PRELIMINARY IDT70V659S HIGH-SPEED 3.3V 128K x 36 ASYNCHRONOUS DUAL-PORT STATIC RAM Features ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ True Dual-Port memory cells which allow simultaneous access of the same memory location High-speed access – Commercial: 10/12/15ns (max.) – Industrial: 12/15ns (max.) Dual chip enables allow for depth expansion without external logic IDT70V659 easily expands data bus width to 72 bits or more using the Master/Slave select when cascading more than one device M/S = VIH for BUSY output flag on Master, M/S = VIL for BUSY input on Slave Busy and Interrupt Flags On-chip port arbitration logic Full on-chip hardware support of semaphore signaling between ports Fully asynchronous operation from either port Separate byte controls for multiplexed bus and bus matching compatibility Supports JTAG features compliant to IEEE 1149.1 LVTTL-compatible, single 3.3V (±150mV) power supply for core LVTTL-compatible, selectable 3.3V (±150mV)/2.5V (±100mV) power supply for I/Os and control signals on each port Available in a 208-pin Plastic Quad Flatpack, 208-ball fine pitch Ball Grid Array, and 256-ball Ball Grid Array Industrial temperature range (–40°C to +85°C) is available for selected speeds ◆ ◆ ◆ ◆ ◆ ◆ ◆ Functional Block Diagram BE 3L BE3R BE 2L BE2R BE 1 L BE 1R BE 0L BE 0R R/W L R/WR B E 0 L CE0 L B E 1 L B E 2 L B E 3 L B E 3 R B E 2 R B E 1 R B E 0 R CE0 R CE1R CE1L OE R OE L Dout0-8_L Dout9-17_L Dout18-26_L Dout27-35_L Dout0-8_R Dout9-17_R Dout18-26_R Dout27-35_R 128K x 36 MEMORY ARRAY I/O - I/O 0L 35L A16 L A0 L Di n_L Address Decoder ADDR_L CE 0 L CE1L Di n_R OEL I/O - I/O 0R 35R ARBITRATION INTERRUPT SEMAPHORE LOGIC R/WL A16R Address Decoder ADDR_R A0R CE0 R CE1R OER R/WR BUSYR BUSYL SEML M/S SEMR INTR INTL TDI TDO JTAG NOTES: 1. BUSY is an input as a Slave (M/S=VIL) and an output when it is a Master (M/S=VIH). 2. BUSY and INT are non-tri-state totem-pole outputs (push-pull). TMS TCK TRST 4869 drw 01 JUNE 2001 1 ©2001 Integrated Device Technology, Inc. DSC-4869/3 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges Description The IDT70V659 is a high-speed 128K x 36 Asynchronous Dual-Port Static RAM. The IDT70V659 is designed to be used as a stand-alone 4608K-bit Dual-Port RAM or as a combination MASTER/SLAVE DualPort RAM for 72-bit-or-more word system. Using the IDT MASTER/ SLAVE Dual-Port RAM approach in 72-bit or wider memory system applications results in full-speed, error-free operation without the need for additional discrete logic. This device provides two independent ports with separate control, address, and I/O pins that permit independent, asynchronous access for reads or writes to any location in memory. An automatic power down feature controlled by the chip enables (either CE0 or CE1) permit the on-chip circuitry of each port to enter a very low standby power mode. The 70V659 can support an operating voltage of either 3.3V or 2.5V on one or both ports, controlled by the OPT pins. The power supply for the core of the device (VDD) remains at 3.3V. Pin Configurations(1,2,3,4) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 A A I/O19L I/O18L VSS TDO NC A16L A12L A 8L BE1L VDD SEML INTL A4 L A0L OPTL I/O17L B I/O20R VSS I/O 18R TDI NC A13L A9L BE2L CE0L VSS BUSYL A5L A1L VSS VDDQR I/O16L I/O15R C VDDQL I/O19R VDDQR VDD NC A 14L A10L BE3L CE1L VSS R / WL A 6L A2L VDD I/O16R I/O15L VSS C D I/O22L VSS I/O21L I/O 20L A 15L A11 L A7L BE0L VDD OEL NC A3 L VDD I/O 17R VDDQL I/O14L I/O14R D E I/O23L I/O22R VDDQR I/O 21R I/O 12L I/O13R VSS I/O13L E F VDDQL I/O23R I/O24L VSS VSS I/O12R I/O11L VDDQR F G I/O26L VSS I/O25L I/O 24R I/O9 L V DDQL I/O10L I/O11R G H VDD I/O26R VDDQR I/O25R VDD I/O 9R VSS I/O10R H J VDDQL VDD VSS VSS VSS VDD VSS V DDQR J K I/O28R VSS I/O27R VSS I/O 7R VDDQL I/O8R VSS K L I/O29R I/O28L VDDQR I/O27L I/O 6R I/O 7L VSS I/O8 L L M VDDQL I/O29L I/O 30R V SS VSS I/O 6L I/O5R VDDQR M N I/O31L VSS I/O31R I/O 30L I/O 3R VDDQL I/O4R I/O5L N P I/O32R I/O32L VDDQR I/O 35R R VSS I/O33L I/O34R T I/O33R I/O34L U VSS I/O35L 70V659BF BF-208(5) 208-Ball BGA Top View(6) VSS B TRST A16R A 12R A 8R BE1R V DD SEMR INTR A4R I/O2L I/O 3L VSS I/O 4L P TCK NC A13R A9R BE2R CE0R VSS BUSYR A5R A1R VSS VDDQL I/O1R VDDQR R VDDQL TMS NC A14R A10R BE3R CE1R VSS R/WR A6R A2R VSS I/O 0R VSS I/O2 R T VDD NC A15R A11R A7R BE0R VDD OER M/S A3R A0R VDD OPTR I/O 0L I/O1 L U 4869 tbl 02b NOTES: 1. All VDD pins must be connected to 3.3V power supply. 2. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VIH (3.3V) and 2.5V if OPT pin for that port is set to VIL (0V). 3. All VSS pins must be connected to ground. 4. Package body is approximately 15mm x 15mm x 1.4mm with 0.8mm ball pitch. 5. This package code is used to reference the package diagram. 6. This text does not indicate orientation of the actual part-marking. 2 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 70V659DR DR-208(5) 208-Pin PQFP Top View(6) I/O 16L I/O 16R I/O 15L I/O 15R V SS V DDQL I/O 14L I/O 14R I/O 13L I/O 13R V SS V DDQR I/O 12L I/O 12R I/O 11L I/O 11R V SS V DDQL I/O 10L I/O 10R I/O 9L I/O 9R V SS V DDQR V DD V DD V SS V SS V SS V DDQL I/O 8R I/O 8L I/O 7R I/O 7L V SS V DDQR I/O 6R I/O 6L I/O 5R I/O 5L V SS V DDQL I/O 4R I/O 4L I/O 3R I/O 3L V SS V DDQR I/O 2R I/O 2L I/O 1R I/O 1L 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 I/O 19L I/O 19R I/O 20L I/O 20R V DDQL VSS I/O 21L I/O 21R I/O 22L I/O 22R VDDQR VSS I/O 23L I/O 23R I/O 24L I/O 24R V DDQL VSS I/O 25L I/O 25R I/O 26L I/O 26R VDDQR VSS V DD V DD VSS VSS V DDQL VSS I/O 27R I/O 27L I/O 28R I/O 28L VDDQR VSS I/O 29R I/O 29L I/O 30R I/O 30L V DDQL VSS I/O 31R I/O 31L I/O 32R I/O 32L VDDQR VSS I/O 33R I/O 33L I/O 34R I/O 34L 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 VSS VDDQR I/O18R I/O18L VSS VDD TDI TDO NC NC NC A16L A15L A14L A13L A12L A11L A10L A9L A8L A7L BE3L BE2L BE1L BE0L CE1L CE0L VDD VDD VSS VSS SEML OEL R/WL BUSYL INTL NC A6L A5L A4L A3L A2L A1L A0L VDD VDD VSS OPTL I/O17L I/O17R VDDQR VSS Pin Configurations(1,2,3,4) (con't.) VSS VDDQL I/O35R I/O35L VDD TMS TCK TRST NC NC NC A16R A15R A14R A13R A12R A11R A10R A9R A8R A7R BE3R BE2R BE1R BE0R CE1R CE0R VDD VDD VSS VSS SEMR OER R/WR BUSYR INTR M/S A6R A5R A4R A3R A2R A1R A0R VDD VSS VSS OPTR I/O0L I/O0R VDDQL VSS 4869 drw 02a NOTES: 1. All VDD pins must be connected to 3.3V power supply. 2. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VIH (3.3V) and 2.5V if OPT pin for that port is set to VIL (0V). 3. All VSS pins must be connected to ground. 4. Package body is approximately 28mm x 28mm x 3.5mm. 5. This package code is used to reference the package diagram. 6. This text does not indicate orientation of the actual part-marking. 3 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges Pin Configuration(1,2,3,4) (con't.) 70V659BC BC-256(5) 256-Pin BGA Top View(6) A1 NC B1 I/O18L C1 A2 TDI B2 NC C2 I/O18R I/O19L D1 D2 A3 NC B3 TDO C3 VSS D3 I/O20R I/O19R I/O20L E1 E2 E3 A4 NC B4 NC C4 A16L D4 VDD E4 I/O21R I/O21L I/O22L VDDQL F1 F2 F3 F4 I/O23L I/O22R I/O23R VDDQL G1 G2 G3 G4 I/O24R I/O24L I/O25L VDDQR H1 H2 H3 H4 A5 A6 A14L A11L B5 A15L C5 A13L D5 J2 J3 J4 I/O27L I/O28R I/O27R VDDQL K1 K2 K3 K4 I/O29R I/O29L I/O28L VDDQL L1 L2 L3 L4 I/O30L I/O31R I/O30R VDDQR M1 M2 M3 M4 I/O32R I/O32L I/O31L VDDQR N1 N2 N3 I/O33L I/O34R I/O33R P1 P2 P3 I/O35R I/O34L TMS R1 I/O35L T1 NC R2 NC T2 TCK R3 TRST T3 NC N4 VDD P4 A16R R4 NC T4 NC A12L C6 A10L D6 A8L B7 A9L C7 A7L D7 A8 A9 BE2L B8 CE1L B9 C9 BE1L D8 OEL B10 CE0L R/WL BE3L C8 A10 C10 A11 INTL B11 NC C11 BE0L SEML BUSYL D9 D10 D11 A12 A5L B12 A4L C12 A6L D12 A13 A2L B13 A1L C13 A3L D13 A14 A0L B14 NC C14 A15 A16 NC NC B16 B15 I/O17L NC C16 C15 OPTL I/O17R I/O16L D14 D15 D16 VDDQL VDDQL VDDQR VDDQR VDDQL VDDQL VDDQR VDDQR VDD I/O15R I/O15L I/O16R E5 VDD F5 VDD G5 VSS H5 I/O26L I/O25R I/O26R VDDQR VSS J1 B6 A7 J5 VSS K5 VSS L5 VDD M5 VDD N5 E6 VDD F6 VSS G6 VSS H6 VSS J6 VSS K6 VSS L6 VSS M6 VDD N6 E7 VSS F7 VSS G7 VSS H7 VSS J7 VSS K7 VSS L7 VSS M7 VSS N7 E8 E9 VSS F8 VSS F9 VSS VSS G8 G9 VSS H8 VSS H9 VSS J8 VSS J9 VSS K8 VSS K9 VSS L8 VSS L9 VSS M8 VSS M9 VSS N8 VSS N9 E10 VSS F10 VSS G10 VSS H10 VSS J10 VSS K10 VSS L10 VSS M10 VSS N10 E11 VDD F11 VSS G11 VSS H11 VSS J11 VSS K11 VSS L11 VSS M11 VDD N11 E12 F12 A13R R5 A15R T5 A14R P6 A10R R6 A12R T6 A11R P7 A7R R7 A9R T7 A8R P8 P9 P10 P11 BE1R BE0R SEMR BUSY R R8 R9 R10 BE3R CE0R R/WR T8 T9 BE2R CE1R T10 OER R11 M/S T11 INTR E14 E16 E15 F13 F14 F15 F16 VDD VDDQR I/O12R I/O13R I/O12L G12 VSS H12 VSS J12 VSS K12 VSS L12 VDD M12 VDD N12 VDDQR VDDQR VDDQL VDDQL VDDQR VDDQR VDDQL VDDQL P5 E13 VDD VDDQR I/O13L I/O14L I/O14R P12 A6R R12 A4R T12 A5R G13 G14 G16 G15 VDDQL I/O10L I/O11L I/O11R H13 H14 VDDQL I/O9R J13 J14 H16 H15 IO9L I/O10R J15 J16 VDDQR I/O8R I/O7R K13 K14 VDDQR I/O6R L13 L14 VDDQL I/O5L M13 M14 VDDQL I/O3R N13 VDD P13 A3R R13 A1R T13 A2R N14 I/O2L P14 I/O6L L15 OPTR T14 A0R I/O7L L16 I/O4R I/O5R M16 M15 I/O3L I/O4L N16 N15 I/O1R I/O2R P16 P15 I/O0L I/O0R R14 I/O8L K16 K15 I/O1L R16 R15 NC T15 NC , T16 NC NC 4869 drw 02c NOTES: 1. All VDD pins must be connected to 3.3V power supply. 2. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VIH (3.3V), and 2.5V if OPT pin for that port is set to VIL (0V). 3. All VSS pins must be connected to ground supply. 4. Package body is approximately 17mm x 17mm x 1.4mm, with 1.0mm ball-pitch. 5. This package code is used to reference the package diagram. 6. This text does not indicate orientation of the actual part-marking. 4 , IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges Pin Names Left Port Right Port Names CE0L, CE1L CE0R , CE1R Chip Enables R/WL R/WR Read/Write Enable OEL OER Output Enable A0L - A16L A0R - A16R Address I/O0L - I/O35L I/O0R - I/O35R Data Input/Output SEML SEMR Semaphore Enable INTL INTR Interrupt Flag BUSYL BUSYR Busy Flag BE0L - BE3L BE0R - BE3R Byte Enables (9-bit bytes) VDDQL VDDQR Power (I/O Bus) (3.3V or 2.5V)(1) OPTL OPTR Option for selecting VDDQX(1,2) M/S Master or Slave Select VDD Power (3.3V)(1) VSS Ground (0V) TDI Test Data Input TDO Test Data Output TCK Test Logic Clock (10MHz) TMS Test Mode Select TRST Reset (Initialize TAP Controller) NOTES: 1. VDD, OPTX, and VDDQX must be set to appropriate operating levels prior to applying inputs on I/OX. 2. OPTX selects the operating voltage levels for the I/Os and controls on that port. If OPTX is set to VIH (3.3V), then that port's I/Os and controls will operate at 3.3V levels and VDDQX must be supplied at 3.3V. If OPTX is set to VIL (0V), then that port's I/Os and controls will operate at 2.5V levels and VDDQX must be supplied at 2.5V. The OPT pins are independent of one another—both ports can operate at 3.3V levels, both can operate at 2.5V levels, or either can operate at 3.3V with the other at 2.5V. 4869 tbl 01 5 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges Truth Table IRead/Write and Enable Control(1,2) OE SEM CE0 CE1 BE3 BE2 BE1 BE0 R/W Byte 3 I/O27-35 Byte 2 I/O18-26 Byte 1 I/O9-17 Byte 0 I/O0-8 MODE X H H X X X X X X High-Z High-Z High-Z High-Z Deselected–Power Down X H X L X X X X X High-Z High-Z High-Z High-Z Deselected–Power Down X H L H H H H H X High-Z High-Z High-Z High-Z All Bytes Deselected X H L H H H H L L High-Z High-Z High-Z DIN Write to Byte 0 Only X H L H H H L H L High-Z High-Z DIN High-Z Write to Byte 1 Only X H L H H L H H L High-Z DIN High-Z High-Z Write to Byte 2 Only X H L H L H H H L DIN High-Z High-Z High-Z Write to Byte 3 Only X H L H H H L L L High-Z High-Z DIN DIN Write to Lower 2 Bytes Only X H L H L L H H L DIN DIN High-Z High-Z Write to Upper 2 bytes Only X H L H L L L L L DIN DIN DIN DIN Write to All Bytes L H L H H H H L H High-Z High-Z High-Z DOUT Read Byte 0 Only L H L H H H L H H High-Z High-Z DOUT High-Z Read Byte 1 Only L H L H H L H H H High-Z DOUT High-Z High-Z Read Byte 2 Only L H L H L H H H H DOUT High-Z High-Z High-Z Read Byte 3 Only L H L H H H L L H High-Z High-Z DOUT DOUT Read Lower 2 Bytes Only L H L H L L H H H DOUT DOUT High-Z High-Z Read Upper 2 Bytes Only L H L H L L L L H DOUT DOUT DOUT DOUT H H L H L L L L X High-Z High-Z High-Z High-Z Read All Bytes Outputs Disabled NOTES: 1. "H" = VIH, "L" = VIL, "X" = Don't Care. 2. It is possible to read or write any combination of bytes during a given access. A few representative samples have been illustrated here. 4869 tbl 02 Truth Table II Semaphore Read/Write Control(1) Inputs(1) Outputs CE(2) R/W OE BE3 BE2 BE1 BE0 SEM I/O1-35 I/O0 H H L L L L L L DATAOUT DATAOUT Read Data in Semaphore Flag (3) H ↑ X X X X L L X DATAIN Write I/O0 into Semaphore Flag L ______ ______ L X X X X X X Mode Not Allowed NOTES: 1. There are eight semaphore flags written to I/O0 and read from all the I/Os (I/O0-I/O35). These eight semaphore flags are addressed by A 0-A2. 2. CE = L occurs when CE0 = VIL and CE1 = VIH. 3. Each byte is controlled by the respective BEn. To read data BEn = VIL. 6 486 tbl 03 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Recommended DC Operating Conditions with VDDQ at 2.5V Maximum Operating Temperature and Supply Voltage(1) Ambient Temperature Grade O Commercial Industrial O 0 C to +70 C O O -40 C to +85 C Preliminary Industrial and Commercial Temperature Ranges Symbol Parameter GND VDD VDD Core Supply Voltage 0V 3.3V + 150mV VDDQ I/O Supply Voltage (3) 0V 3.3V + 150mV VSS Ground 4869 tbl 04 NOTE: 1. This is the parameter TA. This is the "instant on" case temperature. (3) Min. Typ. Max. Unit 3.15 3.3 3.45 V 2.4 2.5 2.6 V 0 0 0 VDDQ + 100mV (2) V V V VIH Input High Voltage (Address & Control Inputs) 1.7 ____ VIH Input High Voltage - I/O(3) 1.7 ____ VDDQ + 100mV(2) ____ 0.7 V IL Input Low Voltage -0.5 (1) V 4869 tbl 06 NOTES: 1. VIL > -1.5V for pulse width less than 10 ns. 2. VTERM must not exceed VDDQ + 100mV. 3. To select operation at 2.5V levels on the I/Os and controls of a given port, the OPT pin for that port must be set to VIL (0V), and VDDQX for that port must be supplied as indicated above. Absolute Maximum Ratings(1) Symbol Rating Commercial & Industrial Unit VTERM(2) Terminal Voltage with Respect to GND -0.5 to +4.6 V TBIAS Temperature Under Bias -55 to +125 o C TSTG Storage Temperature -65 to +150 o C DC Output Current IOUT Recommended DC Operating Conditions with VDDQ at 3.3V Symbol 50 mA 4869 tbl 05 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VTERM must not exceed VDD + 150mV for more than 25% of the cycle time or 4ns maximum, and is limited to < 20mA for the period of VTERM > VDD + 150mV. Parameter Min. Typ. Max. Unit VDD Core Supply Voltage 3.15 3.3 3.45 V VDDQ I/O Supply Voltage (3) 3.15 3.3 3.45 V VSS Ground 0 0 0 (2) VDDQ + 150mV V V V VIH Input High Voltage (Address & Control Inputs)(3) 2.0 ____ VIH Input High Voltage - I/O(3) 2.0 ____ VDDQ + 150mV(2) ____ 0.8 VIL Input Low Voltage (1) -0.3 V 4869 tbl 07 NOTES: 1. VIL > -1.5V for pulse width less than 10 ns. 2. VTERM must not exceed V DDQ + 150mV. 3. To select operation at 3.3V levels on the I/Os and controls of a given port, the OPT pin for that port must be set to VIH (3.3V), and VDDQX for that port must be supplied as indicated above. Capacitance(1) (TA = +25°C, F = 1.0MHZ) PQFP ONLY Symbol CIN COUT(3) Parameter Input Capacitance Output Capacitance Conditions(2) Max. Unit VIN = 3dV 8 pF VOUT = 3dV 10.5 pF 4869 tbl 08 NOTES: 1. These parameters are determined by device characterization, but are not production tested. 2. 3dV references the interpolated capacitance when the input and output switch from 0V to 3V or from 3V to 0V. 3. COUT also references CI/O. 7 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (VDD = 3.3V ± 150mV) 70V659S Symbol Parameter Test Conditions (1) Min. Max. Unit 10 µA |ILI| Input Leakage Current VDDQ = Max., VIN = 0V to V DDQ ___ |ILO| Output Leakage Current CE0 = VIH or CE1 = VIL, VOUT = 0V to V DDQ ___ 10 µA VOL (3.3V) Output Low Voltage(2) IOL = +4mA, VDDQ = Min. ___ 0.4 V VOH (3.3V) (2) V VOL (2.5V) VOH (2.5V) IOH = -4mA, VDDQ = Min. 2.4 ___ (2) IOL = +2mA, VDDQ = Min. ___ 0.4 V (2) IOH = -2mA, VDDQ = Min. 2.0 ___ V Output High Voltage Output Low Voltage Output High Voltage 4869 tbl 09 NOTE: 1. At VDD < - 2.0V input leakages are undefined. 2. VDDQ is selectable (3.3V/2.5V) via OPT pins. Refer to p.5 for details. DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range(3) (VDD = 3.3V ± 150mV) 70V659S10 Com'l Only Symbol IDD ISB1 ISB2 ISB3 ISB4 Parameter Test Condition Version 70V659S12 Com'l & Ind 70V659S15 Com'l & Ind Typ. (4) Max. Typ.(4) Max. Typ. (4) Max. Unit mA Dynamic Operating Current (Both Ports Active) CEL and CER= VIL, Outputs Disabled f = fMAX (1) COM'L S 340 500 315 465 300 440 IND S ____ ____ 365 515 350 490 Standby Current (Both Ports - TTL Level Inputs) CEL = CER = VIH f = fMAX (1) COM'L S 115 165 90 125 75 100 IND S ____ ____ 115 150 100 125 Standby Current (One Port - TTL Level Inputs) CE"A" = VIL and CE"B" = VIH(5) Active Port Outputs Disabled, f=fMAX (1) COM'L S 225 340 200 325 175 315 IND S ____ ____ 225 365 200 350 COM'L S 3 15 3 15 3 15 IND S ____ ____ 6 15 6 15 S 220 335 195 320 170 310 S ____ ____ 220 360 195 345 Full Standby Current Both Ports CEL and (Both Ports - CMOS CER > VDD - 0.2V, VIN > VDD - 0.2V or VIN < 0.2V, f = 0(2) Level Inputs) Full Standby Current (One Port - CMOS Level Inputs) CE"A" < 0.2V and CE"B" > VDD - 0.2V(5) COM'L VIN > VDD - 0.2V or V IN < 0.2V, Active IND Port, Outputs Disable d, f = fMAX (1) mA mA mA mA 4869 tbl 10 NOTES: 1. At f = fMAX, address and control lines (except Output Enable) are cycling at the maximum frequency read cycle of 1/tRC, using "AC TEST CONDITIONS" at input levels of GND to 3V. 2. f = 0 means no address or control lines change. Applies only to input at CMOS level standby. 3. Port "A" may be either left or right port. Port "B" is the opposite from port "A". 4. VDD = 3.3V, TA = 25°C for Typ, and are not production tested. IDD DC (f=0) = 120mA (Typ). 5. CEX = VIL means CE0X = VIL and CE1X = VIH CEX = VIH means CE0X = VIH or CE1X = V IL CEX < 0.2V means CE0X < 0.2V and CE1X > VCC - 0.2V CEX > VCC - 0.2V means CE0X > VCC - 0.2V or CE1X - 0.2V "X" represents "L" for left port or "R" for right port. 8 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges AC Test Conditions (VDDQ - 3.3V/2.5V) Input Pulse Levels 2.5V GND to 3.0V / GND to 2.5V Input Rise/Fall Times 2ns Max. Input Timing Reference Levels 1.5V/1.25V Output Reference Levels 1.5V/1.25V Output Load 833Ω DATAOUT Figures 1 and 2 5pF* 770Ω 4869 tbl 11 , 3.3V 590Ω 50Ω 50Ω DATAOUT 1.5V/1.25 10pF (Tester) , DATAOUT 435Ω 5pF* 4869 drw 03 Figure 1. AC Output Test load. 4869 drw 04 Figure 2. Output Test Load (For tCKLZ , tCKHZ, tOLZ, and tOHZ). *Including scope and jig. 10.5pF is the I/O capacitance of this device, and 10pF is the AC Test Load Capacitance. 7 6 5 4 ∆tAA (Typical, ns) 3 2 • 1 • 20.5 • 30 • 50 80 100 200 -1 Capacitance (pF) 4869 drw 05 Figure 3. Typical Output Derating (Lumped Capacitive Load). 9 , , IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges AC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range(5) 70V659S10 Com'l Only Symbol Parameter Min. Max. Read Cycle Time 10 Address Access Time ____ 70V659S12 Com'l & Ind Min. Max. ____ 12 10 ____ 10 ____ 70V659S15 Com'l & Ind Min. Max. Unit ____ 15 ____ ns 12 ____ 15 ns 12 ____ 15 ns READ CYCLE tRC tAA tACE tABE tAOE tOH Chip Enable Access Time (3) ____ Byte Enable Access Time (3) ____ 5 ____ 6 ____ 7 ns Output Enable Access Time ____ 5 ____ 6 ____ 7 ns 3 ____ 3 ____ 3 ____ ns 0 ____ 0 ____ 0 ____ ns Output Hold from Address Change (1,2) Output Low-Z Time tLZ (1,2) tHZ Output High-Z Time tPU Chip Enable to Power Up Time (2) 0 4 0 6 0 8 ns 0 ____ 0 ____ 0 ____ ns tPD Chip Disable to Power Down Time (2) ____ 10 ____ 10 ____ 15 ns tSOP Semaphore Flag Update Pulse (OE or SEM) ____ 4 ____ 6 ____ 8 ns tSAA Semaphore Address Access Time 3 10 3 12 3 20 ns 4869 tbl 12 AC Electrical Characteristics Over the Operating Temperature and Supply Voltage(5) 70V659S10 Com'l Only Symbol Parameter 70V659S12 Com'l & Ind 70V659S15 Com'l & Ind Min. Max. Min. Max. Min. Max. Unit 10 ____ 12 ____ 15 ____ ns 8 ____ 10 ____ 12 ____ ns 8 ____ 10 ____ 12 ____ ns 0 ____ 0 ____ 0 ____ ns 8 ____ 10 ____ 12 ____ ns ns WRITE CYCLE tWC tEW tAW tAS tWP Write Cycle Time Chip Enable to End-of-Write (3) Address Valid to End-of-Write Address Set-up Time (3) Write Pulse Width tWR Write Recovery Time 0 ____ 0 ____ 0 ____ tDW Data Valid to End-of-Write 6 ____ 8 ____ 10 ____ ns tDH Data Hold Time(4) 0 ____ 0 ____ 0 ____ ns ____ 4 ____ 4 ____ 4 ns 0 ____ 0 ____ 0 ____ ns 5 ____ 5 ____ 5 ____ ns 5 ____ 5 ____ 5 ____ ns tWZ (1,2) Write Enable to Output in High-Z tOW Output Active from End-of-Write tSWRD SEM Flag Write to Read Time tSPS SEM Flag Contention Window (1,2,4) 4869 tbl 13 NOTES: 1. Transition is measured 0mV from Low or High-impedance voltage with Output Test Load (Figure 2). 2. This parameter is guaranted by device characterization, but is not production tested. 3. To access RAM, CE= V IL and SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. Either condition must be valid for the entire tEW time. 4. The specification for tDH must be met by the device supplying write data to the RAM under all operating conditions. Although tDH and tOW values will vary over voltage and temperature, the actual tDH will always be smaller than the actual tOW. 5. These values are valid regardless of the power supply level selected for I/O and control signals (3.3V/2.5V). See page 5 for details. 10 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges Waveform of Read Cycles(5) tRC ADDR (4) tAA (4) tACE (6) CE tAOE (4) OE tABE (4) BEn R/W tLZ tOH (1) DATAOUT VALID DATA (4) tHZ (2) BUSYOUT tBDD (3,4) 4869 drw 06 NOTES: 1. Timing depends on which signal is asserted last, OE, CE or BEn. 2. Timing depends on which signal is de-asserted first CE, OE or BEn. 3. tBDD delay is required only in cases where the opposite port is completing a write operation to the same address location. For simultaneous read operations BUSY has no relation to valid output data. 4. Start of valid data depends on which timing becomes effective last tAOE, tACE, tAA or tBDD . 5. SEM = VIH. Timing of Power-Up Power-Down CE tPU tPD ICC 50% 50% ISB . 4869 drw 07 11 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges Timing Waveform of Write Cycle No. 1, R/W Controlled Timing(1,5,8) tWC ADDRESS tHZ (7) OE tAW CE or SEM (9) (9) BEn tAS (6) tWP tWR (3) (2) R/W tWZ (7) tOW (4) DATAOUT (4) tDW tDH DATAIN 4869 drw 08 Timing Waveform of Write Cycle No. 2, CE Controlled Timing(1,5) tWC ADDRESS tAW CE or SEM (9) (6) tAS tWR(3) tEW (2) (9) BEn R/W tDW tDH DATAIN 4869 drw 09 NOTES: 1. R/W or CE or BEn = VIH during all address transitions. 2. A write occurs during the overlap (tEW or tWP) of a CE = VIL and a R/W = VIL for memory array writing cycle. 3. tWR is measured from the earlier of CE or R/W (or SEM or R/W) going HIGH to the end of write cycle. 4. During this period, the I/O pins are in the output state and input signals must not be applied. 5. If the CE or SEM = VIL transition occurs simultaneously with or after the R/W = VIL transition, the outputs remain in the High-impedance state. 6. Timing depends on which enable signal is asserted last, CE or R/W. 7. This parameter is guaranteed by device characterization, but is not production tested. Transition is measured 0mV from steady state with the Output Test Load (Figure 2). 8. If OE = VIL during R/W controlled write cycle, the write pulse width must be the larger of tWP or (tWZ + tDW ) to allow the I/O drivers to turn off and data to be placed on the bus for the required tDW . If OE = VIH during an R/W controlled write cycle, this requirement does not apply and the write pulse can be as short as the specified tWP . 9. To access RAM, CE = VIL and SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. tEW must be met for either condition. 12 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges Timing Waveform of Semaphore Read after Write Timing, Either Side(1) tSAA A0-A2 VALID ADDRESS tAW VALID ADDRESS tWR tACE tEW SEM/BEn(1) tOH tSOP tDW I/O DATA OUT(2) VALID DATAIN VALID tAS tWP tDH R/W tSWRD OE tAOE tSOP Write Cycle Read Cycle 4869 drw 10 NOTES: 1. CE = VIH for the duration of the above timing (both write and read cycle) (Refer to Chip Enable Truth Table). Refer also to Truth Table II for appropriate BE controls. 2. "DATAOUT VALID" represents all I/O's (I/O0 - I/O35 ) equal to the semaphore value. Timing Waveform of Semaphore Write Contention(1,3,4) A0"A"-A2"A" (2) SIDE "A" MATCH R/W"A" SEM"A" tSPS A0"B"-A2"B" (2) SIDE "B" MATCH R/W"B" SEM"B" 4869 drw 11 NOTES: 1. DOR = D OL = VIL, CEL = CER = VIH. Refer to Truth Table II for appropriate BE controls. 2. All timing is the same for left and right ports. Port "A" may be either left or right port. "B" is the opposite from port "A". 3. This parameter is measured from R/W"A" or SEM"A" going HIGH to R/W"B" or SEM"B" going HIGH. 4. If tSPS is not satisfied,the semaphore will fall positively to one side or the other, but there is no guarantee which side will be granted the semaphore flag. 13 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges AC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range 70V659S10 Com'l Only Symbol 70V659S12 Com'l & Ind 70V659S15 Com'l & Ind Unit Parameter Min. Max. Min. Max. Min. Max. BUSY TIMING (M/S=VIH) tBAA BUSY Access Time from Address Match ____ 10 ____ 12 ____ 15 ns tBDA BUSY Disable Time from Address Not Matched ____ 10 ____ 12 ____ 15 ns tBAC BUSY Access Time from Chip Enable Low ____ 10 ____ 12 ____ 15 ns tBDC BUSY Disable Time from Chip Enable High ____ 10 ____ 12 ____ 15 ns tAPS Arbitration Priority Set-up Time (2) 5 ____ 5 ____ 5 ____ ns ____ 10 ____ 12 ____ 15 ns 8 ____ 10 ____ 12 ____ ns (3) tBDD BUSY Disable to Valid Data tWH Write Hold After BUSY (5) BUSY TIMING (M/S=VIL) tWB BUSY Input to Write (4) 0 ____ 0 ____ 0 ____ ns tWH Write Hold After BUSY(5) 8 ____ 10 ____ 12 ____ ns ____ 22 ____ 25 ____ 30 ns ____ 20 ____ 22 ____ 25 ns PORT-TO-PORT DELAY TIMING tWDD tDDD Write Pulse to Data Delay(1) Write Data Valid to Read Data Delay (1) 4869 tbl 14 NOTES: 1. Port-to-port delay through RAM cells from writing port to reading port, refer to "Timing Waveform of Write with Port-to-Port Read and BUSY (M/S = VIH)". 2. To ensure that the earlier of the two ports wins. 3. tBDD is a calculated parameter and is the greater of the Max. spec, tWDD – tWP (actual), or tDDD – tDW (actual). 4. To ensure that the write cycle is inhibited on port "B" during contention on port "A". 5. To ensure that a write cycle is completed on port "B" after contention on port "A". 14 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges Timing Waveform of Write with Port-to-Port Read and BUSY (M/S = VIH)(2,4,5) tWC MATCH ADDR"A" tWP R/W"A" tDW tDH VALID DATAIN "A" (1) tAPS MATCH ADDR"B" tBAA tBDA tBDD BUSY"B" tWDD DATAOUT "B" VALID tDDD (3) NOTES: 1. To ensure that the earlier of the two ports wins. tAPS is ignored for M/S = VIL (SLAVE). 2. CEL = CER = VIL. 3. OE = VIL for the reading port. 4. If M/S = VIL (slave), BUSY is an input. Then for this example BUSY"A" = VIH and BUSY"B" input is shown above. 5. All timing is the same for left and right ports. Port "A" may be either the left or right port. Port "B" is the port opposite from port "A". Timing Waveform of Write with BUSY (M/S = VIL) tWP R/W"A" tWB(3) BUSY"B" tWH (1) R/W"B" (2) 4869 drw 13 NOTES: 1. tWH must be met for both BUSY input (SLAVE) and output (MASTER). 2. BUSY is asserted on port "B" blocking R/W"B" , until BUSY"B" goes HIGH. 3. tWB is only for the 'slave' version. 15 . 4869 drw 12 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges Waveform of BUSY Arbitration Controlled by CE Timing (M/S = VIH)(1) ADDR"A" and "B" ADDRESSES MATCH CE"A" tAPS (2) CE"B" tBAC tBDC BUSY"B" 4869 drw 14 Waveform of BUSY Arbitration Cycle Controlled by Address Match Timing (M/S = VIH)(1) ADDR"A" ADDRESS "N" tAPS (2) ADDR"B" MATCHING ADDRESS "N" tBAA tBDA BUSY"B" 4869 drw 15 NOTES: 1. All timing is the same for left and right ports. Port “A” may be either the left or right port. Port “B” is the port opposite from port “A”. 2. If tAPS is not satisfied, the BUSY signal will be asserted on one side or another but there is no guarantee on which side BUSY will be asserted. AC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range 70V659S10 Com'l Only Symbol Parameter 70V659S12 Com'l & Ind 70V659S15 Com'l & Ind Min. Max. Min. Max. Min. Max. Unit 0 ____ 0 ____ 0 ____ ns 0 ____ 0 ____ 0 ____ ns ns INTERRUPT TIMING tAS Address Set-up Time tWR Write Recovery Time tINS Interrupt Set Time ____ 10 ____ 12 ____ 15 tINR Interrupt Reset Time ____ 10 ____ 12 ____ 15 ns 4869 tbl 15 16 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges Waveform of Interrupt Timing(1) tWC INTERRUPT SET ADDRESS ADDR"A" (2) tWR (4) tAS(3) CE"A" R/W"A" tINS (3) INT"B" 4869 drw 16 tRC ADDR"B" INTERRUPT CLEAR ADDRESS tAS (2) (3) CE"B" OE"B" tINR (3) INT"B" 4869 drw 17 NOTES: 1. All timing is the same for left and right ports. Port “A” may be either the left or right port. Port “B” is the port opposite from port “A”. 2. Refer to Interrupt Truth Table. 3. Timing depends on which enable signal (CE or R/W) is asserted last. 4. Timing depends on which enable signal (CE or R/W) is de-asserted first. Truth Table III Interrupt Flag(1,4) Left Port R/WL CEL L L X X X X X L Right Port OEL A16L-A0L X 1FFFF X X L INTL R/WR CER OER A16R-A0R INTR X X X X X L(2) (3) Function Set Right INTR Flag X X X L L 1FFFF H Reset Right INTR Flag X (3) L L X 1FFFE X Set Left INTL Flag (2) X X X X X Reset Left INTL Flag 1FFFE L H 4869 tbl 16 NOTES: 1. Assumes BUSYL = BUSYR =VIH. 2. If BUSYL = VIL, then no change. 3. If BUSYR = VIL, then no change. 4. INTL and INTR must be initialized at power-up. 17 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges Truth Table IV Address BUSY Arbitration Inputs Outputs CEL CER AOL-A16L AOR-A16R BUSYL(1) BUSYR(1) Function X X NO MATCH H H Normal H X MATCH H H Normal X H MATCH H H Normal L L MATCH (2) (2) Write Inhibit(3) 4869 tbl 17 NOTES: 1. Pins BUSYL and BUSYR are both outputs when the part is configured as a master. Both are inputs when configured as a slave. BUSY outputs on the IDT70V659 are push-pull, not open drain outputs. On slaves the BUSY input internally inhibits writes. 2. "L" if the inputs to the opposite port were stable prior to the address and enable inputs of this port. "H" if the inputs to the opposite port became stable after the address and enable inputs of this port. If tAPS is not met, either BUSYL or BUSY R = LOW will result. BUSYL and BUSYR outputs can not be LOW simultaneously. 3. Writes to the left port are internally ignored when BUSYL outputs are driving LOW regardless of actual logic level on the pin. Writes to the right port are internally ignored when BUSYR outputs are driving LOW regardless of actual logic level on the pin. Truth Table V Example of Semaphore Procurement Sequence(1,2,3) Functions D0 - D35 Left D0 - D35 Right Status No Action 1 1 Semaphore free Left Port Writes "0" to Semaphore 0 1 Left port has semaphore token Right Port Writes "0" to Semaphore 0 1 No change. Right side has no write access to semaphore Left Port Writes "1" to Semaphore 1 0 Right port obtains semaphore token Left Port Writes "0" to Semaphore 1 0 No change. Left port has no write access to semaphore Right Port Writes "1" to Semaphore 0 1 Left port obtains semaphore token Left Port Writes "1" to Semaphore 1 1 Semaphore free Right Port Writes "0" to Semaphore 1 0 Right port has semaphore token Right Port Writes "1" to Semaphore 1 1 Semaphore free Left Port Writes "0" to Semaphore 0 1 Left port has semaphore token Left Port Writes "1" to Semaphore 1 1 Semaphore free NOTES: 1. This table denotes a sequence of events for only one of the eight semaphores on the IDT70V659. 2. There are eight semaphore flags written to via I/O0 and read from all I/O's (I/O0-I/O35 ). These eight semaphores are addressed by A0 - A2. 3. CE = VIH, SEM = V IL to access the semaphores. Refer to the Semaphore Read/Write Control Truth Table. Functional Description The IDT70V659 provides two ports with separate control, address and I/O pins that permit independent access for reads or writes to any location in memory. The IDT70V659 has an automatic power down feature controlled by CE. The CE0 and CE1 control the on-chip power down circuitry that permits the respective port to go into a standby mode when not selected (CE = HIGH). When a port is enabled, access to the entire memory array is permitted. Interrupts If the user chooses the interrupt function, a memory location (mail box or message center) is assigned to each port. The left port interrupt flag (INTL) is asserted when the right port writes to memory location 18 4869 tbl 18 1FFFE (HEX), where a write is defined as CER = R/WR = VIL per the Truth Table. The left port clears the interrupt through access of address location 1FFFE when CEL = OEL = VIL, R/W is a "don't care". Likewise, the right port interrupt flag (INTR) is asserted when the left port writes to memory location 1FFFF (HEX) and to clear the interrupt flag (INTR), the right port must read the memory location 1FFFF. The message (36 bits) at 1FFFE or 1FFFF is user-defined since it is an addressable SRAM location. If the interrupt function is not used, address locations 1FFFE and 1FFFF are not used as mail boxes, but as part of the random access memory. Refer to Truth Table III for the interrupt operation. IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Busy Logic address signals only. It ignores whether an access is a read or write. In a master/slave array, both address and chip enable must be valid long enough for a BUSY flag to be output from the master before the actual write pulse can be initiated with the R/W signal. Failure to observe this timing can result in a glitched internal write inhibit signal and corrupted data in the slave. Busy Logic provides a hardware indication that both ports of the RAM have accessed the same location at the same time. It also allows one of the two accesses to proceed and signals the other side that the RAM is “Busy”. The BUSY pin can then be used to stall the access until the operation on the other side is completed. If a write operation has been attempted from the side that receives a BUSY indication, the write signal is gated internally to prevent the write from proceeding. The use of BUSY logic is not required or desirable for all applications. In some cases it may be useful to logically OR the BUSY outputs together and use any BUSY indication as an interrupt source to flag the event of an illegal or illogical operation. If the write inhibit function of BUSY logic is not desirable, the BUSY logic can be disabled by placing the part in slave mode with the M/S pin. Once in slave mode the BUSY pin operates solely as a write inhibit input pin. Normal operation can be programmed by tying the BUSY pins HIGH. If desired, unintended write operations can be prevented to a port by tying the BUSY pin for that port LOW. The BUSY outputs on the IDT70V659 RAM in master mode, are push-pull type outputs and do not require pull up resistors to operate. If these RAMs are being expanded in depth, then the BUSY indication for the resulting array requires the use of an external AND gate. Semaphores A17 CE0 MASTER Dual Port RAM BUSYL BUSYR CE0 SLAVE Dual Port RAM BUSYL BUSYR CE1 MASTER Dual Port RAM CE1 SLAVE Dual Port RAM BUSYL BUSYL BUSYR BUSYR 4869 drw 18 Preliminary Industrial and Commercial Temperature Ranges . Figure 3. Busy and chip enable routing for both width and depth expansion with IDT70V659 RAMs. Width Expansion with Busy Logic Master/Slave Arrays When expanding an IDT70V659 RAM array in width while using BUSY logic, one master part is used to decide which side of the RAMs array will receive a BUSY indication, and to output that indication. Any number of slaves to be addressed in the same address range as the master use the BUSY signal as a write inhibit signal. Thus on the IDT70V659 RAM the BUSY pin is an output if the part is used as a master (M/S pin = VIH), and the BUSY pin is an input if the part used as a slave (M/S pin = VIL) as shown in Figure 3. If two or more master parts were used when expanding in width, a split decision could result with one master indicating BUSY on one side of the array and another master indicating BUSY on one other side of the array. This would inhibit the write operations from one port for part of a word and inhibit the write operations from the other port for the other part of the word. The BUSY arbitration on a master is based on the chip enable and The IDT70V659 is an extremely fast Dual-Port 128K x 36 CMOS Static RAM with an additional 8 address locations dedicated to binary semaphore flags. These flags allow either processor on the left or right side of the Dual-Port RAM to claim a privilege over the other processor for functions defined by the system designer’s software. As an example, the semaphore can be used by one processor to inhibit the other from accessing a portion of the Dual-Port RAM or any other shared resource. The Dual-Port RAM features a fast access time, with both ports being completely independent of each other. This means that the activity on the left port in no way slows the access time of the right port. Both ports are identical in function to standard CMOS Static RAM and can be read from or written to at the same time with the only possible conflict arising from the simultaneous writing of, or a simultaneous READ/WRITE of, a non-semaphore location. Semaphores are protected against such ambiguous situations and may be used by the system program to avoid any conflicts in the non-semaphore portion of the Dual-Port RAM. These devices have an automatic power-down feature controlled by CE, the Dual-Port RAM enable, and SEM, the semaphore enable. The CE and SEM pins control on-chip power down circuitry that permits the respective port to go into standby mode when not selected. Systems which can best use the IDT70V659 contain multiple processors or controllers and are typically very high-speed systems which are software controlled or software intensive. These systems can benefit from a performance increase offered by the IDT70V659s hardware semaphores, which provide a lockout mechanism without requiring complex programming. Software handshaking between processors offers the maximum in system flexibility by permitting shared resources to be allocated in varying configurations. The IDT70V659 does not use its semaphore flags to control any resources through hardware, thus allowing the system designer total flexibility in system architecture. An advantage of using semaphores rather than the more common methods of hardware arbitration is that wait states are never incurred in either processor. This can prove to be a major advantage in very high-speed systems. How the Semaphore Flags Work The semaphore logic is a set of eight latches which are independent of the Dual-Port RAM. These latches can be used to pass a flag, or token, from one port to the other to indicate that a shared resource is in use. The semaphores provide a hardware assist for a use assignment method called “Token Passing Allocation.” In this method, the state of a semaphore latch is used as a token indicating that a shared resource is in use. If the left processor wants to use this resource, it requests the token by setting the latch. This processor then 19 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM verifies its success in setting the latch by reading it. If it was successful, it proceeds to assume control over the shared resource. If it was not successful in setting the latch, it determines that the right side processor has set the latch first, has the token and is using the shared resource. The left processor can then either repeatedly request that semaphore’s status or remove its request for that semaphore to perform another task and occasionally attempt again to gain control of the token via the set and test sequence. Once the right side has relinquished the token, the left side should succeed in gaining control. The semaphore flags are active LOW. A token is requested by writing a zero into a semaphore latch and is released when the same side writes a one to that latch. The eight semaphore flags reside within the IDT70V659 in a separate memory space from the Dual-Port RAM. This address space is accessed by placing a low input on the SEM pin (which acts as a chip select for the semaphore flags) and using the other control pins (Address, CE, R/W and BEo) as they would be used in accessing a standard Static RAM. Each of the flags has a unique address which can be accessed by either side through address pins A0 – A2. When accessing the semaphores, none of the other address pins has any effect. When writing to a semaphore, only data pin D0 is used. If a low level is written into an unused semaphore location, that flag will be set to a zero on that side and a one on the other side (see Truth Table V). That semaphore can now only be modified by the side showing the zero. When a one is written into the same location from the same side, the flag will be set to a one for both sides (unless a semaphore request from the other side is pending) and then can be written to by both sides. The fact that the side which is able to write a zero into a semaphore subsequently locks out writes from the other side is what makes semaphore flags useful in interprocessor communications. (A thorough discussion on the use of this feature follows shortly.) A zero written into the same location from the other side will be stored in the semaphore request latch for that side until the semaphore is freed by the first side. When a semaphore flag is read, its value is spread into all data bits so that a flag that is a one reads as a one in all data bits and a flag containing a zero reads as all zeros. The read value is latched into one side’s output register when that side's semaphore select (SEM, BEn) and output enable (OE) signals go active. This serves to disallow the semaphore from changing state in the middle of a read cycle due to a write cycle from the other side. Because of this latch, a repeated read of a semaphore in a test loop must cause either signal (SEM or OE) to go inactive or the output will never change. However, during reads BEn functions only as an output for semaphore. It does not have any influence on the semaphore control logic. A sequence WRITE/READ must be used by the semaphore in order to guarantee that no system level contention will occur. A processor requests access to shared resources by attempting to write a zero into a semaphore location. If the semaphore is already in use, the semaphore request latch will contain a zero, yet the semaphore flag will appear as one, a fact which the processor will verify by the subsequent read (see Table V). As an example, assume a processor writes a zero to the left port at a free semaphore location. On a subsequent read, the processor will verify that it has written successfully to that location and will assume control over the resource in 20 Preliminary Industrial and Commercial Temperature Ranges question. Meanwhile, if a processor on the right side attempts to write a zero to the same semaphore flag it will fail, as will be verified by the fact that a one will be read from that semaphore on the right side during subsequent read. Had a sequence of READ/WRITE been used instead, system contention problems could have occurred during the gap between the read and write cycles. It is important to note that a failed semaphore request must be followed by either repeated reads or by writing a one into the same location. The reason for this is easily understood by looking at the simple logic diagram of the semaphore flag in Figure 4. Two semaphore request latches feed into a semaphore flag. Whichever latch is first to present a zero to the semaphore flag will force its side of the semaphore flag LOW and the other side HIGH. This condition will L PORT R PORT SEMAPHORE REQUEST FLIP FLOP D0 WRITE D Q SEMAPHORE REQUEST FLIP FLOP Q D SEMAPHORE READ D0 WRITE SEMAPHORE READ Figure 4. IDT70V659 Semaphore Logic 4869 drw 19 continue until a one is written to the same semaphore request latch. Should the other side’s semaphore request latch have been written to a zero in the meantime, the semaphore flag will flip over to the other side as soon as a one is written into the first side’s request latch. The second side’s flag will now stay LOW until its semaphore request latch is written to a one. From this it is easy to understand that, if a semaphore is requested and the processor which requested it no longer needs the resource, the entire system can hang up until a one is written into that semaphore request latch. The critical case of semaphore timing is when both sides request a single token by attempting to write a zero into it at the same time. The semaphore logic is specially designed to resolve this problem. If simultaneous requests are made, the logic guarantees that only one side receives the token. If one side is earlier than the other in making the request, the first side to make the request will receive the token. If both requests arrive at the same time, the assignment will be arbitrarily made to one port or the other. One caution that should be noted when using semaphores is that semaphores alone do not guarantee that access to a resource is secure. As with any powerful programming technique, if semaphores are misused or misinterpreted, a software error can easily happen. Initialization of the semaphores is not automatic and must be handled via the initialization program at power-up. Since any semaphore request flag which contains a zero must be reset to a one, all semaphores on both sides should have a one written into them at initialization from both sides to assure that they will be free when needed. IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges JTAG Timing Specifications tJF tJCL tJCYC tJR tJCH TCK Device Inputs(1)/ TDI/TMS tJS Device Outputs(2)/ TDO tJDC tJH tJRSR tJCD TRST x 4869 drw 20 tJRST NOTES: 1. Device inputs = All device inputs except TDI, TMS, and TRST. 2. Device outputs = All device outputs except TDO. JTAG AC Electrical Characteristics(1,2,3,4) Symbol Parameter Min. Max. Units tJCYC JTAG Clock Input Period 100 ____ ns 40 ____ ns JTAG Clock Low 40 ____ ns tJR JTAG Clock Rise Time ____ (1) 3 ns tJF JTAG Clock Fall Time ____ 3(1) ns tJRST JTAG Reset 50 ____ ns JTAG Reset Recovery 50 ____ ns tJCD JTAG Data Output ____ 25 ns tJDC JTAG Data Output Hold 0 ____ ns tJS JTAG Setup 15 ____ ns 15 ____ tJCH tJCL tJRSR tJH JTAG Clock HIGH JTAG Hold ns 4869 tbl 19 NOTES: 1. Guaranteed by design. 2. 30pF loading on external output signals. 3. Refer to AC Electrical Test Conditions stated earlier in this document. 4. JTAG operations occur at one speed (10MHz). The base device may run at any speed specified in this datasheet. 21 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges Identification Register Definitions Instruction Field Value Revision Number (31:28) Description 0x0 Reserved for version number IDT Device ID (27:12) 0x303 Defines IDT part number IDT JEDEC ID (11:1) 0x33 Allows unique identification of device vendor as IDT ID Register Indicator Bit (Bit 0) 1 Indicates the presence of an ID register 4869 tbl 20 Scan Register Sizes Register Name Bit Size Instruction (IR) 4 Bypass (BYR) 1 Identification (IDR) Boundary Scan (BSR) 32 Note (3) 4869 tbl 21 System Interface Parameters Instruction Code Description EXTEST 0000 Forces contents of the boundary scan cells onto the device outputs (1) . Places the boundary scan register (BSR) between TDI and TDO. BYPASS 1111 Places the bypass register (BYR) between TDI and TDO. IDCODE 0010 Loads the ID register (IDR) with the vendor ID code and places the register between TDI and TDO. 0100 Places the bypass register (BYR) between TDI and TDO. Forces all device output drivers to a High-Z state. HIGHZ Uses BYR. Forces contents of the boundary scan cells onto the device outputs. Places the bypass register (BYR) between TDI and TDO. CLAMP 0011 SAMPLE/PRELOAD 0001 Places the boundary scan register (BSR) between TDI and TDO. SAMPLE allows data from device inputs (2) and outputs(1) to be captured in the boundary scan cells and shifted serially through TDO. PRELOAD allows data to be input serially into the boundary scan cells via the TDI. All other codes Several combinations are reserved. Do not use codes other than those identified above. RESERVED NOTES: 1. Device outputs = All device outputs except TDO. 2. Device inputs = All device inputs except TDI, TMS, and TRST. 3. The Boundary Scan Descriptive Language (BSDL) file for this device is available on the IDT website (www.idt.com), or by contacting your local IDT sales representative. 22 4869 tbl 22 IDT70V659S High-Speed 3.3V 128K x 36 Asynchronous Dual-Port Static RAM Preliminary Industrial and Commercial Temperature Ranges Ordering Information IDT XXXXX Device Type A 999 A A Power Speed Package Process/ Temperature Range Blank I Commercial (0°C to +70°C) Industrial (-40°C to +85°C) BF DR BC 208-ball fpBGA (BF-208) 208-pin PQFP (DR-208) 256-ball BGA (BC-256) 10 12 15 Commercial Only Commercial & Industrial Commercial & Industrial S Standard Power Speed in nanoseconds 70V659 4608K (128K x 36) Asynchronous Dual-Port RAM 4869 drw 21 Preliminary Datasheet: Definition "PRELIMINARY' datasheets contain descriptions for products that are in early release. Datasheet Document History: 6/2/00: 8/11/00: 6/20/01: Initial Public Offering. Inserted additional BEn information on pages 6,13,20. Increased BUSY TIMING parameters tBDA, tBAC, tBDC and tBDD for all speeds on page 14. Changed maximum value for JTAG AC Electrical Characteristics for tJCD from 20ns to 25ns on page 21. CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com The IDT logo is a registered trademark of Integrated Device Technology, Inc. 23 for Tech Support: 831-754-4613 [email protected]