STMicroelectronics L7806CV Positive voltage regulator ic Datasheet

L78
Positive voltage regulator ICs
Datasheet - production data
Description
The L78 series of three-terminal positive
regulators is available in TO-220, TO-220FP,
D²PAK and DPAK packages and several fixed
output voltages, making it useful in a wide range
of applications.
TO-220
DPAK
These regulators can provide local on-card
regulation, eliminating the distribution problems
associated with single point regulation. Each type
embeds internal current limiting, thermal shutdown and safe area protection, making it
essentially indestructible. If adequate heat sinking
is provided, they can deliver over 1 A output
current. Although designed primarily as fixed
voltage regulators, these devices can be used
with external components to obtain adjustable
voltage and currents.
TO-220FP
D²PAK
Features
• Output current up to 1.5 A
• Output voltages of 5; 6; 8; 8.5; 9; 12; 15; 18;
24 V
• Thermal overload protection
• Short circuit protection
• Output transition SOA protection
• 2 % output voltage tolerance (A version)
• Guaranteed in extended temperature range
(A version)
March 2014
This is information on a product in full production.
DocID2143 Rev 32
1/58
www.st.com
Contents
Positive voltage regulator ICs
Contents
1
Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4
Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6
Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.1
Design consideration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7
Typical performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
8
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
9
Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
10
Order codes
11
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
2/58
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
DocID2143 Rev 32
Positive voltage regulator ICs
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Table 20.
Table 21.
Table 22.
Table 23.
Table 24.
Table 25.
Table 26.
Table 27.
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electrical characteristics of L7805A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Electrical characteristics of L7806A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Electrical characteristics of L7808A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Electrical characteristics of L7809A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Electrical characteristics of L7812A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Electrical characteristics of L7815A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Electrical characteristics of L7824A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Electrical characteristics of L7805C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Electrical characteristics of L7806C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Electrical characteristics of L7808C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Electrical characteristics of L7885C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Electrical characteristics of L7809C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Electrical characteristics of L7812C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Electrical characteristics of L7815C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Electrical characteristics of L7818C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Electrical characteristics of L7824C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
TO-220 (dual gauge) mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
TO-220 SG (single gauge) mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
TO-220FP mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
DPAK mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
D²PAK (SMD 2L STD-ST) mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
D²PAK (SMD 2L Wooseok-subcon.) mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
DPAK and D²PAK tape and reel mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
DocID2143 Rev 32
3/58
58
List of figures
Positive voltage regulator ICs
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
Figure 26.
Figure 27.
Figure 28.
Figure 29.
Figure 30.
Figure 31.
Figure 32.
Figure 33.
Figure 34.
Figure 35.
Figure 36.
Figure 37.
Figure 38.
Figure 39.
Figure 40.
Figure 41.
Figure 42.
Figure 43.
Figure 44.
Figure 45.
Figure 46.
Figure 47.
Figure 48.
4/58
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin connections (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Application circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
DC parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Load regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Ripple rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Fixed output regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Current regulator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Circuit for increasing output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Adjustable output regulator (7 to 30 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
0.5 to 10 V regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
High current voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
High output current with short circuit protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Tracking voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Split power supply (± 15 V - 1 A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Negative output voltage circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Switching regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
High input voltage circuit (configuration 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
High input voltage circuit (configuration 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
High input and output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Reducing power dissipation with dropping resistor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Remote shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Power AM modulator (unity voltage gain, IO £ 0.5). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Adjustable output voltage with temperature compensation . . . . . . . . . . . . . . . . . . . . . . . . 33
Light controllers (VO(min) = VXX + VBE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Protection against input short-circuit with high capacitance loads . . . . . . . . . . . . . . . . . . . 34
Dropout voltage vs. junction temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Peak output current vs. input/output differential voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Supply voltage rejection vs. frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Output voltage vs. junction temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Output impedance vs. frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Quiescent current vs. junction temp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Load transient response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Line transient response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Quiescent current vs. input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
TO-220 (dual gauge) drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
TO-220 SG (single gauge) drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
TO-220FP drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
DPAK drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
DPAK footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
D²PAK (SMD 2L STD-ST) type A drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
D²PAK (SMD 2L Wooseok-subcon.) drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
D²PAK (SMD 2L Wooseok-subcon.) footprint. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Tube for TO-220 (dual gauge) (mm.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Tube for TO-220 (single gauge) (mm.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Tape for DPAK and D2PAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Reel for DPAK and D2PAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
DocID2143 Rev 32
Positive voltage regulator ICs
1
Diagram
Diagram
Figure 1. Block diagram
DocID2143 Rev 32
5/58
58
Pin configuration
2
Positive voltage regulator ICs
Pin configuration
Figure 2. Pin connections (top view)
72
72)3
'3$.
'ð3$.
Figure 3. Schematic diagram
6/58
DocID2143 Rev 32
Positive voltage regulator ICs
3
Maximum ratings
Maximum ratings
Table 1. Absolute maximum ratings
Symbol
Parameter
Value
for VO= 5 to 18 V
35
for VO= 20, 24 V
40
Unit
VI
DC input voltage
IO
Output current
Internally limited
PD
Power dissipation
Internally limited
TSTG
Storage temperature range
TOP
Operating junction temperature range
V
-65 to 150
for L78xxC, L78xxAC
Note:
°C
0 to 125
°C
for L78xxAB
-40 to 125
Absolute maximum ratings are those values beyond which damage to the device may occur.
Functional operation under these condition is not implied.
Table 2. Thermal data
Symbol
Parameter
RthJC
Thermal resistance junction-case
RthJA
Thermal resistance junction-ambient
D²PAK
DPAK
TO-220
TO-220FP
Unit
3
8
5
5
°C/W
62.5
100
50
60
°C/W
Figure 4. Application circuits
DocID2143 Rev 32
7/58
58
Test circuits
4
Positive voltage regulator ICs
Test circuits
Figure 5. DC parameter
Figure 6. Load regulation
Figure 7. Ripple rejection
8/58
DocID2143 Rev 32
Positive voltage regulator ICs
5
Electrical characteristics
Electrical characteristics
VI = 10 V, IO = 1 A, TJ = 0 to 125 °C (L7805AC), TJ = -40 to 125 °C (L7805AB), unless
otherwise specified(a).
Table 3. Electrical characteristics of L7805A
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
4.9
5
5.1
V
VO
Output voltage
IO = 5 mA to 1 A, VI = 7.5 to 18 V
4.8
5
5.2
V
VO
Output voltage
IO = 1 A, VI = 18 to 20 V, TJ = 25°C
4.8
5
5.2
V
VI = 7.5 to 25 V, IO = 500 mA, TJ = 25°C
7
50
mV
VI = 8 to 12 V
10
50
mV
VI = 8 to 12 V, TJ = 25°C
2
25
mV
VI = 7.3 to 20 V, TJ = 25°C
7
50
mV
IO = 5 mA to 1 A
25
100
IO = 5 mA to 1.5 A, TJ = 25°C
30
100
IO = 250 to 750 mA
8
50
4.3
6
mA
6
mA
VI = 8 to 23 V, IO = 500 mA
0.8
mA
VI = 7.5 to 20 V, TJ = 25°C
0.8
mA
IO = 5 mA to 1 A
0.5
mA
ΔVO (1)
ΔVO
(1)
Iq
ΔIq
Line regulation
Load regulation
Quiescent current
Quiescent current change
TJ = 25°C
mV
Supply voltage rejection
VI = 8 to 18 V, f = 120 Hz, IO = 500 mA
68
dB
Vd
Dropout voltage
IO = 1 A, TJ = 25°C
2
V
eN
Output noise voltage
TA = 25°C, B =10 Hz to 100 kHz
10
µV/VO
RO
Output resistance
f = 1 kHz
17
mΩ
Isc
Short circuit current
VI = 35 V, TA = 25°C
0.2
A
Iscp
Short circuit peak current
TJ = 25°C
2.2
A
-1.1
mV/°C
SVR
ΔVO/ΔT
Output voltage drift
1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be
taken into account separately. Pulse testing with low duty cycle is used.
a. Minimum load current for regulation is 5 mA.
DocID2143 Rev 32
9/58
58
Electrical characteristics
Positive voltage regulator ICs
VI = 11 V, IO = 1 A, TJ = 0 to 125 °C (L7806AC), TJ = -40 to 125 °C (L7806AB), unless
otherwise specified(b).
Table 4. Electrical characteristics of L7806A
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
5.88
6
6.12
V
VO
Output voltage
IO = 5 mA to 1 A, VI = 8.6 to 19 V
5.76
6
6.24
V
VO
Output voltage
IO = 1 A, VI = 19 to 21 V, TJ = 25°C
5.76
6
6.24
V
VI = 8.6 to 25 V, IO = 500 mA, TJ = 25°C
9
60
mV
VI = 9 to 13 V
11
60
mV
VI = 9 to 13 V, TJ = 25°C
3
30
mV
VI = 8.3 to 21 V, TJ = 25°C
9
60
mV
IO = 5 mA to 1 A
25
100
IO = 5 mA to 1.5 A, TJ = 25°C
30
100
IO = 250 to 750 mA
10
50
TJ = 25°C
4.3
6
mA
6
mA
VI = 9 to 24 V, IO = 500 mA
0.8
mA
VI = 8.6 to 21 V, TJ = 25°C
0.8
mA
IO = 5 mA to 1 A
0.5
mA
ΔVO (1)
ΔVO
(1)
Iq
ΔIq
SVR
Line regulation
Load regulation
Quiescent current
Quiescent current change
mV
Supply voltage rejection
VI = 9 to 19 V, f = 120 Hz, IO = 500 mA
65
dB
Vd
Dropout voltage
IO = 1 A, TJ = 25°C
2
V
eN
Output noise voltage
TA = 25°C, B =10 Hz to 100 kHz
10
µV/VO
RO
Output resistance
f = 1 kHz
17
mΩ
Isc
Short circuit current
VI = 35 V, TA = 25°C
0.2
A
Iscp
Short circuit peak current
TJ = 25°C
2.2
A
-0.8
mV/°C
ΔVO/ΔT
Output voltage drift
1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be
taken into account separately. Pulse testing with low duty cycle is used.
b. Minimum load current for regulation is 5 mA.
10/58
DocID2143 Rev 32
Positive voltage regulator ICs
Electrical characteristics
VI = 14 V, IO = 1 A, TJ = 0 to 125 °C (L7808AC), TJ = -40 to 125 °C (L7808AB), unless
otherwise specified(c).
Table 5. Electrical characteristics of L7808A
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
7.84
8
8.16
V
VO
Output voltage
IO = 5 mA to 1 A, VI = 10.6 to 21 V
7.7
8
8.3
V
VO
Output voltage
IO = 1 A, VI = 21 to 23 V, TJ = 25°C
7.7
8
8.3
V
VI = 10.6 to 25 V, IO = 500 mA,
TJ = 25°C
12
80
mV
VI = 11 to 17 V
15
80
mV
VI = 11 to 17 V, TJ = 25°C
5
40
mV
VI = 10.4 to 23 V, TJ = 25°C
12
80
mV
IO = 5 mA to 1 A
25
100
IO = 5 mA to 1.5 A, TJ = 25°C
30
100
IO = 250 to 750 mA
10
50
TJ = 25°C
4.3
6
mA
6
mA
VI = 11 to 23 V, IO = 500 mA
0.8
mA
VI = 10.6 to 23 V, TJ = 25°C
0.8
mA
IO = 5 mA to 1 A
0.5
mA
ΔVO (1)
ΔVO
(1)
Iq
ΔIq
Line regulation
Load regulation
Quiescent current
Quiescent current change
mV
Supply voltage rejection
VI = 11.5 to 21.5 V, f = 120 Hz,
IO = 500 mA
62
dB
Vd
Dropout voltage
IO = 1 A, TJ = 25°C
2
V
eN
Output noise voltage
TA = 25°C, B =10 Hz to 100 kHz
10
µV/VO
RO
Output resistance
f = 1 kHz
18
mΩ
Isc
Short circuit current
VI = 35 V, TA = 25°C
0.2
A
Iscp
Short circuit peak current
TJ = 25°C
2.2
A
-0.8
mV/°C
SVR
ΔVO/ΔT
Output voltage drift
1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be
taken into account separately. Pulse testing with low duty cycle is used.
c. Minimum load current for regulation is 5 mA.
DocID2143 Rev 32
11/58
58
Electrical characteristics
Positive voltage regulator ICs
VI = 15 V, IO = 1 A, TJ = 0 to 125 °C (L7809AC), TJ = -40 to 125 °C (L7809AB), unless
otherwise specified(d).
Table 6. Electrical characteristics of L7809A
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
8.82
9
9.18
V
VO
Output voltage
IO = 5 mA to 1 A, VI = 10.6 to 22 V
8.65
9
9.35
V
VO
Output voltage
IO = 1 A, VI = 22 to 24 V, TJ = 25°C
8.65
9
9.35
V
VI = 10.6 to 25 V, IO = 500 mA,
TJ = 25°C
12
90
mV
VI = 11 to 17 V
15
90
mV
VI = 11 to 17 V, TJ = 25°C
5
45
mV
VI = 11.4 to 23 V, TJ = 25°C
12
90
mV
IO = 5 mA to 1 A
25
100
IO = 5 mA to 1.5 A, TJ = 25°C
30
100
IO = 250 to 750 mA
10
50
TJ = 25°C
4.3
6
mA
6
mA
VI = 11 to 25 V, IO = 500 mA
0.8
mA
VI = 10.6 to 23 V, TJ = 25°C
0.8
mA
IO = 5 mA to 1 A
0.5
mA
ΔVO (1)
ΔVO
(1)
Iq
ΔIq
Line regulation
Load regulation
Quiescent current
Quiescent current change
mV
Supply voltage rejection
VI = 11.5 to 21.5 V, f = 120 Hz,
IO = 500 mA
61
dB
Vd
Dropout voltage
IO = 1 A, TJ = 25°C
2
V
eN
Output noise voltage
TA = 25°C, B =10 Hz to 100 kHz
10
µV/VO
RO
Output resistance
f = 1 kHz
18
mΩ
Isc
Short circuit current
VI = 35 V, TA = 25°C
0.2
A
Iscp
Short circuit peak current
TJ = 25°C
2.2
A
-0.8
mV/°C
SVR
ΔVO/ΔT
Output voltage drift
1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be
taken into account separately. Pulse testing with low duty cycle is used.
d. Minimum load current for regulation is 5 mA.
12/58
DocID2143 Rev 32
Positive voltage regulator ICs
Electrical characteristics
VI = 19 V, IO = 1 A, TJ = 0 to 125 °C (L7812AC), TJ = -40 to 125 °C (L7812AB), unless
otherwise specified(e).
Table 7. Electrical characteristics of L7812A
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
11.75
12
12.25
V
VO
Output voltage
IO = 5 mA to 1 A, VI = 14.8 to 25 V
11.5
12
12.5
V
VO
Output voltage
IO = 1 A, VI = 25 to 27 V, TJ = 25°C
11.5
12
12.5
V
VI = 14.8 to 30 V, IO = 500 mA,
TJ = 25°C
13
120
mV
VI = 16 to 12 V
16
120
mV
VI = 16 to 12 V, TJ = 25°C
6
60
mV
VI = 14.5 to 27 V, TJ = 25°C
13
120
mV
IO = 5 mA to 1 A
25
100
IO = 5 mA to 1.5 A, TJ = 25°C
30
100
IO = 250 to 750 mA
10
50
TJ = 25°C
4.4
6
mA
6
mA
VI = 15 to 30 V, IO = 500 mA
0.8
mA
VI = 14.8 to 27 V, TJ = 25°C
0.8
mA
IO = 5 mA to 1 A
0.5
mA
ΔVO (1)
ΔVO
(1)
Iq
ΔIq
SVR
Line regulation
Load regulation
Quiescent current
Quiescent current change
mV
Supply voltage rejection
VI = 15 to 25 V, f = 120 Hz, IO = 500 mA
60
dB
Vd
Dropout voltage
IO = 1 A, TJ = 25°C
2
V
eN
Output noise voltage
TA = 25°C, B = 10 Hz to 100 kHz
10
µV/VO
RO
Output resistance
f = 1 kHz
18
mΩ
Isc
Short circuit current
VI = 35 V, TA = 25°C
0.2
A
Iscp
Short circuit peak current
TJ = 25°C
2.2
A
-1
mV/°C
ΔVO/ΔT
Output voltage drift
1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be
taken into account separately. Pulse testing with low duty cycle is used.
e. Minimum load current for regulation is 5 mA.
DocID2143 Rev 32
13/58
58
Electrical characteristics
Positive voltage regulator ICs
VI = 23 V, IO = 1 A, TJ = 0 to 125 °C (L7815AC), TJ = -40 to 125 °C (L7815AB), unless
otherwise specified(f).
Table 8. Electrical characteristics of L7815A
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
14.7
15
15.3
V
VO
Output voltage
IO = 5 mA to 1 A, VI = 17.9 to 28 V
14.4
15
15.6
V
VO
Output voltage
IO = 1 A, VI = 28 to 30 V, TJ = 25°C
14.4
15
15.6
V
VI = 17.9 to 30 V, IO = 500 mA,
TJ = 25°C
13
150
mV
VI = 20 to 26 V
16
150
mV
VI = 20 to 26 V, TJ = 25°C
6
75
mV
VI = 17.5 to 30 V, TJ = 25°C
13
150
mV
IO = 5 mA to 1 A
25
100
IO = 5 mA to 1.5 A, TJ = 25°C
30
100
IO = 250 to 750 mA
10
50
TJ = 25°C
4.4
6
mA
6
mA
VI = 17.5 to 30 V, IO = 500 mA
0.8
mA
VI = 17.5 to 30 V, TJ = 25°C
0.8
mA
IO = 5 mA to 1 A
0.5
mA
ΔVO (1)
ΔVO
(1)
Iq
ΔIq
Line regulation
Load regulation
Quiescent current
Quiescent current change
mV
Supply voltage rejection
VI = 18.5 to 28.5 V, f = 120 Hz,
IO = 500 mA
58
dB
Vd
Dropout voltage
IO = 1 A, TJ = 25°C
2
V
eN
Output noise voltage
TA = 25°C, B = 10Hz to 100 kHz
10
µV/VO
RO
Output resistance
f = 1 kHz
19
mΩ
Isc
Short circuit current
VI = 35 V, TA = 25°C
0.2
A
Iscp
Short circuit peak current
TJ = 25°C
2.2
A
-1
mV/°C
SVR
ΔVO/ΔT
Output voltage drift
1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be
taken into account separately. Pulse testing with low duty cycle is used.
f.
14/58
Minimum load current for regulation is 5 mA.
DocID2143 Rev 32
Positive voltage regulator ICs
Electrical characteristics
VI = 33 V, IO = 1 A, TJ = 0 to 125 °C (L7824AC), TJ = -40 to 125 °C (L7824AB), unless
otherwise specified(g).
Table 9. Electrical characteristics of L7824A
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
23.5
24
24.5
V
VO
Output voltage
TJ = 25°C
VO
Output voltage
IO = 5 mA to 1 A, VI = 27.3 to 37 V
23
24
25
V
VO
Output voltage
IO = 1 A, VI = 37 to 38 V, TJ = 25°C
23
24
25
V
VI = 27 to 38 V, IO = 500 mA, TJ = 25°C
31
240
mV
VI = 30 to 36 V
35
200
mV
VI = 30 to 36 V, TJ = 25°C
14
120
mV
VI = 26.7 to 38 V, TJ = 25°C
31
240
mV
IO = 5 mA to 1 A
25
100
IO = 5 mA to 1.5 A, TJ = 25°C
30
100
IO = 250 to 750 mA
10
50
TJ = 25°C
4.6
6
mA
6
mA
VI = 27.3 to 38 V, IO = 500 mA
0.8
mA
VI = 27.3 to 38 V, TJ = 25°C
0.8
mA
IO = 5 mA to 1 A
0.5
mA
ΔVO (1)
ΔVO
(1)
Iq
ΔIq
SVR
Line regulation
Load regulation
Quiescent current
Quiescent current change
mV
Supply voltage rejection
VI = 28 to 38 V, f = 120 Hz, IO = 500 mA
54
dB
Vd
Dropout voltage
IO = 1 A, TJ = 25°C
2
V
eN
Output noise voltage
TA = 25°C, B = 10 Hz to 100 kHz
10
µV/VO
RO
Output resistance
f = 1 kHz
20
mΩ
Isc
Short circuit current
VI = 35 V, TA = 25°C
0.2
A
Iscp
Short circuit peak current
TJ = 25°C
2.2
A
-1.5
mV/°C
ΔVO/ΔT
Output voltage drift
1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be
taken into account separately. Pulse testing with low duty cycle is used.
g. Minimum load current for regulation is 5 mA.
DocID2143 Rev 32
15/58
58
Electrical characteristics
Positive voltage regulator ICs
Refer to the test circuits, TJ = 0 to 125 °C, VI = 10 V, IO = 500 mA, CI = 0.33 µF, CO = 0.1 µF
unless otherwise specified(h).
Table 10. Electrical characteristics of L7805C
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
4.8
5
5.2
V
VO
Output voltage
IO = 5 mA to 1 A, VI = 7 to 18 V
4.75
5
5.25
V
VO
Output voltage
IO = 1 A, VI = 18 to 20V, TJ = 25°C
4.75
5
5.25
V
ΔVO(1)
VI = 7 to 25 V, TJ = 25°C
3
100
Line regulation
VI = 8 to 12 V, TJ = 25°C
1
50
ΔVO(1)
Load regulation
Id
ΔId
ΔVO/ΔT
Quiescent current
Quiescent current change
mV
IO = 5 mA to 1.5 A, TJ = 25°C
100
IO = 250 to 750 mA, TJ = 25°C
50
TJ = 25°C
8
mV
IO = 5 mA to 1 A
0.5
VI = 7 to 23 V
0.8
mA
mA
Output voltage drift
IO = 5 mA
Output noise voltage
B = 10 Hz to 100 kHz, TJ = 25°C
Supply voltage rejection
VI = 8 to 18 V, f = 120 Hz
Vd
Dropout voltage
IO = 1 A, TJ = 25°C
2
V
RO
Output resistance
f = 1 kHz
17
mΩ
Isc
Short circuit current
VI = 35 V, TJ = 25°C
0.75
A
Iscp
Short circuit peak current
TJ = 25°C
2.2
A
eN
SVR
-1.1
mV/°C
40
µV/VO
62
dB
1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be
taken into account separately. Pulse testing with low duty cycle is used.
h. Minimum load current for regulation is 5 mA.
16/58
DocID2143 Rev 32
Positive voltage regulator ICs
Electrical characteristics
Refer to the test circuits, TJ = 0 to 125 °C, VI = 11 V, IO = 500 mA, CI = 0.33 µF, CO = 0.1 µF
unless otherwise specified(i).
Table 11. Electrical characteristics of L7806C
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
5.75
6
6.25
V
VO
Output voltage
IO = 5 mA to 1 A, VI = 8 to 19 V
5.7
6
6.3
V
VO
Output voltage
IO = 1 A, VI = 19 to 21 V, TJ = 25°C
5.7
6
6.3
V
ΔVO(1)
Line regulation
ΔVO(1)
Load regulation
Id
ΔId
ΔVO/ΔT
Quiescent current
Quiescent current change
VI = 8 to 25 V, TJ = 25°C
120
VI = 9 to 13 V, TJ = 25°C
60
IO = 5 mA to 1.5 A, TJ = 25°C
120
IO = 250 to 750 mA, TJ = 25°C
60
TJ = 25°C
8
mV
mV
IO = 5 mA to 1 A
0.5
VI = 8 to 24 V
1.3
mA
mA
Output voltage drift
IO = 5 mA
Output noise voltage
B = 10 Hz to 100 kHz, TJ = 25°C
Supply voltage rejection
VI = 9 to 19 V, f = 120 Hz
Vd
Dropout voltage
IO = 1 A, TJ = 25°C
2
V
RO
Output resistance
f = 1 kHz
19
mΩ
Isc
Short circuit current
VI = 35 V, TJ = 25°C
0.55
A
Iscp
Short circuit peak current
TJ = 25°C
2.2
A
eN
SVR
-0.8
mV/°C
45
µV/VO
59
dB
1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be
taken into account separately. Pulse testing with low duty cycle is used.
i.
Minimum load current for regulation is 5 mA.
DocID2143 Rev 32
17/58
58
Electrical characteristics
Positive voltage regulator ICs
Refer to the test circuits, TJ = 0 to 125 °C, VI = 14 V, IO = 500 mA, CI = 0.33 µF, CO = 0.1 µF
unless otherwise specified(j).
Table 12. Electrical characteristics of L7808C
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
7.7
8
8.3
V
VO
Output voltage
IO = 5 mA to 1 A, VI = 10.5 to 21 V
7.6
8
8.4
V
VO
Output voltage
IO = 1 A, VI = 21 to 25 V, TJ = 25°C
7.6
8
8.4
V
ΔVO(1)
Line regulation
ΔVO(1)
Load regulation
Id
ΔId
ΔVO/ΔT
Quiescent current
Quiescent current change
VI = 10.5 to 25 V, TJ = 25°C
160
VI = 11 to 17 V, TJ = 25°C
80
IO = 5 mA to 1.5 A, TJ = 25°C
160
IO = 250 to 750 mA, TJ = 25°C
80
TJ = 25°C
8
mV
mV
IO = 5 mA to 1 A
0.5
VI = 10.5 to 25 V
1
mA
mA
Output voltage drift
IO = 5 mA
Output noise voltage
B = 10 Hz to 100 kHz, TJ = 25°C
Supply voltage rejection
VI = 11.5 to 21.5 V, f = 120 Hz
Vd
Dropout voltage
IO = 1 A, TJ = 25°C
2
V
RO
Output resistance
f = 1 kHz
16
mΩ
Isc
Short circuit current
VI = 35 V, TJ = 25°C
0.45
A
Iscp
Short circuit peak current
TJ = 25°C
2.2
A
eN
SVR
-0.8
mV/°C
52
µV/VO
56
dB
1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be
taken into account separately. Pulse testing with low duty cycle is used.
j.
18/58
Minimum load current for regulation is 5 mA.
DocID2143 Rev 32
Positive voltage regulator ICs
Electrical characteristics
Refer to the test circuits, TJ = 0 to 125 °C, VI = 14.5 V, IO = 500 mA, CI = 0.33 µF,
CO = 0.1 µF unless otherwise specified(k).
Table 13. Electrical characteristics of L7885C
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
8.2
8.5
8.8
V
VO
Output voltage
IO = 5 mA to 1 A, VI = 11 to 21.5 V
8.1
8.5
8.9
V
VO
Output voltage
IO = 1 A, VI = 21.5 to 26 V, TJ = 25°C
8.1
8.5
8.9
V
ΔVO(1)
Line regulation
ΔVO(1)
Load regulation
Id
ΔId
ΔVO/ΔT
Quiescent current
Quiescent current change
VI = 11 to 27 V, TJ = 25°C
160
VI = 11.5 to 17.5 V, TJ = 25°C
80
IO = 5 mA to 1.5 A, TJ = 25°C
160
IO = 250 to 750 mA, TJ = 25°C
80
TJ = 25°C
8
mV
mV
IO = 5 mA to 1 A
mA
0.5
mA
VI = 11 to 26 V
1
Output voltage drift
IO = 5 mA
Output noise voltage
B = 10 Hz to 100 kHz, TJ = 25°C
Supply voltage rejection
VI = 12 to 22 V, f = 120 Hz
Vd
Dropout voltage
IO = 1 A, TJ = 25°C
2
V
RO
Output resistance
f = 1 kHz
16
mΩ
Isc
Short circuit current
VI = 35 V, TJ = 25°C
0.45
A
Iscp
Short circuit peak current
TJ = 25°C
2.2
A
eN
SVR
-0.8
mV/°C
55
µV/VO
56
dB
1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be
taken into account separately. Pulse testing with low duty cycle is used.
k. Minimum load current for regulation is 5 mA.
DocID2143 Rev 32
19/58
58
Electrical characteristics
Positive voltage regulator ICs
Refer to the test circuits, TJ = 0 to 125 °C, VI = 15 V, IO = 500 mA, CI = 0.33 µF, CO = 0.1 µF
unless otherwise specified(l).
Table 14. Electrical characteristics of L7809C
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
8.64
9
9.36
V
VO
Output voltage
IO = 5 mA to 1 A, VI = 11.5 to 22 V
8.55
9
9.45
V
VO
Output voltage
IO = 1 A, VI = 22 to 26 V, TJ = 25°C
8.55
9
9.45
V
ΔVO(1)
Line regulation
ΔVO(1)
Load regulation
Id
ΔId
ΔVO/ΔT
Quiescent current
Quiescent current change
VI = 11.5 to 26 V, TJ = 25°C
180
VI = 12 to 18 V, TJ = 25°C
90
IO = 5 mA to 1.5 A, TJ = 25°C
180
IO = 250 to 750 mA, TJ = 25°C
90
TJ = 25°C
8
mV
mV
IO = 5 mA to 1 A
0.5
VI = 11.5 to 26 V
1
mA
mA
Output voltage drift
IO = 5 mA
-1
mV/°C
Output noise voltage
B = 10 Hz to 100 kHz, TJ = 25°C
70
µV/VO
Supply voltage rejection
VI = 12 to 23 V, f = 120 Hz
Vd
Dropout voltage
IO = 1 A, TJ = 25°C
2
V
RO
Output resistance
f = 1 kHz
17
mΩ
Isc
Short circuit current
VI = 35 V, TJ = 25°C
0.40
A
Iscp
Short circuit peak current
TJ = 25°C
2.2
A
eN
SVR
55
dB
1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be
taken into account separately. Pulse testing with low duty cycle is used.
l.
20/58
Minimum load current for regulation is 5 mA.
DocID2143 Rev 32
Positive voltage regulator ICs
Electrical characteristics
Refer to the test circuits, TJ = 0 to 125 °C, VI = 19 V, IO = 500 mA, CI = 0.33 µF, CO = 0.1 µF
unless otherwise specified(m).
Table 15. Electrical characteristics of L7812C
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
11.5
12
12.5
V
VO
Output voltage
IO = 5 mA to 1 A, VI = 14.5 to 25 V
11.4
12
12.6
V
VO
Output voltage
IO = 1 A, VI = 25 to 27 V, TJ = 25°C
11.4
12
12.6
V
ΔVO(1)
Line regulation
ΔVO(1)
Load regulation
Id
ΔId
ΔVO/ΔT
Quiescent current
Quiescent current change
VI = 14.5 to 30 V, TJ = 25°C
240
VI = 16 to 22 V, TJ = 25°C
120
IO = 5 mA to 1.5 A, TJ = 25°C
240
IO = 250 to 750 mA, TJ = 25°C
120
mV
mV
TJ = 25°C
8
IO = 5 mA to 1 A
0.5
VI = 14.5 to 30 V
1
mA
mA
Output voltage drift
IO = 5 mA
-1
mV/°C
Output noise voltage
B = 10 Hz to 100 kHz, TJ = 25°C
75
µV/VO
Supply voltage rejection
VI = 15 to 25 V, f = 120 Hz
Vd
Dropout voltage
IO = 1 A, TJ = 25°C
2
V
RO
Output resistance
f = 1 kHz
18
mΩ
Isc
Short circuit current
VI = 35 V, TJ = 25°C
0.35
A
Iscp
Short circuit peak current
TJ = 25°C
2.2
A
eN
SVR
55
dB
1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be
taken into account separately. Pulse testing with low duty cycle is used.
m. Minimum load current for regulation is 5 mA.
DocID2143 Rev 32
21/58
58
Electrical characteristics
Positive voltage regulator ICs
Refer to the test circuits, TJ = 0 to 125 °C, VI = 23 V, IO = 500 mA, CI = 0.33 µF, CO = 0.1 µF
unless otherwise specified(n).
Table 16. Electrical characteristics of L7815C
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
14.4
15
15.6
V
VO
Output voltage
IO = 5 mA to 1 A, VI = 17.5 to 28 V
14.25
15
15.75
V
VO
Output voltage
IO = 1 A, VI = 28 to 30 V, TJ = 25°C
14.25
15
15.75
V
ΔVO(1)
Line regulation
ΔVO(1)
Load regulation
Id
ΔId
ΔVO/ΔT
Quiescent current
Quiescent current change
VI = 17.5 to 30 V, TJ = 25°C
300
VI = 20 to 26 V, TJ = 25°C
150
IO = 5 mA to 1.5 A, TJ = 25°C
300
IO = 250 to 750 mA, TJ = 25°C
150
mV
mV
TJ = 25°C
8
IO = 5 mA to 1A
0.5
VI = 17.5 to 30 V
1
mA
mA
Output voltage drift
IO = 5 mA
-1
mV/°C
Output noise voltage
B = 10 Hz to 100kHz, TJ = 25°C
90
µV/VO
Supply voltage rejection
VI = 18.5 to 28.5 V, f = 120 Hz
Vd
Dropout voltage
IO = 1 A, TJ = 25°C
2
V
RO
Output resistance
f = 1 kHz
19
mΩ
Isc
Short circuit current
VI = 35 V, TJ = 25°C
0.23
A
Iscp
Short circuit peak current
TJ = 25°C
2.2
A
eN
SVR
54
dB
1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be
taken into account separately. Pulse testing with low duty cycle is used.
n. Minimum load current for regulation is 5 mA.
22/58
DocID2143 Rev 32
Positive voltage regulator ICs
Electrical characteristics
Refer to the test circuits, TJ = 0 to 125 °C, VI = 26 V, IO = 500 mA, CI = 0.33 µF, CO = 0.1 µF
unless otherwise specified(o).
Table 17. Electrical characteristics of L7818C
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
17.3
18
18.7
V
VO
Output voltage
IO = 5 mA to 1 A, VI = 21 to 31 V
17.1
18
18.9
V
VO
Output voltage
IO = 1 A, VI = 31 to 33 V, TJ = 25°C
17.1
18
18.9
V
ΔVO(1)
Line regulation
ΔVO(1)
Load regulation
Id
ΔId
ΔVO/ΔT
Quiescent current
Quiescent current change
VI = 21 to 33 V, TJ = 25°C
360
VI = 24 to 30 V, TJ = 25°C
180
IO = 5 mA to 1.5 A, TJ = 25°C
360
IO = 250 to 750 mA, TJ = 25°C
180
mV
mV
TJ = 25°C
8
IO = 5 mA to 1 A
mA
0.5
mA
VI = 21 to 33 V
1
Output voltage drift
IO = 5 mA
Output noise voltage
B = 10 Hz to 100 kHz, TJ = 25°C
Supply voltage rejection
VI = 22 to 32 V, f = 120 Hz
Vd
Dropout voltage
IO = 1 A, TJ = 25°C
2
V
RO
Output resistance
f = 1 kHz
22
mΩ
Isc
Short circuit current
VI = 35 V, TJ = 25°C
0.20
A
Iscp
Short circuit peak current
TJ = 25°C
2.1
A
eN
SVR
-1
mV/°C
110
µV/VO
53
dB
1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be
taken into account separately. Pulse testing with low duty cycle is used.
o. Minimum load current for regulation is 5 mA.
DocID2143 Rev 32
23/58
58
Electrical characteristics
Positive voltage regulator ICs
Refer to the test circuits, TJ = 0 to 125 °C, VI = 33 V, IO = 500 mA, CI = 0.33 µF, CO = 0.1 µF
unless otherwise specified(p).
Table 18. Electrical characteristics of L7824C
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
23
24
25
V
VO
Output voltage
TJ = 25°C
VO
Output voltage
IO = 5 mA to 1 A, VI = 27 to 37 V
22.8
24
25.2
V
VO
Output voltage
IO = 1 A, VI = 37 to 38 V, TJ = 25°C
22.8
24
25.2
V
ΔVO(1)
Line regulation
ΔVO(1)
Load regulation
Id
ΔId
ΔVO/ΔT
Quiescent current
Quiescent current change
VI = 27 to 38 V, TJ = 25°C
480
VI = 30 to 36 V, TJ = 25°C
240
IO = 5 mA to 1.5 A, TJ = 25°C
480
IO = 250 to 750 mA, TJ = 25°C
240
mV
mV
TJ = 25°C
8
IO = 5 mA to 1 A
mA
0.5
mA
VI = 27 to 38 V
1
Output voltage drift
IO = 5 mA
-1.5
mV/°C
Output noise voltage
B = 10 Hz to 100 kHz, TJ = 25°C
170
µV/VO
Supply voltage rejection
VI = 28 to 38 V, f = 120 Hz
Vd
Dropout voltage
IO = 1 A, TJ = 25°C
2
V
RO
Output resistance
f = 1 kHz
28
mΩ
Isc
Short circuit current
VI = 35 V, TJ = 25°C
0.15
A
Iscp
Short circuit peak current
TJ = 25°C
2.1
A
eN
SVR
50
dB
1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be
taken into account separately. Pulse testing with low duty cycle is used.
p. Minimum load current for regulation is 5 mA.
24/58
DocID2143 Rev 32
Positive voltage regulator ICs
Application information
6
Application information
6.1
Design consideration
The L78 Series of fixed voltage regulators are designed with thermal overload protection
that shuts down the circuit when subjected to an excessive power overload condition,
internal short-circuit protection that limits the maximum current the circuit will pass, and
output transistor safe-area compensation that reduces the output short-circuit current as the
voltage across the pass transistor is increased. In many low current applications,
compensation capacitors are not required. However, it is recommended that the regulator
input be bypassed with capacitor if the regulator is connected to the power supply filter with
long lengths, or if the output load capacitance is large. An input bypass capacitor should be
selected to provide good high frequency characteristics to insure stable operation under all
load conditions. A 0.33 µF or larger tantalum, mylar or other capacitor having low internal
impedance at high frequencies should be chosen. The bypass capacitor should be mounted
with the shortest possible leads directly across the regulators input terminals. Normally good
construction techniques should be used to minimize ground loops and lead resistance drops
since the regulator has no external sense lead.
The addition of an operational amplifier allows adjustment to higher or intermediate values
while retaining regulation characteristics. The minimum voltage obtained with the
arrangement is 2 V greater than the regulator voltage.
The circuit of Figure 13 can be modified to provide supply protection against short circuit by
adding a short circuit sense resistor, RSC, and an additional PNP transistor. The current
sensing PNP must be able to handle the short circuit current of the three terminal regulator
Therefore a four ampere plastic power transistor is specified.
Figure 8. Fixed output regulator
1. Although no output capacitor is need for stability, it does improve transient response.
2. Required if regulator is located an appreciable distance from power supply filter.
DocID2143 Rev 32
25/58
58
Application information
Positive voltage regulator ICs
Figure 9. Current regulator
,2 9;;5,G
Figure 10. Circuit for increasing output voltage
,5 Ż,G
92 9;; 55 ,G5
26/58
DocID2143 Rev 32
Positive voltage regulator ICs
Application information
Figure 11. Adjustable output regulator (7 to 30 V)
Figure 12. 0.5 to 10 V regulator
VO=VXXR4/R1
DocID2143 Rev 32
27/58
58
Application information
Positive voltage regulator ICs
Figure 13. High current voltage regulator
9%(4
5 BBBBBBBBBBBBBB
,5(4 ,4E4
9%(4
,2 ,5(*4 ,5(*BBBBB
B
5
Figure 14. High output current with short circuit protection
56& 9%(
%(4
4,6&
28/58
DocID2143 Rev 32
Positive voltage regulator ICs
Application information
Figure 15. Tracking voltage regulator
Figure 16. Split power supply (± 15 V - 1 A)
* Against potential latch-up problems.
DocID2143 Rev 32
29/58
58
Application information
Positive voltage regulator ICs
Figure 17. Negative output voltage circuit
Figure 18. Switching regulator
Figure 19. High input voltage circuit (configuration 1)
9,1 9, 9=9%(
30/58
DocID2143 Rev 32
Positive voltage regulator ICs
Application information
Figure 20. High input voltage circuit (configuration 2)
Figure 21. High input and output voltage
92 9;;9=
Figure 22. Reducing power dissipation with dropping resistor
9, PLQ 9;;9'523 PD[
5 BBBB
BBBBBB
BBBBBB
BBBBBB
BBBBBB
BBBB
,2 PD[[ ,G PD[
DocID2143 Rev 32
31/58
58
Application information
Positive voltage regulator ICs
Figure 23. Remote shutdown
Figure 24. Power AM modulator (unity voltage gain, IO ≤ 0.5)
Note:
32/58
The circuit performs well up to 100 kHz.
DocID2143 Rev 32
Positive voltage regulator ICs
Application information
Figure 25. Adjustable output voltage with temperature compensation
92 9;; 55 9%(
Note:
Q2 is connected as a diode in order to compensate the variation of the Q1 VBE with the
temperature. C allows a slow rise time of the VO.
Figure 26. Light controllers (VO(min) = VXX + VBE)
92ULVHVZKHQWKHOLJKWJRHVXS
92IDOOVZKHQWKHOLJKWJRHVXS
DocID2143 Rev 32
33/58
58
Application information
Positive voltage regulator ICs
Figure 27. Protection against input short-circuit with high capacitance loads
Note:
34/58
Application with high capacitance loads and an output voltage greater than 6 volts need an
external diode (see Figure 22 on page 31) to protect the device against input short circuit. In
this case the input voltage falls rapidly while the output voltage decrease slowly. The
capacitance discharges by means of the base-emitter junction of the series pass transistor
in the regulator. If the energy is sufficiently high, the transistor may be destroyed. The
external diode by-passes the current from the IC to ground.
DocID2143 Rev 32
Positive voltage regulator ICs
7
Typical performance
Typical performance
Figure 28. Dropout voltage vs. junction
temperature
Figure 29. Peak output current vs. input/output
differential voltage
Figure 30. Supply voltage rejection vs.
frequency
Figure 31. Output voltage vs. junction
temperature
DocID2143 Rev 32
35/58
58
Typical performance
Positive voltage regulator ICs
Figure 32. Output impedance vs. frequency
Figure 33. Quiescent current vs. junction temp.
Figure 34. Load transient response
Figure 35. Line transient response
Figure 36. Quiescent current vs. input voltage
36/58
DocID2143 Rev 32
Positive voltage regulator ICs
8
Package mechanical data
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
DocID2143 Rev 32
37/58
58
Package mechanical data
Positive voltage regulator ICs
Figure 37. TO-220 (dual gauge) drawing
BW\SH$B5HYB7
38/58
DocID2143 Rev 32
Positive voltage regulator ICs
Package mechanical data
Table 19. TO-220 (dual gauge) mechanical data
mm
Dim.
Min.
Typ.
Max.
A
4.40
4.60
b
0.61
0.88
b1
1.14
1.70
c
0.48
0.70
D
15.25
15.75
D1
1.27
E
10
10.40
e
2.40
2.70
e1
4.95
5.15
F
1.23
1.32
H1
6.20
6.60
J1
2.40
2.72
L
13
14
L1
3.50
3.93
L20
16.40
L30
28.90
∅P
3.75
3.85
Q
2.65
2.95
DocID2143 Rev 32
39/58
58
Package mechanical data
Positive voltage regulator ICs
Figure 38. TO-220 SG (single gauge) drawing
BUHY'
40/58
DocID2143 Rev 32
Positive voltage regulator ICs
Package mechanical data
Table 20. TO-220 SG (single gauge) mechanical data
mm
Dim.
Min.
Typ.
Max.
A
4.40
4.60
b
0.61
0.88
b1
1.14
1.70
c
0.48
0.70
D
15.25
15.75
E
10
10.40
e
2.40
2.70
e1
4.95
5.15
F
0.51
0.60
H1
6.20
6.60
J1
2.40
2.72
L
13
14
L1
3.50
3.93
L20
16.40
L30
28.90
∅P
3.75
3.85
Q
2.65
2.95
DocID2143 Rev 32
41/58
58
Package mechanical data
Positive voltage regulator ICs
Figure 39. TO-220FP drawing
7012510A-H
42/58
DocID2143 Rev 32
Positive voltage regulator ICs
Package mechanical data
Table 21. TO-220FP mechanical data
mm.
Dim.
Min.
Typ.
Max.
A
4.40
4.60
B
2.5
2.7
D
2.5
2.75
E
0.45
0.70
F
0.75
1
F1
1.15
1.50
F2
1.15
1.50
G
4.95
5.2
G1
2.4
2.7
H
10.0
10.40
L2
16
L3
28.6
30.6
L4
9.8
10.6
L5
2.9
3.6
L6
15.9
16.4
L7
9
9.3
DIA.
3
3.2
DocID2143 Rev 32
43/58
58
Package mechanical data
Positive voltage regulator ICs
Figure 40. DPAK drawing
0068772_K
44/58
DocID2143 Rev 32
Positive voltage regulator ICs
Package mechanical data
Table 22. DPAK mechanical data
mm
Dim.
Min.
Typ.
Max.
A
2.20
2.40
A1
0.90
1.10
A2
0.03
0.23
b
0.64
0.90
b4
5.20
5.40
c
0.45
0.60
c2
0.48
0.60
D
6.00
6.20
D1
E
5.10
6.40
6.60
E1
4.70
e
2.28
e1
4.40
4.60
H
9.35
10.10
L
1.00
1.50
(L1)
2.80
L2
0.80
L4
0.60
1.00
R
V2
0.20
0°
8°
DocID2143 Rev 32
45/58
58
Package mechanical data
Positive voltage regulator ICs
Figure 41. DPAK footprint (q)
Footprint_REV_K
q. All dimensions are in millimeters
46/58
DocID2143 Rev 32
Positive voltage regulator ICs
Package mechanical data
Figure 42. D²PAK (SMD 2L STD-ST) type A drawing
0079457_T
DocID2143 Rev 32
47/58
58
Package mechanical data
Positive voltage regulator ICs
Table 23. D²PAK (SMD 2L STD-ST) mechanical data
mm
Dim.
Min.
Typ.
A
4.40
4.60
A1
0.03
0.23
b
0.70
0.93
b2
1.14
1.70
c
0.45
0.60
c2
1.23
1.36
D
8.95
9.35
D1
7.50
E
10
E1
8.50
10.40
e
2.54
e1
4.88
5.28
H
15
15.85
J1
2.49
2.69
L
2.29
2.79
L1
1.27
1.40
L2
1.30
1.75
R
V2
48/58
Max.
0.4
0°
8°
DocID2143 Rev 32
Positive voltage regulator ICs
Package mechanical data
Figure 43. D²PAK (SMD 2L Wooseok-subcon.) drawing
0079457_T
DocID2143 Rev 32
49/58
58
Package mechanical data
Positive voltage regulator ICs
Table 24. D²PAK (SMD 2L Wooseok-subcon.) mechanical data
mm
Dim.
Min.
Typ.
A
4.30
4.70
A1
0
0.20
b
0.70
0.90
b2
1.17
1.37
c
0.45
0.50
0.60
c2
1.25
1.30
1.40
D
9
9.20
9.40
D1
7.50
E
10
E1
8.50
10.40
e
2.54
e1
4.88
5.08
H
15
15.30
J1
2.20
2.60
L
1.79
2.79
L1
1
1.40
L2
1.20
1.60
R
V2
50/58
Max.
0.30
0°
3°
DocID2143 Rev 32
Positive voltage regulator ICs
Package mechanical data
Figure 44. D²PAK (SMD 2L Wooseok-subcon.) footprint
DocID2143 Rev 32
51/58
58
Packaging mechanical data
9
Positive voltage regulator ICs
Packaging mechanical data
Figure 45. Tube for TO-220 (dual gauge) (mm.)
Figure 46. Tube for TO-220 (single gauge) (mm.)
52/58
DocID2143 Rev 32
Positive voltage regulator ICs
Packaging mechanical data
Figure 47. Tape for DPAK and D2PAK
10 pitches cumulative
tolerance on tape +/- 0.2 mm
T
P0
Top cover
tape
P2
D
E
F
B1
W
K0
B0
For machine ref. only
including draft and
radii concentric around B0
A0
P1
D1
User direction of feed
R
Bending radius
User direction of feed
AM08852v1
Figure 48. Reel for DPAK and D2PAK
T
REEL DIMENSIONS
40mm min.
Access hole
At sl ot location
B
D
C
N
A
Full radius
Tape slot
in core for
tape start 25 mm min.
width
G measured at hub
AM08851v2
DocID2143 Rev 32
53/58
58
Packaging mechanical data
Positive voltage regulator ICs
Table 25. DPAK and D²PAK tape and reel mechanical data
Tape
Reel
mm
mm
Dim.
Dim.
Min.
Max.
A0
6.8
7
A
B0
10.4
10.6
B
1.5
12.1
C
12.8
1.6
D
20.2
G
16.4
50
B1
54/58
Min.
Max.
330
13.2
D
1.5
D1
1.5
E
1.65
1.85
N
F
7.4
7.6
T
K0
2.55
2.75
P0
3.9
4.1
Base qty.
2500
P1
7.9
8.1
Bulk qty.
2500
P2
1.9
2.1
R
40
T
0.25
0.35
W
15.7
16.3
DocID2143 Rev 32
18.4
22.4
Positive voltage regulator ICs
10
Order codes
Order codes
Table 26. Order codes
Order codes
Part
numbers
L7805C
TO-220
TO-220
(single gauge)
(dual gauge)
L7805CV
DPAK
D²PAK
TO-220FP
Output
voltages
L7805CDT-TR
L7805CD2T-TR
L7805CP
5V
L7805CV-DG
L7805AB
5V
L7805ABV
L7805ABD2T-TR
L7805ABP
L7805ABV-DG
L7805AC
L7805ACV
5V
L7805ACD2T-TR
L7805ACP
L7805ACV-DG
L7806C
L7806CV
L7806CD2T-TR
6V
6V
L7806ABV
L7806ABD2T-TR
6V
L7806ABV-DG
L7806AC
6V
L7806ACV
6V
L7806ACV-DG
L7808C
L7808CV
6V
L7808CD2T-TR
8V
L7808CV-DG
L7808AB
8V
L7808ABV
L7808ABD2T-TR
8V
L7808ABV-DG
L7808AC
8V
L7808ACV
8V
L7808ACV-DG
L7885C
L7885CV
L7809C
L7809CV
8V
8.5 V
L7809CD2T-TR
L7809CP
L7809CV-DG
L7809AB
5V
5V
L7806CV-DG
L7806AB
5V
9V
9V
L7809ABV
L7809ABD2T-TR
9V
L7809ABV-DG
9V
L7809AC
L7809ACV
9V
L7812C
L7812CV
L7812CD2T-TR
L7812CV-DG
L7812AB
12 V
12 V
L7812ABV
L7812ABD2T-TR
L7812ABV-DG
L7812AC
L7812CP
L7812ACV
12 V
L7812ACD2T-TR
L7812ACV-DG
DocID2143 Rev 32
12 V
12 V
12 V
55/58
58
Order codes
Positive voltage regulator ICs
Table 26. Order codes (continued)
Order codes
Part
numbers
L7815C
TO-220
TO-220
(single gauge)
(dual gauge)
DPAK
L7815CV
D²PAK
TO-220FP
Output
voltages
L7815CD2T-TR
L7815CP
15 V
L7815CV-DG
L7815AB
15 V
L7815ABV
L7815ABD2T-TR
15 V
L7815ABV-DG
L7815AC
L7815ACV
15 V
L7815ACD2T-TR
15 V
L7815ACV-DG
L7818C
15 V
L7818CV
18 V
L7818CV-DG
L7824C
18 V
L7824CV
L7824CD2T-TR
L7824CV-DG
L7824AB
L7824ABV
24 V
L7824ACV
24 V
24 V
L7824ACV-DG
56/58
24 V
24 V
L7824ABV-DG
L7824AC
L7824CP
DocID2143 Rev 32
24 V
Positive voltage regulator ICs
11
Revision history
Revision history
Table 27. Document revision history
Date
Revision
21-Jun-2004
12
Document updating.
03-Aug-2006
13
Order codes has been updated and new template.
19-Jan-2007
14
D²PAK mechanical data has been updated and add footprint data.
31-May-2007
15
Order codes has been updated.
29-Aug-2007
16
Added Table 1 in cover page.
11-Dec-2007
17
Modified: Table 26.
06-Feb-2008
18
Added: TO-220 mechanical data Figure 38 on page 38 , Figure 39 on page 39,
and Table 23 on page 37. Modified: Table 26 on page 55.
18-Mar-2008
19
Added: Table 29: DPAK mechanical data on page 50, Table 30: Tape and reel
DPAK mechanical data on page 52. Modified: Table 26 on page 55.
26-Jan-2010
20
Modified Table 1 on page 1 and Table 23 on page 37, added: Figure 38 on
page 38 and Figure 39 on page 39, Figure 45 on page 52 and Figure 46 on
page 52.
04-Mar-2010
21
Added notes Figure 38 on page 38.
08-Sep-2010
22
Modified Table 26 on page 55.
23-Nov-2010
23
Added: TJ = 25 °C test condition in ΔVO on Table 3, 4, 5, 6, 7, 8 and Table 9.
16-Sep-2011
24
Modified title on page 1.
30-Nov-2011
25
Added: order codes L7805CV-DG, L7806CV-DG, L7808ABV-DG, L7812CV-DG
and L7815CV-DG Table 26 on page 55.
08-Feb-2012
26
Added: order codes L7805ACV-DG, L7805ABV-DG, L7806ABV-DG, L7808CVDG, L7809CV-DG, L7812ACV-DG, L7818CV-DG, L7824CV-DG Table 26 on
page 55.
27-Mar-2012
27
Added: order codes L7812ABV-DG, L7815ABV-DG Table 26 on page 55.
27-Apr-2012
28
Modified: VI = 10.4 to 23 V ==> VI = 11.4 to 23 V test conditon value
Line regulation Table 6 on page 12.
10-May-2012
29
Added: order codes L7806ACV-DG, L7808ACV-DG, L7815ACV-DG,
L7824ABV-DG and L7824ACV-DG Table 26 on page 55.
19-Sep-2012
30
Modified load regulation units from V to mV in Table 3 to Table 9.
12-Mar-2013
31
Modified: VO output voltage at 25 °C min. value 14.4 V Table 16 on page 22.
32
Part numbers L78xx, L78xxC, L78xxAB, L78xxAC changed to L78.
Removed TO-3 package.
Updated the description in cover page, Section 2: Pin configuration, Section 3:
Maximum ratings, Section 4: Test circuits, Section 5: Electrical characteristics,
Section 6: Application information, Section 8: Package mechanical data and
Table 26: Order codes.
Added Section 9: Packaging mechanical data.
Minor text changes.
04-Mar-2014
Changes
DocID2143 Rev 32
57/58
58
Positive voltage regulator ICs
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2014 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
58/58
DocID2143 Rev 32