Minmax ADF-07S15 Ac/dc power module 7w Datasheet

ADF-07 SERIES
AC/DC Power Module 7W
FEATURES
►Fully Encapsulated Plastic Case for PCB Mounting
►Universal Input 85~264VAC, 47~440Hz
►Protection Class II as per IEC/EN 60536
►I/O Isolation 3000VAC with Reinforced Insulation
►Operating Ambient Temp. Range -25℃ to +70℃
►Overload/Voltage and Short Circuit Protection
►Designed-in EMI Emission meets EN55011/22 Class B & FCC Level B
►Designed-in EMC Immunity meets EN61000-4-2,3,4,5,6,8,11
►Eco Design, Compliant to Energy Star Specification and
ErP Directive 2009/125/EC
►UL/cUL/IEC/EN 60950-1 Safety Approval & CE Marking
PRODUCT OVERVIEW
The MINMAX ADF-07 series is a new range of fully encapsulated AC/DC power supply modules. They are designed for direct PCB mounting with solder
pins. The product features EMI-filter to EN55022, class B and EMS compliance to the EN 61000-4 standard. Universal input voltage 85-264VAC and
International safety approvals qualifies these power modules for applications in products with worldwide markets.
The ADF-07 series provide a cost effective solution for many space critical applications in commercial and industrial electronic equipment.
Model Selection Guide
Model
Number
Output
Voltage
Output Current
Input Current
Max.
mA
1400
1400
583
466
291
115VAC, 60Hz
@Max. Load
mA(typ.)
96
139
130
130
130
VDC
3.3
5
12
15
24
ADF-07S03
ADF-07S05
ADF-07S12
ADF-07S15
ADF-07S24
Max. capacitive
Load
Efficiency
(typ.)
@Max. Load
%
70
73
78
78
78
μF
2200
2200
1000
1000
680
Input Specifications
Parameter
Input Voltage Range
Input Frequency Range
Input Voltage Range
No-Load Power Consumption
Model
All Models
115VAC
230VAC
Inrush Current
Cold Start at 25℃
External Fuse (Recommended)
Min.
85
47
120
-------
All Models
Typ.
Max.
--264
--440
--370
--0.3
--10
--20
1.5A Slow – Blow Type
Unit
VAC
Hz
VDC
W
A
A
Output Specifications
Parameter
Output Voltage Setting Accuracy
Line Regulation
Load Regulation
Conditions
Vin=Min. to Max. @Full Load
Io=Min. to Max.
Ripple & Noise
0-20 MHz Bandwidth
Minimum Load
Over Voltage Protection
Temperature Coefficient
Overshoot
Zener diode clamp
Foldback, auto-recovery
105
(long term overload condition may cause damage)
Hiccup mode, Automatic Recovery
Current Limitation
Short Circuit Protection
E-mail:[email protected]
2016/08/30
REV:17
3.3 & 5.0VDC Output Models
Other Output Models
Min.
-------------------
Tel:886-6-2923150
Page 1 of 3
Typ.
±1.0
±0.5
±0.5
1.5
0.8
10
120
±0.01
---
Max.
±2.0
±1.0
±1.0
1.8
1.0
----±0.02
5
Unit
%Vnom.
%
%
%VPP of Vo
%VPP of Vo
%Inom.
% of Vo
%/℃
% Vout
---
---
%Inom.
ADF-07 SERIES
AC/DC POWER MODULE 7W
General Specifications
Parameter
I/O Isolation Voltage
I/O Isolation Resistance
Switching Frequency
Hold-up Time
MTBF (calculated)
Protection Class II
Safety Approvals
Conditions
Input to Output, 60 Seconds
500 VDC
Min.
3000
100
-----
Typ.
----100
20
330,000
Max.
---------
Unit
VACrms
MΩ
KHz
ms
Hours
Typ.
----0.263
142
67
---
Max.
+70
+85
----95
℃
℃
W/℃
℃
℃
% rel. H
---
260
℃
MIL-HDBK-217F@25℃, Ground Benign
According IEC/EN 60536
UL/cUL 60950-1 recognition(UL certificate) , IEC/EN 60950-1(CB-report)
Environmental Specifications
Parameter
Conditions
Operating Ambient Temperature Range
Storage Temperature Range
Power Derating
Min.
-25
-40
Natural Convection
+50℃ to +70℃
Shutdown, Internal IC Junction Temperature
Automatic Recovery, Internal IC Junction Temperature
Thermal Shutdown
------Natural Convection
---
Humidity (non condensing)
Cooling
Lead Temperature (1.5mm from case for 10Sec.)
Unit
EMC Specifications
Parameter
Standards & Level
Conduction and Radiation
EN55014-2 ,EN55024
ESD
Radiated immunity
Fast transient
Surge
Conducted immunity
PFMF
Dips
Interruptions
EMI
EMS
Performance
EN55014-1, EN55022, FCC part 15
Class B
EN61000-4-2 Air ± 8kV , Contact ± 4kV
EN61000-4-3 10V/m
EN61000-4-4 ±2kV
EN61000-4-5 ±1kV
EN61000-4-6 10Vrms
EN61000-4-8 30A/m
EN61000-4-11 30% 10ms
EN61000-4-11 >95% 5000ms
B
A
B
B
B
A
B
C
Notes
1
2
3
4
5
Specifications typical at Ta=+25℃, resistive load, 115VAC, 60Hz input voltage and after warm-up time rated output current unless otherwise noted.
These power modules require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage the power
supplies however they may not meet all listed specifications.
We recommend to protect the converter by a slow blow fuse in the input supply line.
Other input and output voltage may be available, please contact factory.
Specifications are subject to change without notice
E-mail:[email protected]
2016/08/30
REV:17
Tel:886-6-2923150
Page 2 of 3
ADF-07 SERIES
AC/DC POWER MODULE 7W
Package Specifications
Mechanical Dimensions
Pin Connections
6.0 [0.24]
10.16
[0.40]
0.7 [0.03]
Function
1
AC(N) – AC Neutral
2
AC(L) – AC Line
3
+Vout
4
-Vout
5.0 [0.20]
1
Pin
50.8 [2.00]
Bottom View
2
1.00
[ 0.04]
3
45.72 [1.80]
4
19.5 [0.77]
►All dimensions in mm
►Tolerance: ±0.5
20.32 [0.80]
►Pin
25.4 [1.00]
(inches)
(±0.02)
diameter  1.0 ±0.1 (0.04±0.004)
Physical Characteristics
Case Size
:
50.8x25.4x19.5mm (2.00x1.00x0.77 Inches)
Case Material
:
Plastic resin (flammability to UL 94V-0 rated)
Weight
:
44g
Minmax Technology Co., Ltd.
18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan
Tel: 886-6-2923150 Fax: 886-6-2923149 E-mail: [email protected]
2016/08/30
REV:17
Page 3 of 37
Similar pages