TI1 LM3100 Simple switcherâ® synchronous 1mhz 1.5a step-down voltage regulator Datasheet

LM3100
www.ti.com
SNVS421F – JANUARY 2006 – REVISED DECEMBER 2009
LM3100 SIMPLE SWITCHER® Synchronous 1MHz 1.5A Step-Down Voltage Regulator
Check for Samples: LM3100
FEATURES
1
•
•
•
•
2
•
•
•
•
•
•
•
•
Input voltage range 4.5V - 36V
1.5A output current
0.8V, ±1.5% reference
Integrated 40V, dual N-Channel buck
synchronous switches
Low component count and small solution size
No loop compensation required
Ultra-fast transient response
Stable with ceramic and other low ESR
capacitors
Programmable switching frequency up to
1MHz
Max. duty cycle limited during start-up
Valley current limit
Precision Internal Reference for adjustable
output voltage down to 0.8V
•
•
Thermal shutdown
Thermally enhanced eTSSOP-20 package
TYPICAL APPLICATIONS
•
•
•
•
•
•
•
•
5VDC, 12VDC, 24VDC, 12VAC, and 24VAC
systems
Embedded Systems
Industrial Controls
Automotive Telematics and Body Electronics
Point of Load Regulators
Storage Systems
Broadband Infrastructure
Direct Conversion from 2/3/4 Cell Lithium
Batteries Systems
DESCRIPTION
The LM3100 Synchronously Rectified Buck Converter features all functions needed to implement a highly
efficient, cost effective buck regulator capable of supplying 1.5A to loads with voltages as low as 0.8V. Dual 40V
N-Channel synchronous MOSFET switches allow for low external component thus reducing complexity and
minimizing board space. The LM3100 is designed to work exceptionally well with ceramic and other very low
ESR output capacitors. The Constant ON-Time (COT) regulation scheme requires no loop compensation, results
in fast load transient response, and simplifies circuit implementation. Through the use of a unique design the
regulator does not rely on output capacitor ESR for stability, as do most other COT regulators. The operating
frequency remains nearly constant with line and load variations due to the inverse relationship between the input
voltage and the on-time. The oprating frequency can be externally programmed up to 1MHz. Protection features
include VCC under-voltage lockout, thermal shutdown and gate drive under-voltage lockout. The part is available
in a thermally enhanced eTSSOP-20 package
Typical Application
L
CFB
VOUT
RFB1
CBST
VIN
CIN
CSS
LM3100
RON
N/C
SW
SW
VIN
VIN
BST
GND
SS
N/C
N/C
N/C
N/C
PGND
PGND
VCC
RON
EN
FB
N/C
TST
REN
COUT
RFB2
CVCC
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2009, Texas Instruments Incorporated
LM3100
SNVS421F – JANUARY 2006 – REVISED DECEMBER 2009
www.ti.com
Connection Diagram
1
N/C
2
SW
3
SW
4
VIN
5
VIN
6
BST
7
GND
8
SS
9
N/C
10
N/C
LM3100
EP
20
19
18
17
16
15
14
13
12
11
N/C
N/C
PGND
PGND
VCC
RON
EN
FB
N/C
TST
Figure 1. 20-lead Plastic
eTSSOP
Pin Functions
Pin Descriptions
Pin
Name
Description
1,9,10,12,19,20
N/C
No Connection
Application Information
These pins must be left unconnected.
2, 3
SW
Switching Node
Internally connected to the buck switch source. Connect to
output inductor.
4, 5
VIN
Input supply voltage
Supply pin to the device. Nominal input range is 4.5V to
36V.
6
BST
Connection for bootstrap capacitor
Connect a 0.033µF capacitor from SW pin to this pin. An
internal diode charges the capacitor during the high-side
switch off-time.
7
GND
Analog Ground
8
SS
Soft-start
11
TST
Test mode enable pin
Force the device into test mode. Must be connected to
ground for normal operation.
13
FB
Feedback
Internally connected to the regulation and over-voltage
comparators. The regulation setting is 0.8V at this pin.
Connect to feedback divider.
14
EN
Enable pin
Connect a voltage higher than 1.26V to enable the
regulator.
15
RON
On-time Control
An external resistor from VIN to this pin sets the high-side
switch on-time.
16
VCC
Start-up regulator Output
Nominally regulated to 6V. Connect a capacitor of not less
than 680nF between VCC and GND for stable operation.
17, 18
PGND
Power Ground
Synchronous rectifier MOSFET source connection. Tie to
power ground plane.
DAP
EP
Exposed Pad
Thermal connection pad, connect to GND.
Ground for all internal circuitry other than the synchronous
switches.
An internal 8µA current source charges an external
capacitor to provide the soft- start function.
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2
Submit Documentation Feedback
Copyright © 2006–2009, Texas Instruments Incorporated
Product Folder Links: LM3100
LM3100
www.ti.com
SNVS421F – JANUARY 2006 – REVISED DECEMBER 2009
Absolute Maximum Ratings
(1)
VIN, RON to GND
-0.3V to 40V
SW to GND
-0.3V to 40V
SW to GND (Transient)
-2V (< 100ns)
VIN to SW
-0.3V to 40V
BST to SW
-0.3V to 7V
All Other Inputs to GND
ESD Rating
-0.3V to 7V
(2)
Human Body Model
±2kV
Storage Temperature Range
-65°C to +150°C
Junction Temperature (TJ)
(1)
(2)
150°C
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is intended to be functional. For guaranteed specifications and test conditions, see the Electrical Characteristics.
The human body model is a 100pF capacitor discharged through a 1.5kΩ resistor into each pin.
Operating Ratings
(1)
Supply Voltage Range (VIN)
4.5V to 36V
−40°C to + 125°C
Junction Temperature Range (TJ)
Thermal Resistance (θJC)
(1)
(2)
(2)
6.5°C/W
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is intended to be functional. For guaranteed specifications and test conditions, see the Electrical Characteristics.
θJC measurements are performed in general accordance with Mil-Std 883B, Method 1012.1 and utilizes the copper heat sink technique.
Copper Heat Sink @ 60°C.
Submit Documentation Feedback
Copyright © 2006–2009, Texas Instruments Incorporated
Product Folder Links: LM3100
3
LM3100
SNVS421F – JANUARY 2006 – REVISED DECEMBER 2009
www.ti.com
Electrical Characteristics
Specifications with standard type are for TJ = 25°C only; limits in boldface type apply over the full Operating Junction
Temperature (TJ) range. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical
values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Unless
otherwise stated the following conditions apply: VIN = 18V, VOUT = 3.3V.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
5.0
6.0
7.2
V
50
140
mV
350
570
Start-Up Regulator, VCC
VCC
VIN - VCC
VCC output voltage
CCC = 680nF, no load
VIN - VCC dropout voltage
ICC = 2mA
ICC = 20mA
IVCCL
(1)
VCC = 0V
40
65
VCC under-voltage lockout threshold
(UVLO)
VIN increasing
3.6
3.75
VCC-UVLO-HYS
VCC UVLO hysteresis
VIN decreasing
tVCC-UVLO-D
VCC UVLO filter delay
VCC-UVLO
IIN
IIN-SD
VCC current limit
mA
3.85
130
V
mV
3
µs
IIN operating current
No switching, VFB = 1V
0.7
1
mA
IIN operating current, Device shutdown
VEN = 0V
17
30
µA
0.18
0.35
Ω
0.11
0.2
Ω
3.3
4
V
8
9.8
µA
Switching Characteristics
RDS-UP-ON
Main MOSFET Rds(on)
RDS- DN-ON
Syn. MOSFET Rds(on)
VG-UVLO
Gate drive voltage UVLO
VBST - VSW increasing
SS pin source current
VSS = 0.5V
Soft-start
ISS
6
Current Limit
ICL
Syn. MOSFET current limit threshold
1.9
A
VIN = 10V, RON = 100 kΩ
1.38
µs
VIN = 30V, RON = 100 kΩ
0.47
ON/OFF Timer
tON
tON-MIN
tOFF
ON timer pulse width
ON timer minimum pulse width
200
ns
OFF timer pulse width
260
ns
Enable Input
VEN
VEN-HYS
EN Pin input threshold
VEN rising
Enable threshold hysteresis
VEN falling
1.236
1.26
1.285
90
V
mV
Regulation and Over-Voltage Comparator
VFB
VFB-OV
In-regulation feedback voltage
VSS ≥ 0.8V
TJ = −40°C to + 125°C
0.784
VSS ≥ 0.8V
TJ = 0°C to + 125°C
0.788
Feedback over-voltage threshold
0.894
IFB
0.8
0.816
V
0.812
0.920
0.940
V
5
100
nA
Thermal Shutdown
(1)
4
TSD
Thermal shutdown temperature
TJ rising
165
°C
TSD-HYS
Thermal shutdown temperature
hysteresis
TJ falling
20
°C
VCC provides self bias for the internal gate drive and control circuits. Device thermal limitations limit external loading.
Submit Documentation Feedback
Copyright © 2006–2009, Texas Instruments Incorporated
Product Folder Links: LM3100
LM3100
www.ti.com
SNVS421F – JANUARY 2006 – REVISED DECEMBER 2009
Typical Performance Characteristics
All curves taken at VIN = 18V with configuration in typical application circuit for VOUT = 3.3V shown in this datasheet. TA =
25°C, unless otherwise specified.
Quiescent Current, IIN
vs
VIN
VCC
vs
ICC
1000
7
-40oC
VIN = 36V
6
800
o
25 C
VIN = 7V
5
125 C
VEN = 2V ; VFB = 1V
Active mode, no switching
600
VCC (V)
IIN (PA)
o
VEN = 0V
Shut-down mode
400
125oC
200
3
2
-40oC
25oC
VIN = 18V
4
VCC Externally Loaded
CVCC = 680 nF
1
VFB = 1V, no switching
0
0
0
10
20
30
40
0
20
40
VIN (V)
ICC (mA)
VCC
vs
VIN
TON
vs
VIN
7
60
80
4000
6.5
RON = 100 k:
RON = 100 k:
3000
RON = 50 k:
5.5
TON (ns)
VCC (V)
6
RON = 20 k:
RON = 25 k:
2000
RON = 10 k:
RON = 50 k:
5
1000
VCC not loaded externally
4.5
ILOAD = 700 mA
4
4.5
6
7.5
9
0
10.5
0
5
10
15
VIN (V)
Switching Frequency, FSW
vs
VIN
600
30
ILOAD = 1.5A
0.825
RON = 50 k:
L = 4.7 PH
ILOAD = 0.4A
RON = 50 k:
L = 8.2 PH
ILOAD = 1.5A
ILOAD = 0.5A
RON = 100 k:
L = 14 PH
200
40
VOUT = 3.3V
ILOAD = 0.5A
400
35
0.85
RON = 25 k:
L = 3.8 PH
800
25
VFB
vs
Temperature
VFB (V)
SWITCHING FREQUENCY, FSW (kHz)
1000
20
VIN (V)
VIN = 36V
0.8
VIN = 4.5V
ILOAD = 1.5A
VIN = 18V
0.775
ILOAD = 0.5A
VOUT = 3.3A
0
0
10
20
30
0.75
-50
40
VIN (V)
-20
10
40
70
100
130
TEMPERATURE (ºC)
Submit Documentation Feedback
Copyright © 2006–2009, Texas Instruments Incorporated
Product Folder Links: LM3100
5
LM3100
SNVS421F – JANUARY 2006 – REVISED DECEMBER 2009
www.ti.com
Typical Performance Characteristics (continued)
All curves taken at VIN = 18V with configuration in typical application circuit for VOUT = 3.3V shown in this datasheet. TA =
25°C, unless otherwise specified.
Efficiency
vs
Load Current
(VOUT = 3.3V)
RDS(ON)
vs
Temperature
100
0.4
VIN = 8V
90
EFFICIENCY (%)
RDS(ON) (:)
0.3
Main MOSFET
0.2
0.1
Syn. MOSFET
0
-50
80
VIN = 18V
VIN = 36V
70
60
50
40
-20
10
40
70
100
0
130
0.3
0.6
0.9
1.2
1.5
LOAD CURRENT (A)
TEMPERATURE (ºC)
VOUT Regulation
vs
Load Current
(VOUT = 3.3V)
Efficiency
vs
Load Current
(VOUT = 0.8V)
100
3
90
2
VIN = 4.5V
'VOUT (%)
1
EFFICIENCY (%)
VIN = 8V
VIN = 18V
0
-1
VIN = 36V
-2
80
70
VIN = 12V
60
VIN = 24V
50
VOUT = 0.8V
RON = 30 k:
L = 6.8 PH
VOUT = 3.3V
40
-3
0
0.3
0.6
0.9
1.2
1.5
0
0.3
0.6
0.9
1.2
1.5
LOAD CURRENT (A)
LOAD CURRENT (A)
VOUT Regulation
vs
Load Current
(VOUT = 0.8V)
Power Up
(VOUT = 3.3V, 1.5A Loaded)
3
2
'VOUT (%)
1
VIN = 12V
VIN = 24V
0
-1
VIN = 4.5V
VOUT = 0.8V
-2
RON = 30 k:
L = 6.8 PH
-3
0
0.3
0.6
0.9
1.2
1.5
LOAD CURRENT (A)
6
Submit Documentation Feedback
Copyright © 2006–2009, Texas Instruments Incorporated
Product Folder Links: LM3100
LM3100
www.ti.com
SNVS421F – JANUARY 2006 – REVISED DECEMBER 2009
Typical Performance Characteristics (continued)
All curves taken at VIN = 18V with configuration in typical application circuit for VOUT = 3.3V shown in this datasheet. TA =
25°C, unless otherwise specified.
Enable Transient
(VOUT = 3.3V, 1.5A Loaded)
Shutdown Transient
(VOUT = 3.3V, 1.5A Loaded)
Continuous Mode Operation
(VOUT = 3.3V, 1.5A Loaded)
Discontinuous Mode Operation
(VOUT = 3.3V, 0.15A Loaded)
CCM to DCM Transition
(VOUT = 3.3V, 0.15A - 1.5A Load)
Load Transient
(VOUT = 3.3V, 0.15A - 1.5A Load, Current slew-rate: 2.5A/µs)
Submit Documentation Feedback
Copyright © 2006–2009, Texas Instruments Incorporated
Product Folder Links: LM3100
7
LM3100
SNVS421F – JANUARY 2006 – REVISED DECEMBER 2009
www.ti.com
Simplified Functional Block Diagram
LM 3100
EN
11 EN
VIN
AVDD
6V LDO
4,5 VIN
1.26V
0.92V
0.8V
VREF
VDD
VCC 16
VCC
CIN
THERMAL
SHUTDOWN
UVLO
C VCC
1.26V
GND
R ON
ON TIMER
15 RON
Ron
START
COMPLETE
BST 6
260 ns
OFF TIMER
START
VIN
Gate Drive SD
UVLO
COMPLETE
CBST
VDD
8 PA
DrvH
8 SS
LOGIC
DrvL
CSS
REGULATION
COMPARATOR
0.8V
13 FB
PMOS
input
LEVEL
SHIFT
L
DRIVER
SW 2,3
Vout
VCC
DRIVER
1200
Zero Coil
Current
Detect
CFB *
1
PGND
R FB1
80
R ILIM
0.92V
7
OVER-VOLTAGE
COMPARATOR
CURRENT LIMIT
COMPARATOR
RFB2
200:
32 mV
0.26:
C OUT
PGND 17,18
*optional
Functional Description
The LM3100 Step Down Switching Regulator features all functions needed to implement a cost effective, efficient
buck power converter capable of supplying 1.5A to a load. This voltage regulator contains Dual 40V N-Channel
buck synchronous switches and is available in a thermally enhanced eTSSOP-20 package. The Constant ONTime (COT) regulation scheme requires no loop compensation, results in fast load transient response, and
simplifies circuit implementation. It will work correctly even with an all ceramic output capacitor network and does
not rely on the output capacitor’s ESR for stability. The operating frequency remains constant with line and load
variations due to the inverse relationship between the input voltage and the on-time. The valley current limit
detection circuit, internally set at 1.9A, inhibits the high-side switch until the inductor current level subsides.
Please refer to the functional block diagram with a typical application circuit.
The LM3100 can be applied in numerous applications and can operate efficiently from inputs as high as 36V.
Protection features include: Thermal shutdown, VCC under-voltage lockout, gate drive under-voltage lockout.
Hysteretic Control Circuit Overview
The LM3100 buck DC-DC regulator employs a control scheme in which the high-side switch on-time varies
inversely with the line voltage (VIN). Control is based on a comparator and the one-shot on-timer, with the output
voltage feedback (FB) compared with an internal reference of 0.8V. If the FB level is below the reference the
buck switch is turned on for a fixed time determined by the input voltage and a programming resistor (RON).
Following the on-time, the switch remains off for a minimum of 260ns. If FB is below the reference at that time
the switch turns on again for another on-time period. The switching will continue until regulation is achieved.
The regulator will operate in discontinuous conduction mode at light load currents, and continuous conduction
mode with heavy load current. In discontinuous conduction mode (DCM), current through the output inductor
starts at zero and ramps up to a peak during the on-time, then ramps back to zero before the end of the off-time.
The next on-time period starts when the voltage at FB falls below the internal reference. Until then the inductor
current remains zero and the load is supplied entirely by the output capacitor. In this mode the operating
frequency is lower than in continuous conduction mode, and varies with load current. Conversion efficiency is
maintained since the switching losses are reduced with the reduction in load and switching frequency. The
discontinuous operating frequency can be calculated approximately as follows:
FSW =
8
VOUT (VIN - 1) x L x 1.18 x 1020 x IOUT
(VIN ± VOUT) x RON2
(1)
Submit Documentation Feedback
Copyright © 2006–2009, Texas Instruments Incorporated
Product Folder Links: LM3100
LM3100
www.ti.com
SNVS421F – JANUARY 2006 – REVISED DECEMBER 2009
In continuous conduction mode (CCM), current always flows through the inductor and never reaches zero during
the off-time. In this mode, the operating frequency remains relatively constant with load and line variations. The
CCM operating frequency can be calculated approximately as follows:
FSW =
VOUT
1.3 x 10-10 x RON
(2)
The output voltage is set by two external resistors (RFB1, RFB2). The regulated output voltage is calculated as
follows:
VOUT = 0.8V x (RFB1 + RFB2)/RFB2
(3)
Start-up Regulator (VCC)
The start-up regulator is integrated within LM3100. The input pin (VIN) can be connected directly to line voltage
up to 36V, with transient capability of 40V. The VCC output regulates at 6V, and is current limited to 65 mA. Upon
power up, the regulator sources current into the external capacitor at VCC (CVCC). CVCC must be at least 680nF
for stability. When the voltage on the VCC pin reaches the under-voltage lockout threshold of 3.75V, the buck
switch is enabled and the Soft-start pin is released to allow the soft-start capacitor (CSS) to charge.
The minimum input voltage is determined by the dropout voltage of VCC regulator, and the VCC UVLO falling
threshold (≊3.7 V). If VIN is less than ≊4.0V, the VCC UVLO activates to shut off the output.
Regulation Comparator
The feedback voltage at FB pin is compared to the internal reference voltage of 0.8V. In normal operation (the
output voltage is regulated), an on-time period is initiated when the voltage at FB falls below 0.8V. The buck
switch stays on for the on-time, causing the FB voltage to rise above 0.8V. After the on-time period, the buck
switch stays off until the FB voltage falls below 0.8V again. Bias current at the FB pin is nominally 100 nA.
Over-Voltage Comparator
The voltage at FB pin is compared to an internal 0.92V reference. If the feedback voltage rises above 0.92V the
on-time pulse is immediately terminated. This condition can occur if the input voltage, or the output load, changes
suddenly. Once the OVP is activated, the buck switch remains off until the voltage at FB pin falls below 0.92V.
The low side switch will stay on to discharge the inductor energy until the inductor current decays to zero. The
low side switch will be turned off.
ON-Time Timer, Shutdown
The ON-Time of LM3100 main switch is determined by the RON resistor and the input voltage (VIN), and is
calculated from:
tON =
1.3 x 10-10 x RON
VIN
(4)
The inverse relationship of tON and VIN results in a nearly constant switching frequency as VIN is varied. RON
should be selected for a minimum on-time (at maximum VIN) greater than 200 ns for proper current limit
operation. This requirement limits the maximum frequency for each application, depending on VIN and VOUT,
calculated from equation 5:
VOUT
FSW(MAX)
=
VIN(MAX) x 200 ns
(5)
The LM3100 can be remotely shut down by taking the EN pin below 1.1V. Refer to Figure 2. In this mode the SS
pin is internally grounded, the on-timer is disabled, and bias currents are reduced. Releasing the EN pin allows
normal operation to resume. For normal operation, the voltage at the EN pin is set between 1.5V and 3.0V,
depending on VIN and the external pull-up resistor. For all cases, this voltage must be limited not to exceed 7V.
Submit Documentation Feedback
Copyright © 2006–2009, Texas Instruments Incorporated
Product Folder Links: LM3100
9
LM3100
SNVS421F – JANUARY 2006 – REVISED DECEMBER 2009
www.ti.com
VIN
VIN
LM3100
EN
STOP
RUN
Figure 2. Shutdown Implementation
Current Limit
Current limit detection occurs during the off-time by monitoring the re-circulating current through the low-side
synchronous switch. Referring to Functional Block Diagram, when the buck switch is turned off, inductor current
flows through the load, into PGND, and through the internal low-side synchronous switch. If that current exceeds
1.9A the current limit comparator toggles, forcing a delay to the start of the next on-time period. The next cycle
starts when the re-circulating current falls back below 1.9A and the voltage at FB is below 0.8V. The inductor
current is monitored during the low-side switch on-time. As long as the overload condition persists and the
inductor current exceeds 1.9A, the high-side switch will remain inhibited. The operating frequency is lower during
an over-current due to longer than normal off-times.
Figure 3 illustrates an inductor current waveform, the average inductor current is equal to the output current, IOUT
in steady state. When an overload occurs, the inductor current will increase until it exceeds the current limit
threshold, 1.9A. Then the control keeps the high-side switch off until the inductor current ramps down below
1.9A. Within each on-time period, the current ramps up an amount equal to:
'I =
(VIN - VOUT) x tON
L
(6)
During this time the LM3100 is in a constant current mode, with an average load current (IOCL) equal to 1.9A
+ΔI/2.
IPK
'I
IOCL
Inductor Current
ICL
IOUT
Normal Operation
Load Current
Increases
Current Limited
Figure 3. Inductor Current - Current Limit Operation
N-Channel Buck Switch and Driver
The LM3100 integrates an N-Channel buck (high-side) switch and associated floating high voltage gate driver.
The gate drive circuit works in conjunction with an external bootstrap capacitor and an internal high voltage
diode. A 33 nF capacitor (CBST) connected between BST and SW pins provides voltage to the high-side driver
during the buck switch on-time. During each off-time, the SW pin falls to approximately -1V and CBST charges
from the VCC supply through the internal diode. The minimum off-time of 260ns ensures adequate time each
cycle to recharge the bootstrap capacitor.
10
Submit Documentation Feedback
Copyright © 2006–2009, Texas Instruments Incorporated
Product Folder Links: LM3100
LM3100
www.ti.com
SNVS421F – JANUARY 2006 – REVISED DECEMBER 2009
Soft-Start
The soft-start feature allows the converter to gradually reach a steady state operating point, thereby reducing
start-up stresses and current surges. Upon turn-on, after VCC reaches the under-voltage threshold, an internal
8µA current source charges up the external capacitor at the SS pin. The ramping voltage at SS (and the noninverting input of the regulation comparator) ramps up the output voltage in a controlled manner.
An internal switch grounds the SS pin if any of the following cases happen: (i) VCC falls below the under-voltage
lock-out threshold; (ii) a thermal shutdown occurs; or (iii) the EN pin is grounded. Alternatively, the converter can
be disabled by connecting the SS pin to ground using an external switch. Releasing the switch allows the SS pin
return to pull high and the output voltage returns to normal. The shut-down configuration is shown in Figure 4 .
VIN
VIN
LM3100
SS
STOP
+
RUN
Figure 4. Alternate Shutdown Implementation
Thermal Protection
The LM3100 should be operated so the junction temperature does not exceed the maximum limit. An internal
Thermal Shutdown circuit, which activates (typically) at 165°C, takes the controller to a low power reset state by
disabling the buck switch and the on-timer, and grounding the SS pin. This feature helps prevent catastrophic
failures from accidental device overheating. When the junction temperature falls back below 145°C (typical
hysteresis = 20°C), the SS pin is released and normal operation resumes.
Applications Information
EXTERNAL COMPONENTS
The following guidelines can be used to select the external components.
RFB1 and RFB2 : The ratio of these resistors is calculated from:
RFB1
RFB2
=
VOUT
0.8V
-1
(7)
RFB1 and RFB2 should be chosen from standard value resistors in the range of 1.0 kΩ - 10 kΩ which satisfy the
above ratio.
For VOUT = 0.8V, the FB pin can be connected to the output directly. However, the converter operation needs a
minimum inductor current ripple to maintain good regulation when no load is connected. This minimum load is
about 10 µA and can be implemented by adding a pre-load resistor to the output.
RON: The minimum value for RON is calculated from:
RON t
200 ns x VIN(MAX)
1.3 x 10-10
(8)
The equation 2 in Control Overview section can be used to select RON if a specific frequency is desired as long
as the above limitation is met.
L: The main parameter affected by the inductor is the output current ripple amplitude (IOR). The maximum
allowable (IOR must be determined at both the minimum and maximum nominal load currents. At minimum load
current, the lower peak must not reach 0A. At maximum load current, the upper peak must not exceed the
current limit threshold (1.9A). The allowable ripple current is calculated from the following equations:
Submit Documentation Feedback
Copyright © 2006–2009, Texas Instruments Incorporated
Product Folder Links: LM3100
11
LM3100
SNVS421F – JANUARY 2006 – REVISED DECEMBER 2009
www.ti.com
IOR(MAX1) = 2 x IO(min)
(9)
or
IOR(MAX2) = 2 x (1.9A - IO(max))
(10)
The lesser of the two ripple amplitudes calculated above is then used in the following equation:
L=
VOUT x (VIN - VOUT)
IOR x FS x VIN
(11)
where VIN is the maximum input voltage and Fs is determined from equation 1. This provides a value for L. The
next larger standard value should be used. L should be rated for the IPK current level shown in Figure 3.
Figure 5. Inductor Selector for VOUT = 3.3V
25.0
RON = 100 k:
INDUCTANCE (PH)
20.0
15.0
RON = 50 k:
10.0
5.0
RON = 25 k:
0.0
0
10
20
30
40
VIN (V)
Figure 6. Inductor Selector for VOUT = 0.8V
25
RON = 100 k:
INDUCTANCE (PH)
20
15
RON = 50 k:
10
RON = 25 k:
5
0
0
10
20
30
40
VIN (V)
CVCC: The capacitor on the VCC output provides not only noise filtering and stability, but also prevents false
triggering of the VCC UVLO at the buck switch on/off transitions. For this reason, CVCC should be no smaller than
680 nF for stability, and should be a good quality, low ESR, ceramic capacitor.
CO and CO3: CO should generally be no smaller than 10 µF. Experimentation is usually necessary to determine
the minimum value for CO, as the nature of the load may require a larger value. A load which creates significant
transients requires a larger value for CO than a fixed load.
CO3 is a small value ceramic capacitor to further suppress high frequency noise at VOUT. A 47nF is
recommended, located close to the LM3100.
CIN and CIN3: CIN’s purpose is to supply most of the switch current during the on-time, and limit the voltage ripple
at VIN, assume the voltage source feeding VIN has an output impedance greater than zero. If the source’s
dynamic impedance is high (effectively a current source), CIN supplies the average input current, but not the
ripple current.
12
Submit Documentation Feedback
Copyright © 2006–2009, Texas Instruments Incorporated
Product Folder Links: LM3100
LM3100
www.ti.com
SNVS421F – JANUARY 2006 – REVISED DECEMBER 2009
At maximum load current, when the buck switch turns on, the current into VIN suddenly increases to the lower
peak of the inductor’s ripple current, ramps up to the peak value, then drop to zero at turn-off. The average
current during the on-time is the load current. For a worst case calculation, CIN must supply this average load
current during the maximum on-time. CIN is calculated from:
CIN =
IOUT x tON
'V
(12)
where IOUT is the load current, tON is the maximum on-time, and ΔV is the allowable ripple voltage at VIN.
CIN3’s purpose is to help avoid transients and ringing due to long lead inductance at VIN. A low ESR, 0.1µF
ceramic chip capacitor is recommended, located close to the LM3100.
CBST: The recommended value for CBST is 33 nF. A high quality ceramic capacitor with low ESR is recommended
as CBST supplies a surge current to charge the buck switch gate at turn-on. A low ESR also helps ensure a
complete recharge during each off-time.
CSS: The capacitor at the SS pin determines the soft-start time, i.e. the time for the reference voltage at the
regulation comparator, and the output voltage, to reach their final value. The time is determined from the
following:
tSS =
CSS x 0.8V
8 PA
(13)
CFB: If output voltage is higher than 1.6V, this feedback capacitor is needed for Discontinuous Conduction Mode
to improve the output ripple performance, the recommended value for CFB is 10 nF.
PC BOARD LAYOUT
The LM3100 regulation, over-voltage, and current limit comparators are very fast, and will respond to short
duration noise pulses. Layout considerations are therefore critical for optimum performance. The layout must be
as neat and compact as possible, and all external components must be as close as possible to their associated
pins. Refer to the functional block diagram, the loop formed by CIN, the high and low-side switches internal to the
IC, and the PGND pin should be as small as possible. The PGND connection to Cin should be as short and
direct as possible. There should be several vias connecting the Cin ground terminal to the ground plane placed
as close to the capacitor as possible. The boost capacitor should be connected as close to the SW and BST pins
as possible. The feedback divider resistors and the CFB capacitor should be located close to the FB pin. A long
trace run from the top of the divider to the output is generally acceptable since this is a low impedance node.
Ground the bottom of the divider directly to the GND (pin 7). The output capacitor, COUT, should be connected
close to the load and tied directly into the ground plane. The inductor should connect close to the SW pin with as
short a trace as possible to help reduce the potential for EMI (electro-magnetic interference) generation.
If it is expected that the internal dissipation of the LM3100 will produce excessive junction temperatures during
normal operation, good use of the PC board’s ground plane can help considerably to dissipate heat. The
exposed pad on the bottom of the IC package can be soldered to a ground plane and that plane should extend
out from beneath the IC to help dissipate the heat. The exposed pad is internally connected to the IC substrate.
Additionally the use of thick copper traces, where possible, can help conduct heat away from the IC. Using
numerous vias to connect the die attach pad to an internal ground plane is a good practice. Judicious positioning
of the PC board within the end product, along with the use of any available air flow (forced or natural convection)
can help reduce the junction temperature.
Submit Documentation Feedback
Copyright © 2006–2009, Texas Instruments Incorporated
Product Folder Links: LM3100
13
LM3100
SNVS421F – JANUARY 2006 – REVISED DECEMBER 2009
www.ti.com
CFB CO3
10 nF 47 nF
L 15 PH
VIN = 8V ± 36V
CIN1, CIN2
2 x 10 PF
CIN3
0.1 PF
CSS
10 nF
N/C
SW
SW
VIN
VIN
BST
GND
SS
N/C
N/C
LM3100
RON
100k
CBST
33 nF
N/C
N/C
PGND
PGND
VCC
RON
EN
FB
N/C
TST
REN
200k
VOUT = 3.3V
IOUT = 1.5A
RFB1
6.8k
RFB2
2.2k
CO1, CO2
2 x 22 PF
CVCC
680 nF
Figure 7. Typical Application Schematic for VOUT = 3.3V
CBST
33 nF
VIN = 4.5V ± 24V
CIN1, CIN2
2 x 10 PF
CIN3
0.1 PF
CSS
10 nF
N/C
SW
SW
VIN
VIN
BST
GND
SS
N/C
N/C
LM3100
L 6.8 PH
N/C
N/C
PGND
PGND
VCC
RON
EN
FB
N/C
TST
RON
30k
REN
200k
CO3
47 nF
RFB2
40k
VOUT = 0.8V
IOUT = 1.5A
CO1, CO2
2 x 22 PF
CVCC
680 nF
Figure 8. Typical Application Schematic for VOUT = 0.8V
14
Submit Documentation Feedback
Copyright © 2006–2009, Texas Instruments Incorporated
Product Folder Links: LM3100
PACKAGE OPTION ADDENDUM
www.ti.com
17-Nov-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package Qty
Drawing
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Samples
(3)
(Requires Login)
LM3100MH
ACTIVE
HTSSOP
PWP
20
73
TBD
CU SNPB
Level-1-260C-UNLIM
LM3100MH/NOPB
ACTIVE
HTSSOP
PWP
20
73
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM3100MHX
ACTIVE
HTSSOP
PWP
20
2500
TBD
CU SNPB
Level-1-260C-UNLIM
LM3100MHX/NOPB
ACTIVE
HTSSOP
PWP
20
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Nov-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
LM3100MHX
HTSSOP
PWP
20
2500
330.0
16.4
LM3100MHX/NOPB
HTSSOP
PWP
20
2500
330.0
16.4
Pack Materials-Page 1
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
6.95
7.1
1.6
8.0
16.0
Q1
6.95
7.1
1.6
8.0
16.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Nov-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM3100MHX
HTSSOP
PWP
20
2500
349.0
337.0
45.0
LM3100MHX/NOPB
HTSSOP
PWP
20
2500
349.0
337.0
45.0
Pack Materials-Page 2
MECHANICAL DATA
PWP0020A
MXA20A (Rev C)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
LM3100EVAL