TOCOS GF281G20SB101K 28mm diameter, single-turn, cermet industrial panel control Datasheet

TOCOS
®
GF281 Series
PA N E L C O N T R O L S
28mm Diameter, Single-Turn, Cermet Industrial Panel Controls
GF281G
GF281
Features
28mm diameter, single-turn industrial panel controls Cermet film element Single and tandem units, single shaft
Excellent environmental characteristics Linear taper Shaft lock available Metal shaft and bushing
6mm diameter shafts in slot, flat or round end styles Standard 15mm or 20mm shaft length Panel mount only
Right angle ear-lug terminals Optional 6-turn GFV281 model available as special order
Specifications
Electrical
Environmental
Standard Resistance Range . . . . . . . . . . . . . 100Ω to 1MΩ
Temperature Range . . . . . . . . . . . . . . . . . 10C to 120C
Resistance Tolerance . . . . . . . . . . . . . . . . . 10% standard
Low Temperature Operation . . . . . . . . .10C, 45 minutes
with rated load
∆T/R )3%
End Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Ω max.
Resistance Taper . . . . . . . . . . . . . . . . . . . . . . . . . . B = linear
Peak Noise (C.R.V.) . . . . . . . 3% or 5Ω, whichever is greater
Power Rating . . . . . . . . 2 watts at 70C, 0 watt at 120C
Load Life . . . . . . . . . . . . 70C, 1,000 hours with rated load
∆T/R )5%
Maximum Input Voltage . . . . . . . . 400VDC or power rating,
whichever is smaller
Vibration . . . . . . . . . . . . . . . . . . .10-55Hz, 1.5mm amplitude,
3 directions, 2 hours each
∆T/R )1%
Temperature Coefficient . . . 100 ppm /C, 200Ω to 500kΩ
250 ppm /C, other values
Soldering Heat Resistance . . . . . . . . . . . 350C, 3 seconds
∆T/R )2%
Dielectric Strength . . . . . . . . . . . . . . . . 1,000VAC, 1 minute
Rotational Life . . . . 15,000 cycles (500 cycles for shaft lock
models only) without load
∆T/R )10%
Mechanical
Mechanical Travel . . . . . . . . . . . . . . . . . . . . . . . . . 29510
∆T/R = Total Resistance Change
Shaft Torque
Single Unit . . . . . . 50 to 300 gf • cm (0.693 to 4.159 oz • in)
Tandem Unit . . . . . 50 to 450 gf • cm (0.693 to 6.238 oz • in)
Stop Strength . . . . . . . . . . . 9.2 kgf • cm (127.54 oz • in) max.
Mounting Nut Torque . . . . . . 15 kgf • cm (207.94 oz • in) max.
Solderability . . . . . . . . . . . . . . . . . . . . . . . 235C, 5 seconds
Marking . . . . . . . . . . . . . . . . . . Model type, taper, resistance,
shaft type, terminal identification, date code
TOCOS AMERICA, INC.
1177 East Tower Road, Schaumburg, IL 60173
Tel: 847-884-6664
Fax: 847-884-6665
81
E-mail: [email protected]
www.tocos.com
GF281 Series
Dimensions
GF281 Single-Turn & GFV281 6-Turn (special order)
Unit: mm
Panel Mount, Single Unit, Single Shaft
Right Angle Ear-Lug Terminals
Recommended
Panel Mounting Holes
GF281L
Panel Mount, Single Unit, Single Shaft with Shaft Lock
Right Angle Ear-Lug Terminals
Recommended
Panel Mounting Holes
GF281G
Panel Mount, Ganged Tandem Unit, Single Shaft
Right Angle Ear-Lug Terminals on Each Unit
Recommended
Panel Mounting Holes
TOCOS AMERICA, INC.
82
1177 East Tower Road, Schaumburg, IL 60173
Tel: 847-884-6664
Fax: 847-884-6665
E-mail: [email protected]
www.tocos.com
GF281 Series
Part Numbering System
GF 281 G L 15 S B 103 K
NOTE: FMS = From Mounting Surface
Resistance Tolerance: K = 10% (standard).
Resistance Code: Expressed in ohms. A three digit code where the first
two digits are significant figures, and the third digit indicates the number
of zeros that follow these figures (i.e., 100 = 10Ω; 101 = 100Ω; 102 = 1,000Ω;
103 = 10,000Ω; 105 = 1,000,000Ω ). See table for standard resistance values.
For Single Unit:
Specify taper and resistance code as shown.
For Ganged Tandem Unit:
Specify a taper code and resistance code for each unit starting with
the front unit followed by the rear unit. If both units have the same taper
and resistance codes, add “X2” suffix per example below.
Examples: B103A503 or if both units are the same: B103X2
Resistance Taper: B = Linear.
Shaft End Style: S = Slotted.
F = Flatted.
R = Round.
Standard Shaft Length: 15 = 15 mm FMS.
20 = 20mm FMS.
Up to 50mm shaft length available (special order ).
Shaft Lock: L = With Shaft Lock.
Blank = Without Shaft Lock.
Style: Blank = Panel Mount, Single Unit, Single Shaft, Right Angle
Ear-Lug Terminals.
G = Panel Mount, Ganged Tandem Unit, Single Shaft,
Right Angle Ear-Lug Terminals on Each Unit.
Size: 281 = 28mm Diameter.
TOCOS Series Name: GF = Cermet Film Element.
Standard Resistance Values and Part Numbering Codes
Standard Nominal Total Resistance Values and Part Numbering Codes
Resistance ( Ω )
Code
Resistance ( Ω )
Code
Resistance ( Ω )
Code
Resistance ( Ω )
Code
Resistance ( Ω )
Code
100
200
500
101
201
501
1,000
2,000
5,000
102
202
502
10,000
20,000
50,000
103
203
503
100,000
200,000
500,000
104
204
504
1,000,000
105
Refer to Shaft End Styles Specifications and Hardware Specifications for details and availability.
For additional information, refer to Guidelines and Precautions for Using Panel Controls.
TOCOS AMERICA, INC.
1177 East Tower Road, Schaumburg, IL 60173
Tel: 847-884-6664
Fax: 847-884-6665
83
E-mail: [email protected]
www.tocos.com
Similar pages