Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Converter Power Modules: 18-36V & 36-75Vdc Input; 1.0V-5Vdc Output; 4A-6A Output Current RoHS Compliant Features Compliant to RoHS EU Directive 2002/95/EC (-Z versions) Compliant to ROHS EU Directive 2002/95/EC with lead solder exemption (non-Z versions) Delivers up to 6A Output current 5V (4A), 3.3V (5A), 2.5V – 1.0V (6A each) Applications Wireless Networks Distributed power architectures Optical and Access Network Equipment Enterprise Networks Latest generation IC’s (DSP, FPGA, ASIC) and Microprocessor powered applications Options Remote On/Off logic (positive or negative) Surface Mount (-S Suffix) Additional Vout+ pin (-3 Suffix) High efficiency – 89% at 5.0V full load Low Output voltage- supports migration to future IC supply voltages down to 1.0V Low output ripple and noise Small Size and low profile 47.2mm x 29.5mm x 8.5mm (1.86 x 1.16 x 0.335 in) Surface mount or Through hole (TH) Remote On/Off Output overcurrent/Over voltage protection Over temperature protection Single Tightly regulated output Output voltage adjustment trim ±10% Wide operating temperature range (-40°C to 85°C) Meets the voltage insulation requirements for ETSI 300-132-2 and complies with and is Licensed for Basic Insulation rating per EN 60950 CE mark meets 73/23/EEC and 93/68/EEC directives§ UL* 60950-1Recognized, CSA† C22.2 No. 60950-1‡ 03 Certified, and VDE 0805:2001-12 (EN60950-1) Licensed ISO** 9001 and ISO 14001 certified manufacturing facilities Description The HW/HC series power modules are isolated dc-dc converters that operate over a wide input voltage range of 18 to 36 Vdc (HC) or 36 to 75 Vdc (HW) and provide one precisely regulated output. The output is fully isolated from the input, allowing versatile polarity configurations and grounding connections. The modules exhibit high efficiency, e.g. typical efficiency of 87% 3.3V/5A, 86% at 2.5V/6A. Built-in filtering for both input and output minimizes the need for external filtering. These open frame modules are available either in surface-mount (-S) or in through-hole form. * UL is a registered trademark of Underwriters Laboratories, Inc. † CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards ‡ Document No: DS03-017 ver.1.21 PDF No: hw-hc_4-6a.pdf Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit Input Voltage HC VIN -0.3 50 Vdc Continuous HW VIN -0.3 80 Vdc Transient (100ms) HW VIN, trans -0.3 100 Vdc All TA -40 85 °C Storage Temperature All Tstg -55 125 °C I/O Isolation Voltage (100% factory tested) All ⎯ ⎯ 2250 Vdc Operating Ambient Temperature (see Thermal Considerations section) Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Operating Input Voltage Device Symbol Min Typ Max Unit HC VIN 18 24 36 Vdc HW VIN 36 54 75 Vdc Maximum Input Current HC IIN,max 1.75 Adc (VIN=0V to 75V, IO=IO, max) HW IIN,max 0.85 Adc Inrush Transient All 2 1 As Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 12μH source impedance; VIN=0V to 75V, IO= IOmax ; see Figure 9) All 5 mAp-p Input Ripple Rejection (120Hz) All 50 dB EMC, EN55022 It 2 See EMC Considerations section CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part of complex power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fastacting fuse with a maximum rating of 3A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. LINEAGE POWER 2 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Electrical Specifications (continued) Parameter Output Voltage Set-point (VIN=VIN,nom, IO=IO, max, Tref=25°C) Output Voltage Device Symbol Min Typ Max Unit 5V, 3.3V 2.5V, 2.0V, 1.8V, 1.5V VO, set -1.0 ⎯ +1.0 % VO, nom 1.2V, 1.0V VO, set -1.25 ⎯ +1.25 % VO, nom All VO -3.0 ⎯ +3.0 % VO, nom All VO -10.0 +10.0 % VO, nom (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range Selected by external resistor Output Regulation Line (VIN=VIN, min to VIN, max) All ⎯ ⎯ 10 mV Load (IO=IO, min to IO, max) All ⎯ ⎯ 15 mV Temperature (Tref=TA, min to TA, max) All ⎯ ⎯ 1.00 % RMS (5Hz to 20MHz bandwidth) All ⎯ 8 15 mVrms Peak-to-Peak (5Hz to 20MHz bandwidth) All Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max) ⎯ 25 50 mVpk-pk External Capacitance All CO, max ⎯ ⎯ 470 μF Output Current 5V Io 0 4.0 Adc 3.3V Io 0 5.0 Adc 2.5V, 2.0, 1.8V, 1.5V, 1.2V, 1.0V Io 0 6.0 Adc 5V IO, lim ⎯ 6.5 ⎯ Adc Output Current Limit Inception ( Hiccup Mode ) Output Short-Circuit Current (VO≤250mV) ( Hiccup Mode ) LINEAGE POWER 3.3V IO, lim ⎯ 7 ⎯ Adc 2.5V, 2.0V, 1.8V, 1.5V, 1.2V, 1.0V IO, lim ⎯ 8.5 ⎯ Adc 5V IO, s/c ⎯ 2.4 ⎯ A rms 3.3V IO, s/c ⎯ 2.4 ⎯ A rms 2.5V, 2.0V, 1.8V, 1.5V, 1.2V, 1.0V IO, s/c ⎯ 2.8 ⎯ A rms 3 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Electrical Specifications (continued) Parameter Device Symbol Min Typ Max Unit HW 5V η ⎯ 89.0 ⎯ % HW 3.3V η ⎯ 87.0 ⎯ % VIN=VIN, nom, TA=25°C HW 2.5V η ⎯ 86.0 ⎯ % IO=IO, max , VO= VO,set HW 2.0V η ⎯ 82.0 ⎯ % HW 1.8V η ⎯ 82.0 ⎯ % HW 1.5V η ⎯ 80.0 ⎯ % HW 1.2V η ⎯ 77.0 ⎯ % HW 1.0V η ⎯ 75.0 ⎯ % Efficiency Switching Frequency HC 5V η ⎯ 88.0 ⎯ % HC 3.3V η ⎯ 86.0 ⎯ % All HW fsw ⎯ 300 ⎯ kHz All HC fsw ⎯ 380 ⎯ kHz Dynamic Load Response 5V, 3.3V Vpk ⎯ 100 ⎯ mV 2.5V, 2.0V, 1.8V, 1.5V, 1.2V, 1.0V Vpk ⎯ 80 ⎯ mV All ts ⎯ 100 ⎯ μs Peak Deviation All Vpk ⎯ 0.6 2 %Vo, set Settling Time (Vo<10% peak deviation) All ts ⎯ 150 1000 μs (ΔIo/Δt=1A/μs; Vin=Vin,nom; TA=25°C) Load Change from Io= 50% to 75% of Io,max: Peak Deviation Settling Time (Vo<10% peak deviation) Dynamic Line Response (ΔVin / Δt≤0.5V/μs; Vin=Vin,nom; TA=25°C) Isolation Specifications Parameter Symbol Min Typ Max Unit Isolation Capacitance Ciso ⎯ 200 ⎯ pF Isolation Resistance Riso 10 ⎯ ⎯ MΩ General Specifications Parameter Min Calculated MTBF (for HW005A0F1-S in accordance with Lucent RIN 6: IO=80% of IO, max, TA=25°C, airflow=1m/s) Weight LINEAGE POWER Typ Max >4,000,000 ⎯ 13 Unit Hours ⎯ g (oz.) 4 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Device Symbol Min Typ Max Unit All Ion/off ⎯ 0.15 1.0 mA All Von/off 0.0 ⎯ 1.2 V Logic High – (Typ = Open Collector) All Von/off ⎯ 5.8 15 V Logic High maximum allowable leakage current All Ion/off ⎯ ⎯ 10 μA Tdelay ⎯ 100 ⎯ ms Trise ⎯ 40 ⎯ ms 2.5V, 2.0V, 1.8V, 1.5V, 1.2V, 1.0V Tdelay ⎯ 12 ⎯ ms Trise ⎯ 3 ⎯ ms 5V VO, limit ⎯ ⎯ 7.0 V 3.3V ⎯ ⎯ 4.6 V 2.5V ⎯ ⎯ 3.5 V 2.0V ⎯ ⎯ 3.2 V 1.8V ⎯ ⎯ 2.8 V 1.5V ⎯ ⎯ 2.5 V 1.2V ⎯ ⎯ 2.0 V ⎯ ⎯ 1.8 V ⎯ 125 ⎯ °C Remote On/Off Signal Interface (VIN=VIN, min to VIN, max ; open collector or equivalent, Signal referenced to VIN- terminal) Negative Logic: device code suffix “1” Logic Low = module On, Logic High = module Off Positive Logic: No device code suffix required Logic Low = module Off, Logic High = module On Logic Low Specification Remote On/Off Current – Logic Low On/Off Voltage: Logic Low Turn-On Delay and Rise Times (IO=IO, max) Tdelay = Time until VO = 10% of VO,set from either application of Vin with Remote On/Off set to On or operation of Remote On/Off from Off to On with Vin already applied for at least one second. Trise = time for VO to rise from 10% of VO,set to 90% of VO,set. Output Overvoltage Protection # Values are the same for HW and HC codes 5V, 3.3V 1.0V Overtemperature Protection All Tref (See Feature Descriptions) Input Undervoltage Lockout Turn-on Threshold All HW ⎯ 33 36 V Turn-off Threshold All HW 27 30 ⎯ V Turn-on Threshold All HC ⎯ 17 18 V Turn-off Threshold All HC 13.5 15 ⎯ V # More accurate Overvoltage protection can be accomplished externally by means of the remote On/Off pin. LINEAGE POWER 5 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Characteristic Curves The following figures provide typical characteristics for the HW004A0A (5.0V, 4A) at 25ºC. The figures are identical for either positive or negative Remote On/Off logic. 90 5 OUTPUT CURRENT, Io (A) 88 EFFICIENCY, η (%) 86 84 82 V I = 36V V I = 54V V I = 75V 80 78 76 74 72 70 0 1 2 3 4 3.0 m/s (600 ft./min.) 2.0 m/s (400 ft./min.) 1.0 m/s (200 ft./min.) NATURAL CONVECTION 1 0 0 10 20 30 40 50 60 70 80 90 100 AMBIENT TEMPERATURE, TA C Figure 3. Transient Response to Dynamic Load Change from 50% to 75% to 50% of full load. LINEAGE POWER OUTPUT VOLTAGE VO (V) (2V/div) VIN (V) (50V/div) VO (V) (2V/div) VON/OFF(V) (5V/div) IO (A) (1A/div) VO (V) (50mV/div) Figure 5. Typical Start-Up with application of Vin. On/Off VOLTAGE OUTPUT VOLTAGE TIME, t (20ms/div) Figure 2. Typical Output Ripple and Noise. TIME, t (50μs/div) 110 Figure 4. Derating Output Current versus Local Ambient Temperature and Airflow INPUT VOLTAGE VO (V) (20mV/div) OUTPUT VOLTAGE, 2 OUTPUT CURRENT, OUTPUT VOLTAGE TIME, t (1μs/div) 3 O OUTPUT CURRENT, IO (A) Figure 1. Converter Efficiency versus Output Current 4 TIME, t (20ms/div) Figure 6. Typical Start-Up Using Remote On/Off, negative logic version shown. 6 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Characteristic Curves (continued) The following figures provide typical characteristics for the HW005A0F (3.3V, 5A) at 25ºC. The figures are identical for either positive or negative Remote On/Off logic. 90 6 OUTPUT CURRENT, Io (A) 88 EFFICIENCY, η (%) 86 84 82 V I = 36V V I = 54V V I = 75V 80 78 76 74 72 70 0 1 2 3 4 5 Figure 9. Transient Response to Dynamic Load Change from 50% to 75% to 50% of full load. LINEAGE POWER 2 1 0 0 10 20 30 40 50 60 70 80 90 100 110 VO (V) (1V/div) VIN (V) (50V/div) INPUT VOLTAGE, OUTPUT VOLTAGE TIME, t (20ms/div) VO (V) (1V/div) Figure 11. Typical Start-Up with application of Vin. OUTPUT VOLTAGE TIME, t (50μs/div) 3.0 m/s (600 ft./min.) 2.0 m/s (400 ft./min.) 1.0 m/s (200 ft./min.) NATURAL CONVECTION Figure 10. Derating Output Current versus Local Ambient Temperature and Airflow VON/OFF(V) (5V/div) VO (V) (50mV/div) IO (A) (2A/div) OUTPUT CURRENT, OUTPUT VOLTAGE Figure 8. Typical Output Ripple and Noise. 3 AMBIENT TEMPERATURE, TA C On/Off VOLTAGE VO (V) (20mV/div) OUTPUT VOLTAGE, TIME, t (1μs/div) 4 O OUTPUT CURRENT, IO (A) Figure 7. Converter Efficiency versus Output Current 5 TIME, t (20ms/div) Figure 12. Typical Start-Up Using Remote On/Off, negative logic version shown. 7 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Characteristic Curves (continued) The following figures provide typical characteristics for the HW006A0G (2.5V, 6A) at 25ºC. The figures are identical for either positive or negative Remote On/Off logic. 88 7 OUTPUT CURRENT, Io (A) 86 EFFICIENCY, η (%) 84 82 80 78 76 V I = 36V V I = 54V V I = 75V 74 72 70 68 0 1 2 3 4 5 6 LINEAGE POWER 2.0 m/ s (400 f t./ min.) 1.0 m/ s (200 f t./ min.) NATURAL CONVECTION 2 1 0 0 10 20 30 40 50 60 70 80 90 100 110 OUTPUT VOLTAGE VO (V) (1V/div) INPUT VOLTAGE, VIN (V) (50V/div) TIME, t (5ms/div) VO (V) (1V/div) Figure 17. Typical Start-Up with application of Vin. OUTPUT VOLTAGE Figure 15. Transient Response to Dynamic Load Change from 50% to 75% to 50% of full load. 3 Figure 16. Derating Output Current versus Local Ambient Temperature and Airflow. On/Off VOLTAGE, VO (V) (50mV/div) IO (A) (2A/div) OUTPUT CURRENT, OUTPUT VOLTAGE TIME, t (50μs/div) 4 AMBIENT TEMPERATURE, TA C VON/OFF(V) (5V/div) VO (V) (20mV/div) OUTPUT VOLTAGE, TIME, t (1μs/div) Figure 14. Typical Output Ripple and Noise. 5 O OUTPUT CURRENT, IO (A) Figure 13. Converter Efficiency versus Output Current. 6 TIME, t (5ms/div) Figure 18. Typical Start-Up Using Remote On/Off, negative logic version shown. 8 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Characteristic Curves (continued) The following figures provide typical characteristics for the HW006A0D (2.0V, 6A) at 25ºC. The figures are identical for either positive or negative Remote On/Off logic. 88 7 OUTPUT CURRENT, Io (A) 86 EFFICIENCY, η (%) 84 82 80 78 76 V I = 36V V I = 54V V I = 75V 74 72 70 68 0 1 2 3 4 5 6 Figure 15. Transient Response to Dynamic Load Change from 50% to 75% to 50% of full load. LINEAGE POWER 2.0 m/ s (400 f t./ min.) 1.0 m/ s (200 f t./ min.) NATURAL CONVECTION 2 1 0 0 10 20 30 40 50 60 70 80 90 100 110 OUTPUT VOLTAGE VO (V) (1V/div) INPUT VOLTAGE, VIN (V) (50V/div) TIME, t (5ms/div) VO (V) (1V/div) Figure 17. Typical Start-Up with application of Vin. OUTPUT VOLTAGE TIME, t (50μs/div) 3 Figure 16. Derating Output Current versus Local Ambient Temperature and Airflow On/Off VOLTAGE, VO (V) (50mV/div) IO (A) (2A/div) OUTPUT CURRENT, OUTPUT VOLTAGE Figure 14. Typical Output Ripple and Noise. 4 AMBIENT TEMPERATURE, TA C VON/OFF(V) (5V/div) VO (V) (20mV/div) OUTPUT VOLTAGE, TIME, t (1μs/div) 5 O OUTPUT CURRENT, IO (A) Figure 13. Converter Efficiency versus Output Current. 6 TIME, t (5ms/div) Figure 18. Typical Start-Up Using Remote On/Off, negative logic version shown. 9 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Characteristic Curves (continued) The following figures provide typical characteristics for the HW006A0Y (1.8V, 6A) at 25ºC. The figures are identical for either positive or negative Remote On/Off logic. 7 86 OUTPUT CURRENT, Io (A) 84 EFFICIENCY, η (%) 82 80 78 76 74 72 V I = 36V V I = 54V V I = 75V 70 68 66 0 1 2 3 4 5 6 Figure 27. Transient Response to Dynamic Load Change from 50% to 75% to 50% of full load. LINEAGE POWER 2.0 m/s (400 ft./min.) 1.0 m/s (200 ft./min.) NATURAL CONVECTION 2 1 0 0 10 20 30 40 50 60 70 80 90 100 110 VO (V) (500mV/div) VIN (V) (25V/div) INPUT VOLTAGE, OUTPUT VOLTAGE TIME, t (5ms/div) VO (V) (500mV/div) Figure 29. Typical Start-Up with application of Vin. OUTPUT VOLTAGE TIME, t (50μs/div) 3 Figure 28. Derating Output Current versus Local Ambient Temperature and Airflow VON/OFF(V) (5V/div) VO (V) (50mV/div) IO (A) (2A/div) OUTPUT CURRENT, OUTPUT VOLTAGE Figure 26. Typical Output Ripple and Noise. 4 AMBIENT TEMPERATURE, TA C On/Off VOLTAGE, VO (V) (20mV/div) OUTPUT VOLTAGE, TIME, t (1μs/div) 5 O OUTPUT CURRENT, IO (A) Figure 25. Converter Efficiency versus Output Current 6 TIME, t (5ms/div) Figure 30. Typical Start-Up Using Remote On/Off, negative logic version shown. 10 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Characteristic Curves (continued) The following figures provide typical characteristics for the HW006A0M (1.5V, 6A) at 25ºC. The figures are identical for either positive or negative Remote On/Off logic. 86 7 OUTPUT CURRENT, Io (A) 84 EFFICIENCY, η (%) 82 80 78 76 74 72 V I = 36V V I = 54V V I = 75V 70 68 66 0 1 2 3 4 5 6 Figure 33. Transient Response to Dynamic Load Change from 50% to 75% to 50% of full load. LINEAGE POWER 2.0 m/s (400 ft./min.) 1.0 m/s (200 ft./min.) NATURAL CONVECTION 2 1 0 0 10 20 30 40 50 60 70 80 90 100 110 VO (V) (500mV/div) VIN (V) (25V/div) INPUT VOLTAGE, OUTPUT VOLTAGE TIME, t (5ms/div) VO (V) (500mV/div) Figure 35. Typical Start-Up with application of Vin. OUTPUT VOLTAGE TIME, t (50μs/div) 3 Figure 34. Derating Output Current versus Local Ambient Temperature and Airflow On/Off VOLTAGE, VO (V) (50mV/div) IO (A) (2A/div) OUTPUT CURRENT, OUTPUT VOLTAGE Figure 32. Typical Output Ripple and Noise. 4 AMBIENT TEMPERATURE, TA C VON/OFF(V) (5V/div) VO (V) (20mV/div) OUTPUT VOLTAGE, TIME, t (1μs/div) 5 O OUTPUT CURRENT, IO (A) Figure 31. Converter Efficiency versus Output Current. 6 TIME, t (5ms/div) Figure 36. Typical Start-Up Using Remote On/Off, negative logic version shown. 11 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Characteristic Curves (continued) The following figures provide typical characteristics for the HW006A0P (1.2V, 6A) at 25ºC. The figures are identical for either positive or negative Remote On/Off logic. 80 7 OUTPUT CURRENT, Io (A) 78 EFFICIENCY, η (%) 76 74 72 70 V I = 36V V I = 54V V I = 75V 68 66 64 62 60 0 1 2 3 4 5 6 TIME, t (50μs/div) Figure 39. Transient Response to Dynamic Load Change from 50% to 75% to 50% of full load. LINEAGE POWER 3 3.0 m/s (600 ft ./min.) 2.0 m/s (400 ft ./min.) 1.0 m/s (200 ft ./min.) NATURAL CONVECTION 2 1 0 0 10 20 30 40 50 60 70 80 90 100 110 VO (V) (500mV/div) VIN (V) (50V/div) INPUT VOLTAGE, OUTPUT VOLTAGE Figure 40. Derating Output Current versus Local Ambient Temperature and Airflow TIME, t (5ms/div) VO (V) (500mV/div) Figure 41. Typical Start-Up with application of Vin. VON/OFF(V) (5V/div) VO (V) (50mV/div) IO (A) (2A/div) OUTPUT CURRENT, OUTPUT VOLTAGE Figure 38. Typical Output Ripple and Noise. 4 AMBIENT TEMPERATURE, TA C On/Off VOLTAGE, OUTPUT VOLTAGE VO (V) (20mV/div) OUTPUT VOLTAGE, TIME, t (1μs/div) 5 O OUTPUT CURRENT, IO (A) Figure 37. Converter Efficiency versus Output Current. 6 TIME, t (5ms/div) Figure 42. Typical Start-Up Using Remote On/Off, negative logic version shown. 12 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Characteristic Curves (continued) The following figures provide typical characteristics for the HW006A0S1R0 (1.0V, 6A) at 25ºC. The figures are identical for either positive or negative Remote On/Off logic. 80 7 OUTPUT CURRENT, Io (A) 78 EFFICIENCY, η (%) 76 74 72 70 68 VI = 36V VI = 54V VI = 75V 66 64 62 60 0 1 2 3 4 5 6 Figure 45. Transient Response to Dynamic Load Change from 50% to 75% to 50% of full load. LINEAGE POWER 3.0 m/s (600 f t./ min.) 2.0 m/s (400 f t./ min.) 1.0 m/s (200 f t./ min.) NATURAL CONVECTION 2 1 0 0 10 20 30 40 50 60 70 80 90 100 110 VO (V) (500mV/div) VIN (V) (50V/div) INPUT VOLTAGE, OUTPUT VOLTAGE Figure 46. Derating Output Current versus Local Ambient Temperature and Airflow. TIME, t (5ms/div) VO (V) (500mV/div) Figure 47. Typical Start-Up with application of Vin. On/Off VOLTAGE, OUTPUT VOLTAGE VO (V) (50mV/div) IO (A) (2A/div) OUTPUT CURRENT, OUTPUT VOLTAGE TIME, t (50μs/div) 3 AMBIENT TEMPERATURE, TA C VON/OFF(V) (5V/div) VO (V) (20mV/div) OUTPUT VOLTAGE, TIME, t (1μs/div) Figure 44. Typical Output Ripple and Noise. 5 4 O OUTPUT CURRENT, IO (A) Figure 43. Converter Efficiency versus Output Current. 6 TIME, t (5ms/div) Figure 48. Typical Start-Up Using Remote On/Off, negative logic version shown. 13 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Characteristic Curves (continued) The following figures provide typical characteristics for the HC004A0A (5.0V, 4A) at 25ºC. The figures are identical for either positive or negative Remote On/Off logic. EFFICIENCY, η (%) OUTPUT CURRENT, Io (A) 5 Figure 51. Transient Response to Dynamic Load Change from 50% to 75% to 50% of full load. LINEAGE POWER 3.0 m/ s (600 ft ./min.) 2.0 m/ s (400 ft ./min.) 1.0 m/ s (200 ft ./min.) Nat ural Convection 1 0 0 10 20 30 40 50 60 70 80 90 100 110 VO (V) (2V/div) VIN (V) (25V/div) INPUT VOLTAGE, OUTPUT VOLTAGE Figure 52. Derating Output Current versus Local Ambient Temperature and Airflow. TIME, t (20ms/div) VO (V) (2V/div) Figure 53. Typical Start-Up with application of Vin. VON/OFF(V) (5V/div) VO (V) (50mV/div) IO (A) (1A/div) OUTPUT CURRENT, OUTPUT VOLTAGE TIME, t (50μs/div) 2 AMBIENT TEMPERATURE, TA C On/Off VOLTAGE, OUTPUT VOLTAGE VO (V) (20mV/div) OUTPUT VOLTAGE, TIME, t (1μs/div) Figure 50. Typical Output Ripple and Noise. 3 O OUTPUT CURRENT, IO (A) Figure 49. Converter Efficiency versus Output Current. 4 TIME, t (20ms/div) Figure 54. Typical Start-Up Using Remote On/Off, negative logic version shown. 14 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Characteristic Curves (continued) The following figures provide typical characteristics for the HC005A0F (3.3V, 5A) at 25ºC. The figures are identical for either positive or negative Remote On/Off logic. EFFICIENCY, η (%) OUTPUT CURRENT, Io (A) 6 3.0 m/ s (600 ft ./min.) 2.0 m/ s (400 ft ./min.) 1.0 m/ s (200 ft ./min.) Nat ural Convection 2 1 0 0 10 20 30 40 50 60 70 80 90 100 AMBIENT TEMPERATURE, TA C Figure 57. Transient Response to Dynamic Load Change from 50% to 75% to 50% of full load. LINEAGE POWER VO (V) (1V/div) VIN (V) (25V/div) VO (V) (1V/div) VON/OFF(V) (5V/div) IO (A) (2A/div) VO (V) (50mV/div) Figure 59. Typical Start-Up with application of Vin. On/Off VOLTAGE, OUTPUT VOLTAGE TIME, t (20ms/div) Figure 56. Typical Output Ripple and Noise. TIME, t (50μs/div) 110 Figure 58. Derating Output Current versus Local Ambient Temperature and Airflow. INPUT VOLTAGE, OUTPUT VOLTAGE VO (V) (20mV/div) OUTPUT VOLTAGE, 3 OUTPUT CURRENT, OUTPUT VOLTAGE TIME, t (1μs/div) 4 O OUTPUT CURRENT, IO (A) Figure 55. Converter Efficiency versus Output Current. 5 TIME, t (20ms/div) Figure 60. Typical Start-Up Using Remote On/Off, negative logic version shown. 15 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Test Configurations Design Considerations CURRENT PROBE TO OSCILLOSCOPE The power module should be connected to a low ac-impedance source. A highly inductive source impedance can affect the stability of the power module. For the test configuration in Figure 61, a 33μF electrolytic capacitor (ESR<0.7Ω at 100kHz), mounted close to the power module helps ensure the stability of the unit. Consult the factory for further application guidelines. LTEST Vin+ BATTERY 12μH CS 220μF 33μF E.S.R.<0.1Ω @ 20°C 100kHz Vin- NOTE: Measure input reflected ripple current with a simulated source inductance (LTEST) of 12μH. Capacitor CS offsets possible battery impedance. Measure current as shown above. Figure 61. Input Reflected Ripple Current Test Setup. COPPER STRIP VO (+) RESISTIVE LOAD 1uF . 10uF Input Source Impedance SCOPE V O (–) GROUND PLANE NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. Safety Considerations For safety-agency approval of the system in which the power module is used, the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standard, i.e., UL 60950-1-3, CSA C22.2 No. 60950-00, and VDE 0805:2001-12 (IEC60950-1). If the input source is non-SELV (ELV or a hazardous voltage greater than 60 Vdc and less than or equal to 75Vdc), for the module’s output to be considered as meeting the requirements for safety extra-low voltage (SELV), all of the following must be true: The input source is to be provided with reinforced insulation from any other hazardous voltages, including the ac mains. One VIN pin and one VOUT pin are to be grounded, or both the input and output pins are to be kept floating. The input pins of the module are not operator accessible. Another SELV reliability test is conducted on the whole system (combination of supply source and subject module), as required by the safety agencies, to verify that under a single fault, hazardous voltages do not appear at the module’s output. Figure 62. Output Ripple and Noise Test Setup. Rdistribution Rcontact Rcontact Vin+ RLOAD VO VIN Rdistribution Rcontact Rcontact Vin- Rdistribution Vout+ Rdistribution Vout- NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. Figure 63. Output Voltage and Efficiency Test Setup. VO. IO Efficiency η = LINEAGE POWER VIN. IIN x 100 % Note: Do not ground either of the input pins of the module without grounding one of the output pins. This may allow a non-SELV voltage to appear between the output pins and ground. The power module has extra-low voltage (ELV) outputs when all inputs are ELV. For input voltages exceeding –60 Vdc but less than or equal to –75 Vdc, these converters have been evaluated to the applicable requirements of BASIC INSULATION between secondary DC MAINS DISTRIBUTION input (classified as TNV-2 in Europe) and unearthed SELV outputs. "All flammable materials used in the manufacturing of these modules are rated 94V-0 and UL60950 A.2 for reduced thicknesses. The input to these units is to be provided with a maximum 3A fast-acting fuse in the unearthed lead." 16 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current only begin to operate once the input voltage is raised above the undervoltage lockout turn-on threshold, VUV/ON. Feature Description Remote On/Off Two remote on/off options are available. Positive logic turns the module on during a logic high voltage on the ON/OFF pin, and off during a logic low. Negative logic remote On/Off, device code suffix “1”, turns the module off during a logic high and on during a logic low. To maintain compatibility with LW series power modules the Remote On/Off pin is optional for the TH (through hole) version. Standard TH modules have no On/Off pin fitted. TH modules ordered with device code suffix “1” are negative logic with the On/Off pin fitted. Once operating, the module will continue to operate until the input voltage is taken below the undervoltage turn-off threshold, VUV/OFF. Over Voltage Protection The output overvoltage protection consists of circuitry that internally clamps the output voltage. If a more accurate output overvoltage protection scheme is required then this should be implemented externally via use of the remote on/off pin. Over Temperature Protection VIN(+) VO Ion/off ON/OFF Von/off COM VIN(-) Figure 64. Remote On/Off Implementation. To turn the power module on and off, the user must supply a switch (open collector or equivalent) to control the voltage (Von/off) between the ON/OFF terminal and the VIN(-) terminal. Logic low is 0V ≤ Von/off ≤ 1.2V. The maximum Ion/off during a logic low is 1mA, the switch should be maintain a logic low level whilst sinking this current. During a logic high, the typical Von/off generated by the module is 5.8V, and the maximum allowable leakage current at Von/off = 5.8V is 10μA. If not using the remote on/off feature: For positive logic, leave the ON/OFF pin open. For negative logic, short the ON/OFF pin to VIN(-). Overcurrent Protection To provide protection in a fault (output overload) condition, the unit is equipped with internal current-limiting circuitry and can endure current limiting continuously. At the point of current-limit inception, the unit enters hiccup mode. The unit operates normally once the output current is brought back into its specified range. The average output current during hiccup is 10% IO, max. To provide protection in a fault condition, the unit is equipped with a thermal shutdown circuit. The unit will o shutdown if the overtemperature threshold of 125 C is exceeded at the thermal reference point Tref . Once the unit goes into thermal shutdown it will then wait to cool before attempting to restart. Output Voltage Programming Trimming allows the output voltage set point to be increased or decreased, this is accomplished by connecting an external resistor between the TRIM pin and either the VO(+) pin or the VO(-) pin (COM pin) . VIN(+) VO(+) Rtrim-up ON/OFF LOAD VOTRIM Rtrim-down VIN(-) COM Figure 65. Circuit Configuration to Trim Output Voltage. Connecting an external resistor (Rtrim-down) between the TRIM pin and the COM pin decreases the output voltage set point. To maintain set point accuracy, the trim resistor tolerance should be ±0.1%. Input Undervoltage Lockout At input voltages below the input undervoltage lockout limit, the module operation is disabled. The module will LINEAGE POWER 17 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Feature Descriptions (continued) The relationship between the output voltage and the trim resistor value for a Δ% reduction in output voltage is: Rtrim-down = 249.39 kΩ Nominal 5V, 3.3V, 2.5V, 2.0V, 1.8V, & 1.5V modules: 511 Rtrim-down = Δ% - 6.11 kΩ To trim up the output of a nominal 3.3V module (HW005A0F) to 3.63V Δ% = 10 5.11x3.3(100+10) Nominal 1.2V module: Rtrim-up = 346 Rtrim-down = Δ% - 4.46 kΩ 1.225x10 511 - 10 - 6.11 kΩ Rtrim-up =94.2 kΩ Nominal 1.0V module: 390 Rtrim-down = Δ% - 4.90 kΩ Connecting an external resistor (Rtrim-up) between the TRIM pin and the VO(+) pin increases the output voltage set point. To maintain set point accuracy, the trim resistor tolerance should be ±0.5%. The relationship between the output voltage and the trim resistor value for a Δ% increase in output voltage is: Nominal 5V, 3.3V, 2.5V, 2.0V, 1.8V, & 1.5V modules: Rtrim-up = 5.11VO(100+Δ%) 1.225Δ% 511 - Δ% - 6.11 kΩ Nominal 1.2V module: Rtrim-up = 5.11VO(100+Δ%) 1.225Δ% 346 - Δ% - 4.46 kΩ Nominal 1.0V module: Rtrim-up = 5.11VO(100+Δ%) 1.225Δ% 390 - Δ% - 4.90 kΩ (VO refers to the nominal output voltage, i.e. 5.0V for VO on an HW004A0A. Δ% is the required % change in output voltage, i.e. to trim a 5.0V module to 5.10V the Δ% value is 2). Examples: To trim down the output of a nominal 5.0V module (HW004A0A) to 4.90V Δ% = 2 511 Rtrim-down = 2 LINEAGE POWER - 6.11 kΩ 18 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Thermal Considerations Considerations include ambient temperature, airflow, module power dissipation, and the need for increased reliability. A reduction in the operating temperature of the module will result in an increase in reliability. The thermal data presented here is based on physical measurements taken in a wind tunnel. The thermal reference point, Tref used in the specifications is shown in Figure 66. For reliable operation this temperature should not exceed 115 oC. C5 56nF L2 10uH The power modules operate in a variety of thermal environments; however, sufficient cooling should be provided to help ensure reliable operation. C1 0.68uF C2 0.68uF C3 0.68uF Vin+ C4 33uF 100V Vout+ HW005 Vin- Vout- L1 - CMC Pulse P0354 C6 56nF Figure 67. Suggested Configuration for EN55022 Class B. 90 80 70 60 EN 55022 Class B Conducted Average dBuV 50 40 Level (dBµV) 30 20 10 100K 500K 1M 5M 10M 30M Frequency(Hz) Figure 66. Tref Temperature Measurement Location. Please refer to the Application Note “Thermal Characterization Process For Open-Frame BoardMounted Power Modules” for a detailed discussion of thermal aspects including maximum device temperatures. Figure 68. EMC signature using above filter, HW005A0F. For further information on designing for EMC compliance, please refer to the FLTR100V10 data sheet (FDS01-043EPS). Layout Considerations Heat Transfer via Convection Increased airflow over the module enhances the heat transfer via convection. Derating figures showing the maximum output current that can be delivered by each module versus local ambient temperature (TA) for natural convection and up to 3m/s (600 ft./min) are shown in the respective Characteristics Curves section. The HW/HC005 power module series are low profile in order to be used in fine pitch system card architectures. As such, component clearance between the bottom of the power module and the mounting board is limited. Avoid placing copper areas on the outer layer directly underneath the power module. Also avoid placing via interconnects underneath the power module. For additional layout guide-lines, refer to FLTR100V10 data sheet. EMC Considerations The figure 67 shows a suggested configuration to meet the conducted emission limits of EN55022 Class B. LINEAGE POWER 19 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Mechanical Outline for HW/HC Surface-Mount Module Dimensions are in millimeters and (inches). Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated] x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.) 47.2 (1.860) Top View 29.5 (1.162) Side View 2.54 (0.100) min stand-off height 8.50 (0.335) MAX 0.5 (.020) max compliance Bottom View Pin Vout + 2 Vout - 3 10.00 (0.394) Function 1 Standard = No Pin 40.00 (1.576) PIN 3 OPTIONAL 9 1 2 3 26.16 (1.031) Optional = Vout + 9 Trim 11 On/Off 17 Vin - 18 Vin + LINEAGE POWER 18 17 1.65 (0.065) 3.63 (0.143) 11 5.00 (0.197) 35.00 (1.379) 20 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Mechanical Outline for HW/HC Through Hole Module Dimensions are in millimeters and (inches). Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated] x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.) 47.2 (1.860) Top View 29.5 (1.162) Side View * Optional pin lengths shown in Table 2 Device Options 40.00 (1.576) Bottom View Pin Function 1 Vout + 2 Vout - 9 Trim 11 On/Off 17 Vin - 18 Vin + 1 9 26.16 (1.031) 18 17 1.65 (0.065) 3.63 (0.143) LINEAGE POWER 2 11 5.00 (0.197) 35.00 (1.379) 21 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Recommended Pad Layout for Surface Mount and Through Hole Module Dimensions are in millimeters and (inches). Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated] x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.) Pin Function 1 Vout + 2 Vout - 3 Standard = No Pin Optional = Vout + 9 Trim 11 On/Off 17 Vin - 18 Vin + Surface Mount Pad Layout – Component side view Pin Function 1 Vout + 2 Vout - 9 Trim 11 On/Off 17 Vin - 18 Vin + Through-Hole Pad Layout – Component side view LINEAGE POWER 22 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Packaging Details The surface mount versions of the HW005 family are also available in tape & reel (suffix –SR) as an option. Detailed of tape dimensions are shown below. Modules are shipped in quantities of 115 per reel. Tape Dimensions Dimensions are in millimeters and (inches). PICK POINT 4.00 (0.157) 9.02 (0.355) 40.00 (1.575) FEED DIRECTION 34.20 (1.346) 72.00 (2.834) 68.40 (2.692) 66.50 (2.692) TOP COVER TAPE EMBOSSED CARRIER NOTE: CONFORMS TO EAI-481 REV. A STANDARD Reel Dimensions Outside diameter: Inside diameter: Tape Width: LINEAGE POWER 330.2 mm (13.00”) 177.8 mm (7.00”) 72.00 mm (2.834”) 23 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Through-Hole Lead-Free Soldering Information The RoHS-compliant through-hole products use the SAC (Sn/Ag/Cu) Pb-free solder and RoHS-compliant components. They are designed to be processed through single or dual wave soldering machines. The pins have an RoHS-compliant finish that is compatible with both Pb and Pb-free wave soldering processes. A maximum preheat rate of 3°C/s is suggested. The wave preheat process should be such that the temperature of the power module board is kept below 210°C. For Pb solder, the recommended pot temperature is 260°C, while the Pb-free solder pot is 270°C max. Not all RoHS-compliant through-hole products can be processed with paste-through-hole Pb or Pb-free reflow process. If additional information is needed, please consult with your Lineage Power representative for more details. Surface Mount Information Packaging Details The surface mount versions of the HW005 family (suffix –S) are supplied as standard in the plastic tray shown in Figure 69. The tray has external dimensions of 135.1mm (W) x 321.8mm (L) x 12.4mm (H) or 5.319in (W) x 12.669in (L) x 0.489in (H). Surface mount versions of the HW005 family are also available as an option packaged in Tape and Reel. For further information on this please contact your local Lineage Power Technical Sales Representative. Figure 69. Surface Mount Packaging Tray Tray Specification Material Antistatic coated PVC Max surface resistivity Color Capacity Min order quantity 1012Ω/sq Clear 15 power modules 60 pcs (1 box of 4 full trays) Each tray contains a total of 15 power modules. The trays are self-stacking and each shipping box will contain 4 full trays plus one empty hold down tray giving a total number of 60 power modules. Pick and Place The HW005-S series of DC-to-DC power converters use an open-frame construction and are designed for surface mount assembly within a fully automated manufacturing process. The HW005-S series modules are fitted with a Kapton label designed to provide a large flat surface for pick and placing. The label is located covering the Centre of Gravity of the power module. The label meets all the requirements for surface-mount processing, as well as meeting UL safety agency standards. The label will withstand reflow temperatures up to 300°C. The label also carries product information such as product code, date and location of manufacture. LINEAGE POWER 24 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Surface Mount Information (continued) 24.2 damage to the modules, and can adversely affect long-term reliability. The surface mountable modules in the HW005 family use our newest SMT technology called “Column Pin” (CP) connectors. Fig 71 shows the new CP connector before and after reflow soldering onto the end-board assembly. COG 8.0 14.7 12.7 HW005 Board Insulator 9.5 Note: All dimensions in mm. Figure 70. Pick and Place Location. Z Plane Height The ‘Z’ plane height of the pick and place location is 7.50mm nominal with an RSS tolerance of +/-0.25 mm. Nozzle Recommendations The module weight has been kept to a minimum by using open frame construction. Even so, they have a relatively large mass when compared with conventional SMT components. Variables such as nozzle size, tip style, vacuum pressure and placement speed should be considered to optimize this process. The minimum recommended nozzle diameter for reliable operation is 6mm. The maximum nozzle outer diameter, which will safely fit within the allowable component spacing, is 9 mm. Oblong or oval nozzles up to 11 x 9 mm may also be used within the space available. For further information please contact your local Lineage Power Technical Sales Representative. Reflow Soldering Information The HW005 family of power modules is available for either Through-Hole (TH) or Surface Mount (SMT) soldering. These power modules are large mass, low thermal resistance devices and typically heat up slower than other SMT components. It is recommended that the customer review data sheets in order to customize the solder reflow profile for each application board assembly. The following instructions must be observed when SMT soldering these units. Failure to observe these instructions may result in the failure of or cause LINEAGE POWER Solder Ball End assembly PCB Figure 71. Column Pin Connector Before and After Reflow Soldering. The CP is constructed from a solid copper pin with an integral solder ball attached, which is composed of tin/lead (Sn/Pb) solder. The CP connector design is able to compensate for large amounts of co-planarity and still ensure a reliable SMT solder joint. Typically, the eutectic solder melts at 183oC, wets the land, and subsequently wicks the device connection. Sufficient time must be allowed to fuse the plating on the connection to ensure a reliable solder joint. There are several types of SMT reflow technologies currently used in the industry. These surface mount power modules can be reliably soldered using natural forced convection, IR (radiant infrared), or a combination of convection/IR. For reliable soldering the solder reflow profile should be established by accurately measuring the modules CP connector temperatures. 300 P eak Temp 235oC 250 REFLOW TEMP (°C) 19.0 200 Co o ling zo ne 1-4oCs -1 Heat zo ne max 4oCs -1 150 100 50 So ak zo ne 30-240s Tlim above 205oC P reheat zo ne max 4oCs -1 0 REFLOW TIME (S) Figure 72. Recommended Reflow Profile 25 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Surface Mount Information (continued) 240 MAX TEMP SOLDER (°C) 235 The shelf life for dry packed SMT packages will be a minimum of 12 months from the bag seal date, when stored at the following conditions: < 40° C, < 90% relative humidity. Post Solder Cleaning and Drying Considerations 230 225 220 215 210 205 200 0 10 20 30 40 50 60 TIME LIMIT (S) Post solder cleaning is usually the final circuit-board assembly process prior to electrical board testing. The result of inadequate cleaning and drying can affect both the reliability of a power module and the testability of the finished circuit-board assembly. For guidance on appropriate soldering, cleaning and drying procedures, refer to Lineage Power Board Mounted Power Modules: Soldering and Cleaning Application Note (AP01-056EPS). 300 Figure 73. Time Limit Curve Above 205oC Reflow . Per J-STD-020 Rev. C Peak Temp 260°C Lead Free Soldering The –Z version SMT modules of the HW/HC series are lead-free (Pb-free) and RoHS compliant and are compatible in a Pb-free soldering process. Failure to observe the instructions below may result in the failure of or cause damage to the modules and can adversely affect long-term reliability. Reflow Temp (°C) 250 200 * Min. Time Above 235°C 15 Seconds Cooling Zone 150 Heating Zone 1°C/Second *Time Above 217°C 60 Seconds 100 50 0 Pb-free Reflow Profile Power Systems will comply with J-STD-020 Rev. C (Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices) for both Pb-free solder profiles and MSL classification procedures. This standard provides a recommended forced-air-convection reflow profile based on the volume and thickness of the package (table 4-2). The suggested Pb-free solder paste is Sn/Ag/Cu (SAC). The recommended linear reflow profile using Sn/Ag/Cu solder is shown in Figure. 74. MSL Rating Reflow Time (Seconds) Figure 74. Recommended linear reflow profile using Sn/Ag/Cu solder. Solder Ball and Cleanliness Requirements The open frame (no case or potting) power module will meet the solder ball requirements per J-STD-001B. These requirements state that solder balls must neither be loose nor violate the power module minimum electrical spacing. The cleanliness designator of the open frame power module is C00 (per J specification). The HW/HC series SMT modules have a MSL rating of 1. Storage and Handling The recommended storage environment and handling procedures for moisture-sensitive surface mount packages is detailed in J-STD-033 Rev. A (Handling, Packing, Shipping and Use of Moisture/Reflow Sensitive Surface Mount Devices). Moisture barrier bags (MBB) with desiccant are required for MSL ratings of 2 or greater. These sealed packages should not be broken until time of use. Once the original package is broken, the floor life of the product at conditions of ≤ 30°C and 60% relative humidity varies according to the MSL rating (see J-STD-033A). LINEAGE POWER 26 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Ordering Information Please contact your Lineage Power Sales Representative for pricing, availability and optional features. Table 1. Device Codes Product codes Input Voltage Output Voltage Output Current HW004A0A-S HW004A0A-SZ HW004A0A1 HW004A0A1-S HW004A0A1Z HW004A0A1-SB HW004A0A1-SZ HW005A0F-S HW005A0F-SZ HW005A0F-SR39* HW005A0F1 HW005A0F1Z HW005A0F1-S HW005A0F1-SZ HW005A0F1-SRZ HW005A0F1-S65* HW005A0F1-S65Z* HW006A0G1-SZ HW006A0D1-S HW006A0D1-SZ HW006A0Y1-S HW006A0Y1-SZ HW006A0P1-SZ HC004A0A1-S HC004A0A1-SZ HC005A0F1-S HC005A0F1-SZ 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 48 Vdc 24 Vdc 24 Vdc 24 Vdc 24 Vdc 5.0V 5.0V 5.0V 5.0V 5.0V 5.0V 5.0V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 2.5V 2.0V 2.0V 1.8V 1.8V 1.2V 5.0V 5.0V 3.3V 3.3V 4A 4A 4A 4A 4A 4A 4A 5A 5A 5A 5A 5A 5A 5A 5A 5A 5A 6A 6A 6A 6A 6A 6A 4A 4A 5A 5A LINEAGE POWER Remote On/Off Logic Positive Positive Negative Negative Negative Negative Negative Positive Positive Positive Negative Negative Negative Negative Negative Negative Negative Negative Negative Negative Negative Negative Negative Negative Negative Negative Negative Connector Type SMT SMT Through-Hole SMT Through-Hole SMT SMT SMT SMT SMT (tape & reel) Through-Hole Through-Hole SMT SMT SMT (tape&reel) SMT SMT SMT SMT SMT SMT SMT SMT SMT SMT SMT SMT Comcodes 108968272 109100245 108965476 108960634 CC109102002 108980525 109100237 108968678 109100261 108986951 108967779 CC109107125 108960667 108995197 109100253 108987512 108995206 109100311 108969676 109100303 108960782 109100344 109100336 108960642 108996113 108960659 108996121 27 Data Sheet May 16, 2008 HW/HC004/005/006 Series DC-DC Power Module: 18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current Table 2. Device Options Option Suffix Negative remote on/off logic 1 With additional Vout+ pin3 3 Short Pins: 3.68 mm ± 0.25 mm (0.145 in ±0.010 in) 6 Short Pins: 2.79 mm ± 0.25 mm (0.110 in ±0.010 in) 8 Customer specific -39 Customer specific -65 Tape & Reel -R Surface mount connections -S RoHS Compliant -Z * Please contact Lineage Power for availability of these options, samples, minimum order quantity and lead times Asia-Pacific Headquarters Tel: +65 6416 4283 World Wide Headquarters Lineage Power Corporation 3000 Skyline Drive, Mesquite, TX 75149, USA +1-800-526-7819 (Outside U.S.A.: +1-972-284-2626) www.lineagepower.com e-mail: [email protected] Europe, Middle-East and Africa Headquarters Tel: +49 89 6089 286 India Headquarters Tel: +91 80 28411633 Lineage Power reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Document No: DS03-017 ver.1.21 © 2008 Lineage Power Corporation, (Mesquite, Texas) All International Rights Reserved. PDF No: hw-hc_4-6a.pdf