LM95245 Precision Remote Diode Digital Temperature Sensor with TruTherm™ BJT Beta Compensation Technology for 45nm Process General Description The LM95245 is an 11-bit digital temperature sensor with a 2-wire System Management Bus (SMBus) interface and TruTherm technology that can monitor the temperature of a remote diode as well as its own temperature. The LM95245 can be used to very accurately monitor the temperature of external devices such as microprocessors. TruTherm technology allows the LM95245 to precisely monitor thermal diodes found in 90 nm and smaller geometry processes. The LM95245 is specifically targeted for Intel processors on 45nm process. LM95245 reports temperature in two different formats for +127.875°C/-128°C range and 0°C/255°C range. The LM95245 T_CRIT and OS outputs are asserted when either unmasked channel exceeds its programmed limit and can be used to shutdown the system, to turn on the system fans, or as a microcontroller interrupt function. The current status of the T_CRIT and OS pins can be read back from the status registers via the SMBus interface. All limits have a shared programmable hysteresis register. The remote temperature channel of the LM95245 has a programmable digital filter. The LM95245 is targeted for a typical Intel® processor on a 45 nm, 65 nm or 90nm process, and has an offset register for maximum flexibility and best accuracy. The LM95245 has a three-level address pin to connect up to 3 devices to the same SMBus master, that is shared with the OS output. The LM95245 has a programmable conversion rate register and a standby mode to save power. One conversion can be triggered in standby mode by writing to the one-shot register. ■ ■ ■ ■ ■ ■ ■ Digital filter for remote channel Programmable TCRIT and OS thresholds Programmable shared hysteresis register Diode Fault Detection Mask, Offset, and Status Registers SMBus 2.0 compatible interface, supports TIMEOUT Programmable conversion rate for best power consumption Three-level address pin Standby mode one-shot conversion control Pin-for-pin compatible with the LM95235 and LM86/LM89/ LM99 8-pin MSOP package ■ ■ ■ ■ Key Specifications ■ Supply Voltage ■ Supply Current, Conv. Rate = 1 Hz ■ Remote Diode Temperature Accuracy 3.0 V to 3.6 V TA = 25°C to 85°C; TD = 50°C to 105°C ±0.75°C (max) TA = 25°C to 85°C; TD = 40°C to 125°C ±1.5°C (max) 350 µA (typ) ■ Local Temperature Accuracy TA = 25°C to 100°C ■ Conversion Rate, Both Channels ±2.0°C (max) 16 to 0.4 Hz Applications ■ Processor/Computer System Thermal Management Features (e.g. Laptops, Desktops, Workstations, Servers) ■ Remote and Local temperature channels ■ Targeted for Intel 45nm processor diodes ■ Two Formats: −128°C to +127.875°C and ■ Electronic Test Equipment ■ Office Electronics 0°C to 255.875°C Connection Diagram MSOP-8 30015102 TOP VIEW TruTherm™ is a trademark of National Semiconductor Corporation. Intel® is a registered trademark of Intel Corporation. Pentium® is a registered trademark of Intel Corporation. © 2007 National Semiconductor Corporation 300151 www.national.com LM95245 Precision Remote Diode Digital Temperature Sensor with TruTherm BJT Beta Compensation Technology for 45nm Process October 2007 LM95245 Ordering Information Order Number Package Marking NS Package Number Transport Media SMBus Device Address LM95245CIMM T45C MUA08A (MSOP-8) 1000 Units on Tape and Reel 18h, 29h, 4Ch LM95245CIMM-1 T46C MUA08A (MSOP-8) 1000 Units on Tape and Reel 19h, 29h, 4Dh LM95245CIMMX T45C MUA08A (MSOP-8) 3500 Units on Tape and Reel 18h, 29h, 4Ch LM95245CIMMX-1 T46C MUA08A (MSOP-8) 3500 Units on Tape and Reel 19h, 29h, 4Dh Simplified Block Diagram 30015101 www.national.com 2 LM95245 Pin Descriptions Pin Number Name Type Function and Connection 1 VDD Power Device power supply. Requires bypass capacitor of 10 µF in parallel with 0.1 µF and 100 pF. Place 100 pF closest to device pin. 2 D+ Analog Input/Output Positive input from the thermal diode. 3 D- Analog Input/Output Negative input from the thermal diode. 4 T_CRIT Digital Output 5 GND Ground Critical temperature output. Open-drain output requires pull-up resistor. Active “LOW”. Device ground. 6 OS/A0 Digital Input/Output Over-temperature shutdown comparator output or SMBus slave address input. Defaults as an SMBus slave address input that selects one of three addresses. Can be tied to VDD, GND, or to the middle of a resistor divider connected between VDD and GND. When programmed as an OS comparator output it is active “Low” and open drain. 7 SMBDAT Digital Input/Output SMBus interface data pin. Open-drain output requires pull-up resistor. 8 SMBCLK Digital Input SMBus interface clock pin. Typical Application 30015103 3 www.national.com LM95245 Absolute Maximum Ratings (Note 1) Operating Ratings Supply Voltage, VDD Voltage at SMBDAT, SMBCLK, (Note 1) −0.3V to 6.0V −0.5V to 6.0V T_CRIT, OS/A0 Pins Voltage at Other Pins Input Current at D− Pin (Note 4) Input Current at All Other Pins (Note 4) Output Sink Current SMBDAT, T_Crit, OS Pins Package Input Current (Note 4) ESD Susceptibility (Note 3) Human Body Model Machine Model Charged Device Model Operating Temperature Range Electrical Characteristics Temperature Range LM95245CIMM (VDD +0.3V) ±1 mA -40°C to +125°C TMIN ≤ TA ≤ TMAX -40°C ≤ TA ≤ +85°C Supply Voltage (VDD) ±5 mA +3.0V to +3.6V Soldering process must comply with National Semiconductor's Reflow Temperature Profile specifications. Refer to www.national.com/packaging. (Note 5) 10 mA 30 mA 2500V 250V 1000V +125°C −65°C to +150°C Junction Temperature (Note 2) Storage Temperature Temperature-to-Digital Converter Characteristics Unless otherwise noted, these specifications apply for VDD = +3.0 Vdc to 3.6 Vdc. Boldface limits apply for TA = TJ = TMIN ≤ TA ≤ TMAX; all other limits TA = TJ = +25°C, unless otherwise noted. TJ is the junction temperature of the LM95245. TD is the junction temperature of the remote thermal diode. Parameter Conditions Typical (Note 6) LM95245 CIMM Limits (Note 7) Units ±1 ±2 °C (max) ±6 °C (max) Temperature Accuracy Using Local Diode (Note 8) TA = 25°C to +100°C Temperature Accuracy Using Remote Diode (Note 9) TA = +25°C to +85°C; TD = +50°C to +105°C 45nm Intel Processor ±0.5 ±0.75 °C (max) TA = +25°C to +85°C; TD = +40°C to +120°C 45nm Intel Processor ±0.75 ±1.5 °C (max) TA = -40°C to +25°C; TD = +25°C to +125°C 45nm Intel Processor ±3.0 °C (max) Remote Diode Measurement Resolution TA = -40°C to +25°C Digital Filter Off Digital Filter On Local Diode Measurement Resolution °C 13 Bits 0.03125 °C 11 Bits 63 °C 72 33 ms (max) ms SMBus Inactive, 1 Hz conversion rate (Note 11) 350 Standby Mode 300 µA 400 mV D− Source Voltage External Diode Current Source Bits 0.125 Conversion Time, Fastest Setting Local and Remote Channels (Note 10) Local or Remote Channels Quiescent Current 11 0.125 High-level 172 Low-level 10.75 Diode Source Current Ratio 670 225 µA (max) µA (max) µA 16 Power-On Reset Voltage 2.8 V (max) 1.6 V (min) T_CRIT Pin Temperature Threshold Default +110 °C OS Pin Temperature Threshold Default +85 °C www.national.com 4 LM95245 Logic Electrical Characteristics Digital DC Characteristics Unless otherwise noted, these specifications apply for VDD= +3.0 Vdc to 3.6 Vdc. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA= TJ= +25°C, unless otherwise noted. Symbol Parameter Conditions Typical (Note 6) Limits (Note 7) Units (Limit) SMBDAT, SMBCLK INPUTS VIN(1) Logical “1” Input Voltage 2.1 V (min) VIN(0) Logical “0” Input Voltage 0.8 V (max) VIN(HYST) SMBDAT and SMBCLK Digital Input Hysteresis IIN(1) Logical “1” Input Current VIN = VDD −0.005 −10 µA (max) IIN(0) Logical “0” Input Current VIN = 0 V 0.005 +10 µA (max) CIN Input Capacitance 400 mV 5 pF A0 DIGITAL INPUT VIH Input High Voltage VIM Input Middle Voltage VIL Input Low Voltage IIN(1) Logical “1” Input Current VIN = VDD IIN(0) Logical “0” Input Current VIN = 0 V CIN Input Capacitance 0.90 × VDD V (min) 0.57 × VDD V (max) 0.43 × VDD V (min) 0.10 × VDD V (max) −0.005 −10 µA (max) 0.005 +10 µA (max) 5 pF SMBDAT, T_CRIT, OS DIGITAL OUTPUTS IOH High Level Output Leakage Current VOUT = VDD 10 µA (max) VOL(T_CRIT, OS) T_CRIT, OS Low Level Output Voltage IOL = 6 mA 0.4 V (max) VOL(SMBDAT) SMBDAT Low Level Output Voltage IOL = 4 mA IOL = 6 mA 0.4 0.6 V (max) V (max) COUT Digital Output Capacitance 5 5 pF www.national.com LM95245 SMBus Digital Switching Characteristics Unless otherwise noted, these specifications apply for VDD= +3.0 Vdc to +3.6 Vdc, CL (load capacitance) on output lines = 80 pF. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = +25°C, unless otherwise noted. The switching characteristics of the LM95245 fully meet or exceed the published specifications of the SMBus version 2.0. The following parameters are the timing relationships between SMBCLK and SMBDAT signals related to the LM95245. They adhere to, but are not necessarily, the SMBus specifications. Symbol Parameter Conditions Typical Limits (Note 6) (Note 7) Units (Limit) 100 10 kHz (max) kHz (min) 4.7 25 µs (min) ms (max) fSMB SMBus Clock Frequency tLOW SMBus Clock Low Time from VIN(0)max to VIN(0)max tHIGH SMBus Clock High Time from VIN(1)min to VIN(1)min tR,SMB SMBus Rise Time (Note 12) 1 µs (max) tF,SMB SMBus Fall Time (Note 13) 0.3 µs (max) tOF Output Fall Time CL = 400 pF, IO = 3 mA, (Note 13) tTIMEOUT tSU;DAT 4.0 µs (min) 250 ns (max) SMBDAT and SMBCLK Time Low for Reset of Serial Interface (Note 14) 25 35 ms (min) ms (max) Data In Setup Time to SMBCLK High 250 ns (min) tHD;DAT Data Out Stable after SMBCLK Low 300 1075 ns (min) ns (max) tHD;STA Start Condition SMBDAT Low to SMBCLK Low (Start condition hold before the first clock falling edge) 100 ns (min) tSU;STO Stop Condition SMBCLK High to SMBDAT Low (Stop Condition Setup) 100 ns (min) tSU;STA SMBus Repeated Start-Condition Setup Time, SMBCLK High to SMBDAT Low 0.6 µs (min) tBUF SMBus Free Time Between Stop and Start Conditions 1.3 µs (min) SMBus Communication 30015109 www.national.com 6 Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is guaranteed to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Operation of the device beyond the maximum Operating Ratings is not recommended. Note 2: Thermal resistance junction-to-ambient when attached to a printed circuit board with 1 oz. foil and no airflow is: θJA for MSOP-8 package = 210°C/W Note 3: Human body model (HBM) is a charged 100 pF capacitor discharged into a 1.5 kΩ resistor. Machine model (MM), is a charged 200 pF capacitor discharged directly into each pin. Charged Device Model (CDM) simulates a pin slowly acquiring charge (such as from a device sliding down the feeder in an automated assembler) then rapidly being discharged. Note 4: When the input voltage (VI) at any pin exceeds the power supplies (VI < GND or VI > VDD), the current at that pin should be limited to 5 mA. Parasitic components and or ESD protection circuitry are shown in the figures below for the LM95245's pins. Care should be taken not to forward bias the parasitic diodes on pins 2 and 3. Doing so by more than 50 mV may corrupt the temperature measurements. SNP refers to Snap-back device. Pin # Label Circuit 1 VDD B 2 D+ A 3 D− A 4 T_CRIT C 5 GND B 6 OS/A0 C 7 SMBDAT C Pin ESD Protection Structure Circuits Circuit A 8 SMBCLK Circuit B C Circuit C Note 5: Reflow temperature profiles are different for packages containing lead (Pb) than for those that do not. Note 6: Typical figures are at TA = 25°C and represent most likely parametric norms at the time of product characterization. The typical specifications are not guaranteed. Note 7: Limits are guaranteed to National's AOQL (Average Outgoing Quality Level). Note 8: Local temperature accuracy does not include the effects of self-heating. The rise in temperature due to self-heating is the product of the internal power dissipation of the LM95245 and the thermal resistance. See (Note 2) for the thermal resistance to be used in the self-heating calculation. Note 9: The accuracy of the LM95245 is guaranteed when using a typical thermal diode of an Intel processor on a 45 nm process, as selected in the Remote Diode Model Select register. See typical performance curve for performance with Intel processor on a 65nm or 90nm process. Note 10: This specification is provided only to indicate how often temperature data is updated. The LM95245 can be read at any time without regard to conversion state (and will yield last conversion result). Note 11: Quiescent current will not increase substantially when the SMBus is active. Note 12: The output rise time is measured from (VIN(0)max - 0.15V) to (VIN(1)min + 0.15V). Note 13: The output fall time is measured from (VIN(1)min + 0.15V) to (VIN(0)max - 0.15V). Note 14: Holding the SMBDAT and/or SMBCLK lines Low for a time interval greater than tTIMEOUT will reset the LM95245's SMBus state machine, therefore setting SMBDAT and SMBCLK pins to a high impedance state. 7 www.national.com LM95245 Notes LM95245 Typical Performance Characteristics Thermal Diode Capacitor or PCB Leakage Current Effect Remote Diode Temperature Reading Remote Temperature Reading Sensitivity to Thermal Diode Filter Capacitance, TruTherm Enabled 30015105 30015107 Conversion Rate Effect on Average Power Supply Current Intel Processor on 45nm Process, or 65nm Process Thermal Diode Performance Comparison 30015106 30015150 www.national.com 8 The LM95245 is a temperature sensor that measures Local and Remote temperature zones. The LM95245 uses a ΔVbe temperature sensing method. A differential voltage, representing temperature, is digitized using a Sigma-Delta analog to digital converter. TruTherm BJT (Transistor) Beta Compensation Technology allows the LM95245 to accurately sense the temperature of a thermal diode found on die fabricated using a sub-micron process. For more information on TruTherm Technology see Section 3.0 Application Hints. The LM95245 is compatible with the serial SMBus version 2.0 twowire serial interface. The LM95245 has OS and TCRIT open-drain digital outputs that indicate the state of the local and remote temperature readings when compared to user-programmable limits. If enabled, the local temperature is compared to the user-programmable Local Shared OS and TCRIT Limit Register (Default Value = 85°C). The comparison result can trigger the T_CRIT pin and/or the OS pin depending on the settings of the Local TCRIT Mask and OS Mask bits found in Configuration Register 1. The comparison result can also be read back from Status Register 1. If enabled, the remote temperature is compared to the user-programmable Remote TCRIT Limit Register (Default Value = 110°C), and the Remote OS Limit Register (Default Value = 85°C) values. The comparison result can trigger the T_CRIT pin and/or the OS pin depending on the settings of Configuration Register 1. The following table describes the default temperature settings for each measured temperature that triggers T_CRIT and/or OS pins: Output Pin Remote, °C Local, °C T_CRIT 110 85 OS 85 85 1.1 CONVERSION SEQUENCE In the power-up default state the LM95245 takes a maximum of 1 second to convert the Local Temperature, Remote Temperature, and to update all of its registers. Only during the conversion process is the Busy bit (D7) in Status Register 1 (02h) high. These conversions are addressed in a round-robin sequence. The conversion rate may be modified by the Conversion Rate bits found in the Conversion Rate Register (R/ W: 04h/0Ah). When the conversion rate is modified a delay is inserted between conversions, the actual maximum conversion time remains at 72 ms. Different conversion rates will cause the LM95245 to draw different amounts of supply current as shown in Figure 1. The following table describes the limit register mapping to the T_CRIT and/or OS pins: Output Pin Remote Local T_CRIT Remote TCRIT Limit Local Shared OS/TCRIT Limit OS Remote OS Limit Local Shared OS/TCRIT Limit The T_CRIT and OS outputs are open-drain, active low. The remote temperature readings support a programmable digital filter. Based on the settings in Configuration Register 2 a digital filter can be turned on to improve the noise performance of the remote temperature as well as to increase the resolution of the temperature reading. If the filter is enabled the filtered readings are used for TCRIT and OS comparisons. The LM95245 may be placed in low power consumption (Standby) mode by setting the STOP/RUN bit found in Configuration Register 1. In the Standby mode, the LM95245’s SMBus interface remains active while all circuitry not required is turned off. In the Standby mode the host can trigger one round of conversions by writing to the One-Shot Register. The value written into this register is not kept. Local and Remote temperatures will be converted once and the T_CRIT and OS pins will reflect the comparison results based on this set of conversions results. All the temperature readings are in 16-bit left-justified word format. The 10-bit plus sign local temperature reading is contained in two 8-bit registers: Local Temp MSB and Local Temp LSB Registers. The remote temperature supports both a 13bit unsigned and a 12-bit plus sign format. These readings are available in their corresponding registers as described in the 30015106 FIGURE 1. Conversion Rate Effect on Power Supply Current 1.2 POWER-ON-DEFAULT STATES LM95245 always powers up to these known default states. The LM95245 remains in these states until after the first conversion. 1. Command Register set to 00h 2. Conversion Rate register defaults to 02h (1 second). 3. Local Temperature set to 0°C until the end of the first conversion 4. Remote Diode Temperature set to 0°C until the end of the first conversion 5. Remote OS limit default is 55h (85 °C). 6. Local Shared and TCRIT limit default is 55h (85 °C). 7. Remote TCRIT limit default is 6Eh (110 °C). 8. Remote Offset High and Low bytes default to 00h. 9 www.national.com LM95245 LM95245 Register table. The lower 2-bits of the remote temperature reading will contain temperature information only if the digital filter is enabled. If the digital filter is disabled, these two bits will read back 0. The signed and unsigned remote temperature readings are available simultaneously in separate registers, therefore allowing both negative temperatures and temperatures 128°C and above to be measured. All Limit Registers support unsigned temperature format with 1°C LSb resolution. The Local Shared TCRIT and OS Limit Register is 7 bits for limits between 0°C and 127°C. The Remote Temperature TCRIT and OS Limit Registers are 8 bits each for limits between 0°C and 255°C. 1.0 Functional Description LM95245 9. Configuration Register 1 defaults to 00h. This sets the LM95245 as follows: A. The STOP/RUN defaults to the active/converting mode. B. The Local and Remote TCRIT and OS Masks are reset to 0. 10. Configuration Register 2 defaults to 1Fh. This sets the LM95245 as follows: A. B. C. D. E. FE1 FE0 Filter Setting 0 0 Filter Off 0 1 Reserved 1 0 Reserved 1 1 Filter On Figure 2 depicts the filter output in response to a step input and an impulse input. Remote Diode digital filter defaults on. The Remote Diode mode defaults to a typical Intel processor on 45/65/90 nm process. Diode Fault Mask bit for TCRIT defaults to 1. Diode Fault Mask bit for OS defaults to 0. Pin 6 Function defaults to Address Input function (A0). 1.3 SMBus INTERFACE The LM95245 operates as a slave on the SMBus, so the SMBCLK line is an input and the SMBDAT line is bidirectional. The LM95245 never drives the SMBCLK line and it does not support clock stretching. According to SMBus specifications, the LM95245 has a 7-bit slave address. Three SMBus addresses can be selected by connecting pin 6 (A0) to either Low, Mid-Supply or High voltages. The address selection table below shows two sets of possible selections for the LM95245CIMM and the LM95245CIMM-1. State of the A0 Pin LM95245CIMM SMBus Device Address 30015125 a) Seventeen and fifty degree step response LM95245CIMM-1 SMBus Device Address HEX Binary HEX Binary Low 18 001 1000 19 001 1001 Mid-Supply 29 010 1001 29 010 1001 High 4C 100 1100 4D 100 1100 30015126 The OS/A0 pin, after power-up, defaults as an address select input pin (A0). After power-up, the OS/A0 pin can only be programmed as an OS output when it is in the “High” state. Therefore, 4Ch is the only valid slave address that can be used when the OS/A0 pin is programmed to function as an OS output. When the OS/A0 pin is programmed to function as an A0 input the LM95245 will immediately detect the state of this pin to determine its SMBus slave address. The LM95245 does not latch the state of the A0 pin when it is functioning as an input. If the OS/A0 pin is not used it must be externally connected through hardware to some state, as shown in the table, in order to guarantee that the proper address is selected and not in an indeterminate state. The OS/ A0 does not have an internal pull-up. b) Impulse response with input transients less than 4°C 1.4 DIGITAL FILTER In order to suppress erroneous remote temperature readings due to noise, the LM95245 incorporates a digital filter for the Remote Temperature Channel. The filter is accessed in the Configuration Register 2, bits D2 (FE1) and D1(FE0). The filter can be set according to the following table. 30015128 c) Impuse response with input transients greater than 4°C FIGURE 2. Filter Impulse and Step Response Curves www.national.com 10 11-bit, unsigned binary Temperature Digital Output Binary Hex +255.875°C 1111 1111 1110 0000 FFE0h +255°C 1111 1111 0000 0000 FF00h +201°C 1100 1001 0000 0000 C900h +125°C 0111 1101 0000 0000 7D00h +25°C 0001 1001 0000 0000 1900h +1°C 0000 0001 0000 0000 0100h +0.125°C 0000 0000 0010 0000 0020h 0°C 0000 0000 0000 0000 0000h 13-bit, 2's complement (12-bit plus sign) Temperature 30015127 FIGURE 3. Digital Filter Response in a typical Intel processor on a 45nm, 65 nm or 90 nm process. The filter curves were purposely offset for clarity. 1.5 TEMPERATURE DATA FORMAT Temperature data can only be read from the Local and Remote Temperature registers. Remote temperature data with the digital filter off is represented by an 10-bit plus sign, two's complement word and 11bit unsigned binary word with an LSb (Least Significant Bit) equal to 0.125°C. The data format is a left justified 16-bit word available in two 8-bit registers. Unused bits report "0". Remote temperature data with the digital filter on is represented by a 12-bit plus sign, two's complement word and 13bit unsigned binary word with an LSb (Least Significant Bit) equal to 0.03125°C (1/32°C). The data format is a left justified 16-bit word available in two 8-bit registers. Unused bits report "0". Binary Hex +125°C 0111 1101 0000 0000 7D00h +25°C 0001 1001 0000 0000 1900h +1°C 0000 0001 0000 0000 0100h +0.03125°C 0000 0000 0000 1000 0008h 0°C 0000 0000 0000 0000 0000h −0.03125°C 1111 1111 1111 1000 FFF8h −1°C 1111 1111 0000 0000 FF00h −25°C 1110 0111 0000 0000 E700h −55°C 1100 1001 0000 0000 C900h 13-bit, unsigned binary Temperature 11-bit, 2's complement (10-bit plus sign) Temperature Digital Output Digital Output Digital Output Binary Hex +255.875°C 1111 1111 1110 0000 FFE0h +255°C 1111 1111 0000 0000 FF00h +201°C 1100 1001 0000 0000 C900h +125°C 0111 1101 0000 0000 7D00h +25°C 0001 1001 0000 0000 1900h +1°C 0000 0001 0000 0000 0100h Binary Hex +0.03125°C 0000 0000 0000 1000 0008h +125°C 0111 1101 0000 0000 7D00h 0°C 0000 0000 0000 0000 0000h +25°C 0001 1001 0000 0000 1900h +1°C 0000 0001 0000 0000 0100h +0.125°C 0000 0000 0010 0000 0020h 0°C 0000 0000 0000 0000 0000h −0.125°C 1111 1111 1110 0000 FFE0h −1°C 1111 1111 0000 0000 FF00h −25°C 1110 0111 0000 0000 E700h −55°C 1100 1001 0000 0000 C900h Local Temperature data is represented by a 10-bit plus sign, two's complement word with an LSb (Least Significant Bit) equal to 0.125°C. The data format is a left justified 16-bit word available in two 8-bit registers. Unused bits will always report "0". Local temperature readings greater than +127.875°C are clamped to +127.875°C, they will not roll-over to negative temperature readings. 11 www.national.com LM95245 Figure 3 shows the filter in use in a typical Intel processor on a 45/65/90 nm process system. Note that the two curves have been purposely offset for clarity. Inserting the filter does not induce an offset as shown. LM95245 1.8 OS OUTPUT AND OS LIMIT The LM95245's OS/A0 pin is selected as an OS digital output as described in Section 1.3. As an OS pin, it is activated whenever the local and/or remote temperature conversion is above the limits defined by the Limit registers. If the remote temperature exceeds the value in the Remote OS Limit Register the Status Bit for Remote OS (ROS) in Status Register 1 is set to 1. In the same way if the local temperature exceeds the value in the Local Shared OS and TCRIT Limit Register the Status Bit for the Shared Local OS and TCRIT (LOC) bit in Status Register 1 is set to 1. The state of the T_CRIT pin output will return to the HIGH state when both the Local and Remote temperatures are below the values programmed into the Limit Registers less the value in the Common Hysteresis Register. The OS output and the Status Register flags are updated after every Local and Remote temperature conversion. See Figure 5. 11-bit, 2's complement (10-bit plus sign) Temperature Digital Output Binary Hex +125°C 0111 1101 0000 0000 7D00h +25°C 0001 1001 0000 0000 1900h +1°C 0000 0001 0000 0000 0100h +0.125°C 0000 0000 0010 0000 0020h 0°C 0000 0000 0000 0000 0000h −0.125°C 1111 1111 1110 0000 FFE0h −1°C 1111 1111 0000 0000 FF00h −25°C 1110 0111 0000 0000 E700h −55°C 1100 1001 0000 0000 C900h 1.6 SMBDAT OPEN-DRAIN OUTPUT The SMBDAT output is an open-drain output and does not have internal pull-ups. A “high” level will not be observed on this pin until pull-up current is provided by some external source, typically a pull-up resistor. Choice of resistor value depends on many system factors but, in general, the pull-up resistor should be as large as possible without effecting the SMBus desired data rate. This will minimize any internal temperature reading errors due to internal heating of the LM95245. The maximum resistance of the pull-up to provide a 2.1V high level, based on LM95245 specification for High Level Output Current with the supply voltage at 3.0V, is 82 kΩ (5%) or 88.7 kΩ (1%). 1.7 T_CRIT OUTPUT AND TCRIT LIMIT The LM95245's T_CRIT pin is an active-low open-drain output that is triggered when the local and/or the remote temperature conversion is above the limits defined by the Remote and/or Local Limit registers. The state of the T_CRIT pin will return to the HIGH state when both the Local and Remote temperatures are below the values programmed into the Limit Registers less the value in the Common Hysteresis Register. Additionally, if the remote temperature exceeds the value in the Remote TCRIT Limit Register the Status Bit for Remote TCRIT (RTCRIT), in Status Register 1, is set to 1. In the same way if the local temperature exceeds the value in the Local Shared OS and TCRIT Limit Register the Status Bit for the Shared Local OS and TCRIT (LOC) bit in Status Register 1 is set to 1.The T_CRIT output and the Status Register flags are updated after every Local and Remote temperature conversion. See Figure 4 30015115 FIGURE 5. OS Temperature Response Diagram 1.9 DIODE FAULT DETECTION The LM95245 is equipped with operational circuitry designed to detect fault conditions concerning the remote diodes. In the event that the D+ pin is detected as shorted to GND, VDD or D+ is floating, the Remote Temperature reading is – 128.000 °C if signed format is selected and +255.875 °C if unsigned format is selected. In addition, the Status Register 1 bit D2 is set. 30015113 FIGURE 4. T_CRIT Comparator Temperature Response Diagram www.national.com 12 LM95245 1.10 COMMUNICATING with the LM95245 30015111 (a) Serial Bus Write to the Internal Command Register 30015110 (b) Serial Bus Write to the internal Command Register followed by a Data Byte 30015112 (c) Serial Bus byte Read from a Register with the internal Command Register preset to desired value. 30015114 (d) Serial Bus Write followed by a Repeat Start and Immediate Read FIGURE 6. SMBus Timing Diagrams for Access of Data (Default Address of 4Ch is shown) 13 www.national.com LM95245 The data registers in the LM95245 are selected by the Command Register. At power-up the Command Register is set to “00”, the location for the Read Local Temperature Register. The Command Register latches the last location it was set to. Each data register in the LM95245 falls into one of four types of user accessibility: 1. Read only 2. Write only 3. Write/Read same address 4. Write/Read different address A Write to the LM95245 will always include the address byte and the command byte. A write to any register requires one data byte. Reading the LM95245 can take place either of two ways: 1. If the location latched in the Command Register is correct (most of the time it is expected that the Command Register will point to one of the Read Temperature Registers because that will be the data most frequently read from the LM95245), then the read can simply consist of an address byte, followed by retrieving the data byte. 2. If the Command Register needs to be set, then an address byte, command byte, repeat start, and another address byte will accomplish a read. The data byte has the most significant bit first. At the end of a read, the LM95245 can accept either acknowledge or No Acknowledge from the Master (No Acknowledge is typically used as a signal for the slave that the Master has read its last byte). When retrieving all 11 bits from a previous remote diode temperature measurement, the master must insure that all 11 bits are from the same temperature conversion. This may be achieved by reading the MSB register first. The LSB will be www.national.com locked after the MSB is read. The LSB will be unlocked after being read. If the user reads MSBs consecutively, each time the MSB is read, the LSB associated with that temperature will be locked in and override the previous LSB value lockedin. 1.11 SERIAL INTERFACE RESET In the event that the SMBus Master is RESET while the LM95245 is transmitting on the SMBDAT line, the LM95245 must be returned to a known state in the communication protocol. This may be done in one of two ways: 1. When SMBDAT is LOW, the LM95245 SMBus state machine resets to the SMBus idle state if either SMBDAT or SMBCLK are held low for more than 35 ms (tTIMEOUT). Note that according to SMBus specification 2.0 all devices are to timeout when either the SMBCLK or SMBDAT lines are held low for 25 - 35 ms. Therefore, to insure a timeout of all devices on the bus the SMBCLK or SMBDAT lines must be held low for at least 35 ms. 2. When SMBDAT is HIGH, have the master initiate an SMBus start. The LM95245 will respond properly to an SMBus start condition at any point during the communication. After the start the LM95245 will expect an SMBus Address address byte. 1.12 ONE-SHOT CONVERSION The One-Shot register is used to initiate a single conversion and comparison cycle when the device is in standby mode, after which the device returns to standby. This is not a data register and it is the write operation that causes the one-shot conversion. The data written to this address is irrelevant and is not stored. A zero will always be read from this register. 14 Command register selects which registers will be read from or written to. Data for this register should be transmitted during the Command Byte of the SMBus write communication. POR means Power-On Reset. P0-P7: Command P7 P6 P5 P4 P3 P2 P1 P0 Command Register Summary Register Name Read Write Address Address (Hex) (Hex) No. of bits POR Read/ Default Write (Hex) Description TEMPERATURE SIGNED VALUE REGISTERS Local Temp MSB 0x00 NA 8 − RO Supports SMBus byte Local Temp LSB 0x30 NA 3 − RO All unused bits are reported as "0". Remote Temp MSB – Signed 0x01 NA 8 − RO Supports SMBus byte Remote Temp LSB – Signed 0x10 NA 5/3 − RO All unused bits are reported as "0". TEMPERATURE UNSIGNED VALUE REGISTERS Remote Temp MSB – Unsigned 0x31 NA 8 − RO Supports SMBus byte reads Remote Temp LSB – Unsigned 0x32 NA 5/3 − RO All unused bits are reported as "0". DIODE CONFIGURATION REGISTERS Configuration Register 2 0xBF 0xBF 5 0x1F R/W Filter Enable, Diode Model Select, Diode Fault Mask; Pin 6 OS/A0 function select Remote Offset High Byte 0x11 0x11 8 0x00 R/W 2's Complement Remote Offset Low Byte 0x12 0x12 3 0x00 R/W 2's Complement All unused bits are reported as "0". 5 0x00 R/W STOP/RUN , Remote TCRIT mask, Remote OS mask, Local TCRIT mask, Local OS mask 2 0x02 R/W Continuous or specific settings GENERAL CONFIGURATION REGISTERS Configuration Register 1 Conversion Rate 0x03/ 0x09 0x09/ 0x03 0x04/0x0 0x04/0x0 A A NA 0x0F − − WO A write to this register activates one conversion if STOP/RUN bit = 1. Status Register 1 0x02 NA 5 − RO Busy bit, and status bits Status Register 2 0x33 NA 2 − RO Not Ready bit Remote OS Limit 0x07/ 0x0D 0x0D/ 0x07 8 0x55 R/W Unsigned 0 to 255 °C Default 85 °C Local Shared OS and T_Crit Limit 0x20 0x20 7 0x55 R/W Unsigned 0 to 127 °C Default 85 °C Remote T_Crit Limit 0x19 0x19 8 0x6E R/W Unsigned 0 to 255 °C Default 110 °C Common Hysteresis 0x21 0x21 5 0x0A R/W up to 31°C One-Shot STATUS REGISTERS LIMIT REGISTERS 15 www.national.com LM95245 2.0 LM95245 Registers LM95245 Read Write Address Address (Hex) (Hex) Register Name No. of bits POR Read/ Default Write (Hex) Description IDENTIFICATION REGISTERS Manufacturer ID 0xFE 0x01 RO Always returns 0x01 Revision ID 0xFF 0xB3 RO Returns revision number. 2.1 LOCAL and REMOTE MSB and LSB TEMPERATURE REGISTERS Local Temperature MSB (Read Only Address 00h) 10-bit plus sign format: BIT D7 D6 D5 D4 D3 D2 D1 D0 Value SIGN 64 32 16 8 4 2 1 Temperature Data: LSb = 1°C. Local Temperature LSB (Read Only Address 30h) 10-bit plus sign format: BIT D7 D6 D5 D4 D3 D2 D1 D0 Value 0.5 0.25 0.125 0 0 0 0 0 Temperature Data: LSb = 0.125°C. Signed Remote Temperature MSB (Read Only Address 01h) 12-bit plus sign format: BIT D7 D6 D5 D4 D3 D2 D1 D0 Value SIGN 64 32 16 8 4 2 1 Temperature Data: LSb = 1°C. Signed Remote Temperature LSB, Filter On (Read Only Address 10h) 12-bit plus sign binary formats with filter on: BIT D7 D6 D5 D4 D3 D2 D1 D0 Value 0.5 0.25 0.125 0.0625 0.03125 0 0 0 Signed Remote Temperature LSB, Filter Off (Read Only Address 10h) 12-bit plus sign binary formats with filter off: BIT D7 D6 D5 D4 D3 D2 D1 D0 Value 0.5 0.25 0.125 0 0 0 0 0 Temperature Data: LSb = 0.125°C filter off or 0.03125°C filter on. www.national.com 16 LM95245 Unsigned Remote Temperature MSB (Read Only Address 31h) 13-bit unsigned format: BIT D7 D6 D5 D4 D3 D2 D1 D0 Value 128 64 32 16 8 4 2 1 Temperature Data: LSb = 1°C. Unsigned Remote Temperature LSB, Filter On (Read Only Address 32h) 13-bit unsigned binary formats with filter on: BIT D7 D6 D5 D4 D3 D2 D1 D0 Value 0.5 0.25 0.125 0.0625 0.03125 0 0 0 Unsigned Remote Temperature LSB, Filter Off (Read Only Address 32h) 13-bit unsigned binary formats with filter off: BIT D7 D6 D5 D4 D3 D2 D1 D0 Value 0.5 0.25 0.125 0 0 0 0 0 Temperature Data: LSb = 0.125°C filter off or 0.03125°C filter on. For data synchronization purposes, the MSB register should be read first if the user wants to read both MSB and LSB registers. The LSB will be locked after the MSB is read. The LSB will be unlocked after being read. If the user reads MSBs consecutively, each time the MSB is read, the LSB associated with that temperature will be locked in and override the previous LSB value lockedin. 2.2 DIODE CONFIGURATION REGISTERS Configuration Register 2 (Read/write Address BFh): D7 D6 D5 D4 D3 D2 D1 D0 0 OS/A0 Function Select OS Fault Mask T_CRIT Mask TruTherm Select RFE1 RFE0 1 Bits Name Description 7 Reserved Reports "0" when read. 6 OS/A0 Function Select 0: Address (A0) function is enabled 1: Over-temperature Shutdown (OS) is enabled 5 Diode Fault Mask for OS 0: Off 1: On 4 Diode Fault Mask for T_CRIT 0: Off 1: On 3 Remote Diode TruTherm Mode Select 0: Selects Diode Model 2, MMBT3904, with TruTherm technology disabled. Note, performance in this mode is not guaranteed. 1: Selects Diode Model 1, A typical Intel Processor, with 45nm, 65 nm or 90 nm technology, and TruTherm technology enabled. Remote Filter Enable 00: Filter Disable 01: Reserved 10: Reserved 11: Filter Enable Reserved Reports "1" when read. 2-1 0 Power up default is 1Fh. 17 www.national.com LM95245 Remote Offset High Byte (2's Complement) (R/W Address 11h) 10-bit plus sign format: BIT D7 D6 D5 D4 D3 D2 D1 D0 Value SIGN 64 32 16 8 4 2 1 Power up default is 00h. Remote Offset Low Byte (2's Complement) (R/W Address 12h) 10-bit plus sign format: BIT D7 D6 D5 D4 D3 D2 D1 D0 Value 0.50 0.25 0.125 0 0 0 0 0 Power up default is 00h. LSb = 0.125 °C. 2.3 GENERAL CONFIGURATION REGISTERS Configuration Register 1 (Read/write Address 03h/09h or 09h/03h): D7 D6 D5 D4 0 STOP/RUN 0 Remote T_CRIT Mask Bits D3 D2 Remote OS Mask Local T_CRIT Mask Name Description 7 Reserved Reports "0" when read. 6 STOP/RUN 0: Active / Converting 1: Standby 5 Reserved Reports "0" when read. 4 Remote T_CRIT Mask 0: Off 1: On 3 Remote OS Mask 0: Off 1: On 2 Local T_CRIT Mask 0: Off 1: On 1 Local OS Mask 0: Off 1: On 0 Reserved Reports "0" when read. D1 D0 Local OS Mask 0 Power up default is 00h. Conversion Rate Register (Read/write Address 04h/0Ah or 0Ah/04h):2-bit format: BIT D7 D6 D5 D4 D3 D2 D1 D0 Value 0 0 0 0 0 0 MSb LSb Bits Name 7:2 Reserved 1:0 www.national.com Description Reports "0" when read. 00: Continuous (33 ms typical when remote diode is missing or fault or 63 ms typical with remote diode connected) Conversion Rate 01: 0.364 seconds 10: 1 second 11: 2.5 seconds 18 LM95245 Power up default is 02h (1 second). One Shot Register (Write Only Address 0Fh): Writing to this register will start one conversion if the device is in standby mode (i.e. STOP/RUN bit = 1). 2.4 STATUS REGISTERS Status Register 1 (Read Only Address 02h): D7 D6 D5 D4 D3 D2 D1 D0 Busy 0 0 ROS 0 Diode Fault RTCRIT LOC Bits 7 Name Description Busy When set to "1" the part is converting. Reserved Report "0" when read. 4 ROS Status Bit for Remote OS 3 Reserved Reports "0" when read. Diode Fault Status bit for missing diode (Either D+ is shorted to GND, or VDD; or D+ is floating.) Note: The unsigned registers will report 0°C if read; the signed value registers will report −128.000°C. 1 RTCRIT Status bit for Remote TCRIT. 0 LOC Status bit for the shared Local OS and TCRIT . 6-5 2 Status Register 2 (Read Only Address 33h): D7 D6 D5 D4 D3 D2 D1 D0 Not Ready Reserved 0 0 0 0 0 0 Bits Name Description 7 Not Ready Waiting for 30 ms power-up sequence to end. 6 Reserved Can report "0" or "1" when read. 5-0 Reserved Reports "0" when read. 2.5 LIMIT REGISTERS Unsigned Remote OS Limit - 0°C to 255°C (Read/Write Address 07h/0Dh or 0Dh/07h): D7 D6 D5 D4 D3 D2 D1 D0 128 64 32 16 8 4 2 1 Power on Reset default is 55h (85°C). Unsigned Local Shared OS and T_CRIT Limit - 0°C to 127°C (Read/Write Address 20h): D7 D6 D5 D4 D3 D2 D1 D0 128 64 32 16 8 4 2 1 Power on Reset default is 55h (85°C). 19 www.national.com LM95245 Unsigned Remote T_CRIT Limit - 0°C to 255°C (Read/Write Address 19h): D7 D6 D5 D4 D3 D2 D1 D0 128 64 32 16 8 4 2 1 Power on Reset default is 6Eh (110°C). Common Hysteresis Register (Read/Write Address 21h): D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 16 8 4 2 1 Power on Reset default is 0Ah (10°C). 2.6 IDENTIFICATION REGISTERS Manufacturers ID Register (Read Only Address FEh): Always returns 01h. D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 1 Revision ID Register (Read Only Address FFh): Default is B3h. This register will increment by 1 every time there is a revision to the die by National Semiconductor. The initial revision bits for B3h are shown below. D7 D6 D5 D4 D3 D2 D1 D0 1 0 1 1 0 0 1 1 The LM95245 has been optimized to measure the remote thermal diode integrated in a typical Intel processor on 45 nm, 65 nm or 90 nm process. Using the Remote Diode Model Select register the remote inputs must be assigned to sense a typical Intel processor on 45nm, 65 nm or 90 nm process. 3.0 Applications Hints The LM95245 can be applied easily in the same way as other integrated-circuit temperature sensors, and its remote diode sensing capability allows it to be used in new ways as well. It can be soldered to a printed circuit board, and because the path of best thermal conductivity is between the die and the pins, its temperature will effectively be that of the printed circuit board lands and traces soldered to the LM95245's pins. This presumes that the ambient air temperature is almost the same as the surface temperature of the printed circuit board; if the air temperature is much higher or lower than the surface temperature, the actual temperature of the LM95245 die will be at an intermediate temperature between the surface and air temperatures. Again, the primary thermal conduction path is through the leads, so the circuit board temperature will contribute to the die temperature much more strongly than will the air temperature. To measure temperature external to the LM95245's die, use a remote diode. This diode can be located on the die of a target IC, allowing measurement of the IC's temperature, independent of the LM95245's temperature. A discrete diode can also be used to sense the temperature of external objects or ambient air. Remember that a discrete diode's temperature will be affected, and often dominated, by the temperature of its leads. Most silicon diodes do not lend themselves well to this application. It is recommended that an MMBT3904 transistor base-emitter junction be used with the collector tied to the base. Accuracy using the MMBT3904 is not guaranteed. For applications requiring the use of the MMBT3904 use the LM95235. The LM95245's BJT Beta Compensation TruTherm technology allows accurate sensing of integrated thermal diodes, such as those found on most processors. www.national.com 3.1 DIODE NON-IDEALITY 3.1.1 Diode Non-Ideality Factor Effect on Accuracy When a transistor is connected as a diode, the following relationship holds for variables VBE, T and IF: (1) where: • • • • • • • 20 q = 1.6×10−19 Coulombs (the electron charge), T = Absolute Temperature in Kelvin k = 1.38×10−23 joules/K (Boltzmann's constant), η is the non-ideality factor of the process the diode is manufactured on, IS = Saturation Current and is process dependent, If = Forward Current through the base-emitter junction VBE = Base-Emitter Voltage drop LM95245 30015143 FIGURE 7. Thermal Diode Current Paths In the active region, the -1 term is negligible and may be eliminated, yielding the following equation 3.1.2 Calculating Total System Accuracy The voltage seen by the LM95245 also includes the IFRS voltage drop of the series resistance. The non-ideality factor, η, is the only other parameter not accounted for and depends on the diode that is used for measurement. Since ΔVBE is proportional to both η and T, the variations in η cannot be distinguished from variations in temperature. Since the nonideality factor is not controlled by the temperature sensor, it will directly add to the inaccuracy of the sensor. Intel thermal diode specifications for processors on 45nm process were not available at the publication of this document, therefore following examples will use the 65nm thermal diode specifications. For the for Intel processor on 65nm process, Intel specifies a +4.06%/−0.897% variation in η from part to part when the processor diode is measured by a circuit that assumes diode equation, Equation 4, as true. As an example, assume a temperature sensor has an accuracy specification of ±1.0°C at a temperature of 80°C (353 Kelvin) and the processor diode has a non-ideality variation of +1.19%/−0.27%. The resulting system accuracy of the processor temperature being sensed will be: (2) In Equation 2, η and IS are dependant upon the process that was used in the fabrication of the particular diode. By forcing two currents with a very controlled ratio(IF2 / IF1) and measuring the resulting voltage difference, it is possible to eliminate the IS term. Solving for the forward voltage difference yields the relationship: (3) Solving Equation 3 for temperature yields: TACC = + 1.0°C + (+4.06% of 353 K) = +15.3 °C and (4) TACC = - 1.0°C + (−0.89% of 353 K) = −4.1 °C Equation 4 holds true when a diode connected transistor such as the MMBT3904 is used. When this “diode” equation is applied to an integrated diode such as a processor transistor with its collector tied to GND as shown in Figure 7 it will yield a wide non-ideality spread. This wide non-ideality spread is not due to true process variation but due to the fact that Equation 4 is an approximation. TruTherm technology uses the transistor (BJT) equation, Equation 5, which is a more accurate representation of the topology of the thermal diode found in an FPGA or processor. TrueTherm technology uses the transistor equation, Equation 4, resulting in a non-ideality spread that truly reflects the process variation which is very small. The transistor equation non-ideality spread is ±0.39% for the Pentium 4 processor on 90 nm process. The resulting accuracy when using TruTherm technology improves to: TACC = ±0.75°C + (±0.39% of 353 K) = ± 2.16 °C The next error term to be discussed is that due to the series resistance of the thermal diode and printed circuit board traces. The thermal diode series resistance is specified on most processor data sheets. For Intel processors in 65 nm process, this is specified at 4.52Ω typical. The LM95245 accommodates the typical series resistance of Intel Processor on 65 nm process. The error that is not accounted for is the spread of the processor's series resistance, that is 2.79Ω to 6.24Ω or ±1.73Ω. The equation to calculate the temperature error due to series resistance (TER) for the LM95245 is simply: (5) TruTherm should only be enabled when measuring the temperature of a transistor integrated as shown in the processor of Figure 7, because Equation 5 only applies to this topology. 21 www.national.com LM95245 2. A 100 pF diode bypass capacitor is recommended to filter high frequency noise but may not be necessary. Make sure the traces to the 100 pF capacitor are matched. Place the filter capacitors close to the LM95245 pins. 3. Ideally, the LM95245 should be placed within 10 cm of the Processor diode pins with the traces being as straight, short and identical as possible. Trace resistance of 1Ω can cause as much as 0.62°C of error. This error can be compensated by using simple software offset compensation. 4. Diode traces should be surrounded by a GND guard ring to either side, above and below if possible. This GND guard should not be between the D+ and D− lines. In the event that noise does couple to the diode lines it would be ideal if it is coupled common mode. That is equally to the D+ and D− lines. 5. Avoid routing diode traces in close proximity to power supply switching or filtering inductors. 6. Avoid running diode traces close to or parallel to high speed digital and bus lines. Diode traces should be kept at least 2 cm apart from the high speed digital traces. 7. If it is necessary to cross high speed digital traces, the diode traces and the high speed digital traces should cross at a 90 degree angle. 8. The ideal place to connect the LM95245's GND pin is as close as possible to the Processors GND associated with the sense diode. 9. Leakage current between D+ and GND and between D+ and D− should be kept to a minimum. Thirteen nanoamperes of leakage can cause as much as 0.2°C of error in the diode temperature reading. Keeping the printed circuit board as clean as possible will minimize leakage current. Noise coupling into the digital lines greater than 400 mVp-p (typical hysteresis) and undershoot less than 500 mV below GND, may prevent successful SMBus communication with the LM95245. SMBus no acknowledge is the most common symptom, causing unnecessary traffic on the bus. Although the SMBus maximum frequency of communication is rather low (100 kHz max), care still needs to be taken to ensure proper termination within a system with multiple parts on the bus and long printed circuit board traces. An RC lowpass filter with a 3 dB corner frequency of about 40 MHz is included on the LM95245's SMBCLK input. Additional resistance can be added in series with the SMBDAT and SMBCLK lines to further help filter noise and ringing. Minimize noise coupling by keeping digital traces out of switching power supply areas as well as ensuring that digital lines containing high speed data communications cross at right angles to the SMBDAT and SMBCLK lines. (6) Solving Equation 6 for RPCB equal to ±1.73Ω results in the additional error due to the spread in the series resistance of ±1.07°C. The spread in error cannot be canceled out, as it would require measuring each individual thermal diode device. This is quite difficult and impractical in a large volume production environment. Equation 6 can also be used to calculate the additional error caused by series resistance on the printed circuit board. Since the variation of the PCB series resistance is minimal, the bulk of the error term is always positive and can simply be cancelled out by subtracting it from the output readings of the LM95245. Processor Family Transistor Equation ηT, non-ideality Series R,Ω min typ max Intel Processor on 45 nm process NA NA NA NA Intel Processor on 65 nm process 0.997 1.001 1.005 4.52 Note: NA= Not Available at publication of this document. 3.2 PCB LAYOUT FOR MINIMIZING NOISE 30015117 FIGURE 8. Ideal Diode Trace Layout In a noisy environment, such as a processor mother board, layout considerations are very critical. Noise induced on traces running between the remote temperature diode sensor and the LM95245 can cause temperature conversion errors. Keep in mind that the signal level the LM95245 is trying to measure is in microvolts. The following guidelines should be followed: 1. VDD should be bypassed with a 0.1 µF capacitor in parallel with 100 pF. The 100 pF capacitor should be placed as close as possible to the power supply pin. A bulk capacitance of approximately 10 µF needs to be in the near vicinity of the LM95245. www.national.com 22 LM95245 Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead Molded Mini-Small-Outline Package (MSOP), JEDEC Registration Number MO-187 Order Number LM95245CIMM, LM95245CIMMX, LM95245CIMM-1, LM95245CIMMX-1 NS Package Number MUA08A 23 www.national.com LM95245 Precision Remote Diode Digital Temperature Sensor with TruTherm BJT Beta Compensation Technology for 45nm Process Notes THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2007 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530-85-86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +49 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560