IPC PSU FSP300-60UAP DESCRIPTION FSP300-60UAP is an industrial level of switching power supply. The power supply comes to offer the total power capacity up to 300 Watts, and uses unique active PFC (Power Factor C orrection) circuit design with its high-load electrical components, makes it to be perfectly used in an industrial environment. In addition, with its full range of input and output electrical features, the power supply is ideally the best choice for server, workstation, communication or any other automation applications to use. The product also complies with the latest safety and EMC standards, which is perfectly to meet various regulations worldwide. SAFETY STANDARD APPAOVAL APPLICATION OUTPUT SPECIFICATION For standard, advanced server, NAS, storage, and industrial power system. Hold up Time: FEATURES 80 Plus Platinum Low Ripple & Noise Output over voltage protection Short circuit protection on all outputs Resettable power shut down INTERNAL 4 cm fan Two +12V output (+12V/1,+12V/2) 100% burn-in under high ambient temperature(50℃) Vacuum-impregnated transformer MTBF:100K hours at 25℃ 100% Hi-pot tested Line input fuse protection Ouput Voltage Regulation: Output Rise Time: Ripple & Noise: W ATTAGE Wattage: 300W DIMENSION Dimension: 190mm(L) x 100mm(W) x 40.5mm(H) PRODUCT HIGHLIGHT Efficiency Level: Altitude: ENVIRONMENTAL SPECIFICATION TEMP.Range: MTBF: 80 Plus Platinum 5000M INPUT SPECIFICATION Input Range: Input Frequency: Input Current: 115V/60Hz 12mSec. Minimum@100% Load, 230V/50Hz 16mSec. Minimum,@100% Load +3.3Vdc output : +3.5 Vdc minimum, + 4.8Vdc maximum +5Vdc output : +5.5 Vdc minimum, + 7Vdc maximum +12Vdc output : +13.4 Vdc minimum, + 16Vdc maximum 115V-rms/230V-rms 5V 20ms Maximum 3.3V:50mV p-p 5V:50mV p-p 12V1:120mV p-p 12V2:120mV p-p -12V:120mV p-p 5Vsb:50mV p-p 90-264 Vac 47-63 Hz 115V@ 5.0 Amps-rms maximum 230V@ 2.5 Amps-rms maximum Storage Temperature: 20°C to + 80℃ The power supply have a minimum predicted MTBF(MIL-HDBK-217) of 100,000 hours of continuous operation at 25℃, maximum-output load, and nominal AC inout voltage GENERAL SPECIFICATION Effciency: Voltage Regulation: 92% 230VAC +3.3V, +12V, +5V, +5VSB: ±5% -12V, -5V: ±10% *Output Voltage and C urrent Rating +3.3V Ripple-Noise(R-P) mV 50mV Regulation Load % ±5% Output Max.(A) 14A Output Min.(A) 0.3A +5V 50mV ±5% 16A 0.3A +12V1 120mV ±5% 16A 0.5A +12V2 120mV ±5% 16A 0.5A -12V 120mV ±10% 0.5A 0A +5Vsb 50mV ±5% 3A 0A NOTES C ombined 3.3V and 5 power shall not exceed 100W. Ripple and noise measurements shall be made under all specified load conditions through a single pole low pass filter with 20MHz cutoff frequency Outputs shall bypassed at the connector with a 0.1uF ceramic disk capacitor and a 47uF electrolytic capacitor to simulate system loading. Maximum continuous total DC output power should not exceed 300W This content is subject to change, please refer to specification for m ore detail. FSP reserve the right to change the content without prior notice