ERL (Military RLR) www.vishay.com Vishay Dale Metal Film Resistors, Military/Established Reliability, MIL-PRF-39017 Qualified, Type RLR FEATURES • Meets requirements of MIL-PRF-39017 • Failure rate: Verified failure rate (contact factory for current level) • Epoxy coated construction provides superior moisture protection • Traceability of materials and processing • Monthly lot acceptance testing • Very low noise (-40 dB) • Extensive stocking program at distributors and factory in ± 1 % and ± 2 % tolerances • Vishay Dale has complete capability to develop specific reliability programs designed to customer requirements STANDARD ELECTRICAL SPECIFICATIONS MIL-PRF-39017 STYLE MIL SPEC. SHEET POWER RATING 70 °C W ERL05, ERL05..19 (3) RLR05 05 0.125 ERL07, ERL07..23 (3) RLR07 01 0.25 VISHAY DALE MODEL RESISTANCE RANGE (1) 4.7 to 301K 302K to 1M 1 to 9.76 10 to 3.01M 3.02M to 10M TOLERANCE ±% TEMPERATURE COEFFICIENT ± ppm/°C MAXIMUM WORKING VOLTAGE (4) V 1, 2 100 200 1, 2 100 250 LIFE FAILURE RATE (2) M, P, R, S M, P, R M M, P, R, S M, P, R ERL20, RLR20 02 0.50 4.3 to 3.01M 1, 2 100 350 M, P, R, S ERL20..11 (3) ERL32, RLR32 03 1.0 1 to 2.7M 1, 2 100 500 M, P, R ERL32..1 (3) Notes (1) Extended Resistance Range: DSCC has created a series of drawings intended to support extended resistance ranges left otherwise void by the discontinuation of MIL-R-39008 RCR carbon composition resistors. Vishay Dale is listed as a resource on these drawings as follows: MAXIMUM DSCC POWER RATING RESISTANCE TEMPERATURE VISHAY DALE TOLERANCE WORKING DRAWING P70 °C RANGE COEFFICIENT MODEL ±% VOLTAGE NUMBER W ± ppm/°C V (4) 98020 ERL05..36, ERL05..37 (3) 0.125 1.1M to 22M 2, 5, 10 350 200 0.25 11M to 22M 2, 5, 10 350 250 99011 ERL07..100, ERL07..101 (3) 0.50 3.3M to 22M 2, 5, 10 350 350 98021 ERL20..36, ERL20..37 (3) 1.0 3M to 22M 2, 5, 10 350 350 98022 ERL32..36, ERL32..37 (3) 10 to 2.7M 100 2.0 1, 2, 5, 10 500 97004 ERL62..1, ERL62..2 (3) 350 3M to 22M • Low inductance: DSCC has created a drawing intended to support a resistor which exhibits low inductance over a frequency range of 1 MHz to 30 MHz. Vishay Dale is listed as a resource on these drawings as follows: DSCC DRAWING NUMBER RESISTANCE RANGE MAXIMUM INDUCTANCE nH TOLERANCE ±% TEMPERATURE COEFFICIENT ± ppm/°C MAXIMUM WORKING VOLTAGE V (4) 1 to 10 10 1, 2 100 250 11 to 49.9 8 These drawings can be viewed at: http://www.landandmaritime.dla.mil/Programs/MilSpec/ListDwgs.aspx?DocTYPE=DSCCdwg Consult factory for current QPL failure rates Hot solder dipped leads Continuous working voltage shall be P x R or maximum working voltage, whichever is less. 96002 (2) (3) (4) POWER RATING P70 °C W VISHAY DALE MODEL ERL07..62 0.25 TECHNICAL SPECIFICATIONS PARAMETER Voltage Coefficient, max. Dielectric Strength Insulations Resistance Operating Temperature Range Terminal Strength Solderability Weight Revision: 25-Aug-15 UNIT ppm/V VAC °C lb g CONDITION 5/V when measured between 10 % and full rated voltage RLR05 = 300; RLR07 and RLR20 = 500; RLR32 = 1000 109 min. dry; 1011 min. after moisture test -65 to +150 2 lb pull test on RLR05; 5 lb pull test on all other sizes Continuous satisfactory coverage when tested in accordance with MIL-STD-202, method 208 RLR05 = 0.11; RLR07 = 0.35; RLR20 = 0.75; RLR32 = 1.05 Document Number: 31023 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 ERL (Military RLR) www.vishay.com Vishay Dale GLOBAL PART NUMBER INFORMATION New Global Part Numbering: RLR07C3001FRR36 (preferred part numbering format) R L R 0 7 MIL STYLE LEAD MATERIAL RLR05 RLR07 RLR20 RLR32 C = solderable/ weldable C 3 0 0 1 RESISTANCE VALUE TOLERANCE CODE 3 digit significant figure, followed by a multiplier Use “R” for values < 100 1R00 = 1 3302 = 33 k 1005 = 10 M F=±1% G=±2% F R FAILURE RATE R 3 6 PACKAGING SPECIAL M = 1.0 %/1000 h B14 = tin/lead, bulk Blank = standard P = 0.1 %/1000 h BSL = tin/lead, bulk, (Dash number) R = 0.01 %/1000 h single lot date code (Up to 3 digits) S = 0.001 %/1000 h From 1 to 999 R36 = tin/lead, as applicable T/R (full, except 32’s) 1 = hot solder R64 = tin/lead, dip (32’s) T/R (full; 32’s only) 11 = hot solder RE6 = tin/lead, dip (20’s) T/R (1000 pieces) 19 = hot solder RSL = tin/lead, T/R, dip (05’s) single lot date code 23 = hot solder dip (07’s) Historical Part Number Example: RLR07C3001FR (will continue to be accepted) RLR07 C 3001 F R R36 MIL STYLE LEAD MATERIAL RESISTANCE VALUE TOLERANCE CODE FAILURE RATE PACKAGING Note • For additional information on packaging, refer to the Through Hole Resistor Packaging document (www.vishay.com/doc?31544). DIMENSIONS in inches (millimeters) E (1) A C (Max.) D B Note (1) Lead length for product in bulk pack. For product supplied in tape and reel, the actual lead length would be based on the body size, tape spacing and lead trim. VISHAY DALE MODEL ERL05 ERL07 ERL20 ERL32 ERL62 A B 0.150 ± 0.020 (3.81 ± 0.51) 0.250 + 0.031 - 0.046 (6.35 + 0.79 - 1.17) 0.375 ± 0.041 (9.53 ± 1.04) 0.562 ± 0.031 (14.27 ± 0.79) 0.562 + 0.031 - 0.042 (14.27 + 0.79 - 1.07) 0.066 ± 0.008 (1.68 ± 0.21) 0.090 ± 0.008 (2.29 ± 0.21) 0.138 ± 0.023 (3.51 ± 0.58) 0.190 ± 0.015 (4.83 ± 0.38) 0.230 ± 0.015 (5.84 ± 0.38) C (Max.) 0.187 (4.75) 0.300 (7.62) 0.450 (11.43) 0.625 (15.87) 0.650 (16.51) D E 0.016 ± 0.002 (0.41 ± 0.05) 0.025 ± 0.002 (0.64 ± 0.05) 0.032 ± 0.002 (0.81 ± 0.05) 0.032 + 0.002 - 0.001 (0.81 + 0.05 - 0.03) 0.032 + 0.002 - 0.001 (0.81 + 0.05 - 0.03) 1.25 ± 0.266 (31.75 ± 6.76) 1.50 ± 0.125 (38.10 ± 3.18) 1.50 ± 0.125 (38.10 ± 3.18) 1.50 ± 0.125 (38.10 ± 3.18) 1.50 ± 0.125 (38.10 ± 3.18) MATERIAL SPECIFICATIONS APPLICABLE MIL-SPECIFICATIONS Element Vacuum-deposited nickel-chrome alloy Core Fire-cleaned high purity ceramic Encapsulation Specially formulated epoxy compound Termination Standard lead material is solder-coated copper. Solderable and weldable per MIL-STD-1276, Type C. MIL-PRF-39017: The ERL series meets the electrical, environmental and dimensional requirements of MIL-PRF-39017. MIL-PRF-22684: MIL-PRF-39017 supercedes MIL-PRF-22684 on new designs. The ERL series meet or exceed MIL-PRF-22684 requirements. Documentation: Qualification and failure rate verfication test data is maintained by Vishay Dale and is available upon request. Lot traceability and identification data is maintained by Vishay Dale for five years. POWER RATING Power ratings are based on the following two conditions: 1. ± 2.0 % maximum R in 2000 h load life 2. +150 °C maximum operating temperature Revision: 25-Aug-15 CAGE CODE: 91637 Document Number: 31023 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 ERL (Military RLR) 120 Vishay Dale ERL05 ERL07 100 ERL20 80 ERL32 60 RATED POWER IN % HEAT RISE (°C ABOVE AMBIENT) www.vishay.com 120 100 80 60 40 40 20 20 0 - 65 - 50 - 25 0 0 0.125 0.25 0.375 0.5 0.625 THERMAL RESISTANCE 0.75 0.875 1 1.125 APPLIED POWER IN W 0 25 50 DERATING 75 100 125 150 175 200 70 AMBIENT TEMPERATURE IN °C MARKING (per MIL-PRF-39017) Tolerance: F = 1 %, G = 2 % Value = three significant figures and multiplier J = JAN (Joint Army - Navy) brand RLR05: (3 lines) RLR07: (4 lines) 210A 3-digit date code and lot code 214AJ 3-digit date code, lot code and JAN 1002 Value RLR7C Style (“0” omitted) and lead material FSJD Tolerance, failure rate, JAN and manufacturer’s code 1300G Value and tolerance RD Failure rate and manufacturer’s code RLR20, RLR32: (4 lines) 91637 CAGE code RLR20C Style and lead material 4993FR Value, tolerance and failure rate 1225AJ 4-digit date code, lot code and JAN Revision: 25-Aug-15 Document Number: 31023 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000