LINER LM285-2.5 Micropower voltage reference Datasheet

LM185-2.5/
LM285-2.5/LM385-2.5
Micropower Voltage
Reference
U
FEATURES
■
■
■
■
DESCRIPTIO
20µA to 20mA Operating Range
Guaranteed 1% Initial Voltage Tolerance
Guaranteed 1Ω Dynamic Impedance
Very Low Power Consumption
The LM185-2.5 is a two-terminal band gap reference
diode that has been designed for applications which
require precision performance with micropower operation. The device provides guaranteed operation specifications at currents as low as 20µA. The nominal voltage is
2.5V with both 1% and 2% tolerances available. Some
additional features are: maximum dynamic impedance of
1Ω, low noise and excellent stability over time and temperature. The advanced design, processing and testing
techniques make Linear’s LM185-2.5 a superior choice
over previous designs. A circuit for cold junction compensation of a thermocouple is shown below.
U
APPLICATIO S
■
■
■
■
■
Portable Meter References
Portable Test Instruments
Battery-Operated Systems
Panel Meters
Current Loop Instrumentation
For applications requiring guaranteed temperature drift,
see the LT1034 data sheet.
, LTC and LT are registered trademarks of Linear Technology Corporation.
U
TYPICAL APPLICATIO
Thermocouple Cold Junction Compensator
Reverse Voltage Change
16
VIN
16k
1M
2 MERCURY
CELLS 2.6V
LM334
100k W.W.
ZERO
V–
RSET
2k
LM385-2.5
950Ω
TYPE K
450Ω
+
–
METER
10k ADJUST
FOR 12.17mV
AT 25°C
ACROSS 450Ω
LM185-2.5 TA01
OUTPUT VOLTAGE CHANGE (mV)
IQ ≈ 50µA
–55°C ≤ TA ≤ +125°C
12
8
4
0
–4
0.01
0.1
1
10
REVERSE CURRENT (mA)
100
LM185-2.5 TA02
1
LM185-2.5/
LM285-2.5/LM385-2.5
W W
W
AXI U
U
ABSOLUTE
RATI GS
(Note 1)
Reverse Breakdown Current ................................ 30mA
Forward Current .................................................. 10mA
Operating Temperature Range
LM185-2.5 (OBSOLETE) ............ –55°C to 125°C
LM285-2.5 ...................................... – 40°C to 85°C
LM385-2.5 ........................................... 0°C to 70°C
Storage Temperature Range
LM185-2.5 (OBSOLETE) ............ – 65°C to 150°C
LM285-2.5 .................................... – 65°C to 150°C
LM385-2.5 .................................... – 65°C to 150°C
Lead Temperature (Soldering, 10 sec.)................ 300°C
U
W
U
PACKAGE/ORDER I FOR ATIO
ORDER PART
NUMBER
BOTTOM VIEW
BOTTOM VIEW
LM185H-2.5
LM285H-2.5
LM385H-2.5
LM385BH-2.5
H PACKAGE
2-LEAD TO-46 METAL CAN
Z PACKAGE
3-LEAD TO-92 PLASTIC
LM285Z-2.5
LM385Z-2.5
LM385BZ-2.5
(NOTE 3)
TJMAX = 100°C, θJA = 160°C/W
(NOTE 3)
TJMAX = 150°C, θJA = 440°C/W, θJC = 80°C/W
ORDER PART
NUMBER
OBSOLETE PACKAGE
Consider the S8 or Z Packages for Alternate Source
ORDER PART
NUMBER
TOP VIEW
NC
1
8
NC
2
7
NC
3
6
4
5
S8 PACKAGE
8-LEAD PLASTIC SO
NC
NC
(DO NOT
USE)
TJMAX = 150°C, θJA = 220°C/W
Consult LTC Marketing for parts specified with wider operating temperature ranges.
2
LM285S8-2.5
LM385S8-2.5
LM385BS8-2.5
S8 PART MARKING
2852
3852
3852B
LM185-2.5/
LM285-2.5/LM385-2.5
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 2)
SYMBOL
PARAMETER
CONDITIONS
VZ
Reverse Breakdown Voltage
TA = 25°C, 20µA ≤ IR ≤ 20mA
LM185-2.5/285-2.5
LM385-2.5
LM385B-2.5 (Note 3)
LM185-2.5/285-2.5
MIN
TYP
MAX
2.462
Average Temperature Coefficient
IMIN
Minimum Operating Current
TMIN ≤ TA ≤ TMAX
●
∆VZ
∆IR
Reverse Breakdown Voltage
Change With Current
20µA ≤ IR ≤ 1mA
TA = 25°C
TMIN ≤ TA ≤ TMAX
●
1mA ≤ IR ≤ 20mA
TA = 25°C
TMIN ≤ TA ≤ TMAX
●
IR = 100µA (Note 4)
TA = 25°C
TMIN ≤ TA ≤ TMAX
●
Reverse Dynamic Impedance
20µA ≤ IR ≤ 20mA (Note 3)
20
8
0.2
UNITS
2.538
2.425
2.462
∆VZ
∆Temp
rZ
2.500
LM385-2.5/385B-2.5
MIN
TYP MAX
V
V
V
2.500 2.575
2.500 2.538
20
ppm/°C
20
µA
1.0
1.5
2.0
2.5
mV
mV
10
20
20
25
mV
mV
1.0
1.5
Ω
Ω
20
0.6
1.5
8
0.4
en
Wide Band Noise (RMS)
10Hz ≤ f ≤ 10kHz, IR = 100µA
120
120
µV
∆VZ
∆Time
Long Term Stability
TA = 25°C ± 0.1°C, IR = 100µA
20
20
ppm/kHr
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: All specifications are for TA = 25°C unless otherwise noted. For the
LM185-2.5 TMIN = – 55°C and TMAX = 125°C. For LM285-2.5, TMIN = –
40°C and TMAX = 85°C. For LM385-2.5, TMIN = 0°C and TMAX = 70°C.
Note 3: For very low initial tolerance, consult LT1004 data sheet. The
LT1004 is a low cost, pin for pin substitution device. For guaranteed
temperature coefficient consult the LT1034-2.5 data sheet.
Note 4: Guaranteed but not tested.
3
LM185-2.5/
LM285-2.5/LM385-2.5
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Reverse Characteristics
Forward Characteristics
TA = 25°C
10
1
2.520
REFERENCE VOLTAGE (V)
FORWARD VOLTAGE (V)
–55°C TO 125°C
REVERSE CURRENT (µA)
Temperature Drift
2.525
1.6
100
1.2
0.8
0.4
2.515
2.510
2.505
2.500
2.495
2.490
2.485
0.1
0.5
0
1.0
1.5
2.0
REVERSE VOLTAGE (V)
2.5
0
0.01
3.0
1
10
0.1
FORWARD CURRENT (mA)
LM185-2.5 • TPC01
Reverse Dynamic Impedance
LM185-2.5 • TPC03
Reverse Dynamic Impedance
Noise Voltage
10k
1400
f = 25Hz
–55°C TO 125°C
10
1
1200
1k
1000
NOISE (nV/√Hz)
DYNAMIC IMPEDANCE (Ω)
TA = 25°C
IR = 100µA
100
5 25 45 65 85 105 125
TEMPERATURE (°C)
LM185-2.5 • TPC02
1000
DYNAMIC IMPEDANCE (Ω)
2.480
–55 –35 –15
100
100
10
800
600
400
1
200
0.1
0.01
1
10
0.1
REVERSE CURRENT (mA)
0.1
100
100
10
10k
1k
FREQUENCY (Hz)
LM185-2.5 • TPC05
100k
0
1M
10
100
1k
10k
FREQUENCY (Hz)
LM185-2.5M • TPC06
LM185-2.5 • TPC05
Filtered Output Noise
Response Time
120
R
4.0
C
80
3.0
VOLTAGE (V)
INTEGRATED NOISE (µVRMS)
100mA
100
60
40
RC LOW PASS
20
OUTPUT
2.0
24k
1.0
VIN
VOUT
0
5V
INPUT
0
100
1k
10k
100k
CUTOFF FREQUENCY (Hz)
LM185-2.5 • TPC07
4
0
0
100k
100
500
TIME (µS)
LM185-2.5 • TPC08
LM185-2.5/
LM285-2.5/LM385-2.5
W
W
SCHE ATIC DIAGRA
+
7.5k
Q13
200k
Q12
Q4
Q3
Q7
20pF
Q11
20pF
Q1
50k
600k
500k
Q10
Q5
Q2
300k
Q9
Q6
100k
Q8
500Ω
Q14
60k
500k
–
LM185-2.5 SD01
U
PACKAGE DESCRIPTIO
H Package
2-Lead and 3-Lead TO-46 Metal Can
(Reference LTC DWG # 05-08-1340)
0.209 – 0.219
(5.309 – 5.537)
0.178 – 0.195
(4.521 – 4.953)
REFERENCE
PLANE
0.085 – 0.105
(2.159 – 2.667)
0.500
(12.700)
MIN
0.100
(2.540)
TYP
0.050
(1.270)
TYP
PIN 1
*
0.016 – 0.021**
(0.406 – 0.533)
DIA
0.050
(1.270)
TYP
FOR 3-LEAD PACKAGE ONLY
0.025
(0.635)
MAX
45°
0.036 – 0.046
(0.914 – 1.168)
0.028 – 0.048
(0.711 – 1.219)
H02/03(TO-46) 1098
*LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE
AND 0.045" BELOW THE REFERENCE PLANE
0.016 – 0.024
**FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS
(0.406 – 0.610)
OBSOLETE PACKAGE
5
LM185-2.5/
LM285-2.5/LM385-2.5
U
PACKAGE DESCRIPTIO
S8 Package
8-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
0.189 – 0.197*
(4.801 – 5.004)
8
7
6
5
0.150 – 0.157**
(3.810 – 3.988)
0.228 – 0.244
(5.791 – 6.197)
SO8 1298
1
0.010 – 0.020
× 45°
(0.254 – 0.508)
0.008 – 0.010
(0.203 – 0.254)
0.053 – 0.069
(1.346 – 1.752)
0°– 8° TYP
0.016 – 0.050
(0.406 – 1.270)
0.014 – 0.019
(0.355 – 0.483)
TYP
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
6
2
3
4
0.004 – 0.010
(0.101 – 0.254)
0.050
(1.270)
BSC
LM185-2.5/
LM285-2.5/LM385-2.5
U
PACKAGE DESCRIPTIO
Z Package
3-Lead Plastic TO-92 (Similar to TO-226)
(Reference LTC DWG # 05-08-1410)
0.180 ± 0.005
(4.572 ± 0.127)
0.060 ± 0.005
(1.524± 0.127)
DIA
0.90
(2.286)
NOM
0.180 ± 0.005
(4.572 ± 0.127)
0.500
(12.70)
MIN
0.050
(1.27)
BSC
0.050 UNCONTROLLED
(1.270) LEAD DIMENSION
MAX
0.016 ± 0.003
(0.406 ± 0.076)
0.060 ± 0.010
(1.524 ± 0.254)
0.140 ± 0.010
(3.556 ± 0.127)
5°
NOM
0.015 ± 0.002
(0.381 ± 0.051)
0.098 +016/–0.04
(2.5 +0.4/–0.1)
2 PLCS
Z3 (TO-92) 0401
TO-92 TAPE AND REEL
REFER TO TAPE AND REEL SECTION OF
LTC DATA BOOK FOR ADDITIONAL INFORMATION
10° NOM
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of circuits as described herein will not infringe on existing patent rights.
7
LM185-2.5/
LM285-2.5/LM385-2.5
UO
TYPICAL APPLICATI
S
V+
9V
3.7V ≤ V + ≤ 30V
LM334
220k
R
2.7k
2.5V
2.5V
LM385-2.5
LM385-2.5
OPERATION OVER A
WIDE SUPPLY RANGE
REFERENCE FROM
A 9V BATTERY
LM185-2.5 TA03
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1634
Micropower Shunt Voltage Reference
0.05% Initial Accuracy, 10ppm/°C Maximum Tempco
Output Voltage: 1.25V, 2.5V, 4.096V and 5V
8
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900
●
FAX: (408) 434-0507
●
www.linear.com
185fc LT/CP 0801 1.5K REV C • PRINTED IN USA
 LINEAR TECHNOLOGY CORPORATION 1992