TI1 LM1084IT-5.0/NOPB Lm1084 5a low dropout positive regulator Datasheet

LM1084
www.ti.com
SNVS037F – SEPTEMBER 1999 – REVISED MARCH 2013
LM1084 5A Low Dropout Positive Regulators
Check for Samples: LM1084
FEATURES
DESCRIPTION
•
The LM1084 is a series of low dropout voltage
positive regulators with a maximum dropout of 1.5V
at 5A of load current. It has the same pin-out as TI's
industry standard LM317.
1
2
•
•
•
•
•
Available in 3.3V, 5.0V, 12V and Adjustable
Versions
Current Limiting and Thermal Protection
Output Current 5A
Industrial Temperature Range −40°C to 125°C
Line Regulation 0.015% (typical)
Load Regulation 0.1% (typical)
APPLICATIONS
•
•
•
Post Regulator for Switching DC/DC Conveter
High Efficiency Linear Regulators
Battery Charger
The LM1084 is available in an adjustable version,
which can set the output voltage with only two
external resistors. It is also available in three fixed
voltages: 3.3V, 5.0V and 12.0V. The fixed versions
intergrate the adjust resistors.
The LM1084 circuit includes a zener trimmed
bandgap reference, current limiting and thermal
shutdown.
Connection Diagram
Figure 1. TO-220 Top View
Figure 2. DDPAK/TO-263 Top View
Figure 3. Basic Functional Diagram, Adjustable
Version
Figure 4. Application Circuit
1.2V to 15V Adjustable Regulator
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1999–2013, Texas Instruments Incorporated
LM1084
SNVS037F – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
Simplified Schematic
Figure 5.
2
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM1084
LM1084
www.ti.com
SNVS037F – SEPTEMBER 1999 – REVISED MARCH 2013
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1) (2)
Maximum Input to Output Voltage Differential
LM1084-ADJ
29V
LM1084-12
18V
LM1084-3.3
27V
LM1084-5.0
25V
Power Dissipation
(3)
Internally Limited
Junction Temperature (TJ) (4)
150°C
Storage Temperature Range
-65°C to 150°C
Lead Temperature
260°C, to 10 sec
(5)
2000V
ESD Tolerance
(1)
(2)
(3)
(4)
(5)
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the Electrical Characteristics.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
Power dissipation is kept in a safe range by current limiting circuitry. Refer to Overload Recovery in Application Notes.
The maximum power dissipation is a function of TJ(max) , θJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(max)–T A)/θJA. All numbers apply for packages soldered directly into a PC board. Refer to THERMAL
CONSIDERATIONS in the Application Note.
For testing purposes, ESD was applied using human body model, 1.5kΩ in series with 100pF.
Operating Ratings (1)
Junction Temperature Range (TJ)
(1)
(2)
(2)
Control Section
−40°C to 125°C
Output Section
−40°C to 150°C
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the Electrical Characteristics.
The maximum power dissipation is a function of TJ(max) , θJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(max)–T A)/θJA. All numbers apply for packages soldered directly into a PC board. Refer to THERMAL
CONSIDERATIONS in the Application Note.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM1084
3
LM1084
SNVS037F – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
Electrical Characteristics
Typicals and limits appearing in normal type apply for TJ = 25°C. Limits appearing in Boldface type apply over the entire
junction temperature range for operation.
Symbol
VREF
VOUT
Output Voltage
(3)
Line Regulation
(4)
Load Regulation
(4)
Dropout Voltage
ILIMIT
(1)
(2)
(3)
(4)
(5)
(6)
4
Typ
Max
(1)
Units
1.238
1.225
1.250
1.250
1.262
1.270
V
V
LM1084-3.3
IOUT = 0mA, VIN = 8V
0 ≤ IOUT ≤IFULL LOAD, 4.8V≤ VIN ≤15V
3.270
3.235
3.300
3.300
3.330
3.365
V
V
LM1084-5.0
IOUT = 0mA, VIN = 8V
0 ≤ IOUT ≤ IFULL LOAD, 6.5V ≤ VIN ≤ 20V
4.950
4.900
5.000
5.000
5.050
5.100
V
V
LM1084-12
IOUT = 0mA, VIN = 15V
0 ≤ IOUT ≤ IFULL LOAD, 13.5V ≤ VIN ≤ 25V
11.880
11.760
12.000
12.000
12.120
12.240
V
V
0.015
0.035
0.2
0.2
%
%
LM1084-3.3
IOUT = 0mA, 4.8V ≤ VIN ≤ 15V
0.5
1.0
6
6
mV
mV
LM1084-5.0
IOUT = 0mA, 6.5V ≤ VIN ≤ 20V
0.5
1.0
10
10
mV
mV
LM1084-12
I OUT =0mA, 13.5V ≤ VIN ≤ 25V
1.0
2.0
25
25
mV
mV
LM1084-ADJ
(VIN-V OUT) = 3V, 10mA ≤ IOUT ≤ IFULL LOAD
0.1
0.2
0.3
0.4
%
%
LM1084-3.3
VIN = 5V, 0 ≤ IOUT ≤ IFULL LOAD
3
7
15
20
mV
mV
LM1084-5.0
VIN = 8V, 0 ≤ IOUT ≤ IFULL LOAD
5
10
20
35
mV
mV
LM1084-12
VIN = 15V, 0 ≤ IOUT ≤ IFULL LOAD
12
24
36
72
mV
mV
LM1084-ADJ, 3.3, 5, 12
ΔVREF, ΔVOUT = 1%, IOUT = 5A
1.3
1.5
V
Conditions
Reference Voltage
ΔVOUT
ΔVOUT
Min
Parameter
(5)
Current Limit
LM1084-ADJ
IOUT = 10mA, VIN−VOUT = 3V
10mA ≤IOUT ≤ IFULL LOAD,1.5V ≤ (VIN−VOUT) ≤ 25V
(1)
(3)
LM1084-ADJ
IOUT =10mA, 1.5V≤ (VIN-VOUT) ≤ 15V
(2)
LM1084-ADJ
VIN−VOUT = 5V
VIN−VOUT = 25V
5.5
0.3
8.0
0.6
A
A
LM1084-3.3
VIN = 8V
5.5
8.0
A
LM1084-5.0
VIN = 10V
5.5
8.0
A
LM1084-12
VIN = 17V
5.5
8.0
A
Minimum Load
Current (6)
LM1084-ADJ
VIN −VOUT = 25V
Quiescent Current
5
10.0
mA
LM1084-3.3
VIN = 18V
5.0
10.0
mA
LM1084-5.0
VIN ≤ 20V
5.0
10.0
mA
LM1084-12
VIN ≤ 25V
5.0
10.0
mA
All limits are specified by testing or statistical analysis.
Typical Values represent the most likely parametric norm.
IFULLLOAD is defined in the current limit curves. The IFULLLOAD Curve defines the current limit as a function of input-to-output voltage.
Note that 30W power dissipation for the LM1084 is only achievable over a limited range of input-to-output voltage.
Load and line regulation are measured at constant junction temperature, and are ensured up to the maximum power dissipation of 30W.
Power dissipation is determined by the input/output differential and the output current. ensured maximum power dissipation will not be
available over the full input/output range.
Dropout voltage is specified over the full output current range of the device.
The minimum output current required to maintain regulation.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM1084
LM1084
www.ti.com
SNVS037F – SEPTEMBER 1999 – REVISED MARCH 2013
Electrical Characteristics (continued)
Typicals and limits appearing in normal type apply for TJ = 25°C. Limits appearing in Boldface type apply over the entire
junction temperature range for operation.
Symbol
Parameter
Conditions
Thermal Regulation
TA = 25°C, 30ms Pulse
Ripple Rejection
fRIPPLE = 120Hz, = COUT = 25µF Tantalum,
IOUT = 5A
Min
(1)
Typ
Max
(1)
Units
0.003
0.015
%/W
(2)
LM1084-ADJ, CADJ, = 25µF, (VIN−VO) = 3V
60
75
dB
LM1084-3.3, VIN = 6.3V
60
72
dB
LM1084-5.0, VIN = 8V
60
68
dB
LM1084-12 VIN = 15V
54
60
dB
Adjust Pin Current
LM1084
55
120
µA
Adjust Pin Current
Change
10mA ≤ IOUT ≤ IFULL LOAD,
1.5V ≤ VIN−VOUT ≤ 25V
0.2
5
µA
Temperature Stability
0.5
Long Term Stability
TA =125°C, 1000Hrs
RMS Output Noise
(% of VOUT)
10Hz ≤ f≤ 10kHz
Thermal Resistance
Junction-to-Case
3-Lead DDPAK/TO-263: Control Section/Output Section
3-Lead TO-220: Control Section/Output Section
0.3
%
1.0
0.003
%
0.65/2.7
0.65/2.7
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM1084
%
°C/W
°C/W
5
LM1084
SNVS037F – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
6
Dropout Voltage (VIN−VOUT)
Short-Circuit Current
Figure 6.
Figure 7.
Load Regulation
LM1084-ADJ Ripple Rejection
Figure 8.
Figure 9.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM1084
LM1084
www.ti.com
SNVS037F – SEPTEMBER 1999 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
LM1084-ADJ Ripple Rejection vs Current
Temperature Stability
Figure 10.
Figure 11.
Adjust Pin Current
LM1084-ADJ Load Transient Response
Figure 12.
Figure 13.
LM1084-ADJ LineTransient Response
Maximum Power Dissipation
Figure 14.
Figure 15.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM1084
7
LM1084
SNVS037F – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
APPLICATION NOTE
GENERAL
Figure 16 shows a basic functional diagram for the LM1084-Adj (excluding protection circuitry) . The topology is
basically that of the LM317 except for the pass transistor. Instead of a Darlingtion NPN with its two diode voltage
drop, the LM1084 uses a single NPN. This results in a lower dropout voltage. The structure of the pass transistor
is also known as a quasi LDO. The advantage a quasi LDO over a PNP LDO is its inherently lower quiescent
current. The LM1084 is ensured to provide a minimum dropout voltage 1.5V over temperature, at full load.
Figure 16. Basic Functional Diagram for the LM1084, excluding Protection circuitry
OUTPUT VOLTAGE
The LM1084 adjustable version develops at 1.25V reference voltage, (VREF), between the output and the adjust
terminal. As shown in figure 2, this voltage is applied across resistor R1 to generate a constant current I1. This
constant current then flows through R2. The resulting voltage drop across R2 adds to the reference voltage to
sets the desired output voltage.
The current IADJ from the adjustment terminal introduces an output error . But since it is small (120uA max), it
becomes negligible when R1 is in the 100Ω range.
For fixed voltage devices, R1 and R2 are integrated inside the devices.
Figure 17. Basic Adjustable Regulator
STABILITY CONSIDERATION
Stability consideration primarily concern the phase response of the feedback loop. In order for stable operation,
the loop must maintain negative feedback. The LM1084 requires a certain amount series resistance with
capacitive loads. This series resistance introduces a zero within the loop to increase phase margin and thus
increase stability. The equivalent series resistance (ESR) of solid tantalum or aluminum electrolytic capacitors is
used to provide the appropriate zero (approximately 500 kHz).
The Aluminum electrolytic are less expensive than tantalums, but their ESR varies exponentially at cold
temperatures; therefore requiring close examination when choosing the desired transient response over
temperature. Tantalums are a convenient choice because their ESR varies less than 2:1 over temperature.
The recommended load/decoupling capacitance is a 10uF tantalum or a 50uF aluminum. These values will
assure stability for the majority of applications.
8
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM1084
LM1084
www.ti.com
SNVS037F – SEPTEMBER 1999 – REVISED MARCH 2013
The adjustable versions allows an additional capacitor to be used at the ADJ pin to increase ripple rejection. If
this is done the output capacitor should be increased to 22uF for tantalums or to 150uF for aluminum.
Capacitors other than tantalum or aluminum can be used at the adjust pin and the input pin. A 10uF capacitor is
a reasonable value at the input. See RIPPLE REJECTION section regarding the value for the adjust pin
capacitor.
It is desirable to have large output capacitance for applications that entail large changes in load current
(microprocessors for example). The higher the capacitance, the larger the available charge per demand. It is also
desirable to provide low ESR to reduce the change in output voltage:
ΔV = ΔI x ESR
It is common practice to use several tantalum and ceramic capacitors in parallel to reduce this change in the
output voltage by reducing the overall ESR.
Output capacitance can be increased indefinitely to improve transient response and stability.
RIPPLE REJECTION
Ripple rejection is a function of the open loop gain within the feed-back loop (refer to Figure 16 and Figure 17).
The LM1084 exhibits 75dB of ripple rejection (typ.). When adjusted for voltages higher than VREF, the ripple
rejection decreases as function of adjustment gain: (1+R1/R2) or VO/VREF. Therefore a 5V adjustment decreases
ripple rejection by a factor of four (−12dB); Output ripple increases as adjustment voltage increases.
However, the adjustable version allows this degradation of ripple rejection to be compensated. The adjust
terminal can be bypassed to ground with a capacitor (CADJ). The impedance of the CADJ should be equal to or
less than R1 at the desired ripple frequency. This bypass capacitor prevents ripple from being amplified as the
output voltage is increased.
1/(2π*fRIPPLE*CADJ) ≤ R1
LOAD REGULATION
The LM1084 regulates the voltage that appears between its output and ground pins, or between its output and
adjust pins. In some cases, line resistances can introduce errors to the voltage across the load. To obtain the
best load regulation, a few precautions are needed.
Figure 18 shows a typical application using a fixed output regulator. Rt1 and Rt2 are the line resistances. VLOAD
is less than the VOUT by the sum of the voltage drops along the line resistances. In this case, the load regulation
seen at the RLOAD would be degraded from the data sheet specification. To improve this, the load should be tied
directly to the output terminal on the positive side and directly tied to the ground terminal on the negative side.
Figure 18. Typical Application using Fixed Output Regulator
When the adjustable regulator is used (Figure 19), the best performance is obtained with the positive side of the
resistor R1 tied directly to the output terminal of the regulator rather than near the load. This eliminates line drops
from appearing effectively in series with the reference and degrading regulation. For example, a 5V regulator with
0.05Ω resistance between the regulator and load will have a load regulation due to line resistance of 0.05Ω x IL.
If R1 (=125Ω) is connected near the load the effective line resistance will be 0.05Ω (1 + R2/R1) or in this case, it
is 4 times worse. In addition, the ground side of the resistor R2 can be returned near the ground of the load to
provide remote ground sensing and improve load regulation.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM1084
9
LM1084
SNVS037F – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
Figure 19. Best Load Regulation using Adjustable Output Regulator
PROTECTION DIODES
Under normal operation, the LM1084 regulator does not need any protection diode. With the adjustable device,
the internal resistance between the adjustment and output terminals limits the current. No diode is needed to
divert the current around the regulator even with a capacitor on the adjustment terminal. The adjust pin can take
a transient signal of ±25V with respect to the output voltage without damaging the device.
When an output capacitor is connected to a regulator and the input is shorted, the output capacitor will discharge
into the output of the regulator. The discharge current depends on the value of the capacitor, the output voltage
of the regulator, and rate of decrease of VIN. In the LM1084 regulator, the internal diode between the output and
input pins can withstand microsecond surge currents of 10A to 20A. With an extremely large output capacitor
(≥1000 µf), and with input instantaneously shorted to ground, the regulator could be damaged. In this case, an
external diode is recommended between the output and input pins to protect the regulator, shown in Figure 20.
Figure 20. Regulator with Protection Diode
OVERLOAD RECOVERY
Overload recovery refers to regulator's ability to recover from a short circuited output. A key factor in the recovery
process is the current limiting used to protect the output from drawing too much power. The current limiting circuit
reduces the output current as the input to output differential increases. Refer to short circuit curve in the Typical
Performance Characteristics section.
During normal start-up, the input to output differential is small since the output follows the input. But, if the output
is shorted, then the recovery involves a large input to output differential. Sometimes during this condition the
current limiting circuit is slow in recovering. If the limited current is too low to develop a voltage at the output, the
voltage will stabilize at a lower level. Under these conditions it may be necessary to recycle the power of the
regulator in order to get the smaller differential voltage and thus adequate start up conditions. Refer to Typical
Performance Characteristics section for the short circuit current vs. input differential voltage.
10
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM1084
LM1084
www.ti.com
SNVS037F – SEPTEMBER 1999 – REVISED MARCH 2013
THERMAL CONSIDERATIONS
ICs heats up when in operation, and power consumption is one factor in how hot it gets. The other factor is how
well the heat is dissipated. Heat dissipation is predictable by knowing the thermal resistance between the IC and
ambient (θJA). Thermal resistance has units of temperature per power (C/W). The higher the thermal resistance,
the hotter the IC.
The LM1084 specifies the thermal resistance for each package as junction to case (θJC). In order to get the total
resistance to ambient (θJA), two other thermal resistance must be added, one for case to heat-sink (θCH) and one
for heatsink to ambient (θHA). The junction temperature can be predicted as follows:
TJ = TA + PD (θJC + θCH + θHA) = TA + PD θJA
TJ is junction temperature, TA is ambient temperature, and PD is the power consumption of the device. Device
power consumption is calculated as follows:
IIN = IL + IG
PD = (VIN−VOUT) IL + VINIG
Figure 21 shows the voltages and currents which are present in the circuit.
Figure 21. Power Dissipation Diagram
Once the devices power is determined, the maximum allowable (θJA (max)) is calculated as:
θJA
(max)
= TR(max)/PD = TJ(max) − TA(max)/PD
The LM1084 has different temperature specifications for two different sections of the IC: the control section and
the output section. The Electrical Characteristics table shows the junction to case thermal resistances for each of
these sections, while the maximum junction temperatures (TJ(max)) for each section is listed in the Absolute
Maximum Ratings section of the datasheet. TJ(max) is 125°C for the control section, while TJ(max) is 150°C for the
output section.
θJA
(max)
should be calculated separately for each section as follows:
θJA (max, CONTROL SECTION) = (125°C - TA(max))/PD
θJA (max, OUTPUT SECTION) = (150°C - TA(max))/PD
The required heat sink is determined by calculating its required thermal resistance (θHA (max)).
θHA (max) = θJA (max) − (θJC + θCH)
(θHA (max)) should also be calculated twice as follows:
(θHA (max)) = θJA (max, CONTROL SECTION) - (θJC (CONTROL SECTION) + θCH)
(θHA (max)) = θJA(max, OUTPUT SECTION) - (θJC (OUTPUT SECTION) + θCH)
If thermal compound is used, θCH can be estimated at 0.2 C/W. If the case is soldered to the heat sink, then a
θCH can be estimated as 0 C/W.
After, θHA (max) is calculated for each section, choose the lower of the two θHA
appropriate heat sink.
(max)
values to determine the
If PC board copper is going to be used as a heat sink, then Figure 22 can be used to determine the appropriate
area (size) of copper foil required.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM1084
11
LM1084
SNVS037F – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
Figure 22. Heat sink thermal Resistance vs Area
Typical Applications
12
Figure 23. 5V to 3.3V, 5A Regulator
Figure 24. Adjustable @ 5V
Figure 25. 1.2V to 15V Adjustable Regulator
Figure 26. 5V Regulator with Shutdown
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM1084
LM1084
www.ti.com
SNVS037F – SEPTEMBER 1999 – REVISED MARCH 2013
Figure 27. Battery Charger
Figure 28. Adjustable Fixed Regulator
Figure 29. Regulator with Reference
Figure 30. High Current Lamp Driver Protection
Figure 31. Battery Backup Regulated Supply
Figure 32. Ripple Rejection Enhancement
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM1084
13
LM1084
SNVS037F – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
Figure 33. Automatic Light control
Figure 34. Generating Negative Supply voltage
Figure 35. Remote Sensing
14
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM1084
LM1084
www.ti.com
SNVS037F – SEPTEMBER 1999 – REVISED MARCH 2013
REVISION HISTORY
Changes from Revision F (March 2013) to Revision G
Page
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM1084
15
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
LM1084IS-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTT
3
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM1084
IS-3.3
LM1084IS-5.0/NOPB
ACTIVE
DDPAK/
TO-263
KTT
3
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM1084
IS-5.0
LM1084IS-ADJ
ACTIVE
DDPAK/
TO-263
KTT
3
45
TBD
Call TI
Call TI
-40 to 125
LM1084
IS-ADJ
LM1084IS-ADJ/NOPB
ACTIVE
DDPAK/
TO-263
KTT
3
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM1084
IS-ADJ
LM1084ISX-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTT
3
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM1084
IS-3.3
LM1084ISX-5.0/NOPB
ACTIVE
DDPAK/
TO-263
KTT
3
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM1084
IS-5.0
LM1084ISX-ADJ/NOPB
ACTIVE
DDPAK/
TO-263
KTT
3
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LM1084
IS-ADJ
LM1084IT-3.3/NOPB
ACTIVE
TO-220
NDE
3
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LM1084
IT-3.3
LM1084IT-5.0/NOPB
ACTIVE
TO-220
NDE
3
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LM1084
IT-5.0
LM1084IT-ADJ/NOPB
ACTIVE
TO-220
NDE
3
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LM1084
IT-ADJ
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
(3)
11-Apr-2013
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Mar-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM1084ISX-3.3/NOPB
DDPAK/
TO-263
KTT
3
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LM1084ISX-5.0/NOPB
DDPAK/
TO-263
KTT
3
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LM1084ISX-ADJ/NOPB
DDPAK/
TO-263
KTT
3
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Mar-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM1084ISX-3.3/NOPB
DDPAK/TO-263
KTT
3
500
367.0
367.0
45.0
LM1084ISX-5.0/NOPB
DDPAK/TO-263
KTT
3
500
367.0
367.0
45.0
LM1084ISX-ADJ/NOPB
DDPAK/TO-263
KTT
3
500
367.0
367.0
45.0
Pack Materials-Page 2
MECHANICAL DATA
NDE0003B
www.ti.com
MECHANICAL DATA
KTT0003B
TS3B (Rev F)
BOTTOM SIDE OF PACKAGE
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
Similar pages