HB52RF1289E2U-75B EO 1 GB Registered SDRAM DIMM 128-Mword × 72-bit, 133 MHz Memory Bus, 2-Bank Module (36 pcs of 64 M × 4 Components) PC133 SDRAM L E0019H10 (1st edition) (Previous ADE-203-1195A (Z)) Preliminary Jan. 30, 2000 Description Pr od The HB52RF1289E2U belongs to 8-byte DIMM (Dual In-line Memory Module) family, and has been developed as an optimized main memory solution for 8-byte processor applications. The HB52RF1289E2U is a 64M × 72 × 2-bank Synchronous Dynamic RAM Module, mounted 36 pieces of 256-Mbit SDRAM (HM5225405BTB) sealed in TCP package, 1 piece of PLL clock driver, 3 pieces register driver and 1 piece of serial EEPROM (2-kbit) for Presence Detect (PD). An outline of the HB52RF1289E2U is 168-pin socket type package (dual lead out). Therefore, the HB52RF1289E2U makes high density mounting possible without surface mount technology. The HB52RF1289E2U provides common data inputs and outputs. Decoupling capacitors are mounted beside TCP on the module board. Note: Do not push the cover or drop the modules in order to protect from mechanical defects, which would be electrical defects. Features t uc • Fully compatible with : JEDEC standard outline 8-byte DIMM • 168-pin socket type package (dual lead out) Outline: 133.35 mm (Length) × 30.48 mm (Height) × 4.80 mm (Thickness) Lead pitch: 1.27 mm • 3.3 V power supply • Clock frequency: 133 MHz (max) • LVTTL interface • Data bus width: × 72ECC • Single pulsed RAS • 4 Banks can operates simultaneously and independently • Burst read/write operation and burst read/single write operation capability Preliminary: The Specifications of this device are subject to change without notice. Please contact to your nearest Elpida Memory, Inc. regarding specifications. This product became EOL in September, 2002. Elpida Memory, Inc. is a joint venture DRAM company of NEC Corporation and Hitachi, Ltd. HB52RF1289E2U-75B EO • Programmable burst length: 1/2/4/8 • 2 variations of burst sequence Sequential Interleave • Programmable CE latency : 4 • Byte control by DQMB • Refresh cycles: 8192 refresh cycles/64 ms • 2 variations of refresh Auto refresh Self refresh L Ordering Information Type No. HB52RF1289E2U-75B CE latency Package 133 MHz 4 168-pin dual lead out socket type Gold Pr Pin Arrangement Frequency 1 pin 10 pin 11 pin 40 pin 41 pin Contact pad 84 pin od 85 pin 94 pin 95 pin 124 pin 125 pin 168 pin t uc Preliminary Data Sheet E0019H10 2 HB52RF1289E2U-75B Pin name Pin No. Pin name Pin No. Pin name Pin No. Pin name 1 VSS 43 VSS 85 VSS 127 VSS 2 DQ0 44 NC 86 DQ32 128 CKE0 3 DQ1 45 S2 87 DQ33 129 S3 4 DQ2 46 DQMB2 88 DQ34 130 DQMB6 5 DQ3 47 DQMB3 89 DQ35 131 DQMB7 6 VCC 48 NC 90 VCC 132 NC 7 DQ4 49 VCC 91 DQ36 133 VCC 8 DQ5 50 NC 92 DQ37 134 NC 9 DQ6 51 NC 93 DQ38 135 NC EO Pin No. L 10 52 CB2 94 DQ39 136 CB6 DQ8 53 CB3 95 DQ40 137 CB7 VSS 54 VSS 96 VSS 138 VSS DQ9 55 DQ16 97 DQ41 139 DQ48 14 DQ10 56 DQ17 98 DQ42 140 DQ49 15 DQ11 57 DQ18 99 DQ43 141 DQ50 16 DQ12 58 DQ19 100 DQ44 142 DQ51 17 DQ13 59 VCC 101 DQ45 143 VCC 18 VCC 60 DQ20 102 VCC 144 DQ52 19 DQ14 61 NC 103 DQ46 145 NC 20 DQ15 62 NC 104 DQ47 146 NC 21 CB0 63 NC 105 CB4 147 REGE 22 CB1 64 VSS 106 CB5 148 VSS 23 VSS 65 DQ21 107 VSS 149 DQ53 24 NC 66 DQ22 108 NC 150 DQ54 25 NC 67 DQ23 109 NC 151 DQ55 26 VCC 68 VSS 110 VCC 152 VSS 27 W 69 DQ24 111 CE 153 DQ56 28 DQMB0 70 DQ25 112 DQMB4 154 DQ57 29 DQMB1 71 DQ26 113 DQMB5 155 DQ58 30 S0 72 DQ27 114 S1 156 DQ59 31 NC 73 VCC 115 RE 157 VCC 32 VSS 74 DQ28 116 VSS 158 DQ60 33 A0 75 DQ29 117 A1 159 DQ61 34 A2 76 DQ30 118 A3 160 DQ62 35 A4 77 DQ31 119 A5 161 DQ63 11 12 13 t uc od Pr DQ7 Preliminary Data Sheet E0019H10 3 HB52RF1289E2U-75B Pin name Pin No. Pin name Pin No. Pin name Pin No. Pin name 36 A6 78 VSS 120 A7 162 VSS 37 A8 79 CK2 121 A9 163 CK3 38 A10 (AP) 80 NC 122 BA0 164 NC 39 BA1 81 WP 123 A11 165 SA0 40 VCC 82 SDA 124 VCC 166 SA1 41 VCC 83 SCL 125 CK1 167 SA2 42 CK0 84 VCC 126 A12 168 VCC EO Pin No. Pin name A0 to A12 L Pin Description DQ0 to DQ63 CB0 to CB7 S0 to S3 RE Address input Row address A0 to A12 Column address A0 to A9, A11 Pr BA0/BA1 Function Bank select address BA0/BA1 Data input/output Check bit (Data input/output) Chip select input Row enable (RAS) input CE od Column enable (CAS) input W Write enable input DQMB0 to DQMB7 Byte data mask CK0 to CK3 Clock input CKE0 Clock enable input WP Write protect for serial PD 1 Register enable SDA Data input/output for serial PD SCL Clock input for serial PD SA0 to SA2 Serial address input VCC Primary positive power supply VSS Ground NC No connection Note: 1. REGE is the Register Enable pin which permits the DIMM to operate in “buffered” mode and “registered” mode. To conform to this specification, mother boards must pull this pin to high state (“registerd” mode). Preliminary Data Sheet E0019H10 4 t uc REGE* HB52RF1289E2U-75B Serial PD Matrix*1 Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Hex value Comments 0 Number of bytes used by module manufacturer 1 0 0 0 0 0 0 0 80 128 1 Total SPD memory size 0 0 0 0 1 0 0 0 08 256 byte 2 Memory type 0 0 0 0 0 1 0 0 04 SDRAM 3 Number of row addresses bits 0 0 0 0 1 1 0 1 0D 13 4 Number of column addresses bits 0 0 0 0 1 0 1 1 0B 11 5 Number of banks 0 0 0 0 0 0 1 0 02 2 6 Module data width 0 1 0 0 1 0 0 0 48 72 bit 7 Module data width (continued) 0 0 0 0 0 0 0 0 00 0 (+) 8 Module interface signal levels 0 0 0 0 0 0 0 1 01 LVTTL 9 SDRAM cycle time (highest CE latency) 7.5 ns 0 1 1 1 0 1 0 1 75 CL = 3 10 SDRAM access from Clock (highest CE latency) 5.4 ns 0 1 0 1 0 1 0 0 54 *5 11 Module configuration type 0 0 0 0 0 0 1 0 02 ECC 12 Refresh rate/type 1 0 0 0 0 0 1 0 82 Normal (7.8125 µs) Self refresh 13 SDRAM width 0 0 0 0 0 1 0 0 04 64M × 4 14 Error checking SDRAM width 0 0 0 0 0 1 0 0 04 ×4 15 SDRAM device attributes: 0 minimum clock delay for back-toback random column addresses 0 0 0 0 0 0 1 01 16 SDRAM device attributes: Burst lengths supported 0 0 0 0 1 1 1 1 0F 1, 2, 4, 8 17 SDRAM device attributes: number of banks on SDRAM device 0 0 0 0 1 18 SDRAM device attributes: CE latency 0 0 0 0 0 1 19 SDRAM device attributes: S latency 0 0 0 0 0 0 EO Byte No. Function described L 0 0 0 04 4 1 0 06 2/3 0 1 01 0 t uc od Pr 1 CLK Preliminary Data Sheet E0019H10 5 HB52RF1289E2U-75B 20 SDRAM device attributes: W latency 0 0 0 0 0 0 0 1 01 0 21 SDRAM device attributes 0 0 0 1 0 1 1 0 16 Registered 22 SDRAM device attributes: General 0 0 0 0 1 1 1 0 0E VCC ± 10% 23 SDRAM cycle time (2nd highest CE latency) 10 ns 1 0 1 0 0 0 0 0 A0 CL = 2 *5 24 SDRAM access from Clock (2nd highest CE latency) 6 ns 0 1 1 0 0 0 0 0 60 *5 25 SDRAM cycle time (3rd highest CE latency) Undefined 0 0 0 0 0 0 0 0 00 26 SDRAM access from Clock (3rd 0 highest CE latency) Undefined 0 0 0 0 0 0 0 00 27 Minimum row precharge time 0 0 0 1 0 1 0 0 14 20 ns 28 Row active to row active min 0 0 0 0 1 1 1 1 0F 15 ns 29 RE to CE delay min 0 0 0 1 0 1 0 0 14 20 ns 30 Minimum RE pulse width 0 0 1 0 1 1 0 1 2D 45 ns 31 Density of each bank on module 1 0 0 0 0 0 0 0 80 2 bank 512M byte 32 Address and command signal input setup time 0 0 0 1 0 1 0 1 15 33 Address and command signal input hold time 0 0 0 0 1 0 0 0 08 0.8 ns*5 34 Data signal input setup time 0 0 0 1 0 1 0 1 15 1.5 ns*5 35 Data signal input hold time 0 0 0 0 1 0 0 0 08 0.8 ns*5 36 to 61 Superset information 0 0 0 0 0 0 0 0 00 Future use 62 SPD data revision code 0 od 1.5 ns*5 0 0 0 0 0 1 0 02 JEDEC2 63 Checksum for bytes 0 to 62 1 0 1 0 0 1 0 0 A4 164 64 Manufacturer’s JEDEC ID code 0 0 0 0 0 1 1 1 07 HITACHI 65 to 71 Manufacturer’s JEDEC ID code 0 0 0 0 0 0 0 0 00 72 × × × × × × × × ×× L Pr Manufacturing location Preliminary Data Sheet E0019H10 6 t uc Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Hex value Comments EO Byte No. Function described * 2 (ASCII8bit code) HB52RF1289E2U-75B Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Hex value Comments 73 Manufacturer’s part number 0 1 0 0 1 0 0 0 48 H 74 Manufacturer’s part number 0 1 0 0 0 0 1 0 42 B 75 Manufacturer’s part number 0 0 1 1 0 1 0 1 35 5 76 Manufacturer’s part number 0 0 1 1 0 0 1 0 32 2 77 Manufacturer’s part number 0 1 0 1 0 0 1 0 52 R 78 Manufacturer’s part number 0 1 0 0 0 1 1 0 46 F 79 Manufacturer’s part number 0 0 1 1 0 0 0 1 31 1 80 Manufacturer’s part 0 0 1 1 0 0 1 0 32 2 81 Manufacturer’s part number 0 0 1 1 1 0 0 0 38 8 82 Manufacturer’s part number 0 0 1 1 1 0 0 1 39 9 83 Manufacturer’s part number 0 1 0 0 0 1 0 1 45 E 84 Manufacturer’s part number 0 0 1 1 0 0 1 0 32 2 85 Manufacturer’s part number 0 1 0 1 0 1 0 1 55 U 86 Manufacturer’s part number 0 0 1 0 1 1 0 1 2D — 87 Manufacturer’s part number 0 0 1 1 0 1 1 1 37 7 88 Manufacturer’s part number 0 0 1 1 0 1 0 1 35 5 89 Manufacturer’s part number 0 1 0 0 0 0 1 0 42 B 90 Manufacturer’s part number 0 0 1 0 0 0 0 0 20 (Space) 91 Revision code 0 0 1 1 0 0 0 0 30 Initial 92 Revision code 0 0 1 0 0 0 0 0 20 (Space) 93 Manufacturing date × × × × × × × × ×× Year code (BCD) 94 Manufacturing date × × × × × × × × ×× Week code (BCD) *4 EO Byte No. Function described L od Pr *3 99 to 125 Manufacturer specific data — — — — — — — — — 126 Reserved (Intel specification frequency) 0 1 1 0 0 1 0 0 64 127 Reserved (Intel specification CE# latency support) 1 0 0 0 0 1 t uc 95 to 98 Assembly serial number 1 1 87 Notes: 1. All serial PD data are not protected. 0: Serial data, “driven Low”, 1: Serial data, “driven High”. 2. Byte72 is manufacturing location code. (ex: In case of Japan, byte72 is 4AH. 4AH shows “J” on ASCII code.) 3. Bytes 95 through 98 are assembly serial number. 4. All bits of 99 through 125 are not defined (“1” or “0”). 5. These specifications are defined based on component specifiation, not module. Preliminary Data Sheet E0019H10 7 HB52RF1289E2U-75B Block Diagram EO RS0 RS1 RDQMB0 4 DQ0 to DQ3 4 DQ4 to DQ7 RDQMB4 DQMB CS 10 Ω I/O0 to I/O3 D0 DQMB CS 10 Ω I/O0 to I/O3 D1 DQMB CS I/O0 to I/O3 I/O0 to I/O3 D2 L 10 Ω DQMB CS 10 Ω DQ12 to DQ15 I/O0 to I/O3 D3 DQMB CS CB0 to CB3 4 10 Ω 10 Ω 4 10 Ω 4 10 Ω 4 10 Ω I/O0 to I/O3 D4 DQ36 to DQ39 4 10 Ω DQ16 to DQ19 I/O0 to I/O3 D5 DQMB CS DQMB CS D10 I/O0 to I/O3 DQMB CS DQMB CS D20 I/O0 to I/O3 DQ40 to DQ43 D28 D21 I/O0 to I/O3 DQ44 to DQ47 I/O0 to I/O3 I/O0 to I/O3 D22 CB4 to CB7 I/O0 to I/O3 D29 DQMB CS D12 I/O0 to I/O3 DQMB CS DQMB CS I/O0 to I/O3 I/O0 to I/O3 DQMB CS D11 DQMB CS DQMB CS 4 10 Ω I/O0 to I/O3 D6 DQMB CS I/O0 to I/O3 D23 D30 DQMB CS D13 I/O0 to I/O3 D31 I/O0 to I/O3 10 Ω 4 10 Ω DQ48 to DQ51 D24 DQ52 to DQ55 DQMB CS DQMB CS 4 DQMB CS I/O0 to I/O3 D14 I/O0 to I/O3 I/O0 to I/O3 D32 DQMB CS DQMB CS D15 I/O0 to I/O3 od RDQMB3 D33 RDQMB7 DQMB CS 4 10 Ω DQ24 to DQ27 I/O0 to I/O3 D7 DQMB CS 4 10 Ω DQ28 to DQ31 I/O0 to I/O3 D8 DQMB CS I/O0 to I/O3 DQMB CS D25 4 10 Ω 4 10 Ω DQ56 to DQ59 I/O0 to I/O3 D26 DQ60 to DQ63 10k RS0, RS1, RS2, RS3 RDQMB0 to RDQMB7 RBA0 to RBA1 -> BA0 to BA1: SDRAMs D0 to D35 CK1 RA0 to RA12 -> A0 to A12: SDRAMs D0 to D35 to CK3 RRAS -> RAS: SDRAMs D0 to D35 RCAS -> CAS: SDRAMs D0 to D35 VCC RCKE0 -> CKE: SDRAMs D0 to D35 0.0022 µF × 25 pcs RW -> WE: SDRAMs D0 to D35 VSS Serial PD SCL SCL SDA U0 A0 A1 SDA WP A2 47 kΩ SA0 SA1 SA2 VSS Notes: 1. The SDA pull-up resistor is required due to the open-drain/open-collector output. 2. The SCL pull-up resistor is recommended because of the normal SCL line inacitve "high" state. Preliminary Data Sheet E0019H10 D17 I/O0 to I/O3 10 Ω DQMB CS I/O0 to I/O3 D34 DQMB CS I/O0 to I/O3 D35 PLL 12 pF CK : SDRAMs (D0 to D35) Register t uc R E G I S T E R I/O0 to I/O3 D16 DQMB CS DQMB CS CK0 S0, S1, S2, S3 DQMB0 to DQMB7 BA0 to BA1 A0 to A12 RE CE CKE0 W 8 I/O0 to I/O3 D27 RDQMB6 DQMB CS VCC REGE PLL CK I/O0 to I/O3 DQMB CS D19 Pr RS2 RS3 RDQMB2 DQ20 to DQ23 4 I/O0 to I/O3 D9 RDQMB5 DQMB CS DQ8 to DQ11 4 10 Ω DQMB CS RDQMB1 4 4 DQ32 to DQ35 I/O0 to I/O3 DQMB CS DQMB CS D18 10 Ω VSS 12 pF VCC (D0 to D35, U0) 0.22 µF × 19 pcs VSS (D0 to D35, U0) * D0 to D35: HM5225405 PLL: 2510 Register: 162834 U0: 2-k bit EEPROM HB52RF1289E2U-75B Absolute Maximum Ratings Symbol Value Unit Note Voltage on any pin relative to V SS VT –0.5 to VCC + 0.5 (≤ 4.6 (max)) V 1 Supply voltage relative to VSS VCC –0.5 to +4.6 V 1 Short circuit output current Iout 50 mA Power dissipation PT 18.0 W Operating temperature Topr 0 to +55 °C Storage temperature Tstg –50 to +100 °C EO Parameter Note: 1. Respect to V SS L DC Operating Conditions (Ta = 0 to +55°C) Symbol Min Max Unit Notes Supply voltage VCC 3.0 3.6 V 1 VSS 0 0 V 3 VIH 2.0 VCC V 1, 4 VIL 0 0.8 V 1, 5 — — 100 lx Input high voltage Input low voltage Ambient illuminance All voltage referred to VSS The supply voltage with all V CC and V CCQ pins must be on the same level. The supply voltage with all VSS and VSS Q pins must be on the same level. VIH (max) = VCC + 2.0 V for pulse width ≤ 3 ns at VCC. VIL (min) = VSS – 2.0 V for pulse width ≤ 3 ns at VSS . t uc od Notes: 1. 2. 3. 4. 5. Pr Parameter Preliminary Data Sheet E0019H10 9 HB52RF1289E2U-75B VIL/VIH Clamp (Component characteristics) EO This SDRAM component has VIL and V IH clamp for CK, CKE, S, DQMB and DQ pins. Minimum VIL Clamp Current VIL (V) I (mA) –2 –32 –1.8 –25 –1.6 –19 –1.4 –13 –1 –0.9 L –1.2 –8 –4 –2 –0.6 –0.6 0 –0.4 Pr –0.8 0 –0.2 0 0 0 I (mA) –10 –15 –20 –25 –30 –1 VIL (V) Preliminary Data Sheet E0019H10 10 –0.5 0 t uc –35 –1.5 od 0 –2 –5 HB52RF1289E2U-75B Minimum VIH Clamp Current (referred to VIH) I (mA) VCC + 2 10 VCC + 1.8 8 VCC + 1.6 5.5 VCC + 1.4 3.5 VCC + 1.2 1.5 VCC + 1 0.3 VCC + 0.8 0 VCC + 0.6 0 EO VIH (V) VCC + 0 8 6 4 0 VCC + 0 0 0 VCC + 0.5 od 2 0 Pr 10 I (mA) VCC + 0.2 L VCC + 0.4 VCC + 1 VCC + 1.5 VCC + 2 VIH (V) t uc Preliminary Data Sheet E0019H10 11 HB52RF1289E2U-75B IOL/IOH Characteristics (Component characteristics) EO Output Low Current (IOL) I OL I OL Vout (V) Min (mA) Max (mA) 0 0 0 0.4 27 71 0.65 41 108 0.85 51 134 58 L 151 70 188 72 194 75 203 77 209 1 1.4 1.5 1.65 1.8 Pr 1.95 3 3.45 250 77 212 80 220 81 223 IOL (mA) 150 100 50 0 0 0.5 1 1.5 2 Vout (V) Preliminary Data Sheet E0019H10 12 2.5 min max t uc od 200 3 3.5 HB52RF1289E2U-75B Output High Current (I OH ) (Ta = 0 to 55˚C, V CC = 3.0 V to 3.45 V, VSS = 0 V) I OH Vout (V) Min (mA) Max (mA) 3.45 — –3 3.3 — –28 3 0 –75 2.6 –21 –130 2.4 –34 –154 2 –59 –197 1.8 –67 –227 –73 –248 –78 –270 –81 –285 1 –89 –345 0 –93 –503 EO I OH L 1.65 1.5 1.4 –200 –300 –400 0.5 1 1.5 2 2.5 3 3.5 –500 –600 Vout (V) min max t uc od IOH (mA) –100 0 Pr 0 Preliminary Data Sheet E0019H10 13 HB52RF1289E2U-75B DC Characteristics (Ta = 0 to 55°C, VCC = 3.3 V ± 0.3 V, VSS = 0 V) EO Parameter HB52RF1289E2U-75B Symbol Min Max Unit Test conditions Notes — 3215 mA Burst length = 1 t RC = min 1, 2, 3 I CC1 Standby current in power I CC2P down — 803 mA CKE = VIL, t CK = 12 ns 6 Standby current in power I CC2PS down (input signal stable) — 767 mA CKE = VIL, t CK = ∞ 7 Standby current in non power down I CC2N — 1415 mA CKE, S = VIH, t CK = 12 ns 4 Active standby current in power down I CC3P — 839 mA CKE = VIL, t CK = 12 ns 1, 2, 6 Active standby current in non power down I CC3N — 1775 mA CKE, S = VIH, t CK = 12 ns 1, 2, 4 t CK = min, BL = 4 1, 2, 5 t RC = min 3 8 Operating current L Burst operating current Pr — 3575 mA I CC5 — 5195 mA Self refresh current I CC6 — 803 mA VIH ≥ VCC – 0.2 V VIL ≤ 0.2 V Input leakage current I LI –10 10 µA 0 ≤ Vin ≤ VCC Output leakage current I LO –10 10 µA 0 ≤ Vout ≤ VCC DQ = disable Output high voltage VOH 2.4 — V I OH = –4 mA Output low voltage VOL — 0.4 V I OL = 4 mA Refresh current od I CC4 t uc Notes: 1. I CC depends on output load condition when the device is selected. ICC (max) is specified at the output open condition. 2. One bank operation. 3. Input signals are changed once per one clock. 4. Input signals are changed once per two clocks. 5. Input signals are changed once per four clocks. 6. After power down mode, CK operating current. 7. After power down mode, no CK operating current. 8. After self refresh mode set, self refresh current. Preliminary Data Sheet E0019H10 14 HB52RF1289E2U-75B Capacitance (Ta = 25°C, VCC = 3.3 V ± 0.3 V) Symbol Max Unit Notes Input capacitance (Address) CI1 25 pF 1, 2, 4 Input capacitance (RE, CE, W) CI2 25 pF 1, 2, 4 Input capacitance (CKE) CI3 45 pF 1, 2, 4 Input capacitance (S) CI4 20 pF 1, 2, 4 Input capacitance (CK) CI5 45 pF 1, 2, 4 Input capacitance (DQMB) CI6 20 pF 1, 2, 4 Input/Output capacitance (DQ) CI/O1 25 pF 1, 2, 3, 4 EO Parameter Capacitance measured with Boonton Meter or effective capacitance measuring method. Measurement condition: f = 1 MHz, 1.4 V bias, 200 mV swing. DQMB = VIH to disable Data-out. This parameter is sampled and not 100% tested. L Notes: 1. 2. 3. 4. Pr AC Characteristics (Ta = 0 to 55°C, VCC = 3.3 V ± 0.3 V, VSS = 0 V) HB52RF1289E2U-75B Parameter System clock cycle time CK high pulse width Symbol PC100 Symbol Min Max Unit Notes t CK Tclk 7.5 — ns 1 t CKH Tch 3.4 — ns 1 Tcl 3.4 — ns 1 Access time from CK t AC Tac — 6.3 ns 1, 2 Data-out hold time t OH Toh 1.8 — ns 1, 2 CK to Data-out low impedance t LZ 1.1 — ns 1, 2, 3 CK to Data-out high impedance t HZ — 6.3 ns 1, 4 Data-in setup time t DS Tsi 2.4 — ns 1 Data in hold time t DH Thi 1.7 — ns 1 Address setup time t AS Tsi 1.9 — ns 1 Address hold time t AH Thi 1.5 — ns 1, 5 CKE setup time t CES Tsi 1.9 — ns 1, 5 CKE setup time for power down exit t CESP Tpde 1.9 — ns 1 t uc t CKL od CK low pulse width Preliminary Data Sheet E0019H10 15 HB52RF1289E2U-75B AC Characteristics (Ta = 0 to 55°C, VCC = 3.3 V ± 0.3 V, VSS = 0 V) (cont) EO HB52RF1289E2U-75B Parameter Symbol PC100 Symbol Min Max Unit Notes CKE hold time t CEH Thi 1.5 — ns 1 Command setup time t CS Tsi 1.9 — ns 1 Command hold time t CH Thi 1.5 — ns 1 Ref/Active to Ref/Active command period t RC Trc 67.5 — ns 1 Tras 45 120000 ns 1 Active command to column command t RCD (same bank) Trcd 22.5 — ns 1 Precharge to active command period t RP Trp 22.5 — ns 1 Write recovery or data-in to precharge t DPL lead time Tdpl 15 — ns 1 Active (a) to Active (b) command period t RRD Trrd 15 — ns 1 Transition time (rise to fall) tT 1 5 ns t REF — 64 ms Active to precharge command period t RAS L AC measurement assumes t T = 1 ns. Reference level for timing of input signals is 1.5 V. Access time is measured at 1.5 V. Load condition is C L = 50 pF. t LZ (max) defines the time at which the outputs achieves the low impedance state. t HZ (max) defines the time at which the outputs achieves the high impedance state. t CES defines CKE setup time to CK rising edge except power down exit command. Test Conditions • Input and output timing reference levels: 1.5 V • Input waveform and output load: See following figures • Ambient illuminance: Under 100 lx 2.4 V input 0.4 V DQ 2.0 V 0.8 V CL t T tT Preliminary Data Sheet E0019H10 16 t uc od Notes: 1. 2. 3. 4. 5. Pr Refresh period HB52RF1289E2U-75B Relationship Between Frequency and Minimum Latency HB52RF1289E2U-75B Frequency (MHz) 133 EO Parameter PC100 Symbol Symbol 7.5 Notes Active command to column command (same bank) I RCD 3 1 Active command to active command (same bank) I RC 9 = [IRAS + IRP] 1 Active command to precharge command (same bank) I RAS 6 1 Precharge command to active command (same bank) I RP 3 1 2 1 2 1 L tCK (ns) I DPL Tdpl Active command to active command (different bank) I RRD Self refresh exit time I SREX Tsrx 2 2 Last data in to active command (Auto precharge, same bank) I APW Tdal 5 = [IDPL + IRP] Self refresh exit to command input I SEC 9 = [IRC] 3 Precharge command to high impedance I HZP Last data out to active command (Auto precharge, same bank) I APR 0 Last data out to precharge (early precharge) I EP –3 Pr Write recovery or data-in to precharge command (same bank) Write command to data in latency DQMB to data in DQMB to data out CKE to CK disable Register set to active command I CCD Tccd 1 I WCD Tdwd 1 I DID Tdqm 1 I DOD Tdqz 3 I CLE Tcke 2 I RSA Tmrd 3 I CDD Power down exit to command input I PEC t uc S to command disable 4 od Column command to column command Troh 0 1 Preliminary Data Sheet E0019H10 17 HB52RF1289E2U-75B Pin Functions EO CK0 to CK3 (input pin): CK is the master clock input to this pin. The other input signals are referred at CK rising edge. S0 to S3 (input pin): When S is Low, the command input cycle becomes valid. When S is High, all inputs are ignored. However, internal operations (bank active, burst operations, etc.) are held. RE, CE and W (input pins): Although these pin names are the same as those of conventional DRAMs, they function in a different way. These pins define operation commands (read, write, etc.) depending on the combination of their voltage levels. For details, refer to the command operation section. L A0 to A12 (input pins): Row address (AX0 to AX12) is determined by A0 to A12 level at the bank active command cycle CK rising edge. Column address (AY0 to AY9, AY11) is determined by A0 to A9, A11 level at the read or write command cycle CK rising edge. And this column address becomes burst access start address. A10 defines the precharge mode. When A10 = High at the precharge command cycle, all banks are precharged. But when A10 = Low at the precharge command cycle, only the bank that is selected by BA0/BA1 (BA) is precharged. Pr BA0/BA1 (input pin): BA0/BA1 are bank select signal (BA). The memory array is divided into bank 0, bank 1, bank 2 and bank 3. If BA0 is Low and BA1 is Low, bank 0 is selected. If BA0 is High and BA1 is Low, bank 1 is selected. If BA0 is Low and BA1 is High, bank 2 is selected. If BA0 is High and BA1 is High, bank 3 is selected. od CKE0 (input pin): This pin determines whether or not the next CK is valid. If CKE is High, the next CK rising edge is valid. If CKE is Low, the next CK rising edge is invalid. This pin is used for power-down and clock suspend modes. DQMB0 to DQMB7 (input pins): Read operation: If DQMB is High, the output buffer becomes High-Z. If the DQMB is Low, the output buffer becomes Low-Z. Write operation: If DQMB is High, the previous data is held (the new data is not written). If DQMB is Low, the data is written. DQ0 to DQ63, CB0 to CB7 (input/output pins): Data is input to and output from these pins. VSS (power supply pins): Ground is connected. t uc VCC (power supply pins): 3.3 V is applied. REGE (input pins): If REGE is High, the register is ″registered″ mode. If REGE is Low, the register is ″buffered″ mode. Detailed Operation Part Refer to the HM5225165B/HM5225805B/HM5225405B-75/A6/B6 datasheet. Preliminary Data Sheet E0019H10 18 HB52RF1289E2U-75B Physical Outline EO Unit: mm inch Front side 133.35 5.25 (DATUM -A-) 4.80 max 0.189 max 4.00 min 0.157 min (63.67) (2.51) L Component area (Front) 1 84 B C 85 127.35 5.014 Component area (Back) od (DATUM -A-) 3.125 ± 0.125 6.35 0.250 2.00 ± 0.10 0.079 ± 0.004 1.00 0.039 0.123 ± 0.005 0.123 ± 0.005 0.20 ± 0.15 0.010 ± 0.0004 Detail C (DATUM -A-) R FULL 6.35 0.250 4.175 0.164 2.00 ± 0.10 0.079 ± 0.004 t uc 1.00 ± 0.05 0.039 ± 0.002 1.27 0.050 Detail B R FULL 3.125 ± 0.125 Detail A 2.50 ± 0.20 0.098 ± 0.008 4.00 0.157 2 – φ 3.00 2 – φ 0.118 Pr Back side 1.27 0.050 54.61 2.150 17.80 0.70 0.450 A 36.83 1.450 168 11.43 30.48 1.20 3.00 0.118 3.00 0.118 Note: Tolerance on all dimensions ± 0.15/0.006 unless otherwise specified. ED480120W Preliminary Data Sheet E0019H10 19 HB52RF1289E2U-75B Cautions EO L 1. Elpida Memory, Inc. neither warrants nor grants licenses of any rights of Elpida Memory, Inc.’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Elpida Memory, Inc. bears no responsibility for problems that may arise with third party’s rights, including intellectual property rights, in connection with use of the information contained in this document. 2. Products and product specifications may be subject to change without notice. Confirm that you have received the latest product standards or specifications before final design, purchase or use. 3. Elpida Memory, Inc. makes every attempt to ensure that its products are of high quality and reliability. However, contact Elpida Memory, Inc. before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment or medical equipment for life support. 4. Design your application so that the product is used within the ranges guaranteed by Elpida Memory, Inc. particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and other characteristics. Elpida Memory, Inc. bears no responsibility for failure or damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as fail-safes, so that the equipment incorporating Elpida Memory, Inc. product does not cause bodily injury, fire or other consequential damage due to operation of the Elpida Memory, Inc. product. 5. This product is not designed to be radiation resistant. 6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without written approval from Elpida Memory, Inc.. 7. Contact Elpida Memory, Inc. for any questions regarding this document or Elpida Memory, Inc. semiconductor products. t uc od Pr Preliminary Data Sheet E0019H10 20