50 MHz to 9 GHz 65 dB TruPwr Detector ADL5902 Data Sheet FEATURES FUNCTIONAL BLOCK DIAGRAM Accurate rms-to-dc conversion from 50 MHz to 9 GHz Single-ended input dynamic range of 65 dB No balun or external input matching required Waveform and modulation independent, such as GSM/CDMA/W-CDMA/TD-SCDMA/WiMAX/LTE Linear-in-decibels output, scaled 53 mV/dB Transfer function ripple: <±0.1 dB Temperature stability: <±0.3 dB All functions temperature and supply stable Operates from 4.5 V to 5.5 V from −40°C to +125°C Power-down capability to 1.5 mW Pin-compatible with the 50 dB dynamic range AD8363 VPOS POS 3 10 TEMPERATURE SENSOR ADL5902 INHI 14 LINEAR-IN-dB VGA (NEGATIVE SLOPE) NC X2 G=5 BIAS AND POWERDOWN CONTROL VSET 6 VOUT 5 CLPF VREF 2.3V NC 13 APPLICATIONS 7 ITGT 2 NC 16 TEMP IDET X2 INLO 15 8 Power amplifier linearization/control loops Transmitter power controls Transmitter signal strength indication (TSSI) RF instrumentation 1 11 12 9 4 TADJ/PWDN VREF VTGT COMM COMM 08218-001 26pF Figure 1. GENERAL DESCRIPTION The ADL5902 is a true rms responding power detector that has a 65 dB measurement range when driven with a single-ended 50 Ω source. This feature makes the ADL5902 frequency versatile by eliminating the need for a balun or any other form of external input tuning for operation up to 9 GHz. The ADL5902 provides a solution in a variety of high frequency systems requiring an accurate measurement of signal power. Requiring only a single supply of 5 V and a few capacitors, it is easy to use and capable of being driven single-ended or with a balun for differential input drive. The ADL5902 can operate from 50 MHz to 9 GHz and can accept inputs from −62 dBm to at least +3 dBm with large crest factors, such as GSM, CDMA, W-CDMA, TD-SCDMA, WiMAX, and LTE modulated signals. The ADL5902 can determine the true power of a high frequency signal having a complex low frequency modulation envelope or can be used as a simple low frequency rms voltmeter. Used as a power measurement device, VOUT is connected to VSET. The output is then proportional to the Rev. B logarithm of the rms value of the input. In other words, the reading is presented directly in decibels and is scaled 1.06 V per decade, or 53 mV/dB; other slopes are easily arranged. In controller mode, the voltage applied to VSET determines the power level required at the input to null the deviation from the set point. The output buffer can provide high load currents. The ADL5902 has 1.5 mW power consumption when powered down by a logic high applied to the PWDN pin. It powers up within approximately 5 μs to the nominal operating current of 73 mA at 25°C. The ADL5902 is supplied in a 4 mm × 4 mm, 16-lead LFCSP for operation over the wide temperature range of −40°C to +125°C. The ADL5902 is also pin-compatible with the AD8363, 50 dB dynamic range TruPwr™ detector. This feature allows the designer to create one circuit layout for projects requiring different dynamic ranges. A fully populated RoHS-compliant evaluation board is available. Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2010–2016 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADL5902* PRODUCT PAGE QUICK LINKS Last Content Update: 02/23/2017 COMPARABLE PARTS REFERENCE MATERIALS View a parametric search of comparable parts. Product Selection Guide • RF Source Booklet EVALUATION KITS • ADL5902 Evaluation Board DESIGN RESOURCES • ADL5902 Material Declaration DOCUMENTATION • PCN-PDN Information Application Notes • Quality And Reliability • AN-1040: RF Power Calibration Improves Performance of Wireless Transmitters • Symbols and Footprints Data Sheet DISCUSSIONS • ADL5902: 50 MHz to 9 GHz 65 dB TruPwr Detector Data Sheet View all ADL5902 EngineerZone Discussions. SOFTWARE AND SYSTEMS REQUIREMENTS • BeMicro FPGA Project for CN0178 with Nios driver • CN0178 FMC-SDP Interposer & Evaluation Board / Xilinx KC705 Reference Design TOOLS AND SIMULATIONS • ADIsimPLL™ • ADIsimRF SAMPLE AND BUY Visit the product page to see pricing options. TECHNICAL SUPPORT Submit a technical question or find your regional support number. DOCUMENT FEEDBACK Submit feedback for this data sheet. REFERENCE DESIGNS • CN0178 • CN0340 • CN0360 This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified. ADL5902 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 VSET Interface ............................................................................ 18 Applications ....................................................................................... 1 Output Interface ......................................................................... 18 Functional Block Diagram .............................................................. 1 VTGT Interface .......................................................................... 19 General Description ......................................................................... 1 Basis for Error Calculations ...................................................... 19 Revision History ............................................................................... 2 Measurement Mode Basic Connections.................................. 19 Specifications..................................................................................... 3 Setting VTADJ.................................................................................. 20 Absolute Maximum Ratings............................................................ 7 Setting VTGT ................................................................................. 20 ESD Caution .................................................................................. 7 Choosing a Value for CLPF ............................................................ 20 Pin Configuration and Function Descriptions ............................. 8 Output Voltage Scaling .............................................................. 23 Typical Performance Characteristics ............................................. 9 System Calibration and Error Calculation.............................. 24 Theory of Operation ...................................................................... 15 High Frequency Performance................................................... 25 Square Law Detector and Amplitude Target .............................. 15 Low Frequency Performance .................................................... 25 RF Input Interface ...................................................................... 16 Description of Characterization ............................................... 25 Small Signal Loop Response ..................................................... 17 Evaluation Board Schematics and Artwork ................................ 26 Temperature Sensor Interface ................................................... 17 Assembly Drawings .................................................................... 27 VREF Interface ........................................................................... 17 Outline Dimensions ....................................................................... 28 Temperature Compensation Interface ..................................... 17 Ordering Guide .......................................................................... 28 Power-Down Interface ............................................................... 18 REVISION HISTORY 8/2016—Rev. A to Rev. B Changes to Figure 2 .......................................................................... 8 Updated Outline Dimensions ....................................................... 28 Changes to Ordering Guide .......................................................... 28 7/2011—Rev. 0 to Rev. A Updated Format .................................................................. Universal Changes to Measurement Mode Basic Connections Section and Figure 45 .......................................................................................... 19 Changes to Setting VTGT Section and Choosing a Value for CLPF Section ...................................................................................... 20 Changes to Output Voltage Scaling Section, Figure 49, and Table 7 .............................................................................................. 23 Changes to Figure 54 and Table 8 ................................................. 26 Changes to Figure 55 and Figure 56 ............................................. 27 4/2010—Revision 0: Initial Version Rev. B | Page 2 of 28 Data Sheet ADL5902 SPECIFICATIONS VS = 5 V, TA = 25°C, ZO = 50 Ω, single-ended input drive, RT = 60.4 Ω, VOUT connected to VSET, VTGT = 0.8 V, CLPF = 0.1 μF. Negative current values imply that the ADL5902 is sourcing current out of the indicated pin. Table 1. Parameter OVERALL FUNCTION Frequency Range RF INPUT INTERFACE Input Impedance Common Mode Voltage 100 MHz ±1.0 dB Dynamic Range Maximum Input Level, ±1.0 dB Minimum Input Level, ±1.0 dB Deviation vs. Temperature Logarithmic Slope Logarithmic Intercept 700 MHz ±1.0 dB Dynamic Range Maximum Input Level, ±1.0 dB Minimum Input Level, ±1.0 dB Deviation vs. Temperature Logarithmic Slope Logarithmic Intercept 900 MHz ±1.0 dB Dynamic Range Maximum Input Level, ±1.0 dB Minimum Input Level, ±1.0 dB Deviation vs. Temperature Logarithmic Slope Logarithmic Intercept Test Conditions/Comments Pins INHI, INLO, ac-coupled Single-ended drive, 50 MHz CW input, TA = +25°C, VTADJ = 0.5 V Calibration at −60 dBm, −45 dBm, and 0 dBm Calibration at −60 dBm, −45 dBm, and 0 dBm Deviation from output at 25°C −40°C < TA < +85°C; PIN = 0 dBm −40°C < TA < +85°C; PIN = −45 dBm −40°C < TA < +125°C; PIN = 0 dBm −40°C < TA < +125°C; PIN = −45 dBm −45 dBm < PIN < 0 dBm; calibration at −45 dBm and 0 dBm −45 dBm < PIN < 0 dBm; calibration at −45 dBm and 0 dBm CW input, TA = +25°C,VTADJ = 0.4 V Calibration at −60 dBm, −45 dBm, and 0 dBm Calibration at −60 dBm, −45 dBm, and 0 dBm Deviation from output at 25°C −40°C < TA < +85°C; PIN = 0 dBm −40°C < TA < +85°C; PIN = −45 dBm −40°C < TA < +125°C; PIN = 0 dBm −40°C < TA < +125°C; PIN = −45 dBm −45 dBm < PIN < 0 dBm; calibration at −45 dBm and 0 dBm −45 dBm < PIN < 0 dBm; calibration at −45 dBm and 0 dBm CW input, TA = +25°C, VTADJ = 0.4 V Calibration at −60 dBm, −45 dBm, and 0 dBm Calibration at −60 dBm, −45 dBm, and 0 dBm Deviation from output at 25°C −40°C < TA < +85°C; PIN = 0 dBm −40°C < TA < +85°C; PIN = −45 dBm −40°C < TA < +125°C; PIN = 0 dBm −40°C < TA < +125°C; PIN = −45 dBm −45 dBm < PIN < 0 dBm; calibration at −45 dBm and 0 dBm −45 dBm < PIN < 0 dBm; calibration at −45 dBm and 0 dBm Rev. B | Page 3 of 28 Min Typ Max Unit 50 to 9000 MHz 2000 2.5 Ω V 63 3 −60 dB dBm dBm −0.11/+0.25 −0.22/+0.15 −0.35/+0.25 −0.22/+0.15 53.8 dB dB dB dB mV/dB −62.1 dBm 61 1 −60 dB dBm dBm +0.3/−0.2 −0.1/0 +0.3/−0.4 −0.1/0 53.7 dB dB dB dB mV/dB −62.8 dBm 61 1 −60 dB dBm dBm +0.3/−0.2 0/−0.1 +0.3/−0.4 0/−0.1 53.7 dB dB dB dB mV/dB −62.7 dBm ADL5902 Parameter Deviation from CW Response 1.9 GHz ±1.0 dB Dynamic Range Maximum Input Level, ±1.0 dB Minimum Input Level, ±1.0 dB Deviation vs. Temperature Logarithmic Slope Logarithmic Intercept 2.14 GHz ±1.0 dB Dynamic Range Maximum Input Level, ±1.0 dB Minimum Input Level, ±1.0 dB Deviation vs. Temperature Logarithmic Slope Logarithmic Intercept Deviation from CW Response 2.6 GHz ±1.0 dB Dynamic Range Maximum Input Level, ±1.0 dB Minimum Input Level, ±1.0 dB Deviation vs. Temperature Logarithmic Slope Logarithmic Intercept 3.5 GHz ±1.0 dB Dynamic Range Maximum Input Level, ±1.0 dB Minimum Input Level, ±1.0 dB Data Sheet Test Conditions/Comments 11.02 dB peak-to-rms ratio (CDMA2000) 5.13 dB peak-to-rms ratio (16 QAM) 2.76 dB peak-to-rms ratio (QPSK) CW input, TA = +25°C, VTADJ = 0.4 V Calibration at −60 dBm, −45 dBm, and 0 dBm Calibration at −60 dBm, −45 dBm, and 0 dBm Deviation from output at 25°C −40°C < TA < +85°C; PIN = 0 dBm −40°C < TA < +85°C; PIN = −45 dBm −40°C < TA < +125°C; PIN = 0 dBm −40°C < TA < +125°C; PIN = −45 dBm −45 dBm < PIN < 0 dBm; calibration at −45 dBm, and 0 dBm −45 dBm < PIN < 0 dBm; calibration at −45 dBm and 0 dBm CW input, TA = +25°C, VTADJ = 0.4 V Calibration at −60 dBm, −45 dBm, and 0 dBm Calibration at −60 dBm, −45 dBm, and 0 dBm Deviation from output at 25°C −40°C < TA < +85°C; PIN = 0 dBm −40°C < TA < +85°C; PIN = −45 dBm −40°C < TA < +125°C; PIN = 0 dBm −40°C < TA < +125°C; PIN = −45 dBm −45 dBm < PIN < 0 dBm; calibration at −45 dBm and 0 dBm −45 dBm < PIN < 0 dBm; calibration at −45 dBm and 0 dBm 12.16 dB peak-to-rms ratio (four-carrier W-CDMA) 11.58 dB peak-to-rms ratio (LTE TM1 1CR 20 MHz BW) 10.56 dB peak-to-rms ratio (one-carrier W-CDMA) 6.2 dB peak-to-rms ratio (64 QAM) CW input, TA = +25°C, VTADJ = 0.45 V Calibration at −60, −45 and 0 dBm Calibration at −60, −45 and 0 dBm Deviation from output at 25°C −40°C < TA < +85°C; PIN = 0 dBm −40°C < TA < +85°C; PIN = −45 dBm −40°C < TA < +125°C; PIN = 0 dBm −40°C < TA < +125°C; PIN = −45 dBm −45 dBm < PIN < 0 dBm; calibration at −45 dBm and 0 dBm −45 dBm < PIN < 0 dBm; calibration at −45 dBm and 0 dBm CW input, TA = +25°C, VTADJ = 0.5 V Calibration at −60 dBm, −40 dBm, and 0 dBm Calibration at −60 dBm, −40 dBm, and 0 dBm Rev. B | Page 4 of 28 Min Typ −0.1 −0.05 −0.05 Max Unit dB dB dB 64 3 −61 dB dBm dBm −0.1/0 −0.3/+0.3 −0.1/0 −0.3/+0.4 52.6 dB dB dB dB mV/dB −62.6 dBm 65 3 −62 dB dBm dBm −0.1/0 −0.3/+0.3 −0.1/0 −0.3/+0.4 52.4 dB dB dB dB mV/dB −62.9 dBm −0.1 −0.1 −0.1 −0.07 dB dB dB dB 65 5 −60 dB dBm dBm 0.4/0 +0.5/−0.6 0.6/0 +0.7/−0.6 51.0 dB dB dB dB mV/dB −62.1 dBm 57 8 −49 dB dBm dBm Data Sheet Parameter Deviation vs. Temperature Logarithmic Slope Logarithmic Intercept 5.8 GHz ±1.0 dB Dynamic Range Maximum Input Level, ±1.0 dB Minimum Input Level, ±1.0 dB Deviation vs. Temperature Logarithmic Slope Logarithmic Intercept OUTPUT INTERFACE Output Swing, Controller Mode Current Source/Sink Capability Voltage Regulation Output Noise Rise Time Fall Time SETPOINT INPUT Voltage Range Input Resistance Logarithmic Scale Factor Logarithmic Intercept TEMPERATURE COMPENSATION Input Voltage Range Input Bias Current Input Resistance VOLTAGE REFERENCE Output Voltage Temperature Sensitivity Short-Circuit Current Source/ Sink Capability Voltage Regulation ADL5902 Test Conditions/Comments Deviation from output at 25°C −40°C < TA < +85°C; PIN = 0 dBm −40°C < TA < +85°C; PIN = −40 dBm −40°C < TA < +125°C; PIN = 0 dBm −40°C < TA < +125°C; PIN = −40 dBm −40 dBm < PIN < 0 dBm; calibration at −30 dBm and 0 dBm −40 dBm < PIN < 0 dBm; calibration at −30 dBm and 0 dBm Min CW input, TA = +25°C, VTADJ = 0.95 V Calibration at −50 dBm, −30 dBm, and 0 dBm Calibration at −50 dBm, −30 dBm, and 0 dBm Deviation from output at 25°C −40°C < TA < +85°C; PIN = 0 dBm −40°C < TA < +85°C; PIN = −30 dBm −40°C < TA < +125°C; PIN = 0 dBm −40°C < TA < +125°C; PIN = −30 dBm −30 dBm < PIN < 0 dBm; calibration at −30 dBm and 0 dBm −30 dBm < PIN < 0 dBm; calibration at −30 dBm and 0 dBm VOUT (Pin 6) Swing range minimum, RL ≥ 500 Ω to ground Swing range maximum, RL ≥ 500 Ω to ground Typ Max 0.2/0 −0.2/+0.4 +0.2/−0.3 −0.2/+0.4 49.6 dB dB dB dB mV/dB −63.1 dBm 61 9 −52 dB dBm dBm −0.8/0 −1.3/+0.1 −1.6/0 −1.3/+0.1 42.7 dB dB dB dB mV/dB −54.1 dBm 0.03 4.8 +0.2/−0.2 25 V V mA % nV/√Hz 3 μs 25 μs 3.5 0.23 72 52.4 −62.9 V V kΩ mV/dB dBm 10/10 ILOAD = 8 mA, source/sink RFIN = 2.14 GHz, −20 dBm, fNOISE = 100 kHz, CLPF = 220 pF Transition from no input to 1 dB settling at PIN = −10 dBm, CLPF = 220 pF Transition from −10 dBm to off (1 dB of final value), CLPF = 220 pF VSET (Pin 7) Log conformance error ≤ 1 dB, minimum 2.14 GHz Log conformance error ≤ 1 dB, maximum 2.14 GHz f = 2.14 GHz f = 2.14 GHz Pin TADJ/PWDN (Pin 1) Unit VTADJ = 0.4 V VTADJ = 0.4 V VREF (Pin 11) PIN = −55 dBm 25°C ≤ TA ≤ 125°C −15°C ≤ TA ≤ +25°C −40°C ≤ TA ≤ −15°C 25°C ≤ TA ≤ 125°C 0 2 200 V μA kΩ 2.3 −0.16 0.045 −0.04 4/0.05 V mV/°C mV/°C mV/°C mA −40°C ≤ TA < +25°C TA = 25°C, ILOAD = 2 mA 3/0.05 −0.4 mA % Rev. B | Page 5 of 28 VS ADL5902 Parameter TEMPERATURE REFERENCE Output Voltage Temperature Coefficient Short-Circuit Current Source/ Sink Capability Voltage Regulation RMS TARGET INTERFACE Input Voltage Range Input Bias Current Input Resistance POWER-DOWN INTERFACE Voltage Level to Enable Voltage Level to Disable Input Current Enable Time Disable Time POWER SUPPLY INTERFACE Supply Voltage Quiescent Current Power-Down Current Data Sheet Test Conditions/Comments TEMP (Pin 8) TA = 25°C, RL ≥ 10 kΩ −40°C ≤ TA ≤ +125°C, RL ≥ 10 kΩ 25°C ≤ TA ≤ 125°C Min −40°C ≤ TA < +25°C TA = 25°C, ILOAD = 1 mA VTGT (Pin 12) Typ V mV/°C mA 3/0.05 −2.8 mA % 2.5 V μA kΩ 4 1 500 3 5 V V μA μA μA μs 3 μs 8 100 Pin TADJ/PWDN (Pin 1) VPWDN decreasing VPWDN increasing VPWDN = 5 V VPWDN = 4.5 V VPWDN = 0 V VTADJ low to VOUT at 1 dB of final value, CLPA/B = 220 pF, PIN = 0 dBm VTADJ high to VOUT at 1 dB of final value, CLPA/B = 220 pF, PIN = 0 dBm VPOS (Pin 3, Pin 10) 4.9 4.5 TA = 25°C, PIN < −60 dBm TA = 125°C, PIN < −60 dBm VTADJ > VS − 0.1 V Rev. B | Page 6 of 28 Unit 1.4 4.9 4/0.05 0.2 VTGT = 0.8 V Max 5 73 90 300 5.5 V mA mA μA Data Sheet ADL5902 ABSOLUTE MAXIMUM RATINGS Table 2. Parameter Supply Voltage, VPOS Input Average RF Power1 Equivalent Voltage, Sine Wave Input Internal Power Dissipation θJC2 θJB2 θJA2 ΨJT2 ΨJB2 Maximum Junction Temperature Operating Temperature Range Storage Temperature Range Lead Temperature (Soldering, 60 sec) 1 2 Rating 5.5 V 21 dBm 2.51 V p-p 550 mW 10.6°C/W 35.3°C/W 57.2°C/W 1.0°C/W 34°C/W 150°C −40°C to +125°C −65°C to +150°C 300°C Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. ESD CAUTION This is for long durations. Excursions above this level, with durations much less than 1 second, are possible without damage. No airflow with the exposed pad soldered to a 4-layer JEDEC board. Rev. B | Page 7 of 28 ADL5902 Data Sheet 13 NC 14 INHI 16 NC PIN 1 INDICATOR 15 INLO PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 12 VTGT TADJ/PWDN 1 VPOS 3 ADL5902 TOP VIEW (Not to Scale) 10 VPOS VSET 7 COMM TEMP 8 CLPF 5 9 VOUT 6 COMM 4 11 VREF NOTES 1. NC = NO CONNECT. 2. THE EXPOSED PAD IS COMM AND SHOULD HAVE BOTH A GOOD THERMAL AND GOOD ELECTRICAL CONNECTION TO GROUND. 08218-002 NC 2 Figure 2. Pin Configuration Table 3. Pin Function Descriptions Pin No. 1 Mnemonic TADJ/PWDN 2 3, 10 NC VPOS 4, 9, EPAD COMM 5 CLPF 6 VOUT 7 VSET 8 11 12 TEMP VREF VTGT 13 14 NC INHI 15 INLO 16 NC Description This is a dual function pin used for controlling the amount of nonlinear intercept temperature compensation at voltages <2.5 V and/or for shutting down the device at voltages >4 V. If the shutdown function is not used, this pin can be connected to the VREF pin through a voltage divider. See Figure 41 for an equivalent circuit. No Connect. Do not connect this pin. Supply for the Device. Connect this pin to a 5 V power supply. Pin 3 and Pin 10 are not internally connected; therefore, both must connect to the source. System Common Connection. Connect these pins via low impedance to system common. The exposed paddle is also COMM and must have both a good thermal and good electrical connection to ground. Connection for RMS Averaging Capacitor. Connect a ground-referenced capacitor to this pin. A resistor can be connected in series with this capacitor to modify loop stability and response time. See Figure 43 for an equivalent circuit. Output. In measurement mode, this pin is connected to VSET. In controller mode, this pin can drive a gain control element. See Figure 43 for an equivalent circuit. The voltage applied to this pin sets the decibel value of the required RF input voltage that results in zero current flow in the loop integrating capacitor pin, CLPF. This pin controls the variable gain amplifier (VGA) gain such that a 50 mV change in VSET changes the gain by approximately 1 dB. See Figure 42 for an equivalent circuit. Temperature Sensor Output of 1.4 V at 25°C with a Coefficient of 5 mV/°C. See Figure 38 for an equivalent circuit. General-Purpose Reference Voltage Output of 2.3 V at 25°C. See Figure 39 for an equivalent circuit. The voltage applied to this pin determines the target power at the input of the RF squaring circuit. The intercept voltage is proportional to the voltage applied to this pin. The use of a lower target voltage increases the crest factor capacity; however, this can affect the system loop response. See Figure 44 for an equivalent circuit. No Connect. Do not connect this pin. RF Input. The RF input signal is normally ac-coupled to this pin through a coupling capacitor. See Figure 37 for an equivalent circuit. RF Input Common. This pin is normally ac-coupled to ground through a coupling capacitor. See Figure 37 for an equivalent circuit. No Connect. Do not connect this pin. Rev. B | Page 8 of 28 Data Sheet ADL5902 TYPICAL PERFORMANCE CHARACTERISTICS VS = 5 V, ZO = 50 Ω, single-ended input drive, VOUT connected to VSET, VTGT = 0.8 V, CLPF = 0.1 μF, TA = +25°C (black), −40°C (blue), +85°C (red), +125°C (orange) where appropriate. Error referred to the best fit line (linear regression) from − 10 dBm to − 40 dBm, unless otherwise indicated. Input RF signal is a sine wave (CW), unless otherwise indicated. 5 5.5 4 5.0 4 3 4.5 3 4.0 2 3.5 1 3.0 0 2.5 –1 2.0 –2 3.0 0 2.5 –1 2.0 –2 1.5 –3 1.5 –3 1.0 –4 1.0 –4 0.5 –5 0.5 –5 –20 –10 0 10 Figure 3. Typical VOUT and Log Conformance Error with Respect to 25°C Ideal Line over Temperature vs. Input Amplitude at 100 MHz, CW 6.0 –50 –40 –30 –20 –10 0 –6 10 08218-006 –30 PIN (dBm) Figure 6. Distribution of Error with Respect to 25°C over Temperature vs. Input Amplitude, CW, Frequency = 100 MHz 5.5 5.0 4 5.0 4 4.5 3 4.5 3 4.0 2 4.0 2 3.5 1 3.5 1 3.0 0 3.0 0 2.5 –1 2.5 –1 2.0 –2 2.0 –2 1.5 –3 1.5 –3 1.0 –4 1.0 –4 0.5 –5 0.5 –5 –50 –40 –30 –20 –10 0 10 –6 PIN (dBm) Figure 4. Typical VOUT and Log Conformance Error with Respect to 25°C Ideal Line over Temperature vs. Input Amplitude at 700 MHz, CW 6.0 6 VTADJ = 0.4V REPRESENTS 55 DEVICES FROM 2 LOTS 0 –60 08218-004 0 –60 OUTPUT VOLTAGE (V) 6.0 5 TADJ = 0.4V CALIBRATION AT 0dBm, –45dBm, AND –60dBm ERROR (dB) 6 5.5 –50 –40 –30 –20 5 –10 0 10 –6 PIN (dBm) Figure 7. Distribution of Error with Respect to 25°C over Temperature vs. Input Amplitude, CW, Frequency = 700 MHz 5.5 5.0 4 5.0 4 4.5 3 4.5 3 4.0 2 4.0 2 3.5 1 3.5 1 3.0 0 3.0 0 2.5 –1 2.5 –1 2.0 –2 2.0 –2 1.5 –3 1.5 –3 1.0 –4 1.0 –4 0.5 –5 0.5 –5 –50 –40 –30 –20 PIN (dBm) –10 0 –6 10 08218-005 0 –60 OUTPUT VOLTAGE (V) 6.0 5 TADJ = 0.4V CALIBRATION AT 0dBm, –45dBm, AND –60dBm ERROR (dB) 6 5.5 Figure 5. Typical VOUT and Log Conformance Error with Respect to 25°C Ideal Line over Temperature vs. Input Amplitude at 900 MHz, CW ERROR (dB) –40 0 –60 08218-007 –50 –6 ERROR (dB) 1 ERROR (dB) 2 PIN (dBm) OUTPUT VOLTAGE (V) 5 3.5 0 –60 OUTPUT VOLTAGE (V) 6 VTADJ = 0.5V REPRESENTS 55 DEVICES FROM 2 LOTS 4.0 08218-003 OUTPUT VOLTAGE (V) 4.5 6.0 6 VTADJ = 0.4V REPRESENTS 55 DEVICES FROM 2 LOTS 0 –60 –50 –40 –30 –20 PIN (dBm) 5 –10 0 –6 10 ERROR (dB) 5.0 6 08218-008 5.5 TADJ = 0.5V CALIBRATION AT 0dBm, –45dBm, AND –60dBm OUTPUT VOLTAGE (V) 6.0 Figure 8. Distribution of Error with Respect to 25°C over Temperature vs. Input Amplitude, CW, Frequency = 900 MHz Rev. B | Page 9 of 28 ADL5902 Data Sheet 5.5 5.0 4 5.0 4 4.5 3 4.5 3 4.0 2 4.0 2 3.5 1 3.5 1 3.0 0 3.0 0 2.5 –1 2.5 –1 2.0 –2 2.0 –2 1.5 –3 1.5 –3 1.0 –4 1.0 –4 0.5 –5 0.5 –5 0 PIN (dBm) Figure 9. Typical VOUT and Log Conformance Error with Respect to 25°C Ideal Line over Temperature vs. Input Amplitude at 1.9 GHz, CW 6.0 5.0 4.0 1.0 0.5 4 3 3 4.0 2 3.5 1 3.0 0 2.5 –1 2.0 –2 –3 1.5 –3 –4 1.0 –4 0.5 –5 –40 –30 –20 –10 0 –6 10 Figure 10. Typical VOUT and Log Conformance Error with Respect to 25°C Ideal Line over Temperature vs. Input Amplitude at 2.14 GHz, CW 6.0 TADJ = 0.45V CALIBRATION AT 0dBm, –45dBm, AND –60dBm 5.0 4.0 1.0 0.5 0 –60 –50 –40 –30 –20 PIN (dBm) –10 0 0 10 Figure 13. Distribution of Error with Respect to 25°C over Temperature vs. Input Amplitude, CW, Frequency = 2.14 GHz 5.0 4 3 4.5 3 4.0 2 3.5 1 3.0 0 2.5 –1 2.0 –2 –3 1.5 –3 –4 1.0 –4 –5 0.5 –5 –6 10 ERROR (dB) Figure 11. Typical VOUT and Log Conformance Error with Respect to 25°C Ideal Line over Temperature vs. Input Amplitude at 2.6 GHz, CW ERROR (dB) –6 4 –2 1.5 –10 5.5 –1 2.0 –20 5 0 2.5 –30 6.0 1 3.0 –40 6 2 3.5 –50 5 PIN (dBm) 6 VTADJ = 0.45V REPRESENTS 55 DEVICES FROM 2 LOTS 0 –60 08218-011 OUTPUT VOLTAGE (V) 4.5 VTADJ = 0.4V REPRESENTS 55 DEVICES FROM 2 LOTS 0 –60 OUTPUT VOLTAGE (V) –50 6 4.5 PIN (dBm) 5.5 Figure 12. Distribution of Error with Respect to 25°C over Temperature vs. Input Amplitude, CW, Frequency = 1.9 GHz –5 0 –60 –6 4 –2 1.5 10 5.0 –1 2.0 0 5 0 2.5 –10 5.5 1 3.0 –20 6.0 2 3.5 –30 6 ERROR (dB) OUTPUT VOLTAGE (V) 4.5 –40 PIN (dBm) 08218-010 5.5 TADJ = 0.4V CALIBRATION AT 0dBm, –45dBm, AND –60dBm –50 08218-012 –10 ERROR (dB) –20 08218-013 –30 5 –50 –40 –30 –20 PIN (dBm) 5 –10 0 10 ERROR (dB) –40 6 VTADJ = 0.4V REPRESENTS 55 DEVICES FROM 2 LOTS 0 –60 OUTPUT VOLTAGE (V) –50 –6 10 08218-009 OUTPUT VOLTAGE (V) 0 –60 OUTPUT VOLTAGE (V) 6.0 5 TADJ = 0.4V CALIBRATION AT 0dBm, –45dBm, AND –60dBm ERROR (dB) 6 5.5 –6 08218-014 6.0 Figure 14. Distribution of Error with Respect to 25°C over Temperature vs. Input Amplitude, CW, Frequency = 2.6 GHz Rev. B | Page 10 of 28 Data Sheet 6.0 5 5.5 5.0 4 5.0 4 4.5 3 4.5 3 4.0 2 4.0 2 3.5 1 3.5 1 3.0 0 3.0 0 2.5 –1 2.5 –1 2.0 –2 2.0 –2 1.5 –3 1.5 –3 1.0 –4 1.0 –4 0.5 –5 0.5 –5 –20 –10 0 PIN (dBm) Figure 15. Typical VOUT and Log Conformance Error with Respect to 25°C Ideal Line over Temperature vs. Input Amplitude at 3.5 GHz, CW TADJ = 0.95V CALIBRATION AT 0dBm, –30dBm, AND –50dBm –30 –20 –10 0 3.0 4 5 2.5 4 1.5 –1 –2 1.0 OUTPUT VOLTAGE (V) 0 ERROR (dB) 2 2.0 1 0 1.5 –1 1.0 –2 –3 –3 0.5 –4 0.5 –4 –5 –5 –50 –40 –30 –20 –10 –6 10 0 0 –60 08218-016 0 –60 PIN (dBm) Figure 16. Typical VOUT and Log Conformance Error with Respect to 25°C Ideal Line over Temperature vs. Input Amplitude at 5.8 GHz, CW –30 –20 –10 0 10 –6 PIN (dBm) 350 REPRESENTS 1900 PARTS FROM 3 LOTS 300 300 250 250 COUNT 200 150 200 150 100 100 50 50 0 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 VOUT (V) 3.05 08218-017 COUNT –40 Figure 19. Distribution of Error with Respect to 25°C over Temperature vs. Input Amplitude, CW, Frequency = 5.8 GHz REPRESENTS 1900 PARTS FROM 3 LOTS 350 –50 0 0.20 0.25 0.30 0.35 0.40 0.45 VOUT (V) Figure 20. Distribution of VOUT, PIN = −60 dBm, 900 MHz Figure 17. Distribution of VOUT, PIN = −10 dBm, 900 MHz Rev. B | Page 11 of 28 0.50 08218-020 OUTPUT VOLTAGE (V) 3 2 1 ERROR (dB) 6 VTADJ = 0.95V REPRESENTS 55 DEVICES FROM 2 LOTS 3 2.0 –6 10 Figure 18. Distribution of Error with Respect to 25°C over Temperature vs. Input Amplitude, CW, Frequency = 3.5 GHz 5 2.5 –40 PIN (dBm) 6 3.0 –50 08218-018 –30 0 –60 5 ERROR (dB) –40 –6 10 6 VTADJ = 0.5V REPRESENTS 55 DEVICES FROM 2 LOTS 08218-019 –50 ERROR (dB) OUTPUT VOLTAGE (V) 0 –60 OUTPUT VOLTAGE (V) 6 TADJ = 0.5V CALIBRATION AT 0dBm, –40dBm, AND –60dBm 5.5 08218-115 6.0 ADL5902 4 5.0 3 4.5 2 3.5 1 3.0 0 2.5 –1 2.0 –2 1.5 6 VOUT CW PEP = 0dB VOUT 64 QAM PEP = 6.2dB VOUT 1CR W-CDMA PEP = 10.56dB VOUT 4CR W-CDMA VOUT LTE TM1 1CR 20MHz PEP = 11.58dB ERROR CW ERROR 64 QAM ERROR 1CR W-CDMA ERROR 4CR W-CDMA ERROR LTE TM1 1CR 20MHz 4.0 3.5 5 4 3 2 1 3.0 0 2.5 –1 2.0 –2 –3 1.5 –3 1.0 –4 1.0 –4 0.5 –5 0.5 –5 –50 –40 –30 –20 –10 0 10 –6 PIN (dBm) Figure 21. Error from CW Linear Reference vs. Signal Modulation, Frequency = 900 MHz, CLPF = 0.1μF, Three-Point Calibration at 0 dBm, −45 dBm, and −60 dBm RF ENVELOPE 0dBm –10dBm –20dBm –30dBm –40dBm 5 4 3 2 0 1 2 3 4 5 6 7 8 9 –20 –10 0 10 –6 RF ENVELOPE 0dBm –10dBm –20dBm –30dBm –40dBm 4 3 2 Figure 22. Output Response to RF Burst Input, Carrier Frequency 2.14 GHz, CLPF = 220 pF, Rising Edge 5 RF ENVELOPE 0dBm –10dBm 6 5 3 2 1 8 12 16 20 24 28 32 36 RF ENVELOPE 0dBm –10dBm –20dBm –30dBm –40dBm 4 3 2 1 0 200 400 600 800 1000 1200 1400 1600 1800 TIME (µs) 0 08218-028 0 –200 4 Figure 25. Output Response to RF Burst Input, Carrier Frequency 2.14 GHz, CLPF = 220 pF, Falling Edge –20dBm –30dBm –40dBm 4 0 TIME (µs) OUTPUT VOLTAGE (V) 6 0 –4 08218-027 –1 TIME (µs) OUTPUT VOLTAGE (V) –30 1 1 0 –40 Figure 24. Error from CW Linear Reference vs. Signal Modulation, Frequency = 2.14 GHz, CLPF = 0.1 μF, Three-Point Calibration at −10 dBm, −45 dBm, and −60 dBm OUTPUT VOLTAGE (V) 5 –50 PIN (dBm) 6 6 OUTPUT VOLTAGE (V) 0 –60 08218-124 0 –60 08218-030 4.0 5.5 08218-121 OUTPUT VOLTAGE (V) 4.5 6.0 5 Figure 23. Output Response to RF Burst Input, Carrier Frequency 2.14 GHz, CLPF = 0.1 μF, Rising Edge –2000 0 2000 4000 6000 8000 10,000 12,000 14,000 16,000 18,000 TIME (µs) 08218-031 5.0 6 OUTPUT VOLTAGE (V) VOUT CW PEP = 0dB VOUT QPSK PEP = 2.76 VOUT 16 QAM PEP = 5.13 VOUT CDMA2000 PEP = 11.02 ERROR CW ERROR QPSK ERROR 16 QAM ERROR CDMA2000 5.5 ERROR (dB) 6.0 Data Sheet ERROR (dB) ADL5902 Figure 26. Output Response to RF Burst Input, Carrier Frequency 2.14 GHz, CLPF = 0.1 μF, Falling Edge Rev. B | Page 12 of 28 Data Sheet ADL5902 REPRESENTS 1900 PARTS FROM 3 LOTS 2.5 2.5 2.3 2.0 2.1 1.5 1.9 1.0 1.7 0.5 1.5 0 1.3 –0.5 1.1 –1.0 0.9 –1.5 0.7 –2.0 200 100 1.32 1.35 1.38 1.41 1.44 1.47 1.50 VTEMP VOLTAGE (V) 0.5 –55 08218-033 0 1.29 –15 5 25 45 65 85 105 125 –2.5 TEMPERATURE (°C) Figure 27. Distribution of VTEMP Voltage at 25°C, No RF Input Figure 30. VTEMP and Linearity Error with Respect to Straight Line vs. Temperature for Typical Device 0.2 REPRESENTS 1900 PARTS FROM 3 LOTS 400 CHANGE IN VREF (mV) 0 300 COUNT –35 08218-036 VTEMP (V) COUNT 300 ERROR (°C) 400 200 –0.2 –0.4 –0.6 100 2.22 2.25 2.28 2.31 2.34 2.37 2.40 2.43 VREF BIAS VOLTAGE (V) –1.0 –50 08218-034 0 2.19 –40 –30 –20 –10 0 10 20 PIN (dBm) 08218-035 –0.8 Figure 31. Change in VREF vs. Input Amplitude with Respect to −40 dBm, 25°C, Typical Device Figure 28. Distribution of VREF Voltage at 25°C, No RF Input 40 100 30 0 –10 –20 10 VPWDN DECREASING 1 VPWDN INCREASING –30 –40 –55 –35 –15 5 25 45 65 85 105 125 TEMPERATURE (°C) 0.1 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 VPWDN (V) Figure 32. Supply Current vs. VPWDN Figure 29. Change in VREF vs. Temperature with Respect to 25°C, RF Input = −40 dBm, Typical Device Rev. B | Page 13 of 28 4.8 4.9 5.0 08218-038 SUPPLY CURRENT (mA) 10 08218-037 CHANGE IN VREF (mV) 20 ADL5902 Data Sheet 200 7 180 NOISE SPECTRAL DENSITY (nV/√Hz) 6 4 0dBm 3 –10dBm –20dBm 2 –30dBm –40dBm 1 4 8 12 16 20 24 28 32 Figure 33. Output Response Using Power-Down Mode for Various RF Input Levels Carrier Frequency 2.14 GHz, CLPF = 220 pF 120 100 80 60 40 0 100 2.5 –10dBm 2.0 –30dBm 1.0 1 2 3 4 5 6 FREQUENCY (GHz) 7 8 9 08218-026 0.5 0 10k 100k 1M 10M Figure 35. Noise Spectral Density of VOUT, RF Input = −20 dBm, All CLPF Values 3.0 1.5 1k FREQUENCY (Hz) 3.5 VOUT (V) 140 08218-039 0 TIME (µs) 0 160 20 0 –4 08218-032 OUTPUT VOLTAGE (V) TADJ/PWDN PULSE 5 Figure 34. Typical VOUT vs. Frequency for Two RF Input Amplitudes, 50 MHz to 9 GHz Rev. B | Page 14 of 28 Data Sheet ADL5902 THEORY OF OPERATION The VGA output is The ADL5902 is a 50 MHz to 9 GHz true rms responding detector with a 65 dB measurement range at 2.14 GHz and a greater than 56 dB measurement range at frequencies up to 6 GHz. It incorporates a modified AD8362 architecture that increases the frequency range and improves measurement accuracy at high frequencies. Transfer function peak-to-peak ripple is reduced to <±0.1 dB over the entire dynamic range. Temperature stability of the rms output measurements provides <±0.3 dB error, typically, over the specified temperature range of −40°C to 125°C through proprietary techniques. The device accurately measures waveforms that have a high peak-to-rms ratio (crest factor). VSIG = GSET × RFIN = GO × RFIN e The output of the VGA, VSIG, is applied to a wideband square law detector. The detector provides the true rms response of the RF input signal, independent of waveform. The detector output, ISQR, is a fluctuating current with positive mean value. The difference between ISQR and an internally generated current, ITGT, is integrated by the parallel combination of CF and the external capacitor attached to the CLPF pin at the summing node. CF is an on-chip 26 pF filter capacitor, and CLPF, the external capacitance connected to the CLPF pin, can arbitrarily increase the averaging time while trading off with the response time. When the AGC loop is at equilibrium Mean(ISQR) = ITGT The nomenclature used in this data sheet to distinguish between a pin name and the signal on that pin is as follows: Mean(VSIG2) = VTGT2 (4) where VTGT is the voltage presented at the VTGT pin. This pin can conveniently be connected to the VREF pin through a voltage divider to establish a target rms voltage, VATG, of ~40 mV rms when VTGT = 0.8 V. SQUARE LAW DETECTOR AND AMPLITUDE TARGET Because the square law detectors are electrically identical and well matched, process and temperature dependent variations are effectively cancelled. The VGA gain has the form (V SET / VGNS ) (3) This equilibrium occurs only when The pin name is all uppercase, for example, VPOS, COMM, and VOUT. The signal name or a value associated with that pin is the pin mnemonic with a partial subscript, for example, CLPF and VOUT. GSET = GO e (1) where: GO is the basic fixed gain. VGNS is a scaling voltage that defines the gain slope (the decibel change per voltage). The gain decreases with increasing VSET. VPOS CH (INTERNAL) INHI VGA VSIG X2 (2) where RFIN is the ac voltage applied to the input terminals of the ADL5902. The ADL5902 consists of a high performance AGC loop. As shown in Figure 36, the AGC loop comprises a wide bandwidth variable gain amplifier (VGA), square law detectors, an amplitude target circuit, and an output driver. For a more detailed description of the functional blocks, see the AD8362 data sheet. (V SET / VGNS ) SUMMING NODE ISQR ITGT VATG = VTGT 20 X2 VTGT INLO GSET CLPF VSET CLPF (EXTERNAL) CF (INTERNAL) VOUT TADJ/PWDN TEMPERATURE SENSOR TEMP (1.4V) BAND GAP REFERENCE VREF (2.3V) Figure 36. Simplified Architecture Details Rev. B | Page 15 of 28 08218-040 COMM TEMPERATURE COMPENSATION AND BIAS ADL5902 Data Sheet When forcing the previous identity by varying the VGA setpoint, it is apparent that RMS(VSIG) = √(Mean(VSIG2)) = √(VATG2) = VATG (5) Substituting the value of VSIG from Equation 2 results in RMS(G0 × RFIN e (V SET / VGNS ) ) = VATG (6) When connected as a measurement device, VSET = VOUT. Solving for VOUT as a function of RFIN, VOUT = VSLOPE × log10(RMS(RFIN)/VZ) (7) where: VSLOPE is 1.06 V/decade (or 53 mV/dB) at 2.14 GHz. VZ is the intercept voltage. When RMS(RFIN) = VZ, this implies that VOUT = 0 V because log10(1) = 0. This makes the intercept the input that forces VOUT = 0 V if the ADL5902 had no sensitivity limit. The PINTERCEPT (in decibels relative to 1 milliwatt, that is, dBm) corresponding to Vz (in volts) in ADL5902 is given by the following equation: PINTERCEPT = −(VPEDISTAL/VSLOPE) + PMINDET (8) where VPEDISTAL is the VSET interface pedestal voltage, and PMINDET is the minimum detectable signal in decibels relative to 1 milliwatt, given by the following expression: PMINDET = dBm (VATG) – GO RF INPUT INTERFACE Figure 37 shows the RF input connections within the ADL5902. The input impedance is set primarily by an internal 2 kΩ resistor connected between INHI and INLO. A dc level of approximately half the supply voltage on each pin is established internally. Either the INHI or INLO pin can be used as the single-ended RF input pin. Signal coupling capacitors must be connected from the input signal to the INHI and INLO pins. A single external 60.4 Ω resistor to ground from the desired input creates an equivalent 50 Ω impedance over a broad section of the operating frequency range. The other input pin must be RF ac-coupled to common (ground). The input signal high-pass corner formed by the input coupling capacitor internal and external resistances is fHIGHPASS = 1/(2 × π × 50 × C) where C is the capacitance in farads and fHIGHPASS is in hertz. The input coupling capacitors must be large enough in value to pass the input signal frequency of interest and determine the low end of the frequency response. INHI and INLO can also be driven differentially using a balun. VBIAS VPOS ESD (9) where dBm(VATG) is the equivalent power in decibels relative to 1 milliwatt corresponding to a given VTGT. (11) ESD 2kΩ 2kΩ INHI INLO LOAD Combining Equation 8 and Equation 9 results in (10) ESD For the ADL5902, VPEDISTAL is approximately 0.275 V and VATG is given by VTGT/20. GO is 45 dB below approximately 4 GHz and then decreases at higher frequencies. VTGT = 0.8 V; therefore, COMM VATG = 40 mV ESD ESD ESD ESD ESD ESD ESD ESD ESD ESD 08218-041 PINTERCEPT = −(VPEDISTAL/VSLOPE) + dBm (VATG) – GO Figure 37. RF Inputs and dBm (VATG) = 10 log10((40 mV)2/50 Ω)/1 mW) ≈ −14.9 dBm Extensive ESD protection is employed on the RF inputs, and this protection limits the maximum possible input to the ADL5902. At 2.14 GHz, VSLOPE ≈ 53 mV/dB and GO at 2.14 GHz = 45 dB. This results in a PINTERCEPT ≈ −65 dBm. This differs slightly from the value in Table 1 due to the choice of calibration points and the slight nonideality of the response. In most applications, the AGC loop is closed through the setpoint interface and the VSET pin. In measurement mode, VOUT is directly connected to VSET (see the Measurement Mode Basic Connections section for more information). In controller mode, a control voltage is applied to VSET, and the VOUT pin typically drives the control input of an amplification or attenuation system. In this case, the voltage at the VSET pin forces a signal amplitude at the RF inputs of the ADL5902 that balances the system through feedback. Rev. B | Page 16 of 28 Data Sheet ADL5902 SMALL SIGNAL LOOP RESPONSE VREF INTERFACE The ADL5902 uses a VGA in a loop to force a squared RF signal to be equal to a squared dc voltage. This nonlinear loop can be simplified and solved for a small signal loop response. The lowpass corner pole is given by The VREF pin provides an internally generated voltage reference for the user. The VREF voltage is a temperature stable 2.3 V reference that is capable of sourcing 4 mA and sinking 50 μA maximum. An external resistor can be connected from VREF to COMM to provide additional current sink capability. The voltage on this pin can drive the TADJ/PWDN and VTGT pins. FreqLP ≈ 1.83 × ITGT/(CLPF) (12) where: ITGT is in amperes. CLPF is in farads. FreqLP is in hertz. VPOS INTERNAL VOLTAGE VREF ITGT is derived from VTGT; however, ITGT is a squared value of VTGT multiplied by a transresistance, namely 16kΩ (13) COMM gm is approximately 18.9 μs; therefore, with VTGT equal to the typically recommended 0.8 V, ITGT is approximately 12 μA. The value of this current varies with temperature; therefore, the small signal pole varies with temperature. However, because the RF squaring circuit and dc squaring circuit track with temperature, there is no temperature variation contribution to the absolute value of VOUT. For CW signals, FreqLP ≈ 67.7 × 10−6/(CLPF) (14) However, signals with large crest factors include low pseudorandom frequency content that must be either filtered out or sampled and averaged out (see the Choosing a Value for CLPF section for more information). TEMPERATURE SENSOR INTERFACE The ADL5902 provides a temperature sensor output with a scaling factor of the output voltage of approximately 4.9 mV/°C. The output is capable of sourcing 4 mA and sinking 50 μA maximum at 25°C. An external resistor can be connected from TEMP to COMM to provide additional current sink capability. The typical output voltage at 25°C is approximately 1.4 V. VPOS INTERNAL VPAT TEMP 12kΩ COMM 08218-042 4kΩ 08218-143 ITGT = gm × V 2 TGT Figure 39. VREF Interface Simplified Schematic TEMPERATURE COMPENSATION INTERFACE While the ADL5902 has a highly stable measurement output with respect to temperature using proprietary techniques, for optimal performance, the output temperature drift must be compensated for using the TADJ pin. The absolute value of compensation varies with frequency and VTGT. Table 4 shows the recommended voltages for VTADJ to maintain a temperature drift error of typically ±0.5 dB or better over the intended temperature range (−40°C < TA < +85°C) when driven single-ended and VTGT = 0.8 V. Table 4. Recommended VTADJ for Selected Frequencies Frequency 100 MHz 700 MHz 900 MHz 1.9 GHz 2.14 GHz 2.6 GHz 3.5 GHz 5.8 GHz VTADJ (V) 0.5 0.4 0.4 0.4 0.4 0.45 0.5 0.95 R9 in Figure 54 (Ω) 1430 1430 1430 1430 1430 1430 1430 1430 R12 in Figure 54 (Ω) 402 301 301 301 301 348 402 1007 The values in Table 4 are chosen to give the best drift performance at the high end of the usable dynamic range over the −40°C to +85°C temperature range. There is often a trade off in setting values, and optimizing for one area of the dynamic range can mean less than optimal drift performance at other input amplitudes. Figure 38. TEMP Interface Simplified Schematic Rev. B | Page 17 of 28 ADL5902 Data Sheet Compensating the device for temperature drift using TADJ allows for great flexibility. If the user requires minimum temperature drift at a given input power, a subset of the dynamic range, or even over a different temperature range than shown in this data sheet, the VTADJ can be swept while monitoring VOUT over the temperature at the frequency and amplitude of interest. The optimal VTADJ to achieve minimum temperature drift at a given power and frequency is the value of VTADJ where the output has minimum movement. ~4.5 V (or ~VS − 0.5 V), the TADJ/PWDN pin sinks approximately 500 μA. The source used to disable the ADL5902 must have a sufficiently high current capability for this reason. Figure 33 shows the typical response times for various RF input levels. The output reaches within 0.1 dB of the steady-state value in approximately 5 μs; however, the reference voltage is available to full accuracy in a much shorter time. This wake-up response varies depending on the input coupling and CLPF. VPOS 2.83 ESD 2.81 SHUTDOWN POWER-UP CIRCUIT CIRCUIT +105°C TADJ/ PWDN VOUT (V) +85°C 200Ω INTERCEPT TEMPERATURE COMPENSATION ESD 0°C 2.77 VREF 200Ω +25°C ESD 7kΩ 200Ω +55°C 2.79 7kΩ 08218-076 +125°C COMM –20°C Figure 41. TADJ/PWDN Interface Simplified Schematic –40°C VSET INTERFACE 2.73 0.1 The VSET interface has a high input impedance of 72 kΩ. The voltage at VSET is converted to an internal current used to set the internal VGA gain. The VGA attenuation control is approximately 19 dB/V. 0.3 0.4 0.5 VTADJ (V) 0.6 0.7 0.8 Figure 40. Effect of VTADJ at Various Temperatures, 2.14 GHz, −10 dBm GAIN ADJUST Varying VTADJ has only a very slight effect on VOUT at device temperatures near 25°C; however, the compensation circuit has more and more effect as the temperature departs farther from 25°C. VSET 54kΩ 18kΩ The TADJ pin has a high input impedance and can be conveniently driven from an external source or from an attenuated value of VREF using a resistor divider. Table 4 gives suggested voltage divider values to generate the required voltage from VREF. The resistors are shown in the evaluation board schematic (see Figure 54). VREF does change slightly with temperature and also input RF amplitude; however, the amount of change is unlikely to result in a significant effect on the final temperature stability of the RF measurement system. Typically, the temperature compensation circuit responds only to voltages between 0 and VS/2, or about 2.5 V when VS = 5 V. Figure 41 in the Power-Down Interface section shows a simplified schematic representation of the TADJ/PWDN interface. 2.5kΩ ACOM 08218-149 0.2 08218-044 2.75 Figure 42. VSET Interface Simplified Schematic OUTPUT INTERFACE The ADL5902 incorporates rail-to-rail output drivers with pullup and pull-down capabilities. The closed-loop, − 3dB bandwidth from the input of the output amplifier to the output with no load is approximately 58 MHz with a single-pole roll off of approximately −20 dB/decade. The output noise is approximately 25 nV/√Hz at 100 kHz. The VOUT pin can source and sink up to 10 mA. There is also an internal load from VOUT to COMM of 2500 Ω. VPOS POWER-DOWN INTERFACE When the voltage on this pin is greater than VS − 0.1 V, the device is fully powered down. Figure 32 shows this characteristic as a function of VPWDN. Note that, because of the design of this section of the ADL5902, as VPWDN passes through a narrow range at Rev. B | Page 18 of 28 ESD 2pF CLPF VOUT ESD 2kΩ ESD 500Ω COMM Figure 43. VOUT Interface Simplified Schematic 08218-045 The quiescent and disabled currents for the ADL5902 at 25°C are approximately 73 mA and 300 μA, respectively. The dual function TADJ/PWDN pin is connected to the temperature compensation circuit as well as the power-down circuit. Typically, the temperature compensation circuit responds only to voltages between 0 and VS/2, or about 2.5 V when VS = 5 V. Data Sheet ADL5902 VTGT INTERFACE The target voltage can be set with an external source or by connecting the VREF pin (nominally 2.3 V) to the VTGT pin through a resistive voltage divider. With 0.8 V on the VTGT pin, the rms voltage that must be provided by the VGA to balance the AGC feedback loop is 0.8 V × 0.05 = 40 mV rms. Most of the characterization information in this data sheet was collected at VTGT = 0.8 V. Voltages higher and lower than this can be used; however, doing so increases or decreases the gain at the internal squaring cell, which results in a corresponding increase or decrease in intercept. This, in turn, affects the sensitivity and the usable measurement range, in addition to the sensitivity to different carrier modulation schemes. As VTGT decreases, the squaring circuits produce more noise; this becomes noticeable in the output response at low input signal amplitudes. As VTGT increases, measurement error due to modulation increases and temperature drift tends to decrease. The chosen VTGT value of 0.8 V represents a compromise between these characteristics. VPOS An example of this type of plot is Figure 3. The slope and intercept that form the ideal line are those at 25°C with CW modulation. Figure 21 and Figure 24 show the error with various popular forms of modulation with respect to the ideal CW line. This method for calculating error is accurate, assuming that each device is calibrated at room temperature. In the second plot format, the VOUT voltage at a given input amplitude and temperature is subtracted from the corresponding VOUT at 25°C and then divided by the 25°C slope to obtain an error in decibels. This type of plot does not provide any information on the linear-in-dB performance of the device; it merely shows the decibel equivalent of the deviation of VOUT over temperature, given a calibration at 25°C. When calculating error from any one particular calibration point, this error format is accurate. It is accurate over the full range shown on the plot assuming that enough calibration points are used. Figure 6 shows this plot type. The error calculations for Figure 30 are similar to those for the VOUT plots. The slope and intercept of the VTEMP function vs. temperature are determined and applied as follows: ESD g × X2 VTGT 50kΩ Error (°C) = (VTEMP − Slope × (Temp − TZ))/Slope ITGT ESD 10kΩ COMM 08218-048 50kΩ ESD Figure 44. VTGT Interface where: TZ is the x-axis intercept expressed in degrees Celsius (the temperature that results in a VTEMP of 0 V if possible). Temp is the ambient temperature of the ADL5902 in degrees Celsius. Slope is, typically, 4.9 mV/°C. VTEMP is the voltage at the TEMP pin at that temperature. MEASUREMENT MODE BASIC CONNECTIONS BASIS FOR ERROR CALCULATIONS The slope and intercept used in the error plots are calculated using the coefficients of a linear regression performed on data collected in the central operating range. The error plots in the Typical Performance Characteristics section are shown in two formats: error from the ideal line and error with respect to the 25°C output voltage. The error from the ideal line is the decibel difference in VOUT from the ideal straight-line fit of VOUT calculated by the linear-regression fit over the linear range of the detector, typically at 25°C. The error in decibels is calculated by Error (dB) = (VOUT − Slope × (PIN − PZ))/Slope (16) (15) where PZ is the x-axis intercept expressed in decibels relative to 1 milliwatt (the input amplitude produces a 0 V output if such an output is possible). The error from the ideal line is not a measure of absolute accuracy because it is calculated using the slope and intercept of each device. However, it verifies the linearity and the effect of temperature and modulation on the response of the device. Figure 45 shows the basic connections for operating the ADL5902 as they are implemented on the device evaluation board. The ADL5902 requires a single supply of nominally 5 V. The supply is connected to the two VPOS supply pins. These pins must each be decoupled using the two capacitors with values equal or similar to those shown in Figure 45. These capacitors must be placed as close as possible to the VPOS pins. An external 60.4 Ω resistor (R3) combines with the relatively high RF input impedance of the ADL5902 to provide a broadband 50 Ω match. An ac coupling capacitor must be placed between this resistor and INHI. The INLO input must be ac-coupled to ground using the same value capacitor. Because the ADL5902 has a minimum input operating frequency of 50 MHz, 100 pF ac coupling capacitors can be used. The ADL5902 is placed in measurement mode by connecting VOUT to VSET. In measurement mode, the output voltage is proportional to the log of the rms input signal level. Rev. B | Page 19 of 28 ADL5902 Data Sheet VPOS +5V (RED) C3 0.1µF C7 0.1µF C4 100pF GND (BLACK) C5 100pF TEMP (BLACK) VPOS POS 10 TEMPERATURE SENSOR ADL5902 C10 100pF RFIN R3 60.4Ω 8 7 INHI INLO X2 15 LINEAR-IN-dB VGA (NEGATIVE SLOPE) R2 OPEN ITGT G=5 BIAS AND POWERDOWN CONTROL VSET R6 0Ω X2 NC 2 NC 16 6 VREF 2.3V 5 NC 13 11 1 TC2 PWDN (BLACK) R12 301Ω 12 VREF R9 1430Ω VTGT R10 3.74kΩ VREF (BLACK) 9 COMM R11 2kΩ R1 0Ω VOUT VOUT (BLACK) R15 OPEN CLPF 26pF TADJ/PWDN VSET (BLACK) IDET 14 C12 100pF TEMP C9 10µF 4 COMM VTGT (BLACK) 08218-145 3 Figure 45. Basic Connections for Operation in Measurement Mode SETTING VTADJ SETTING VTGT As discussed in the Theory of Operation section, the output temperature drift must be compensated by applying a voltage to the TADJ pin. The compensating voltage varies with frequency. The voltage for the TADJ pin can be easily derived from a resistor divider connected to the VREF pin. Table 5 shows the recommended VTADJ for operation from −40°C to +85°C, along with resistor divider values. Resistor values are chosen so that they neither pull too much current from VREF (VREF short-circuit current is 4 mA) nor are so large that the TADJ pin bias current of 3 μA affects the resulting voltage at the TADJ pin. As discussed in the Theory of Operation section, setting the voltage on VTGT to 0.8 V represents a compromise between achieving excellent rms compliance and maximizing dynamic range. The voltage on VTGT can be derived from the VREF pin using a resistor divider as shown Figure 45 (Resistor R10 and Resistor R11). Like the resistors chosen to set the VTADJ voltage, the resistors setting VTGT must have reasonable values that do not pull too much current from VREF or cause bias current errors. Also, attention must be paid to the combined current that VREF must deliver to generate the VTADJ and VTGT voltages. This current must be kept well below the VREF short-circuit current of 4 mA. Table 5. Recommended VTADJ for Selected Frequencies Frequency 100 MHz 700 MHz to 2.14 GHz 2.6 GHz 3.5 GHz 5.8 GHz VTADJ (V) 0.5 0.4 0.45 0.5 0.95 R9 (Ω) 1430 1430 1430 1430 1430 R12 (Ω) 402 301 348 402 1007 CHOOSING A VALUE FOR CLPF CLPF (C9 in Figure 45) provides the averaging function for the internal rms computation. Using the minimum value for CLPF allows the quickest response time to a pulsed waveform but leaves significant output noise on the output voltage signal. By the same token, a large filter cap reduces output noise but at the expense of response time. For non response-time critical applications, a relatively large capacitor can be placed on the CLPF pin. In Figure 45, a value of 0.1 μF is used. For most signal modulation schemes, this value ensures excellent rms measurement compliance and low residual output noise. There is no maximum capacitance limit for CLPF. Rev. B | Page 20 of 28 Data Sheet ADL5902 In applications where the response time is critical, a different approach to signal filtering can be taken. This is shown in Figure 47. The capacitor on the CLPF pin is set to the minimum value that ensures that a valid rms computation is performed. The job of noise removal is then handed off to an RC filter on the VOUT pin. This approach ensures that there is enough averaging to ensure good rms compliance and does not burden the rms computation loop with extra filtering that significantly slows down the response time. By finishing the filtering process using an RC filter after VOUT, faster fall times can be achieved with an equivalent amount of output noise. It must be noted that the RC filter can also be implemented in the digital domain after the analog-to-digital converter. Figure 46 shows how output noise varies with CLPF when the ADL5902 is driven by a single-carrier W-CDMA signal (Test Model TM1-64, peak envelope power = 10.56 dB, bandwidth = 3.84 MHz). With a 10 μF capacitor on CLPF, there is residual noise on VOUT of 4.4 mV p-p, which is less than 0.1 dB error (assuming a slope of approximately 53 mV/dB). 100k 200 10k 150 1k 100 100 50 10 0 1 10 1 1000 100 In Figure 47, CLPF is equal to 10 nF. This value was experimentally determined to be the minimum capacitance that ensures good rms compliance when the ADL5902 is driven by a 1 C W-CDMA signal (TM1-64). This test was carried out by starting out with a large capacitance value on the CLPF pin (for example, 10 μF). The value of VOUT was noted for a fixed input power level (for example, −10 dBm). The value of CLPF was then progressively reduced (this can be done with press-down capacitors) until the value of VOUT started to deviate from the original value (this indicates that the accuracy of the rms computation is degrading and that CLPF is getting too small). CLPF (nF) Figure 46. Output Noise, Rise and Fall Times vs. CLPF Capacitance, SingleCarrier W-CDMA (TM1-64) at 2.14 GHz with PIN = 0 dBm Figure 46 also shows how CLPF affects the response time of VOUT. To measure this, a RF burst at 2.14 GHz at −10 dBm was applied to the ADL5902. The 10% to 90% rise time and 90% to 10% fall time is then measured. It is notable that the fall time is much longer than the rise time. This can also be seen in the response time plots, Figure 22, Figure 23, Figure 25, and Figure 26. VPOS POS 3 10 ADL5902 TEMPERATURE SENSOR 8 7 INHI 14 X2 INLO 15 LINEAR-IN-dB VGA (NEGATIVE SLOPE) NC X2 ITGT RFILTER 2kΩ G=5 BIAS AND POWERDOWN CONTROL VSET IDET 2 NC 16 TEMP 6 VREF 2.3V 5 NC 13 26pF 1 11 12 TADJ/PWDN VREF VTGT 9 4 COMM VOUT CLPF C9 10nF (SEE TABLE 6 AND FIGURE 46.) COMM Figure 47. Optimizing Setting Time and Residual Ripple Rev. B | Page 21 of 28 VOUT CFILTER (SEE FIGURE 48.) 08218-147 OUTPUT NOISE (mV p-p) 250 1M RISE/FALL TIME (µs) OUTPUT NOISE (mV p-p) 10% TO 90% RISE TIME (µs) 90% TO 10% FALL TIME (µs) 08218-146 300 ADL5902 Data Sheet Figure 48 shows the resulting rise and fall times (signal is pulsed between off and −10 dBm) with CLPF equal to 10 nF. A 2 kΩ resistor is placed in series with the VOUT pin, and the capacitance from this resistor to ground (CFILTER in Figure 47) is varied up to 1 μF. RESIDUAL RIPPLE (mV p-p) 250 1M 200 10k 150 1k 100 100 50 10 0 1 10 1 1k 100 Table 6 shows recommended minimum values of CLPF for popular modulation schemes, using just a single filter capacitor at the CLPF pin. Using lower capacitor values results in rms measurement errors. Output response time (10% to 90%) is also shown. If the output noise shown in Table 6 is unacceptably high, it can be reduced by 100k CFILTER (nF) RISE/FALL TIME (µs) RESIDUAL RIPPLE (V p-p) 10% TO 90% RISE TIME (µs) 90% TO 10% FALL TIME (µs) As CFILTER is reduced, the fall time flattens out. This is because the fall time is now dominated by the 10 nF CLPF which is present throughout the measurement. Increasing CLPF Adding an RC filter at VOUT, as shown in Figure 47 Implementing an averaging algorithm after the ADL5902 output voltage is digitized by an ADC 08218-148 300 For large values of CFILTER, the fall time is dramatically reduced compared to Figure 46. This comes at the expense of a moderate increase in rise time. Figure 48. Residual Ripple, Rise and Fall Times Using an RC Low-Pass Filter at VOUT, PIN = 0 dBm at 2.14 GHz Table 6. Recommended Minimum CLPF Values for Various Modulation Schemes Modulation/Standard W-CDMA, One-Carrier, TM1-64 W-CDMA Four-Carrier, TM1-64, TM1-32, TM1-16, TM1-8 LTE, TM1 1CR 20 MHz (2048 Subcarriers, QPSK Subcarrier Modulation) Peak-Envelope Power 10.56 dB 12.08 dB Signal Bandwidth 3.84 MHz 18.84 MHz CLPF (min) 10 nF 5.6 nF Output Noise 95 mV p-p 164 mV p-p Rise/Fall Time (10% to 90%) 11.58 dB 20 MHz 1000 pF 452 mV p-p 1.3/38 s Rev. B | Page 22 of 28 12/330 s 7/200 s Data Sheet ADL5902 Table 7. Output Voltage Range Scaling OUTPUT VOLTAGE SCALING The output voltage range of the ADL5902 (nominally 0.3 V to 3.5 V) can be easily increased or decreased. There are a number of situations where adjustment of the output scaling makes sense. For example, if the ADL5902 is driving an analog-to-digital converter (ADC) with a 0 V to 5 V input range, it makes sense to increase the detector nominal maximum output voltage of 3.5 V so that it is closer to 5 V. This makes better use of the input range of the ADC and maximizes the resolution of the system in terms of bits/dB. For more information on interfacing the ADL5902 to an ADC, please refer to Circuit Note CN0178. If only a part of the ADL5902 RF input power range is being used (for example, −10 dBm to −60 dBm), it can make sense to increase the scaling so that this reduced input range fits into the ADL5902 available output swing of 0 V to 4.8 V. The output swing can also be reduced by simply adding a voltage divider on the output pin, as shown in the circuit on the left-hand side of Figure 49. Reducing the output scaling can, for example, be used when interfacing the ADL5902 to an ADC with a 0 V to 2.5 V input range. Recommended scaling resistors for a slope decrease are provided in Table 7. The output voltage swing can be increased using a technique that is analogous to setting the gain of an op amp in noninverting mode with the VSET pin being the equivalent of the inverting input of the op amp. This is shown in the circuit on the left-hand side of Figure 49. Connecting VOUT to VSET results in the nominal 0 V to 3.5 V swing and a slope of approximately 53 mV/dB (this varies slightly with frequency). Figure 49 and Table 7 show the configurations for increasing the slope, along with recommended standard resistor values for particular input ranges and output swings. 7 VSET 7 VSET R2 R6 6 VOUT R1 6 VOUT 08218-049 R15 Desired Input Range (dBm) 0 to −60 −10 to −50 0 to −60 −10 to −50 R6 (Ω) 665 1180 R2 (Ω) 2000 2000 R1 (Ω) R15 (Ω) 806 324 2000 2000 New Slope (mV/dB) 72.1 86.3 38.3 46.2 Nominal Output Voltage Range (V) 0.195 to 4.52 1.096 to 4.55 0.103 to 2.49 0.587 to 2.43 Equation 17 is the general function that governs this. V ' R 6 ( R2 || RIN ) O 1 VO (17) where: VO is the nominal maximum output voltage (see Figure 6 through Figure 18). V'O is the new maximum output voltage (for example, up to 4.8 V). RIN is the VSET input resistance (72 kΩ). When choosing R6 and R2, attention must be paid to the current drive capability of the VOUT pin and the input resistance of the VSET pin. The choice of resistors must not result in excessive current draw out of VOUT. However, making R6 and R2 too large is also problematic. If the value of R2 is compatible with the input resistance of the VSET input (72 kΩ), this input resistance, which varies slightly from device to device, contributes to the resulting slope and output voltage. In general, the value of R2 must be at least ten times smaller than the input resistance of VSET. Values for R6 and R2 must, therefore, be in the 1 kΩ to 5 kΩ range. It is also important to take into account device to device and frequency variation in output swing along with the ADL5902 output stage maximum output voltage of 4.8 V. The VOUT distribution is well characterized at major frequencies’ bands in the Typical Performance Characteristics section (see Figure 6 through Figure 8, Figure 12 through Figure 14, Figure 18, and Figure 19). The resistor values in Table 7, which are calculated based on 900 MHz performance, are conservatively chosen so that there is no chance that the output voltages exceed the ADL5902 output swing or the input range of a 0 V to 2.5 V and 0 V to 5 V ADC. Because the output swing does not vary much with frequency (it does start to drop off above 3 GHz), these values work for multiple frequencies. Figure 49. Decreasing and Increasing Slope Rev. B | Page 23 of 28 ADL5902 Data Sheet 6 VOUT ERROR 2-POINT CAL AT 0dBm, AND 40dBm ERROR 3-POINT CAL AT 0 dBm, –45dBm, AND 60dBm ERROR 4-POINT CAL AT 0dBm, –20dBm, –45dBm, AND –60dBm 5 5 4 3 2 1 0 3 –1 ERROR (dB) VOUT (V) 4 –2 2 –3 –4 1 0 –70 –60 –50 –40 –30 –20 –10 0 10 –6 PIN (dBm) 08218-050 –5 Figure 50. 2.14 GHz Transfer Function, Using Various Calibration Techniques Because slope and intercept vary from device to device, boardlevel calibration must be performed to achieve high accuracy. The equation for the idealized output voltage can be written as VOUT(IDEAL) = Slope × (PIN − Intercept) Figure 51 shows the output voltage and error at 25°C and over temperature when a four-point calibration is used (calibration points are 0 dBm, −20 dBm, −45 dBm, and −60 dBm). When choosing calibration points, there is no requirement for, or value, in equal spacing between the points. There is also no limit to the number of calibration points used. However, using more calibration points increases calibration time. 6 (18) where: Slope is the change in output voltage divided by the change in input power (dB). Intercept is the calculated input power level at which the output voltage is 0 V (note that Intercept is an extrapolated theoretical value not a measured value). 5 4 VOUT (V) 6 The residual nonlinearity of the transfer function that is apparent in the two-point calibration error plot can be reduced by increasing the number of calibration points. Figure 50 shows the postcalibration error plots for three-point and four-point calibrations. With a multipoint calibration, the transfer function is segmented, with each segment having a slope and intercept. Multiple known power levels are applied, and multiple voltages are measured. When the equipment is in operation, the measured voltage from the detector first determines which of the stored slope and intercept calibration coefficients are to be used. Then the unknown power level is calculated by inserting the appropriate slope and intercept into Equation 21. 4 3 2 1 3 0 –1 –2 –3 –4 1 –5 0 –70 –60 –50 –40 –30 PIN (dBm) –20 –10 0 –6 10 Figure 51. 2.14 GHz Transfer Function and Error at +25°C, −40°C, and +85°C Using a Four-Point Calibration (0 dBm, −20 dBm, −45 dBm, −60 dBm) With a two-point calibration, the slope and intercept are calculated as follows: Slope = (VOUT1 − VOUT2)/(PIN1 − PIN2) (19) Intercept = PIN1 − (VOUT1/Slope) (20) After the slope and intercept are calculated and stored in nonvolatile memory during equipment calibration, an equation can calculate an unknown input power based on the output voltage of the detector. The −40°C and +85°C error plots in Figure 51 are generated using the 25°C calibration coefficients. This is consistent with equipment calibration in a mass production environment where calibration at just a single temperature is practical. (21) The log conformance error is the difference between this straight line and the actual performance of the detector. Error (dB) = (VOUT(MEASURED) − VOUT(IDEAL))/Slope 5 2 In general, calibration is performed during equipment manufacture by applying two or more known signal levels to the input of the ADL5902 and measuring the corresponding output voltages. The calibration points are generally within the linearin-dB operating range of the device. PIN (Unknown) = (VOUT1(MEASURED)/Slope) + Intercept 6 +85°C VOUT +25°C VOUT –40°C VOUT +85°C ERROR 4-POINT CAL +25°C ERROR 4-POINT CAL AT 0dBm, –20dBm, –45dBm, AND –60dBm –40°C ERROR 4-POINT CAL ERROR (dB) The measured transfer function of the ADL5902 at 2.14 GHz is shown in Figure 50, which contains plots of both output voltage vs. input amplitude (power) and calculated error vs. input level. As the input level varies from −62 dBm to +3 dBm, the output voltage varies from ~0.25 V to ~3.5 V. Figure 50 includes a plot of this error when using a two-point calibration (calibration points are 0 dBm and −40 dBm). The error at the calibration points (in this case, −40 dBm and 0 dBm) is equal to 0 by definition. 08218-051 SYSTEM CALIBRATION AND ERROR CALCULATION (22) Rev. B | Page 24 of 28 Data Sheet ADL5902 HIGH FREQUENCY PERFORMANCE DESCRIPTION OF CHARACTERIZATION The ADL5902 is specified to 6 GHz; however, operation is possible to as high as 9 GHz with sufficient dynamic range for many purposes. Figure 52 shows the typical VOUT response and conformance error at 7 GHz, 8 GHz, and 9 GHz. The general hardware configuration used for most of the ADL5902 characterization is shown in Figure 53. The ADL5902 was driven in a single-ended configuration for most characterization, except where noted. 4 2.25 3 2.00 2 1.75 1 1.50 0 1.25 –1 1.00 –2 0.75 –3 0.50 –4 0.25 –5 0 –50 –40 –30 –20 –10 0 10 Much of the data was taken using an Agilent E4438C signal source as a RF input stimulus. Several ADL5902 devices mounted on circuit boards constructed of Rodgers 3006 material are put into a test chamber simultaneously, and a Keithley S46 RF switching network connected the signal source to the appropriate device under test. The test chamber temperature was set to cycle over the appropriate temperature range. The signal source, switching, and chamber temperature are all controlled by a PC running Agilent VEE Pro. 5 The subsequent response to stimulus was measured with a voltmeter and the results stored in a database for analysis later. In this way, multiple ADL5902 devices are characterized over amplitude, frequency, and temperature in a minimum amount of time. The RF stimulus amplitude was calibrated up to the circuit board that carries the ADL5902, and, thus, it does not account for the slight losses due to the connector on the circuit board that carries the ADL5902 nor for the loss of traces on the circuit board. For this reason, there is a small absolute amplitude error (generally <0.5 dB) not accounted for in the characterization data, but this is generally not important because the ADL5902 relative accuracy is unaffected. –6 PIN (dBm) Figure 52. Typical VOUT and Log Conformance Error at 7 GHz, 8 GHz, and 9 GHz, 25°C Only LOW FREQUENCY PERFORMANCE The lowest frequency of operation of the ADL5902 is approximately 50 MHz. This is the result of the circuit design and architecture of the ADL5902. AGILENT E3631A DC POWER SUPPLIES AGILENT 34980A SWITCH MATRIX/ DC METER AGILENT E8251A MICROWAVE SIGNAL GENERATOR KEITHLEY S46 MICROWAVE SWITCH ADL5902 CHARACTERIZ ATION BOARD – TEST SITE 2 ADL5902 CHARACTERIZ ATION BOARD – TEST SITE 3 PERSONAL COMPUTER RF ADL5902 CHARACTERIZ ATION BOARD – TEST SITE 1 DC DATA AND CONTROL Figure 53. General Characterization Configuration Rev. B | Page 25 of 28 08218-075 OUTPUT VOLTAGE (V) 2.50 6 ERROR (dB) 7GHz 8GHz 9GHz 2.75 08218-057 3.00 ADL5902 Data Sheet EVALUATION BOARD SCHEMATICS AND ARTWORK C3 0.1µF VPOS +5V (RED) C7 0.1µF C4 100pF GND (BLACK) C5 100pF TEMP (BLACK) VPOS POS 10 TEMPERATURE SENSOR ADL5902 C10 100pF RFIN R3 60.4Ω 8 7 INHI INLO X2 15 LINEAR-IN-dB VGA (NEGATIVE SLOPE) R2 OPEN ITGT G=5 BIAS AND POWERDOWN CONTROL VSET R6 0Ω X2 NC 2 NC 16 6 VREF 2.3V 5 NC 13 1 TADJ/PWDN TC2 PWDN (BLACK) R12 301Ω 12 VREF R9 1430Ω VTGT R10 3.74kΩ VREF (BLACK) 9 VOUT (BLACK) R15 OPEN CLPF C9 10µF 4 COMM R11 2kΩ R1 0Ω VOUT 26pF 11 VSET (BLACK) IDET 14 C12 100pF TEMP COMM VTGT (BLACK) 08218-150 3 Figure 54. Evaluation Board Schematic Table 8. Evaluation Board Configuration Options Component C10, C12, R3 R10, R11 C4, C5, C7, C3 R1, R15, R2, R6 C9 R9, R12 Function/Notes RF input. The ADL5902 is generally driven single-ended. R3 is the input termination resistor and is chosen to give a 50 Ω input impedance over a broad frequency range. VTGT interface. R10 and R11 are set up to provide 0.8 V to VTGT derived from VREF. Power supply decoupling. The nominal supply decoupling consists of two pairs of 100 pF and 0.1 μF capacitors placed close to the two power supply pins of the ADL5902. Output interface. In measurement mode, a portion of the voltage at the VOUT pin is fed back to the VSET pin via R6. Using the voltage divider created by R2 and R6, the magnitude of the slope of VOUT is increased by reducing the portion of VOUT that is fed back to VSET. In controller mode, R6 must be open. In this mode, the ADL5902 can control the gain of an external component. A setpoint voltage is applied to the VSET pin, the value of which corresponds to the desired RF input signal level applied to the ADL5902. Low-pass filter capacitors, CLPF. The low-pass filter capacitor provides the averaging for the ADL5902 rms computation. TADJ/PWDN. The TADJ/PWDN pin controls the amount of nonlinear intercept temperature compensation and/or shuts down the device. The evaluation board is configured with TADJ connected to VREF through a resistor divider (R9, R12). Rev. B | Page 26 of 28 Default Value C10 = C12 = 100 pF R3 = 60.4 Ω R10 = 3.74 kΩ, R11 = 2 kΩ C4 = C5 = 100 pF, C7 = C3 = 0.1 μF R1 = R6= 0 Ω, R2 = R15 = open C9 = 0.1 μF R9 = 1430 Ω R12 = 301 Ω Data Sheet ADL5902 08218-060 08218-061 ASSEMBLY DRAWINGS Figure 56. Evaluation Board Layout, Bottom Side Figure 55. Evaluation Board Layout, Top Side Rev. B | Page 27 of 28 ADL5902 Data Sheet OUTLINE DIMENSIONS 0.35 0.30 0.25 0.65 BSC PIN 1 INDICATOR 16 13 1 12 *2.40 EXPOSED PAD 2.35 SQ 2.30 9 TOP VIEW 0.80 0.75 0.70 4 5 8 BOTTOM VIEW 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF SEATING PLANE PKG-000000 0.50 0.40 0.30 0.25 MIN FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. *COMPLIANT TO JEDEC STANDARDS MO-220-WGGC-3 WITH EXCEPTION TO THE EXPOSED PAD. 07-21-2015-B PIN 1 INDICATOR 4.10 4.00 SQ 3.90 Figure 57. 16-Lead Lead Frame Chip Scale Package [LFCSP] 4 mm × 4 mm Body and 0.75 mm Package Height (CP-16-20) Dimensions shown in millimeters ORDERING GUIDE Model1 ADL5902ACPZ-R7 ADL5902ACPZ-R2 ADL5902ACPZ-WP ADL5902-EVALZ 1 Temperature Range −40°C to +125°C −40°C to +125°C −40°C to +125°C Package Description 16-Lead Lead Frame Chip Scale Package [LFCSP] 16-Lead Lead Frame Chip Scale Package [LFCSP] 16-Lead Lead Frame Chip Scale Package [LFCSP] Evaluation Board Z = RoHS Compliant Part. ©2010–2016 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D08218-0-8/16(B) Rev. B | Page 28 of 28 Package Option CP-16-20 CP-16-20 CP-16-20 Ordering Quantity 1,500 250 64