MTWA26 SERIES 25W Multi-Plug Wall Mount for I.T. Equipment 1 Year Warranty Wide Input Voltage 90 to 264 VAC, 47 to 63Hz Interchangeable AC plug(USA, UK, Europe, Australia) Output Voltage Available From 5VDC Thru 48VDC Single Output Class II Insulation (Double Insulation) Energy Star 2.0, CEC V, and RoHS compliance Approvals: Single Output Product Number MTWA26-S02 MTWA26-S03 MTWA26-S04 MTWA26-S05 MTWA26-S06 MTWA26-S07 MTWA26-S08 MTWA26-S09 MTWA26-S10 MTWA26-S11 Output Voltage 5 ~ 6 VDC 6 ~ 8 VDC 8 ~ 11 VDC 11 ~ 13 VDC 13 ~ 16 VDC 16 ~ 21 VDC 21 ~ 27 VDC 27 ~ 33 VDC 33 ~ 40 VDC 40 ~ 48 VDC Max. Output Current 3.30 ~ 2.75 A 3.33 ~ 2.50 A 2.75 ~ 2.00 A 2.27 ~ 1.92 A 1.92 ~ 1.56 A 1.56 ~ 1.19 A 1.19 ~ 0.92 A 0.92 ~ 0.75 A 0.75 ~ 0.62 A 0.62 ~ 0.52 A Total Regulation 5% 5% 5% 5% 5% 5% 3% 3% 3% 2% Maximum Output Power 16.5W 20W 22W 25W 25W 25W 25W 25W 25W 25W The total regulation on S02~S06 required to use AWG#16× 2C/4FT output cable. The total regulation on S07~S11 required to use AWG#18× 2C/4FT output cable. The regulation and efficiency will be changed by modified output cable. Electrical Characteristics Parameter Input Voltage Input Frequency Output Power Range Input Current (Low Line) Input Current (High Line) Low Line Inrush Current High Line Inrush Current Efficiency Line Regulation Load Regulation Over Voltage Protection Over Current Protection Transient Response Hold-Up Time Start Up Time Ripple & Noise (Peak to Peak) Temperature Coefficient No-load Power Consumption Test Conditions Operating Voltage Vin=100 to 240VAC Io=Full load, Vin=115VAC Io=Full load, Vin=230VAC Io=Full load, 25°C, Cool start, Vin=115VAC Io=Full load, 25°C, Cool start, Vin=230VAC Io=Full Load, Vin=230VAC Io=Full Load Vin=230VAC Nil But, Output protected to short circuit conditions Io=Full Load to Half Load, Vin=100VAC Io=Full Load, Vin=230VAC Io=Full Load, Vin=100VAC Full Load, Vin=90VAC All output No load, Vin=240VAC Min. 90 47 0 77 Typ. 25 50 82 0.5 3 Nil Max. 264 63 25 0.4 0.25 50 100 85 1 5 4 8 2 0.5 -0.04 0.25 3 1 0.04 0.3 Unit VAC Hz W A A A A % % % % % mS mS S % %/°C W Conditions Parameter Test Conditions Operating Temperature Storage Temperature Relative Humidity No-Condensing Operating Temperature at 25°C, Calculated per MIL-HDBK-217F De-rate linearly from 100 % load at 40°C to 50 % load at 70°C Min. 0 -40 5 0.1M Typ. 40 Max. 70 85 95 Unit °C °C % Hrs Min. Unit 4242 50 B B VDC MΩ CLASS CLASS Approvals and Compliance Parameter Dielectric Withstanding Voltage for Primary to secondary Isolation Resistance EMI requirements for CISPR-22 EMI requirements for FCC PART-15 Test Conditions Primary to secondary Test Voltage= 500VDC Vin=220VAC Vin=110VAC Mechanical and PIN out Note: 1. Dimensions are shown in mm. 2. Weight: 200g approx. 3. Optional output connector.