NTJD4401N Small Signal MOSFET 20 V, Dual N-Channel, SC-88 ESD Protection Features •Small Footprint (2 x 2 mm) •Low Gate Charge N-Channel Device •ESD Protected Gate •Same Package as SC-70 (6 Leads) •Pb-Free Packages are Available http://onsemi.com V(BR)DSS RDS(on) Typ 0.22 W @ 4.5 V 0.32 W @ 2.5 V 20 V Applications •Load Power switching •Li-Ion Battery Supplied Devices •Cell Phones, Media Players, Digital Cameras, PDAs •DC-DC Conversion SC-88 (SOT-363) Symbol Value Unit Drain-to-Source Voltage VDSS 20 V Gate-to-Source Voltage VGS ±12 V ID 0.63 A Parameter Continuous Drain Current (Based on RqJA) Steady State Power Dissipation (Based on RqJA) Steady State TA = 25°C Continuous Drain Current (Based on RqJL) Steady State TA = 25°C Power Dissipation (Based on RqJL) Steady State TA = 25°C TA = 85°C 0.46 PD ID TA = 25°C 0.55 G1 2 5 G2 D2 3 4 S2 IDM ±1.2 A TJ, TSTG -55 to 150 °C Continuous Source Current (Body Diode) IS 0.63 A Lead Temperature for Soldering Purposes (1/8” from case for 10 s) TL 260 °C t ≤10 ms MARKING DIAGRAM & PIN ASSIGNMENT W 0.29 D1 G2 S2 THERMAL RESISTANCE RATINGS (Note 1) Symbol Typ Max Units Junction-to-Ambient – Steady State RqJA 400 460 °C/W Junction-to-Lead (Drain) – Steady State RqJL 194 226 Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Surface mounted on FR4 board using 1 oz Cu area = 0.9523 in sq. January, 2008 - Rev. 4 D1 A PD TA = 85°C © Semiconductor Components Industries, LLC, 2008 6 Top View 0.91 0.65 Parameter 1 0.14 TA = 85°C Operating Junction and Storage Temperature S1 W 0.27 TA = 85°C 0.775 A 0.51 W @ 1.8 V MAXIMUM RATINGS (TJ = 25°C unless otherwise stated) Pulsed Drain Current ID Max 1 1 SC-88/SOT-363 CASE 419B STYLE 28 6 TD MG G 1 S1 G1 D2 TD M G = Device Code = Date Code = Pb-Free Package (Note: Microdot may be in either location) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. Publication Order Number: NTJD4401N/D NTJD4401N ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise stated) Symbol Test Condition Min Typ Drain-to-Source Breakdown Voltage V(BR)DSS VGS = 0 V, ID = 250 mA 20 27 V Drain-to-Source Breakdown Voltage Temperature Coefficient V(BR)DSS/TJ 22 mV/ °C Parameter Max Unit OFF CHARACTERISTICS Zero Gate Voltage Drain Current IDSS VGS = 0 V, VDS = 16 V 1.0 mA Gate-to-Source Leakage Current IGSS VDS = 0 V, VGS = ±12 V 10 mA VGS(TH) VGS = VDS, ID = 250 mA ON CHARACTERISTICS (Note 2) Gate Threshold Voltage Gate Threshold Temperature Coefficient Drain-to-Source On Resistance VGS(TH)/TJ RDS(on) Forward Transconductance gFS 0.6 0.92 1.5 V mV/ °C -2.1 VGS = 4.5 V, ID = 0.63 A 0.29 0.375 VGS = 2.5 V, ID = 0.40 A 0.36 0.445 VDS = 4.0 V, ID = 0.63 A 2.0 W S CHARGES AND CAPACITANCES CISS Input Capacitance Output Capacitance Reverse Transfer Capacitance COSS VGS = 0 V, f = 1.0 MHz, VDS = 20 V 33 46 13 22 CRSS 2.8 5.0 Total Gate Charge QG(TOT) 1.3 3.0 Threshold Gate Charge QG(TH) Gate-to-Source Charge QGS Gate-to-Drain Charge QGD 0.4 td(ON) 0.083 VGS = 4.5 V, VDS = 10 V, ID = 0.63 A pF nC 0.1 0.2 SWITCHING CHARACTERISTICS (Note 3) Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time tr td(OFF) VGS = 4.5 V, VDD = 10 V, ID = 0.5 A, RG = 20 W tf ms 0.227 0.786 0.506 DRAIN-SOURCE DIODE CHARACTERISTICS Forward Diode Voltage Reverse Recovery Time VSD tRR VGS = 0 V, IS =0.23 A TJ = 25°C 0.76 TJ = 125°C 0.63 VGS = 0 V, dIS/dt = 100 A/ms, IS = 0.63 A 2. Pulse Test: pulse width ≤ 300 ms, duty cycle ≤ 2%. 3. Switching characteristics are independent of operating junction temperatures. http://onsemi.com 2 0.410 1.1 V ms NTJD4401N TYPICAL PERFORMANCE CURVES (TJ = 25°C unless otherwise noted) 1.2 VGS = 4.5 V to 2.2 V 1.2 TJ = 25°C VDS ≥ 10 V VGS = 2 V ID, DRAIN CURRENT (AMPS) ID, DRAIN CURRENT (AMPS) 1.4 1.8 V 1 0.8 1.6 V 0.6 0.4 1.4 V 0.2 1 0.8 0.6 0.4 TJ = 125°C 0.2 25°C 1.2 V 0.7 TJ = -55°C 0 2 4 6 8 10 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) 0 0.4 0.8 1.2 2 1.6 VGS, GATE-TO-SOURCE VOLTAGE (VOLTS) Figure 1. On-Region Characteristics Figure 2. Transfer Characteristics RDS(on), DRAIN-TO-SOURCE RESISTANCE (W) RDS(on), DRAIN-TO-SOURCE RESISTANCE (W) 0 0 VGS = 4.5 V 0.6 0.5 TJ = 125°C 0.4 TJ = 25°C 0.3 TJ = -55°C 0.2 0.1 0 0 0.4 1 0.8 0.6 ID, DRAIN CURRENT (AMPS) 0.2 1.2 1.4 0.7 TJ = 125°C 0.5 0.4 TJ = 25°C 0.3 TJ = -55°C 0.2 0.1 0 0 0.2 0.6 0.4 1 0.8 ID, DRAIN CURRENT (AMPS) 1.4 80 ID = 0.63 A VGS = 4.5 V and 2.5 V TJ = 25°C C, CAPACITANCE (pF) VGS = 0 V 1.6 1.4 1.2 1 60 40 Ciss 20 Coss 0.8 0.6 -50 1.2 Figure 4. On-Resistance vs. Drain Current and Temperature 2 RDS(on), DRAIN-TO-SOURCE RESISTANCE (NORMALIZED) VGS = 2.5 V 0.6 Figure 3. On-Resistance vs. Drain Current and Temperature 1.8 2.4 Crss 0 -25 0 25 50 75 100 125 150 0 5 10 15 TJ, JUNCTION TEMPERATURE (°C) DRAIN-TO-SOURCE VOLTAGE (VOLTS) Figure 5. On-Resistance Variation with Temperature Figure 6. Capacitance Variation http://onsemi.com 3 20 NTJD4401N 0.7 5 QG(TOT) IS, SOURCE CURRENT (AMPS) VGS, GATE-TO-SOURCE VOLTAGE (VOLTS) TYPICAL PERFORMANCE CURVES (TJ = 25°C unless otherwise noted) 4 VGS 3 QGS 2 QGD 1 ID = 0.63 A TJ = 25°C 0 0 0.2 0.4 0.6 0.8 1 Qg, TOTAL GATE CHARGE (nC) 1.2 VGS = 0 V 0.6 0.5 0.4 0.3 0.2 TJ = 150°C 0.1 TJ = 25°C 0 1.4 0 0.2 0.4 0.6 0.8 1 VSD, SOURCE-TO-DRAIN VOLTAGE (VOLTS) Figure 7. Gate-to-Source and Drain-to-Source Voltage vs. Total Charge Figure 8. Diode Forward Voltage vs. Current ORDERING INFORMATION Device NTJD4401NT1 NTJD4401NT1G NTJD4401NT2 NTJD4401NT2G NTJD4401NT4 NTJD4401NT4G Package Shipping† SC-88 3000 / Tape & Reel SC-88 (Pb-Free) 3000 / Tape & Reel SC-88 3000 / Tape & Reel SC-88 (Pb-Free) 3000 / Tape & Reel SC-88 10,000 / Tape & Reel SC-88 (Pb-Free) 10,000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 4 NTJD4401N PACKAGE DIMENSIONS SC-88/SC70-6/SOT-363 CASE 419B-02 ISSUE W NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419B-01 OBSOLETE, NEW STANDARD 419B-02. D e MILLIMETERS DIM MIN NOM MAX A 0.80 0.95 1.10 A1 0.00 0.05 0.10 A3 0.20 REF b 0.10 0.21 0.30 C 0.10 0.14 0.25 D 1.80 2.00 2.20 E 1.15 1.25 1.35 e 0.65 BSC L 0.10 0.20 0.30 HE 2.00 2.10 2.20 STYLE 26: PIN 1. SOURCE 1 2. GATE 1 3. DRAIN 2 4. SOURCE 2 5. GATE 2 6. DRAIN 1 A3 6 5 4 HE C -E1 2 3 L b 6 PL 0.2 (0.008) M E M A INCHES NOM MAX 0.037 0.043 0.002 0.004 0.008 REF 0.004 0.008 0.012 0.004 0.005 0.010 0.070 0.078 0.086 0.045 0.049 0.053 0.026 BSC 0.004 0.008 0.012 0.078 0.082 0.086 MIN 0.031 0.000 SOLDERING FOOTPRINT* A1 0.50 0.0197 0.65 0.025 0.65 0.025 0.40 0.0157 1.9 0.0748 SCALE 20:1 mm Ǔ ǒinches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 5 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NTJD4401N/D