacitor will provide a low impedance path for unwanted
AC signals or noise modulated onto constant input voltage.
There is no requirement for the min./max. ESR of the
input capacitor but it is recommended to use ceramic
capacitors for their low ESR and ESL. A good input
capacitor will limit the influence of input trace inductance
and power source resistance during sudden load current
changes. Larger input capacitor may be necessary if fast and
large line/load transients are encountered in the application.
The NCP729 uses the EN pin to enable, disable its output
and to deactivate, activate the active output discharge
function.
If the EN pin voltage is <0.4 V the device is guaranteed to
be disabled. The pass transistor is turned−off and the active
discharge transistor is active so that the output voltage VOUT
is pulled to GND through a 1 kW resistor. In the disable state
the device consumes as low as typ. 300 nA from the VIN.
If the EN pin voltage > 0.9 V the device is guaranteed to
be enabled. The output voltage is regulated at the nominal
value and the active discharge transistor is turned−off.
The EN pin has internal pull−down current source with
typ. value of 110 nA which assures that the device is
turned−off when the EN pin is not connected. A build in
2 mV of hysteresis in the EN prevents from periodic on/off
oscillations that can occur due to noise.
In the case where the EN function isn’t required the EN
pin should be tied directly to IN.
Output Capacitor (COUT)
The NCP729 is designed to operate with a small 1.0 mF
ceramic capacitor on the output. To assure proper operation
it is recommended to use min. 1.0 mF capacitor with the
initial tolerance of ±10%, made of X7R or X5R dielectric
material types.
NCP729 is internally compensated so there is no
requirement for the minimum value of Equivalent Series
Resistance (ESR) for the COUT but the maximum value of
ESR should be less than 500 mW.
Larger output capacitors could be used to improve the load
transient response or high frequency PSRR. This part is not
designed to work with tantalum or electrolytic capacitors on
the output due to their large ESR and ESL. The equivalent
series resistance of tantalum capacitors is also strongly
dependent on the temperature, increasing at low
temperatures. The tantalum capacitors are generally more
costly than ceramic capacitors.
The table below lists examples of suitable output
capacitors:
Undervoltage Lockout
The internal UVLO circuitry assures that the device
becomes disabled when the VIN falls below typ. 1.5 V. When
the VIN voltage ramps−up the NCP729 becomes enabled for
VIN ≥ 1.6 V. The 100 mV hysteresis prevents from on/off
oscillations that can occur due to noise on VIN line.
Reverse Current
The PMOS pass transistor has an inherent body diode
which will be forward biased in the case that VOUT > VIN.
Due to this fact in cases where the extended reverse current
condition is anticipated the device may require additional
external protection.
http://onsemi.com
11
NCP729
Output Current Limit
Load Regulation
Output Current is internally limited within the IC to a
typical 400 mA. The NCP729 will source this amount of
current measured with the output voltage 100 mV lower than
the nominal VOUT. The short circuit current flowing to the
IN pin when the Output Voltage is directly shorted to ground
will be just slightly above 400 mA – typ. 410 mA. The
current limit and short circuit were verified to work properly
and to secure the part from the damage up to VIN = 5.5 V at
TA = 25°C. There is no limitation for the short circuit
duration.
The NCP729 features excellent load regulation of typical
200 mV in the 0 mA to 200 mA range. Due to this fact at large
load currents the major contributors to the output voltage
shift will be the junction temperature increase and the PCB
trace resistance.
Line Regulation
The IC features very good line regulation of typical
150 mV/V measured for the input voltage change from VIN
= VOUT + 0.3 V to 5.5 V.
Power Supply Rejection Ratio
Thermal Shutdown
The NCP729 features very good Power Supply Rejection
ratio. If desired the PSRR at higher frequencies in the range
100 kHz – 10 MHz can be tuned by the selection of COUT
capacitor and proper PCB layout. Additional Ferrite Bead
Input filter will further improve the PSRR.
When the die temperature exceeds the Thermal Shutdown
threshold (TSD – 165°C typical), Thermal Shutdown event
is detected and the device is disabled. The IC will remain in
this state until the die temperature decreases below the
Thermal Shutdown Reset threshold (TSDU − 140°C typical).
Once the IC temperature falls below the 140°C the LDO is
enabled. The thermal shutdown feature provides protection
from a catastrophic device failure due to accidental
overheating. This protection is not intended to be used as a
substitute for proper heat sinking.
Output Noise
The IC is designed for ultra−low noise output voltage.
Figures 3 and 4 illustrate the noise performance for different
VOUT, IOUT, COUT. Generally the noise performance in the
indicated frequency range improves with increasing output
current.
Power Dissipation
As power dissipated in the NCP729 increases, it might
become necessary to provide some thermal relief. The
maximum power dissipation supported by the device is
dependent upon board design and layout. Mounting pad
configuration on the PCB, the board material, and the
ambient temperature affect the rate of junction temperature
rise for the part.
The maximum power dissipation the IC can handle is
given by:
P D(MAX) +
ƪTJ(MAX) * TAƫ
q JA
PCB Layout Recommendations
To obtain good transient performance and good regulation
characteristics place CIN and COUT capacitors close to the
device pins and make the PCB traces wide. VOUT, VIN and
GND printed circuit board traces should be as wide as
possible. When the impedance of these traces is high, there
is a chance for noise pickup.
In order to minimize the solution size use 0402 capacitors.
Larger copper area connected to the pins will improve the
device thermal resistance. The actual power dissipation can
be calculated by the formula given in Equation 2.
(eq. 1)
The power dissipated by the NCP729 for given
application conditions can be calculated from the following
equations:
P D [ V INǒI GND@I OUTǓ ) I OUTǒV IN * V OUTǓ
(eq. 2)
Table 5. ORDERING INFORMATION
Device
Voltage Option
Marking
NCP729FC08T2G
0.8V
7AA
NCP729FC18T2G
1.8V
7AB
NCP729FC25T2G
2.5V
7AG
NCP729FC26T2G
2.6V
7AC
NCP729FC28T2G
2.8V
7AD
NCP729FC285T2G
2.85V
7AE
NCP729FC30T2G
3.0V
7AH
NCP729FC33T2G
3.3V
7AF
Package
Shipping †
CSP4
5000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
12
NCP729
PACKAGE DIMENSIONS
CSP4, 1.06x1.06
CASE 568AD
ISSUE A
ÈÈ
ÈÈ
D
PIN A1
REFERENCE
2X
A
B
E
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. COPLANARITY APPLIES TO SPHERICAL
CROWNS OF SOLDER BALLS.
DIM
A
A1
b
D
E
e
0.10 C
2X
0.10 C
TOP VIEW
0.10 C
A
4X
0.05 C
A1
SIDE VIEW
NOTE 3
MILLIMETERS
MIN
MAX
−−−
0.70
0.21
0.26
0.30
0.34
1.06 BSC
1.06 BSC
0.50 BSC
RECOMMENDED
SOLDERING FOOTPRINT*
C
SEATING
PLANE
A1
PACKAGE
OUTLINE
e/2
4X
0.05 C A B
0.03 C
e
b
e
0.50
PITCH
B
A
1
2
e/2
4X
0.50
0.275
0.25
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
BOTTOM VIEW
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
13
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP729/D
Similar pages