AD AD8152 34 x 34, 3.2 gbps asynchronous digital crosspoint switch Datasheet

a
34 ⴛ 34, 3.2 Gbps
Asynchronous Digital Crosspoint Switch
AD8152*
FEATURES
Low Cost
Low Power
2.0 W @ 2.5 V (Outputs Enabled)
<100 mW @ 2.5 V (Outputs Disabled)
34 ⴛ 34, Fully Differential, Nonblocking Array
3.2 Gbps per Port NRZ Data Rate
Wide Power Supply Range: 2.5 V to 3.3 V
LVTTL or LVCMOS Level Control Inputs:
@ 2.5 V to 3.3 V
Low Jitter: 45 ps
Drives a Backplane Directly
Programmable Output Swing
100 mV to 1.6 V Differential
50 ⍀ On-Chip I/O Termination
User Controlled Voltage at the Load
Minimizes Power Dissipation
Dual Rank Latches
Available in 256-Ball Grid Array
APPLICATIONS
Fiber Optic Network Switching
High Speed Serial Backplane Routing to OC-48 with FEC
Gigabit Ethernet
Digital Video (HDTV)
Data Storage Networks
FUNCTIONAL BLOCK DIAGRAM
VCC
34
34
INP
OUTP
34 ⴛ 34
DIFFERENTIAL
SWITCH MATRIX
VTTI
34
OUTPUT
LEVEL
DACs
VTTO
34
OUTN
INN
D[5:0]
MATRIX
CONNECTION
LATCHES
CONNECTION
DECODE
OUTPUT
LEVEL
LATCHES
RESET
CS
A[6:0]
RE
CONTROL
LOGIC
WE
AD8152
UPDATE
VEE
GENERAL DESCRIPTION
The AD8152’s useful supply voltage range allows the user to
operate at LVPECL/CML data levels down to 2.5 V. The control
interface is LVTTL or LVCMOS compatible on 2.5 V to 3.3 V.
100mV/DIV
AD8152 is a member of the Xstream line of products and is a
breakthrough in digital switching, offering a large switch array
(34 × 34) on very little power, typically 2.0 W. Additionally, it
operates at data rates up to 3.2 Gbps per port, making it suitable
for Sonet/SDH OC-48 with Forward Error Correction (FEC).
The AD8152’s fully differential signal path reduces jitter and
crosstalk while allowing the use of smaller single-ended voltage
swings. It is offered in a 256-ball SBGA package that operates
over the industrial temperature range of 0°C to 85°C.
80ps/DIV
Figure 1. Eye Pattern, 3.2 Gbps, PRBS 23
*Patent Pending
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective companies.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© 2003 Analog Devices, Inc. All rights reserved.
AD8152
(@ 25ⴗC, VCC = 2.5 V to 3.3 V, VEE = 0 V, RL = 50 ⍀, Differential Output Swing = 800 mV p-p,
ELECTRICAL CHARACTERISTICS unless otherwise noted.)
Parameter
DYNAMIC PERFORMANCE
Max Data Rate/Channel (NRZ)
Channel Jitter
RMS Channel Jitter
Propagation Delay
Propagation Delay Match
Output Rise/Fall Time
INPUT CHARACTERISTICS
Input Voltage Swing
Input Voltage Range
Input Bias Current
Input Capacitance
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Voltage Range
Output Current
Output Capacitance
Condition
Min
Data Rate £ 3.2 Gbps; PRBS 223 – 1
VEE
50
VEE + 0.8
800
± 120
Differential (See TPC 18)
VEE = 0 V
100
800
VCC – 1.2
2
2
1600
VCC + 0.2
32
mV p-p
V
mA
pF
43
57
W
W/∞C
3.63
V
45
mA
mA
mA
mA
mA
All Outputs Disabled
All Outputs Enabled
All Outputs Disabled
All Outputs Enabled
TMIN to TMAX, All Outputs Enabled
LOGIC OUTPUT CHARACTERISTICS
Output High (VOH)
Output Low (VOL)
Output High (VOH)
Output Low (VOL)
VCC = 3.3 V, IOH = –2 mA
VCC = 3.3 V, IOL = +2 mA
VCC = 2.5 V, IOH = –100 uA
VCC = 2.5 V, IOL = +100 uA
50
0.05
32
190
32
770
800
45
2
0.8
1.7
0.7
2.4
0.4
2.1
0.2
0
Still Air
200 lfpm
400 lfpm
Gbps
ps p-p
ps
ps
ps
ps
mV p-p
V
mA
pF
2.25
VCC = 3.3 V
VCC = 3.3 V
VCC = 2.5 V
VCC = 2.5 V
Unit
1000
VCC + 0.2
2
2
LOGIC INPUT CHARACTERISTICS
Input High (VIH)
Input Low (VIL)
Input High (VIH)
Input Low (VIL)
THERMAL CHARACTERISTICS
Operating Temperature Range
␪JA
45
<10
660
± 50
100
20% to 80%
TERMINATION CHARACTERISTICS
Resistance
Temperature Coefficient
POWER SUPPLY
Operating Range
VCC
Quiescent Current
VCC
Max
3.2
Input to Output
Single-Ended (See TPC 14)
Common-Mode (See TPC 15)
Typ
85
15
12
11
V
V
V
V
V
V
V
V
∞C
∞C/W
∞C/W
∞C/W
Specifications subject to change without notice.
–2–
REV. A
AD8152
ABSOLUTE MAXIMUM RATINGS 1
16
Tj = 150ⴗC
MAXIMUM POWER DISSIPATION – W
VCC to VEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7 V
VTTI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC + 0.6 V
VTTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC + 0.6 V
Internal Power Dissipation2
AD8152 256-Ball SBGA (BP) . . . . . . . . . . . . . . . . . . 8.33 W
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC + 0.6 V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . 1.7 V
Logic Input Voltage . . . . . . VEE – 0.3 V < VIN < VCC + 0.6 V
Storage Temperature Range . . . . . . . . . . . . . –65°C to +125°C
Lead Temperature Range . . . . . . . . . . . . . . . . . . . . . . . 300°C
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
Specification is for the device in free air (T A = 25°C): ␪JA = 15°C/W @ still air.
14
12
400 lfpm
10
200 lfpm
8
STILL AIR
6
4
2
0
0
10
20
30
40
50
60
70
AMBIENT TEMPERATURE – ⴗC
90
Figure 2. Maximum Power Dissipation vs. Temperature
a shift in parametric performance due to a change in the stresses
exerted on the die by the package. Exceeding a junction temperature of 175°C for an extended period can result in device
failure. To ensure proper operation, it is necessary to observe the
maximum power derating curves shown in Figure 2.
MAXIMUM POWER DISSIPATION
The maximum power that can be safely dissipated by the AD8152 is
limited by the associated rise in junction temperature. The maximum safe junction temperature for plastic encapsulated devices
is determined by the glass transition temperature of the plastic,
approximately 150°C. Temporarily exceeding this limit may cause
ORDERING GUIDE
Model
Temperature Range
Package Description
AD8152JBP
AD8152-EVAL
0°C to 85°C
256-Ball SBGA (27 mm × 27 mm)
Evaluation Board
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although the
AD8152 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended
to avoid performance degradation or loss of functionality.
REV. A
80
–3–
AD8152
BALL GRID ARRAY
20
19
18
17
16
A
VEE
VEE
VEE
VEE
VCC
B
VEE
VEE
VEE
VEE
C
VEE
VEE
D4
D
D0
D1
E
CS
F
15
14
13
12
9
8
7
6
5
4
3
2
1
VTTO
O14P
VTTO
O11P
VCC
O08P
VTTO
O05P
VTTO
O02P
VTTO
VCC
VEE
VEE
VEE
A
VCC
VTTO
O14N
VTTO
O11N
VCC
O08N
VTTO
O05N
VTTO
O02N
VTTO
VCC
VEE
VEE
VEE
B
D5
O16N
O15P
O13N
O12P
O10N
O09P
O07N
O06P
O04N
O03P
O01N
O00P
A6
A5
VEE
VEE
C
D2
D3
O16P
O15N
O13P
O12N
O10P
O09N
O07P
O06N
O04P
O03N
O01P
O00N
A4
A3
A2
A1
D
RESET
N/C
N/C
N/C
N/C
UPDATE
A0
E
VCC
RE
I17P
I17N
I00N
I00P
WE
VCC
F
G
I19P
I19N
I18N
I18P
I01P
I01N
I02N
I02P
G
H
VTTI
VTTI
I20P
I20N
I03N
I03P
VTTI
VTTI
H
J
I22P
I22N
I21N
I21P
I04P
I04N
I05N
I05P
J
K
VTTI
VTTI
I23P
I23N
I06N
I06P
VTTI
VTTI
K
L
I25P
I25N
I24N
I24P
I07P
I07N
I08N
I08P
L
M
VCC
VCC
I26P
I26N
I09N
I09P
VCC
VCC
M
N
I28P
I28N
I27N
I27P
I10P
I10N
I11N
I11P
N
P
VTTI
VTTI
I29P
I29N
I12N
I12P
VTTI
VTTI
P
R
I31P
I31N
I30N
I30P
I13P
I13N
I14N
I14P
R
T
VTTI
VTTI
I32P
I32N
I15N
I15P
VTTI
VTTI
T
U
VCC
VCC
I33N
I33P
O33P
O32N
O30P
O29N
O27P
O26N
O24P
O23N
O21P
O20N
O18P
O17N
I16P
I16N
VCC
VCC
U
V
VEE
VEE
VEE
VEE
O33N
O32P
O30N
O29P
O27N
O26P
O24N
O23P
O21N
O20P
O18N
O17P
VEE
VEE
VEE
VEE
V
W
VEE
VEE
VEE
VEE
VCC
VTTO
O31N
VTTO
O28N
VCC
O25N
VTTO
O22N
VTTO
O19N
VTTO
VCC
VEE
VEE
VEE
W
Y
VEE
VEE
VEE
VEE
VCC
VTTO
O31P
VTTO
O28P
VCC
O25P
VTTO
O22P
VTTO
O19P
VTTO
VCC
VEE
VEE
VEE
Y
20
19
18
17
16
15
13
12
11
10
9
8
7
6
5
4
3
2
1
14
11
10
Ball Diagram, View from the Bottom
–4–
REV. A
AD8152
BALL GRID DESCRIPTIONS
Ball
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
Mnemonic
VEE
VEE
VEE
VCC
VTTO
OUT02P
VTTO
OUT05P
VTTO
OUT08P
VCC
OUT11P
VTTO
OUT14P
VTTO
VCC
VEE
VEE
VEE
VEE
VEE
VEE
VEE
VCC
VTTO
OUT02N
VTTO
OUT05N
VTTO
OUT08N
VCC
OUT11N
VTTO
OUT14N
VTTO
VCC
VEE
VEE
VEE
VEE
VEE
VEE
A5
A6
OUT00P
OUT01N
OUT03P
OUT04N
OUT06P
OUT07N
OUT09P
REV. A
Type
Power
Power
Power
Power
Power
I/O
Power
I/O
Power
I/O
Power
I/O
Power
I/O
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
I/O
Power
I/O
Power
I/O
Power
I/O
Power
I/O
Power
Power
Power
Power
Power
Power
Power
Power
Control
Control
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Description
Negative Supply
Negative Supply
Negative Supply
Positive Supply
Output Termination Supply
High Speed Output
Output Termination Supply
High Speed Output
Output Termination Supply
High Speed Output
Positive Supply
High Speed Output
Output Termination Supply
High Speed Output
Output Termination Supply
Positive Supply
Negative Supply
Negative Supply
Negative Supply
Negative Supply
Negative Supply
Negative Supply
Negative Supply
Positive Supply
Output Termination Supply
High Speed Output Complement
Output Termination Supply
High Speed Output Complement
Output Termination Supply
High Speed Output Complement
Positive Supply
High Speed Output Complement
Output Termination Supply
High Speed Output Complement
Output Termination Supply
Positive Supply
Negative Supply
Negative Supply
Negative Supply
Negative Supply
Negative Supply
Negative Supply
Output Address Pin (MSB)
Output Address Pin (Bank Des.)
High Speed Output
High Speed Output Complement
High Speed Output
High Speed Output Complement
High Speed Output
High Speed Output Complement
High Speed Output
Ball
C12
C13
C14
C15
C16
C17
C18
C19
C20
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
D19
D20
E1
E2
E3
E4
E17
E18
E19
E20
F1
F2
F3
F4
F17
F18
F19
F20
G1
G2
G3
G4
G17
G18
–5–
Mnemonic
OUT10N
OUT12P
OUT13N
OUT15P
OUT16N
D5
D4
VEE
VEE
A1
A2
A3
A4
OUT00N
OUT01P
OUT03N
OUT04P
OUT06N
OUT07P
OUT09N
OUT10P
OUT12N
OUT13P
OUT15N
OUT16P
D3
D2
D1
D0
A0
UPDATE
N/C Reserved
N/C Reserved
N/C Reserved
N/C Reserved
RESET
CS
VCC
WE
IN00P
IN00N
IN17N
IN17P
RE
VCC
IN02P
IN02N
IN01N
IN01P
IN18P
IN18N
Type
I/O
I/O
I/O
I/O
I/O
Control
Control
Power
Power
Control
Control
Control
Control
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Control
Control
Control
Control
Control
Control
Control
Control
Power
Control
I/O
I/O
I/O
I/O
Control
Power
I/O
I/O
I/O
I/O
I/O
I/O
Description
High Speed Output Complement
High Speed Output
High Speed Output Complement
High Speed Output
High Speed Output Complement
Input Address Pin (MSB)
Input Address Pin
Negative Supply
Negative Supply
Output Address Pin
Output Address Pin
Output Address Pin
Output Address Pin
High Speed Output Complement
High Speed Output
High Speed Output Complement
High Speed Output
High Speed Output Complement
High Speed Output
High Speed Output Complement
High Speed Output
High Speed Output Complement
High Speed Output
High Speed Output Complement
High Speed Output
Input Address Pin
Input Address Pin
Input Address Pin
Input Address Pin (LSB)
Output Address Pin (LSB)
Second Rank Write Enable
Do Not Connect
Do Not Connect
Do Not Connect
Do Not Connect
Reset/Disable Outputs
Chip Select Enable
Positive Supply
First Rank Write Enable
High Speed Input
High Speed Input Complement
High Speed Input Complement
High Speed Input
Readback Enable
Positive Supply
High Speed Input
High Speed Input Complement
High Speed Input Complement
High Speed Input
High Speed Input
High Speed Input Complement
AD8152
BALL GRID DESCRIPTIONS (continued)
Ball
G19
G20
H1
H2
H3
H4
H17
H18
H19
H20
J1
J2
J3
J4
J17
J18
J19
J20
K1
K2
K3
K4
K17
K18
K19
K20
L1
L2
L3
L4
L17
L18
L19
L20
M1
M2
M3
M4
M17
M18
M19
M20
N1
N2
N3
N4
N17
N18
N19
N20
P1
Mnemonic
IN19N
IN19P
VTTI
VTTI
IN03P
IN03N
IN20N
IN20P
VTTI
VTTI
IN05P
IN05N
IN04N
IN04P
IN21P
IN21N
IN22N
IN22P
VTTI
VTTI
IN06P
IN06N
IN23N
IN23P
VTTI
VTTI
IN08P
IN08N
IN07N
IN07P
IN24P
IN24N
IN25N
IN25P
VCC
VCC
IN09P
IN09N
IN26N
IN26P
VCC
VCC
IN11P
IN11N
IN10N
IN10P
IN27P
IN27N
IN28N
IN28P
VTTI
Type
I/O
I/O
Power
Power
I/O
I/O
I/O
I/O
Power
Power
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Power
Power
I/O
I/O
I/O
I/O
Power
Power
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Power
Power
I/O
I/O
I/O
I/O
Power
Power
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Power
Description
High Speed Input Complement
High Speed Input
Input Termination Supply
Input Termination Supply
High Speed Input
High Speed Input Complement
High Speed Input Complement
High Speed Input
Input Termination Supply
Input Termination Supply
High Speed Input
High Speed Input Complement
High Speed Input Complement
High Speed Input
High Speed Input
High Speed Input Complement
High Speed Input Complement
High Speed Input
Input Termination Supply
Input Termination Supply
High Speed Input Complement
High Speed Input
High Speed Input Complement
High Speed Input
Input Termination Supply
Input Termination Supply
High Speed Input
High Speed Input Complement
High Speed Input Complement
High Speed Input
High Speed Input
High Speed Input Complement
High Speed Input Complement
High Speed Input
Positive Supply
Positive Supply
High Speed Input
High Speed Input Complement
High Speed Input Complement
High Speed Input
Positive Supply
Positive Supply
High Speed Input
High Speed Input Complement
High Speed Input Complement
High Speed Input
High Speed Input
High Speed Input Complement
High Speed Input Complement
High Speed Input
Input Termination Supply
Ball
P2
P3
P4
P17
P18
P19
P20
R1
R2
R3
R4
R17
R18
R19
R20
T1
T2
T3
T4
T17
T18
T19
T20
U1
U2
U3
U4
U5
U6
U7
U8
U9
U10
U11
U12
U13
U14
U15
U16
U17
U18
U19
U20
V1
V2
V3
V4
V5
V6
V7
V8
–6–
Mnemonic
VTTI
IN12P
IN12N
IN29N
IN29P
VTTI
VTTI
IN14P
IN14N
IN13N
IN13P
IN30P
IN30N
IN31N
IN31P
VTTI
VTTI
IN15P
IN15N
IN32N
IN32P
VTTI
VTTI
VCC
VCC
IN16N
IN16P
OUT17N
OUT18P
OUT20N
OUT21P
OUT23N
OUT24P
OUT26N
OUT27P
OUT29N
OUT30P
OUT32N
OUT33P
IN33P
IN33N
VCC
VCC
VEE
VEE
VEE
VEE
OUT17P
OUT18N
OUT20P
OUT21N
Type
Power
I/O
I/O
I/O
I/O
Power
Power
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Power
Power
I/O
I/O
I/O
I/O
Power
Power
Power
Power
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Power
Power
Power
Power
Power
Power
I/O
I/O
I/O
I/O
Description
Input Termination Supply
High Speed Input
High Speed Input Complement
High Speed Input Complement
High Speed Input
Input Termination Supply
Input Termination Supply
High Speed Input
High Speed Input Complement
High Speed Input Complement
High Speed Input
High Speed Input
High Speed Input Complement
High Speed Input Complement
High Speed Input
Input Termination Supply
Input Termination Supply
High Speed Input
High Speed Input Complement
High Speed Input Complement
High Speed Input
Input Termination Supply
Input Termination Supply
Positive Supply
Positive Supply
High Speed Input Complement
High Speed Input
High Speed Output Complement
High Speed Output
High Speed Output Complement
High Speed Output
High Speed Output Complement
High Speed Output
High Speed Output Complement
High Speed Output
High Speed Output
High Speed Output
High Speed Output Complement
High Speed Output
High Speed Input
High Speed Input Complement
Positive Supply
Positive Supply
Negative Supply
Negative Supply
Negative Supply
Negative Supply
High Speed Output
High Speed Output Complement
High Speed Output
High Speed Output Complement
REV. A
AD8152
BALL GRID DESCRIPTIONS (continued)
Ball
V9
V10
V11
V12
V13
V14
V15
V16
V17
V18
V19
V20
W1
W2
W3
W4
W5
W6
W7
W8
W9
W10
W11
W12
W13
W14
Mnemonic
OUT23P
OUT24N
OUT26P
OUT27N
OUT29P
OUT30N
OUT32P
OUT33N
VEE
VEE
VEE
VEE
VEE
VEE
VEE
VCC
VTTO
OUT19N
VTTO
OUT22N
VTTO
OUT25N
VCC
OUT28N
VTTO
OUT31N
REV. A
Type
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Power
Power
Power
Power
Power
Power
Power
Power
Power
I/O
Power
I/O
Power
I/O
Power
I/O
Power
I/O
Description
High Speed Output
High Speed Output Complement
High Speed Output
High Speed Output Complement
High Speed Output
High Speed Output Complement
High Speed Output
High Speed Output Complement
Negative Supply
Negative Supply
Negative Supply
Negative Supply
Negative Supply
Negative Supply
Negative Supply
Positive Supply
Output Termination Supply
High Speed Output Complement
Output Termination Supply
High Speed Output Complement
Output Termination Supply
High Speed Output Complement
Positive Supply
High Speed Output Complement
Output Termination Supply
High Speed Output Complement
Ball
W15
W16
W17
W18
W19
W20
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Y8
Y9
Y10
Y11
Y12
Y13
Y14
Y15
Y16
Y17
Y18
Y19
Y20
–7–
Mnemonic
VTTO
VCC
VEE
VEE
VEE
VEE
VEE
VEE
VEE
VCC
VTTO
OUT19P
VTTO
OUT22P
VTTO
OUT25P
VCC
OUT28P
VTTO
OUT31P
VTTO
VCC
VEE
VEE
VEE
VEE
Type
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
I/O
Power
I/O
Power
I/O
Power
I/O
Power
I/O
Power
Power
Power
Power
Power
Power
Description
Output Termination Supply
Positive Supply
Negative Supply
Negative Supply
Negative Supply
Negative Supply
Negative Supply
Negative Supply
Negative Supply
Positive Supply
Output Termination Supply
High Speed Output
Output Termination Supply
High Speed Output
Output Termination Supply
High Speed Output
Positive Supply
High Speed Output
Output Termination Supply
High Speed Output
Output Termination Supply
Positive Supply
Negative Supply
Negative Supply
Negative Supply
Negative Supply
AD8152–Typical Performance Characteristics (2.5 V Supply, VCC = VTTI = VTTO, Data Rate = 3.2 Gbps;
100mV/DIV
100mV/DIV
PRBS 223–1; Differential Output Swing = 800 mV p-p; RL = 50 ⍀; Input Amplitude = 0.4 V p-p Single-Ended; unless otherwise noted.)
80ps/DIV
200ps/DIV
TPC 4. Eye Pattern 1.5 Gbps
100mV/DIV
100mV/DIV
TPC 1. Eye Pattern 3.2 Gbps
PEAK-PEAK JITTER = 35ps STD DEV = 5.1ps
PEAK-PEAK JITTER = 35ps STD DEV = 5.2ps
20ps/DIV
20ps/DIV
TPC 5. Jitter @ 1.5 Gbps
100mV/DIV
100mV/DIV
TPC 2. Jitter @ 3.2 Gbps
1.2ns/DIV
2.5ns/DIV
TPC 3. Response, 3.2 Gbps, 32-Bit Pattern
1111 1111 0000 0000 1010 1010 1100 1100
TPC 6. Response, 1.5 Gbps, 32-Bit Pattern
1111 1111 0000 0000 1010 1010 1100 1100
–8–
REV. A
AD8152
1.E+00
1400
BIN WIDTH = 5ps
1.E–01
1200
1.E–02
1.E–03
BIT ERROR RATE
FREQUENCY
1000
800
600
400
1.E–04
1.E–05
1.E–06
1.E–07
1.E–08
1.E–09
1.E–10
200
1.E–11
0
–50
–40
–30
–20
–10
0
10
20
40
30
1.E–12
–0.5
50
DUTY CYCLE DISTORTION – ps
TPC 7. Duty Cycle Distortion Distribution
–0.4
–0.3
–0.2
–0.1
0
0.1
UNIT INTERVAL
0.2
0.3
0.4
0.5
TPC 10. Bit Error Rate vs. Unit Interval
100
90
80
60
%EYE HEIGHT =
VOUT @ DATA RATE
ⴛ100
VOUT @ 0.5Gbps
50
100mV/DIV
EYE HEIGHT – %
70
40
30
20
10
0
0.5
1.0
1.5
2.0
2.5
DATA RATE – Gbps
3.0
3.5
4.0
PEAK-PEAK JITTER = 35ps STD DEV = 5.6ps
TPC 8. Eye Height vs. Data Rate
80ps/DIV
TPC 11. Crosstalk, 3.2 Gbps, Attack Signal OFF
(See TPC 25)
50
45
40
PEAK-PEAK JITTER
30
25
100mV/DIV
JITTER – ps
35
20
15
STANDARD DEVIATION
10
5
0
1.0
1.5
2.0
2.5
3.0
DATA RATE – Gbps
3.5
4.0
TPC 9. Jitter vs. Data Rate
PEAK-PEAK JITTER = 46ps STD DEV = 6.5ps
80ps/DIV
TPC 12. Crosstalk, 3.2 Gbps, Attack Signal ON
(See TPC 25)
REV. A
–9–
AD8152
55
80
70
50
PEAK-PEAK JITTER – ps
60
45
JITTER – ps
1.5 Gbps
40
3.2 Gbps
35
50
PEAK-PEAK JITTER
40
30
20
STANDARD DEVIATION
30
10
25
0
10
20
30
40
50
60
70
80
0
1.8 2.0
90
2.2
2.4
TEMPERATURE – ⴗC
2.8
3.0
3.2
3.4
3.6
3.8
4.0
TPC 16. Jitter vs. Supply
TPC 13. Single Point Jitter vs. Temperature
120
160
140
PEAK-PEAK JITTER – ps
100
80
JITTER – ps
2.6
SUPPLY VOLTAGE – V
60
PEAK–PEAK JITTER
40
120
IOUT = 16mA
100
IOUT = 24mA
80
IOUT = 32mA
60
40
20
20
STANDARD DEVIATION
0
10
100
INPUT AMPLITUDE – mV
0
0
–1.4
1000
–1.2
–1.0
–0.8
–0.6
–0.4
–0.2
0
VOL – V
TPC 14. Jitter vs. Single-Ended Input Amplitude
TPC 17. Jitter vs. VOL (Relative to VCC)
180
50
INPUT AMPLITUDE = 50mV p-p
45
160
PEAK–PEAK JITTER
140
35
120
JITTER – ps
PEAK-PEAK JITTER – ps
40
100
@3.3V
@2.5V
80
30
25
20
15
60
10
STANDARD DEVIATION
40
20
0.5
5
0.8
1.1
1.4
1.7
2.0
2.3
2.6
2.9
3.2
3.5
0
3.8
INPUT CML – V
0
5
10
15
20
25
30
35
IOUT – mA
TPC 18. Jitter vs. Programmed IOUT
TPC 15. Jitter vs. Input Common-Mode Level
–10–
REV. A
AD8152
750
160
BIN WIDTH = 5ps
140
PROPAGATION DELAY – ps
725
FREQUENCY
120
100
80
60
40
700
675
650
625
20
0
600
625
650
675
700
PROPAGATION DELAY – ps
725
600
2.0
750
800
780
740
720
IOUT – mA
PROPAGATION DELAY – ps
760
700
680
660
640
620
0
10
20
30
40
50
60
TEMPERATURE – ⴗC
70
80
90
TPC 20. Propagation Delay vs. Temperature
REV. A
2.4
2.6
2.8
3.0
3.2
SUPPLY VOLTAGE – V
3.4
3.6
3.8
TPC 21. Propagation Delay vs. Supply
TPC 19. Variation in Propagation Delay
600
2.2
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
0
MEASURED
IDEAL
0
1
2
3
4
5
6
7 8 9 10 11 12 13 14 15 16
IOUT CODE
TPC 22. IOUT vs. IOUT Code
–11–
AD8152
VCC
VTTI
PATTERN
GENERATOR
DATA OUT
VTTO
IN##P
–6dB
HIGH SPEED
SAMPLING
OSCILLOSCOPE
–6dB
OUT##P
50⍀
AD8152
DATA OUT
IN##N
–6dB
–6dB
OUT##N
50⍀
TRIGGER OUT
VEE = –2.5V
TRIGGER IN
IOUT = 16mA, VOUT HI = 0V, V OUT LO = –0.4V
VIN AMPLITUDE = 400mV p-p SINGLE-ENDED, VIN HI = –0.2V PRBS 223 – 1
TPC 23. Negative Supply Test Circuit
2.5V
DATA OUT
VCC
VTTI
PATTERN
GENERATOR
0.1␮F
OUT##P
IN##P
–6dB
HIGH SPEED
SAMPLING
OSCILLOSCOPE
VTTO
0.1␮F
–6dB
50⍀
AD8152
DATA OUT
–6dB
OUT##N
IN##N
–6dB
50⍀
0.1␮F
0.1␮F
TRIGGER OUT
VEE
TRIGGER IN
IOUT = 16mA, VOUT HI = 2.5V, V OUT LO = 2.1V
VIN AMPLITUDE = 400mV p-p SINGLE-ENDED, VIN HI = 2.7V
PRBS 223– 1, INPUTS AND OUTPUTS ARE AC-COUPLED
TPC 24. Positive Supply Test Circuit
PATTERN
GENERATOR #1
ATTACK SIGNAL
DATA OUT
DATA OUT
VTTI
–6dB
–6dB
IN25P
IN25N
VTTO
OUT00P...OUT26P
OUT28P...OUT33P
50⍀
OUT00N...OUT26N
OUT28N...OUT33N
50⍀
HIGH SPEED
SAMPLING
OSCILLOSCOPE
AD8152
PATTERN
GENERATOR #2
DATA OUT
VCC
–6dB
IN24P
OUT27P
–6dB
50⍀
DATA OUT
–6dB
IN24N
OUT27N
–6dB
50⍀
TRIGGER OUT
VEE = –2.5V
TRIGGER IN
ATTACK SIGNAL APPLIED TO IN25. IN25 BROADCAST TO ALL OUTPUTS EXCEPT OUT27.
TWO SEPARATE PATTERN GENERATORS USED TO PROVIDE INPUT PATTERN TO AD8152.
OUTPUTS NOT CONNECTED TO OSCILLOSCOPE ARE TERMINATED WITH EXTERNAL 50⍀ TO GND.
TPC 25. Crosstalk Test Circuit
–12–
REV. A
AD8152
Table I. Address and Data Buses
Connection/Current Bit
Output Address Pins
A6
0 = CONNECTION LATCHES
1 = OUTPUT CURRENT LEVEL
A5
A4
A3
Data Pins
A2
A1
MSB
A0
D5
LSB
MSB
D4
D3
D2
D1
D0
LSB
Table II. Connection Data and Address Programming Examples
Connection/
Current Bit
Output Address Pins
Data Pins
(Used to Select Inputs)
Comments
0 = CONNECTION
A6
0
0
0
0
0
0
0
MSB
A5 A4
0 0
0 0
1 0
1 1
0 0
1 0
1 1
MSB
D5 D4
0 0
1 0
0 1
0 0
1 1
1 1
1 1
Program IN00 to OUT00
Program IN33 to OUT00
Program IN31 to OUT33
Broadcast IN00 to All Outputs
Disable OUT00
Disable OUT33
Disable All Outputs (Broadcast)
A3
0
0
0
1
0
0
1
A2
0
0
0
1
0
0
1
A1
0
0
0
1
0
0
1
LSB
A0
0
0
1
1
0
1
1
D3
0
0
1
0
1
1
1
D2
0
0
1
0
1
1
1
D1
0
0
1
0
1
1
1
LSB
D0
0
1
1
0
1
1
1
Table III. Output-Current Level Data and Address Programming Examples
Connection/
Current Bit
Output Address Pins
Data Pins
(Used to Select Inputs)
1 = CURRENT LEVEL
A6
1
1
1
1
MSB
A5 A4
0 0
0 0
1 0
1 1
MSB
D5
X
X
X
X
LSB
A3 A2 A1 A0
0 0 0 0
0 0 0 0
0 0 0 1
1 1 1 1
LSB
D4 D3 D2 D1 D0
X 0
0 0 0
X 1
1 1 1
X 0
1 1 1
X 1
0 0 0
Comments
Program OUT00 to Current—Code 00 (2 mA)
Program OUT00 to Current—Code 15 (32 mA)
Program OUT33 to Current—Code 07 (16 mA)
Broadcast Current—Code 08 to All
Outputs (18 mA)
Table IV. Basic Control Strobe Functions
RESET CS
WE
RE
UPD Function
0
1
1
1
1
1
X
X
0
X
X
0
X
X
1
0
X
1
X
X
X
X
0
0
REV. A
X
1
0
0
0
0
Global Reset. Disables all outputs and resets all output current to code 0111 (16 mA).
Disable All Control Signals. Signal matrix/currents remain the same. D5:D0 are high impedance.
Write Enable. Write D5:D0 data into first rank register addressed by A6:A0.
Single-Output Readback. Second rank register data for output A6:A0 appears on D5:D0.
Global Update. Copy all first rank data into second rank registers.
Transparent Write and Update. D5:D0 immediately control programming. Use RE as gating signal.
–13–
AD8152
CS
WE
A[6:0]INPUTS
D[5:0]INPUTS
tCSW
tAHW
CHW
tASW
tAHW
tWP
tDSW
tDHW
Figure 3a. First Rank Write Cycle
Table V. First Rank Write Cycle
Symbol
Parameter
Conditions
Min
Chip Select to Write Enable
Address to Write Enable
Data to Write Enable
TA = 25ⴗC
0
0
1
ns
ns
ns
0
0
0
ns
ns
ns
10
ns
tCSW
tASW
tDSW
Setup Time
tCHW
tAHW
tDHW
Hold Time
tWP
Width of Write Enable Pulse
VCC = 3.3 V
Chip Select from Write Enable
Address from Write Enable
Data from Write Enable
Typ
Max
Unit
CS
UPDATE
ENABLING
OUT[0:33][N:P]
OUTPUTS
TOGGLE
OUT[0:33][N:P]
OUTPUTS
DISABLING
OUT[0:33][N:P]
OUTPUTS
DATA FROM RANK 1
PREVIOUS RANK 2 DATA
DATA FROM RANK 1
DATA FROM RANK 2
tCSU
tUW
tCHU
tUOE
tUOD
tUOT
Figure 3b. Second Rank Update Cycle
Table VI. Second Rank Update Cycle
Symbol
Parameter
tCSU
tCHU
tUOE
tUOT
tUOD
Setup Time
Hold Time
Output Enable Times
Output Toggle Times
Output Disable Times
tUW
Width of Update Pulse
Chip Select to Update
Chip Select from Update
Update to Output Enable
Update to Output Reprogram
Update to Output Disabled
Conditions
Min
TA = 25ⴗC
0
0
VCC = 3.3 V
25
25
25
10
–14–
Typ
Max
Unit
45
45
45
ns
ns
ns
ns
ns
ns
REV. A
AD8152
CS
UPDATE
WE
ENABLING
OUT[0:33][N:P]
OUTPUTS
DISABLING
OUT[0:33][N:P]
OUTPUTS
INPUT {DATA 1}
INPUT {DATA 0}
tCSU
INPUT {DATA 2}
INPUT {DATA 1}
tCHU
tUW
tWOT
tUOT
tUOE
tWHU
tWOD
Figure 4a. Transparent Write and Update Cycle
Table VII. Transparent Update Cycle
Symbol
Parameter
Conditions
Min
TA = 25ⴗC
VCC = 3.3 V
0
0
Typ
Max
Unit
tCSU
tCHU
Setup Time
Hold Time
Chip Select to Update
Chip Select from Update
tUOE
tWOE*
Output Enable Times
Update to Output Enable
Write Enable to Output Enable
35
35
50
50
ns
ns
tUOT
tWOT
Output Toggle Times
Update to Output Reprogram
Write Enable to Output Reprogram
25
25
45
45
ns
ns
tUOD*
tWOD
Output Disable Times
Update to Output Disabled
Write Enable to Output Disabled
25
25
45
45
ns
ns
tWHU
Setup Time
Write Enable to Update
tUW
Width of Update Pulse
ns
ns
0
ns
10
ns
*Not shown
CS
RE
D[5:0]
INPUT
ADDR 1
A[5:0]
OUTPUTS
ADDR 2
DATA
{ADDR 1}
DATA {ADDR 2}
tCSR
tCHR
tRDE
tAA
tRHA
tRDD
Figure 4b. Second Rank Readback Cycle
Table VIII. Second Rank Readback Cycle
Symbol
Parameter
Conditions
Min
TA = 25ⴗC
VCC = 3.3 V
0
0
5
tCSR
tCHR
tRHA
Setup Time
Hold Time
Chip Select to Read Enable
Chip Select from Read Enable
Address from Read Enable
tRDE
tAA
Enable Time
Access Time
Data from Read Enable
Data from Address
REV. A
Typ
Unit
ns
ns
ns
15
15
–15–
Max
30
ns
ns
AD8152
RESET
DISABLING
OUT[0:33][N:P]
OUTPUTS
tTOD
tTW
Figure 5. Asynchronous Reset
Table IX. Asynchronous Reset
Symbol
tTOD
Disable Time
tTW
Width of Reset Pulse
Parameter
Conditions
Output Disable from Reset
TA = 25ⴗC
VCC = 3.3 V
CONTROL INTERFACE
The AD8152 control interface receives and stores the desired
connection matrix and output levels for the 34 input and 34 output
signal pairs. The interface consists of 34 rows of double-rank
6-bit latches, one for each output. The 6-bit data-word stored
in these latches indicates to which (if any) of the 34 inputs the
output will be connected, as well as the full-scale output current.
One output at a time can be preprogrammed by addressing the
output and writing the desired connection data or output current into the first rank of latches. This process can be repeated
until each of the desired output changes has been preprogrammed.
All output connections can then be programmed at once by passing
the data from the first rank of latches into the second rank. The
output connections always reflect the data programmed into the
second rank of latches and do not change until the first rank of
data is passed into the second rank.
Max
Unit
10
25
ns
ns
connected to the output specified with the A[5:0] pins. The most
significant bit is D5, and the least significant bit is D0. To disable
an output completely, the input address D[5:0] = “111111”
should be written into the input configuration bank at the desired
output address.
In write mode, when the bank selection bit A6 is HIGH, the
binary encoded data applied to pins D[3:0] indicate the output
current level to be used for the output specified with the A[5:0]
pins. The reset default is “0111” for 16 mA. Each LSB is 2 mA.
WE Input
At any time, a reset pulse can be applied to the control interface to
globally reset the appropriate second rank data bits, disabling all 34
signal output pairs and resetting the output currents. To facilitate
multiple chip address decoding, there is a chip select pin. All logic
signals except the reset pulse are ignored unless the chip select
pin is active. The chip select pin disables only the control logic
interface and does not change the operation of the signal matrix.
The chip select pin does not power down any of the latches, so any
data programmed in the latches is preserved.
All control pins are level-sensitive, not edge-triggered.
CONTROL PIN DESCRIPTION
A[6:0] Inputs
Output address pins. The binary encoded address applied to the
lower A[5:0] input pins determines which of the 34 outputs is
being programmed (or being read back). The most significant bit,
A6, determines whether the data pins contain information for
the connection register bank or the output level register bank.
Using the broadcast address, A[5:0] = “111111” will simultaneously program data into all outputs at once.
Input configuration or output level data pins. In write mode,
when the bank selection bit A6 is LOW, the binary encoded data
applied to pins D[5:0] determine which of the 34 inputs is to be
10
Typ
In readback mode, pins D[5:0] are low impedance outputs
indicating the data-word stored in the second rank for the output specified with the A[5:0] pins and the bank specified with
the A6 bit. The readback drivers were designed to drive high
impedances only, so external drivers connected to the D[5:0]
should be disabled during readback mode.
If necessary for system verification, the data in the second rank
of latches can be read back from the control interface.
D[5:0] Inputs/Outputs
Min
First rank write enable. Forcing this pin to logic low allows the
data on pins D[5:0] to be stored in the first rank latch for the
output specified by pins A[6:0]. The WE pin must be returned to a
logic high state after a write cycle to avoid overwriting the first
rank data.
UPDATE Input
Second rank write enable. Forcing this pin to logic low allows the
data stored in all 34 first rank latches (in both banks) to be transferred to the second rank latches. The signal connection matrix
will be reprogrammed when the second rank data and levels are
changed. This is a global pin, transferring all 34 rows of data at
once. It is not necessary to program the address pins. It should
be noted that after initial power-up of the device, the first rank
data is undefined. It is desirable to preprogram all 17 outputs
before performing the first update cycle.
RE Input
Second rank read enable. Forcing this pin to logic low enables the
output drivers on the bidirectional D[5:0] pins, entering the readback mode of operation. By selecting an output address with the
A[6:0] pins and forcing RE to logic low, the 6-bit data stored in
the second rank latch for that output address will be written to
D[5:0] pins. Data should not be written to the D[5:0] pins
externally while in readback mode. The RE is a higher priority
pin than the WE pin, so first rank programming is not possible
while in readback mode.
–16–
REV. A
AD8152
CS Input
Chip select. This pin must be forced to logic low to program or
receive data from the logic interface, with the exception of the
RESET pin, described below. This pin has no effect on the signal
pairs and does not alter any of the stored control data.
RESET Input
Global output disable pin. Forcing the RESET pin to logic low
will disable all outputs, setting both ranks of all 34 input connection latches, regardless of the state of any other pins. This has the
effect of immediately disabling the 34 output signal pairs in the
matrix. The output level information is also changed. It is necessary
to momentarily hold RESET at a logic low state when powering
up the AD8152 in order to avoid random internal contention
where multiple inputs may be connected to one output. The
RESET pin is not gated by the state of the chip select pin, CS.
If it is desired to program all outputs to the same current level,
then the broadcast Code 63 can be placed on the address bus
(A5:A0), along with A6 = 1. (D3:D0) will then program all output
currents to the same level.
When the current code is set to 0000, a minimum current level
of 2 mA is obtained. For any other code, the current can be
calculated by (current code) ¥ 2 mA + 2 mA. Refer to Table III.
For example, 16 mA can be programmed by Code 0111. This is
7 ¥ 2 mA + 2 mA = 16 mA.
Register-Control Signals
Several single-ended logic input pins control the register loading
associated with the address and data buses described in the previous section. The control functions are tabulated in Table IV.
Control Interface Levels
The AD8152 control interface shares the data path supply pins,
VCC and VEE. The potential between the positive logic supply
VCC and the negative supply VEE must be at least 2.25 V and no
more than 3.63 V. Regardless of supply, the logic threshold is
approximately one-half the supply range, allowing the interface
to be used with most LVCMOS and LVTTL logic drivers.
Output Addressing
The AD8152 is programmed using a memory interface module,
with parallel address and data buses. Six bits (A5:A0) are used to
address the outputs. By setting the decimal value of these address
bits to a value from 0 to 33 inclusive, then one of the 34 outputs
is uniquely addressed.
One additional code, 63 (all 1s), is used for the broadcast mode.
If this address is selected, then all outputs will receive the same
programming. The remaining addresses in the space are not
valid and are reserved, Codes 34 to 66 inclusive. (See Table I.)
Connection and Output Current Programming
A seventh address bit (A6) determines which of two types of
programming is selected. If A6 = 0, connection matrix programming is selected. If A6 = 1, output current programming is selected.
There are dual ranks of registers for the data that programs the
AD8152. The first rank registers accumulate the data for the
various outputs as they are being programmed one by one. The
second rank registers actually control the functions of the device.
The RESET signal is used to reset the connection matrix, disable
all outputs, and set all of the output currents to a default condition
at Code 0111. This action sets the output current to a nominal
value of 16 mA. The data in the first rank latches is also reset by
the assertion of RESET.
The CS signal is used to enable the control interface. If several
devices are used in a system with the other control signals
bussed, the CS signal can be used to select an individual device
to change its programming.
The WE signal is used to enable writing data to the first rank
registers. This data will not immediately affect the features of
the AD8152.
The UPDATE signal transfers the data from the first rank registers
to the second rank registers. After assertion of UPDATE, the
data actively controls the AD8152 functions.
The second rank registers can be read back through the data bus.
The output is addressed on A5:A0 and the connection/current is
selected via A6. Asserting RE will cause the second rank data to
appear on the data bus. The RE function will dominate over
WE if both are asserted at the same time. Broadcast readback is
not permitted.
Using the Data Bus
Once it is determined which output is to be programmed (or broadcast to all outputs) and which type of programming (connection/
output-current), then the data bits (D5:D0) further define the
programming action.
Some typical programming waveforms for the control signals are
provided in Figure 6.
If the selection is connection programming (A6 = 0), then the data
bits select the input that is to be connected to the addressed
output. If the broadcast address is selected, then the data bits select
the input that will be connected to all 34 outputs. (See Table II.)
A disable code (D5:D0 = 63, or all 1s) is used to disable (and
power down) the particular output that is addressed. A broadcast
disable can be effected by setting Code 63 on both the address
bus and the data bus along with A6 = 0.
VALID ADDRESS INPUT
VALID ADDRESS INPUT
D[5:0]
VALID DATA INPUT
VALID DATA INPUT
WE
UPDATE
Figure 6. Programming Waveforms
Output-Current Programming
A current source in each output can be digitally programmed to
any one of 16 different current levels. Changing these current
levels will change the amplitude of the output swing that is
developed across the internal 50 W termination resistors.
Input/Output Coupling
To program the current for a particular output, its address is set on
A5:A0 (00–33), while A6 is set to 1. The four LSBs of the data
address (D3:D0) are then used to select one of the 16 output
current levels. D4 and D5 are “don’t cares” for output current
programming. (See Table III.)
REV. A
A[6:0]
The AD8152 has internal 50 W termination resistors for each
single-ended input and output. This can also provide a 100 W
termination for a 100 W differential transmission line. All of the
input termination resistors connect to one common point called
VTTI. Similarly, each of the output termination resistors connects
to one common point called VTTO. The voltage can be set
independently at VTTI and VTTO to accommodate various
interface architectures.
–17–
AD8152
Input Coupling
One way to simplify the input circuit and make it compatible with
a wide variety of driving devices is to use ac coupling. This has
the effect of isolating the dc common-mode levels of the driver
and the AD8152 input circuitry. For example, the XAUI interconnect specification for 10 Gbps Ethernet requires ac coupling
in order to ensure that there are no interactions of dc levels
between the transmitting and receiving devices.
AC coupling requires that the signal patterns have no long-term
dc component, which may occur in any random data stream.
Codes such as 8b/10b, called for in the XAUI specification, are
used in many data communications systems to ensure that the
data pattern is benign in an ac-coupled link. This is accomplished
by run-length limiting (RLL), which sets a maximum for the
number of 1s or 0s that can occur consecutively. In addition,
residual dc components are monitored and modified by keeping
track of the running disparity, excess of 1s versus 0s or vice versa.
For the AD8152 inputs, ac coupling requires a capacitor in series
with each single-ended input signal, as shown in Figure 7. This
should be done in a manner that does not interfere with the high
speed signal integrity of the PC board. The details of this are
covered in the section on board layout guidelines. The two critical
variables are setting the proper voltage for VTTI and selecting
the correct value of coupling capacitors.
VTTI
CINP
50⍀
VCC
If VTTI is set equal to VCC, then the single-ended signal will
just meet the specifications where its highest excursion will be
0.2 V higher than VCC. The lowest level to set VTTI is 0.8 V
above VEE. This will cause the negative signal excursions to stay
within the operating range.
With ac-coupled inputs, there is no power consumption advantage associated with varying VTTI. As a practical matter, it
might be desirable to set VTTI at the same voltage as VTTO so
that only one supply is necessary. Refer to the VTTO section for
more information.
Output Coupling
Each single-ended output of the AD8152 has a termination
resistor that ties to a common point called VTTO. When VTTO
is varied, it will change the common-mode levels of the outputs
and the power dissipation of the output stages when they are
enabled.
The individual output currents are programmable. Varying this
current will change the lower level of the output voltage (and thus
the peak-to-peak swing) and also change the power dissipation in
the output stages. To obtain a standard 800 mV p-p differential
output (single-ended = 400 mV p-p), the output current should
be programmed to 16 mA. With an effective termination resistance of 25 W, this will generate the proper differential voltage.
If the AD8152 drives another device that is ac-coupled, there is no
interaction of the dc levels on each side of the coupling capacitors
(see Figure 8). The dc levels for the AD8152 can be calculated
independent of the levels of the device that is driven.
The upper allowable setting for VTTO is 0.2 V higher than VCC.
The signals will be pulled up to this level at their highest excursion.
However at this setting, the power dissipation will be a maximum.
50⍀
INXXP
INXXN
CINN
VEE
Figure 7. AC-Coupling Input Signal from AD8152
On the AD8152 side of the input coupling capacitor, the average
value of the single-ended input voltage will be at the voltage set at
VTTI. The range of allowable voltages is a function of the acceptable input voltages of the active circuitry of the AD8152 inputs
and the amplitude of the input signal. The operating input range
of the AD8152 extends from VCC + 0.2 V to 0.8 V above VEE.
To save power, VTTO can be lowered. The lowest level for
VTTO will be determined by the lowest output level allowable
(VOL) by the AD8152 output when it is logically low. The output
at any time should not go lower than 1.0 V below VCC. If the
single-ended swing of an output is 400 mV p-p, then the lowest
that VTTO can go is 0.6 V below VCC. For more information
on VOL, see TPC 17.
VCC
VTTO
VTT
VCC
AD8152
50⍀
50⍀
OUTXXP
OUTXXN
The total range that will be occupied by the input signal will be
its average value (as established by the voltage applied to VTTI)
plus or minus one half the single-ended swing of the signal. For a
standard 800 mV p-p differential signal, the single-ended swing is
400 mV p-p. Thus, the signal will swing ± 200 mV about the
average value equal to VTTI.
DRIVEN DEVICE
I = 2mA ⴛ (CODE) + 2mA
VEE
VEE
VEE
Figure 8. AC-Coupling Output Signal from AD8152
–18–
REV. A
AD8152
is powered down. Thus, the total number of active inputs will
affect the total power consumption.
AD8152 POWER CONSUMPTION
There are several sections of the AD8152 that draw varying
power depending on the supply voltages, the type of I/O coupling
used, and the status of the AD8152 operation. Figure 9 shows a
block diagram of these sections. These are described briefly below
and then in detail later in the data sheet. Table X summarizes the
power consumption of each section and is a useful guide as the
following sections are reviewed.
The core of the device performs the crosspoint switching function.
It draws a fixed quiescent current whenever the AD8152 is
powered from VCC to VEE.
An output predriver section draws a current that is proportional
to the programmed output current, IOUT. This current always
flows from VCC to VEE. It is treated separately from the output
current, which flows from VTTO, and might not be the same
voltage as VCC.
The first section is the input termination resistors. The power
dissipated in the termination resistors is the result of their being
driven by the respective driving stage. Also, there might be dc power
dissipated in the input termination resistors if the inputs are
dc-coupled and the driving source reference is a dc voltage that is
not equal to VTTI.
The final section is the outputs. For an individual output, the
programmed output current will flow through two separate paths.
One is the on-chip termination resistor, and the other is the
transmission line and the destination termination resistor. The
nominal parallel impedance of these two paths is 25 W. The sum
In the next section, the active part of the input stages, each input
is powered only when it is selected. If an input is not selected, it
VCC
VTT
VTTO
VTTI
OUTPUT TERMINATIONS
IOUT
50⍀
P=
50⍀
2
50⍀
50⍀
50⍀
50⍀
50⍀
DRIVEN DEVICE
TERMINATIONS
OUTP
INP
OUTN
INN
INPUT
TERMINATIONS
P=
(Vindiffrms)2
100⍀
INPUTS
I = 2mA
PER
ACTIVE
INPUT
OUTPUT
PREDRIVER
SWITCH
MATRIX
OPTIONAL COUPLING CAPACITORS
P = (VOL) (IOUT)
VOL = VTTO – (IOUT ⴛ 25⍀)
OUTPUTS
I = .25 IOUT
I = 32mA
IOUT
VEE
Figure 9. Power Consumption Block Diagram
Table X. Power Consumption
Input
Termination
Resistors
Input
Stage
Quiescent Current
Core
Output
Predriver
Output
Termination
Resistors
Output
Switch +
Current
Source
0.25 ¥ IOUT
0.5 ¥ IOUT
IOUT
4 mA
8 mA
16 mA
10 mW
340 mW
17%
8 mW
272 mW
13.6%
33.6 mW
1.03 W
51%
2.0 W
13.2 mW
449 mW
17%
8 mW
272 mW
10%
46.4 mW
1.47 W
56%
2.63 W
Total
Power
32 mA
Current per Active Channel
VIN /(RTERMINATION) 2 mA
Current per Active Channel
for Differential
VIN = 800 mV p-p Sine
VOUT = 800 mV p-p
566 mV rms/100
= 5.66 mA
2 mA
4 mA
2.5 V Operation (VCC – VEE = 2.5 V, VTTO = 2.5 V, IOUT = 16 mA)
Per Channel Power
Power for All Channels Active
Percentage of Total Power
3.2 mW
108.8 mW
5%
5 mW
170 mW
8%
80 mW
4%
3.3 V Operation (VCC – VEE = 3.3 V, VTTO = 3.3 V, IOUT = 16 mA)
Per Channel Power
Power for All Channels Active
Percentage of Total Power
REV. A
3.2 mW
108.8 mW
4%
6.6 mW
224 mW
9%
106 mW
4%
–19–
AD8152
of these two currents will flow through the switches and the current
source of the AD8152 output circuit and out through VEE.
The power dissipated in the transmission line and the destination
resistor will not be dissipated in the AD8152, but will have to be
supplied from the power supply, and is a factor in the overall system
power. The current in the on-chip termination resistors and the
output current source will dissipate power in the AD8152 itself.
OUTPUTS
The output current is forced by a current source that is programmed to a variable amount of current from 2 mA to 32 mA
in 2 mA steps. For the two logic switch states, this current flows
through an on-chip termination resistor and a parallel path to the
destination device and its termination resistor. The power in this
parallel path is not dissipated by the AD8152.
The nominal programmed output current is 16 mA. With the two
parallel 50 W resistors at each collector (25 W equivalent), this
current will create a 400 mV p-p swing in each half of the circuit.
The differential output voltage will be 800 mV p-p.
Input Termination Resistors
The power dissipated in the input termination resistors is
delivered by the driving source. First, assume the driving waveform for an individual input is a differential square wave with an
amplitude of Vinpp. Then the power dissipated in this input is
(Vinpp)2/2Rterm.
However, this result is quite pessimistic, because at high frequencies, the wave shape is usually more sinusoidal than square.
If instead, a differential sine wave of amplitude Vinpp is assumed,
then its rms amplitude is 0.7 times that of a square wave. This will
yield a power that is one half of the square wave case. The assumed
wave shape is not too critical because the fraction of the power
dissipated in the input termination resistors is not very large.
A further effect is that the input signal might travel over a path
that attenuates the signal. This will usually be a function of
frequency. Thus, for such a case, some of the signal power will
be dissipated in the signal path. This will reduce the amount of
power dissipated in the AD8152 input terminations.
If dc coupling is used, a dc current will flow from VTTI through
the termination resistors if the dc voltage of the drive circuit is not
equal to VTTI. The additional power in each input termination
resistor will be the current that flows multiplied by the 50 W
value of the input terminations.
Under steady state conditions and with a data pattern that is
run-length limited so that its low frequency content is significantly
higher than the RC pole formed by the coupling capacitor and the
termination resistors, the common-mode level at the AD8152
outputs will be 400 mV lower than VTTO. Each output will then
swing ± 200 mV from this level, which is a 400 mV p-p singleended output swing.
At the high level, there will be 200 mV across the termination
resistor. This will dissipate a power of 0.8 mW. At the low level, the
600 mV across the termination resistor will dissipate a power of
7.2 mW. Since the output signal is basically 50% duty cycle, the
average power dissipated will be the average of these two values
or 4 mW. By symmetry, the other differential output will dissipate
the same power. This yields an on-chip termination-resistor
power dissipation of 8 mW per channel for each output, or 272 mW
for all 34 outputs.
The full output current (from both on- and off-chip termination
resistors) will flow in the lower part of each output. This current
flows only in the side that is “on,” or in its low state (VOL). This
voltage is 600 mV below the dc level at VTTO.
For a point of reference, assume a channel has a sinusoidal input of
800 mV p-p differential. The power dissipated for a single input
will be 3.2 mW. If all 34 input channels are driven the same, then
the power in the input terminations will be 109 mW.
Thus, for VTTO = 2.5 V, VOL = 1.9 V, and the power dissipation for IOUT = 16 mA is 30.4 mA. For all 34 channels, the
power is 1.03 W.
Input Stage
If VTTO = 3.3 V, then VOL = 2.7 V. The single power is 43.2 mW
and the power for all 34 channels is 1.47 W.
The input stages are powered down when not in use. There is
about 2 mA that flows through an enabled input from VCC to VEE.
Thus, the power dissipated by an enabled input is 5 mW for a
supply of 2.5 V and 6.6 mW for a 3.3 V supply. For all 34 inputs
enabled, the respective figures are 170 mW for a 2.5 V supply
and 224 mW for a 3.3 V supply.
Switch Matrix
The switch matrix draws a fixed 32 mA when the AD8152 is
powered. This current flows from VCC to VEE. The power dissipation from this current is 80 mW at 2.5 V and 106 mW at 3.3 V.
Output Predrivers
The output predrivers draw additional current when each of the
outputs is enabled. This extra current is proportional to the
programmed output current. The extra predriver current for a
channel will be 25 percent of the programmed output current
for that channel. This current will also flow from VCC to VEE.
If VTTO = 2.5 V, then the additional power is given by 16 mA
¥ [(2.5 V – (16 mA ¥ 25 W)] = 33.6 mW. Thus, the total AD8152
power dissipation for this output is 37.6 mW.
If all 34 outputs are enabled with the same IOUT, the total power
dissipation is 1.28 W. Thus it can be seen that the outputs are
the major contributor to the power dissipation.
Power Saving Considerations
While the AD8152 power consumption is very low compared to
similar devices, careful control of its operating conditions can yield
further power savings. Significant power reduction can be realized
by operating the part at a lower voltage. Compared to 3.3 V
operation, a supply voltage of 2.5 V can result in power savings of
about 25 percent. There is virtually no performance penalty when
operating at lower voltage.
When an output is enabled and programmed to 16 mA, an additional 4 mA will flow in the predriver section. This will dissipate
10 mW at 2.5 V or 13.2 mW at 3.3 V for an individual output.
A second measure is to disable outputs when they are not being
used. This can be done on a static basis if the output is not used,
or on a dynamic basis if the output does not have a constant
stream of traffic.
For all 34 outputs enabled and programmed to 16 mA, the
predriver power will be 340 mW at 2.5 V or 449 mW at 3.3 V.
Since the majority of the power dissipated is in the output stage,
some of its flexibility can be used to lower the power consumption.
–20–
REV. A
AD8152
First, the output current can be programmed to the smallest amount
required to maintain BER performance. If an output circuit
always has a short length and the receiver has good sensitivity,
then a lower output current can be used.
ALL TOP-MOUNT SMAs SIT ON PCB TOP LEVEL
SMA CENTER PIN
MICROSTRIP
It is also possible to lower the voltage on VTTO to lower the
power dissipation. The amount that VTTO can be lowered is
dependent on the lowest of all the output’s VOL. This will be
determined by the output that is operating at the highest programmed output current since VOL = VTTO – (IOUT ¥ 25 W).
DRILL HOLES
(7 EACH)
TOP VIEW OF TOP LEVEL TRACE
The AD8152 evaluation board was designed to allow the user to
analyze signal integrity in many configurations, as controlled by
a standard PC.
The FR4 board comes equipped with a full complement of
136 SMA connectors to support the complete 34 ⫻ 34 matrix of
points. Each differential pair of microstrip is connected to either
top mount or side-launch SMA connectors. The mounting area of
the short center pin top-mount SMA connectors are drilled (seven
holes) and stubbed for greatly improved performance. In the
area surrounding SMA top-mount center pin and drill holes, all
internal planes are relieved or cleared out (see Figure 10 for layout).
0.5mils
BOTTOM VIEW OF BOTTOM LEVEL TRACE
Figure 10. Top-Mount SMA PCB Layout, Two Views
EVALUATION BOARD AND PCB LAYOUT HINTS
DIELECTRIC
THICKNESS
PLANE RELIEF
The FR4 PC board is eight layers with a thickness of 62 mils
(1.57 mm). The two outer most metal layers hold the high speed
microstrip routing lines. The two outer most dielectric layers are
5 mils thick and must be controlled impedance (50 W) layers. These
are the only two layers that require controlled impedance. The
next two inner metal layers are ground (reference) planes for the
microstrip and are the shell for the SMA connectors. The remaining four inner metal layers are for the four AD8152 supply and
digital control signal routing. From top to bottom the four supply
layers are VTTO, VCC, VEE, and VTTI. Because all four supply
PCB metal layers float, positive, negative, and even dual-supply
configurations are possible. The variety of supply configurations
ease the connection of test equipment. The four inner supply
layers also provide an interlayer capacitance, which has better
impedance versus frequency than standard chip capacitors.
COPPER
LAYER
NUMBER
THICKNESS/DESIGNATION
(IN OUNCES)
1.
1.50/ TOP MICROSTRIP WIDTH = 8.0mils
2.
0.50/GND
3.
0.50/VTTO
4.
0.50/VCC
5.
0.50/VEE
6.
0.50/VTTI
7.
0.50/GND
8.
1.50/BOTTOM MICROSTRIP WIDTH = 8.0mils
SILKSCREEN
5.0mils
4.0mils
16.0mils
4.0mils
16.0mils
4.0mils
5.0mils
0.5mils
SILKSCREEN
Figure 11. Evaluation Board Stack-Up
REV. A
–21–
AD8152
Figure 12. Cross-Sectional Layout and Dimensioning (To Scale) of Differential
The variety of supply configurations cause the need for a supply
agile digital control circuitry. This is done by a programmable
logic device (PLD), which provides instructions to the AD8152.
The PLD supply is typically tied with jumpers across the AD8152’s
VCC and VEE supplies (Jumpers J3 and J4). The PLD is addressed
from the PC by way of digital isolators. These couplers isolate
PC levels from the PLD and allow for any level shifting. If
desired, the user can drive the PLD supply separately as long as
the VEE of the AD8152 and the PLD are tied together (remove
Jumper J3 and leave J4 installed). This allows one to measure
the AD8152 only supply current, for example.
During the layout of the differential microstrip, a software tool
snaps the distance between the two traces to be a constant. If
the distance is not kept constant, impedance variations will
result. These fluctuations can be measured by time domain
reflectometry (TDR).
EXTRA ADDED INDUCTANCE
Board Construction or Stack-Up
Figure 11 is a picture of AD8152 evaluation board stack-up from
top to bottom. The layer stack-up has been made symmetrical
to avoid board warpage during manufacture. The microstrip
layout and dimensions are shown in Figure 12. The microstrip
trace width was chosen to be 8 mils. This allows relative ease in
routing through the BGA rows that are 50 mils (1.27 mm) apart.
The outer two out of four rows of high speed signals are routed on
top of the PCB, while the inner two rows are via holed to the
board’s opposite side and then routed outward. Wider microstrip
is desirable for reducing eye height loss versus long traces; however, the routing will be more difficult as the AD8152 is approached.
The wide microstrip would have to be necked down in width in
order to be routed into the BGA. The necking will increase trace
impedance and therefore induce more signal reflection problems.
BGA CORNER OUTLINE
VIA HOLE
(GRAY)
CHIP CAPACITOR
(805) SIZE
MICROSTRIP TRACES
Figure 13. BGA Corner Capacitor Layout
Figure 14. Poor Capacitor Layout
Bypass Capacitor Layout
The AD8152 8-layer PCB takes advantage of buried interlayer
capacitance. The VEE to VCC planes are placed in the very middle
of the board to make the highest value capacitor. The 4 mil
(0.102 mm) dielectric spacing between VCC/VEE yields 26 nF
of capacitance. Each AD8152 supply pin is directly connected to
its supply plane through a via hole beneath the BGA ball. The
via hole size for a BGA supply pin is slightly bigger than a signal
via. This is to reduce the inductance of the connection, and it
also happens to be a compact layout.
For the chip capacitors, the via holes are placed directly in the
middle of the mounting area and made as large as possible, i.e.,
greater than or equal to 35 mils (0.89 mm). This is to minimize
inductance as much as possible. By minimizing inductance, the
performance of the capacitor or impedance versus frequency
response is not greatly diminished. Note that chip capacitors
will work up to only about 300 MHz.
Figure 14 is an example of a bypass capacitor layout that should
be avoided in any high speed printed circuit board. This layout
connects the chip capacitor mounting pads to small via holes
through a skinny PCB trace. This amounts to four extra inductors
added to the capacitor, two largely from the skinny surface traces
and two from small via holes. Inductance is also variable with
copper thickness and attachment method to power plane. Thermal
relief for soldering purposes also adds unwanted inductance and
should be avoided.
–22–
REV. A
AD8152
This would require VTTI to be attached to ground, causing
excessive power to be dissipated in the internal 50 W input
termination resistors. Secondly, when the AD8152 output tries
to drive its own input with VTTI = 0 V and VTTO = 2.5 V, the
input will pull the output stage levels down enough to shut off
any signal toggling.
VCC
VTTO
AD8152
P
ECL
DRIVER
All ac coupling shown is actually done with a set of bias tees. If
desired, the bias tee can be used to monitor average dc voltage
levels at an input or output (depending on direction installed),
and it can also serve to change input dc levels. Make sure the
bias tees used in the setup have enough low frequency bandwidth
to pass long patterns and keep edge rates intact. The longer the
pattern, the more low frequency bandwidth is needed.
P
IN
OUT
N
TO 50⍀
SCOPE
INPUTS
N
If ac coupling is desired on a user board, 0402 or 0603 sized
capacitors can be installed on microstrip lines. The biggest 0402
size, XR7 type usable is 0.01 mF, which will work fine for short
patterns (PRBS 27–1) and data rates down to 1.0 Gbps. For
long patterns a 0603 sized, XR7 type, 0.1 mF should be used. To
decrease capacitive loading from the mounting area, clear out
planes underneath the coupling capacitor.
VEE = –2.5V
VTTI = –2V
Figure 15. Evaluation Board ECL Driver Test Setup
Connections for Testing
The AD8152 evaluation board can be used under a variety of positive or negative supply configurations. Negative supply configurations,
as shown in Figure 15, allow the easiest hookup to test equipment because inputs and outputs can be direct coupled. In a real
world application however, the negative supply configuration would
be difficult because control logic levels must be shifted negative.
In Figure 16, 6 dB attenuators are placed before the AD8152
input ac-coupling or bias tees. This is because many generators
won’t go below 500 mV single-ended. The output pair of 6 dB
attenuators is present to protect the scope inputs and allow for
higher scale voltages per division. The eye diagram is usually
viewed differentially by using a simple P – N math function.
Figure 16 is an example of a loop-through test setup using a positive supply. In this case, the test signal goes through the AD8152
twice. It is possible to loop through multiple times if desired, but
jitter will increase with number of loop-throughs. The first
input from the generator and the last output to a scope must be
ac-coupled. However, an AD8152 output driving its own input can
be direct-coupled. Direct coupling to the first AD8152 input is not
effective since generators usually want to see 50 W to ground.
Cabling used in this setup must be matched. Mismatched cables
cause either a P or N signal to be falsely delayed. This delay can
show up as a change in the crossing point, from 50 percent in the
eye diagram. To accurately check cable matches, a TDR setup
is recommended.
2.5V
VCC
VTTI
VTTO
PATTERN
GENERATOR
DATA OUT
–6dB
P
P
IN01
DATA OUT
HIGH SPEED
SAMPLING
OSCILLOSCOPE
AD8152
–6dB
–6dB
50⍀
OUT01
N
N
P
P
–6dB
50⍀
TRIGGER OUT
OUT02
IN02
N
N
VEE
VCC = VTTI = VTTO = 2.5V, VEE = 0V, I OUT SET = 16mA
RTI (REFERRED TO INPUT) A MPLITUDE = 400mV SINGLE–ENDED,
VIN HI = 2.7V (IN01), PRBS 223 –1, VOH = 2.5V,
VOL = 2.1V,
AC-COUPLED IS FROM BIAS TEES,
PROGRAMMING: IN01 TO OUT02, IN02 TO OUT01.
Figure 16. Positive Supply Loop-Through Test Setup
REV. A
–23–
TRIGGER IN
AD8152
Next, select the desired output from the Output Select box by doubleclicking the appropriate output channel number.
EVALUATION BOARD CONTROL SOFTWARE
The AD8152 evaluation board can be controlled by using a PC
and a custom software program. The hardware interface uses a
PC parallel (or printer) port. A standard printer cable is used to
connect from the PC DB-25 connector to the Centronics-type
connector on the evaluation board. Figure 17 shows an evaluation
board control panel from a PC display.
Finally, the Program button is clicked and the data is immediately
sent to the evaluation board for programming the part to the
selected I/O combination.
A single screen allows control of all the programmable functions
of the AD8152. The programming modes are listed in the Mode
box. Select either I/O Programming or Current Programming by
selecting the appropriate radio button. These will allow either
programming the switch matrix or the output currents one at a time.
An alternative is to use the Broadcast mode. This will either
simultaneously program all of the outputs to one selected input
or program all outputs to the same current.
If an additional output(s) is desired to be programmed to the same
input, double-click the desired output channel number and click
the Program button.
The Programmed Output table indicates which outputs are
programmed to the input that is indicated in the Active Input
Selection window. If it is desired to disable an individual output,
its radio button in the Programmed Output table can be clicked,
and it will change from black to white to indicate that it is not
enabled. Note: It is not possible to program outputs by selecting
their radio buttons.
To observe the set of outputs that are connected to any input,
double-click the desired input channel number from the Input
Select box. The selected channel number will show up in the Active
Input Selection window and the programmed outputs will have a
black dot in their radio button in the Programmed Output table.
To program an output current, select the Current Programming
button in the Mode box. Then double-click the desired output
channel number from the Output Select table. Next double-click
the desired entry for the Output Current. Finally, click the
Program button.
Figure 17. Evaluation Board Control Panel
In the I/O Programming mode (nonbroadcast), the desired input
is selected from the Input Select box by double-clicking on the
appropriate input channel number. This will cause the same
channel to appear in the Active Input Selection indicator window.
If the Broadcast button is selected from the Mode box, all outputs
will be treated the same. If I/O Programming is selected, doubleclick the input channel number from the Input Select table
and click the Program button. This will cause all outputs to be
programmed to the selected output, and all of the buttons will
have a black dot in the Programmed Output table.
For broadcast current programming, double-click the desired
Output Current. Then click the Program button. All of the outputs
will be programmed to the selected output current.
The Reset button will disable all outputs. In addition, all output
currents will be programmed to the nominal value of 16 mA.
–24–
REV. A
AD8152
Figure 18. Evaluation Board Top Side Signals
REV. A
–25–
AD8152
Figure 19. Evaluation Board Bottom Side Signals, View from Top
–26–
REV. A
AD8152
Figure 20. Evaluation Board VCC Layer, View from Top
REV. A
–27–
AD8152
Figure 21. Evaluation Board VEE Layer, View from Top
–28–
REV. A
AD8152
Figure 22. Evaluation Board VTTI Layer, View from Top
REV. A
–29–
AD8152
Figure 23. Evaluation Board VTTO Layer, View from Top
–30–
REV. A
AD8152
OUTLINE DIMENSIONS
256-Ball Grid Array [SBGA]
(BP-256)
Dimensions shown in millimeters
A1 CORNER
27.00 BSC
20
18
19
16
17
14
15
12
13
10
11
8
9
6
7
4
5
2
3
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
1.27
A1
27.00 BSC
24.13 REF
TOP
24.13 REF
BOTTOM
1.27
1.00
0.80
0.70 0.60
0.60
0.50
0.20
COPLANARITY
0.20 MIN
SEATING
PLANE
0.90
0.75
0.60
BALL DIAMETER
SEATING PLANE
0.25 MIN
COMPLIANT TO JEDEC STANDARDS MO-192-BAL-2
REV. A
–31–
1
AD8152
Revision History
Location
Page
1/03—Data Sheet changed from REV. 0 to REV. A.
PRINTED IN U.S.A.
C02984–0–1/03(A)
Edits to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
–32–
REV. A