ADS5120 SBAS247E – MARCH 2002 – REVISED NOVEMBER 2005 8-Channel, 10-Bit, 40MSPS, 1.8V CMOS ANALOG-TO-DIGITAL CONVERTER FEATURES DESCRIPTION ● 8 DIFFERENTIAL ANALOG INPUTS The ADS5120 is a low-power, 8-channel, 10-bit, 40MSPS CMOS Analog-to-Digital Converter (ADC) that operates from a single 1.8V supply, while offering 1.8V and 3.3V digital I/O flexibility. A single-ended input clock is used for simultaneous sampling of up to eight analog differential input channels. The flexible duty cycle adjust circuit (DCASEL) allows the use of a non-50% clock duty cycle. Individual standby pins allow users the ability to power-down any number of ADCs. A sample-andhold stage is added in front of the ADC and a digital error correction circuit is used to generate the final digital code. ● 1VPP DIFFERENTIAL INPUT RANGE ● INT/EXT VOLTAGE REFERENCE ● ANALOG/DIGITAL SUPPLY 1.8V ● DIGITAL I/O SUPPLY 1.8V/3.3V ● INTEGRAL NONLINEARITY: ±0.8LSB ● SIGNAL-TO-NOISE: 58dB at fIN = 20MHz ● SPURIOUS-FREE DYNAMIC RANGE: 72dB at fIN = 20MHz The internal reference can be bypassed to use an external reference to suit the accuracy and temperature drift requirements of the application. A 10-bit parallel bus on eight channels is provided with 3-state outputs. ● 794mW POWER DISSIPATION ● INDIVIDUAL CHANNEL POWER-DOWN ● 257-LEAD, 0.8 BALL PITCH, PLASTIC MicroSTAR BGA™ (16 • 16mm) The speed, resolution, and low-power of the ADS5120 makes it ideal for applications requiring high-density signal processing in low-power environments. APPLICATIONS The ADS5120 is characterized for operation from 0°C to 70°C. ● PORTABLE ULTRASOUND ● PORTABLE INSTRUMENTATION AVDD STBY (x8) OE DRVDD DVDD CLK AINA+ T&H 10-Bit ADC 3-State Output Buffers D[9:0]A T&H 10-Bit ADC 3-State Output Buffers D[9:0]H AINA– AINH– AINH+ Internal Reference Circuit IREFR CM DCASEL AGND BG PDREF REFT REFB CML DRVGND DGND Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. MicroSTAR BGA is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. Copyright © 2002-2005, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. www.ti.com ABSOLUTE MAXIMUM RATINGS(1) ELECTROSTATIC DISCHARGE SENSITIVITY Supply Voltage: AVDD to AGND, DVDD to DGND ............. –0.3V to +2.2V DRVDD to DGND ..................................... –0.3V to +4.0V AGND to DGND ...................................... –0.3V to +0.3V AVDD to DVDD .......................................... –2.2V to +2.2V Reference Voltage Input Range REFT, REFB to AGND ... –0.3V to AVDD + 0.3V Analog Input Voltage Range AIN to AGND ........... –0.3V to AVDD + 0.3V Clock Input CLK to DGND .................................. –0.3V to DRVDD + 0.3V Digital Input to DGND ........................................... –0.3V to DVDD + 0.3V Digital Outputs to DRGND .................................. –0.3V to DRVDD + 0.3V Operating Temperature Range (TJ) ................................... 0°C to +105°C Storage Temperature Range (TSTG) ................................. –65°C + 150°C This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. NOTE: (1) Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to absolute maximum conditions for extended periods may affect device reliability. PACKAGE/ORDERING INFORMATION(1) PACKAGE-LEAD PACKAGE DESIGNATOR SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER TRANSPORT MEDIA, QUANTITY ADS5120 MicroSTAR BGA-257 GHK 0°C to +70°C ADS5120CGHK ADS5120CGHK Tray, 90 ADS5120 ROHS-Compliant Microstar ZHK 0°C to +70°C ADS5120CZHK ADS5120CZHK Tray, 90 PRODUCT NOTE: (1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. BLOCK DIAGRAM STBY (x8) AVDD OE DRVDD DVDD CLK AINA+ T&H 10-Bit ADC 3-State Output Buffers D[9:0]A T&H 10-Bit ADC 3-State Output Buffers D[9:0]B T&H 10-Bit ADC 3-State Output Buffers D[9:0]C T&H 10-Bit ADC 3-State Output Buffers D[9:0]D T&H 10-Bit ADC 3-State Output Buffers D[9:0]E T&H 10-Bit ADC 3-State Output Buffers D[9:0]F T&H 10-Bit ADC 3-State Output Buffers D[9:0]G T&H 10-Bit ADC 3-State Output Buffers D[9:0]H AINA– AINB– AINB+ AINC+ AINC– AIND– AIND+ AINE+ AINE– AINF– AINF+ AING+ AING– AINH– AINH+ Internal Reference Circuit IREFR CM DCASEL AGND 2 BG PDREF REFT REFB CML DRVGND DGND ADS5120 www.ti.com SBAS247E DC CHARACTERISTICS AVDD = DVDD = 1.8V, DRVDD = 3.3V, Clock = 40MSPS, 50% Clock Duty Cycle, –0.5dBFS Input Span, Internal Reference, TMIN = 0°C, and TMAX = +70°C, unless otherwise noted. ADS5120 PARAMETER CONDITION MIN TYP RESOLUTION 10 DC ACCURACY Differential Nonlinearity (DNL) Integral Nonlinearity (INL) No Missing Codes Gain Error Offset Error Gain Temperature Coefficient Gain Matching External Reference External Reference REFB EXTERNAL REFERENCE GENERATION Reference, Top (REFT) Reference, Bottom (REFB) Input Resistance, REFRIN (between REFB and REFT) +1.0 +1.5 LSB LSB +1.0 +1.8 %FSR %FSR ppm/°C %FSR REFT V VPP V kΩ pF 1 (REFT + REFB)/ 2 83 5 fCLK = 40MSPS INTERNAL REFERENCE VOLTAGES Reference, Top (REFT) Reference, Bottom (REFB) Int Reference Temperature Coefficient PSRR, Power-Supply Rejection Ratio –1.0 UNITS Bits ±0.4 ±0.8 Tested 0.1 0.2 80 ±0.4 –0.9 –1.5 ANALOG INPUT Input Voltage Range (AIN+, AIN–) Input Voltage, Differential Full-Scale Input Common-Mode Range Input Resistance, RIN Input Capacitance, CIN POWER SUPPLY Operating Supply Current, IDD Analog Operating Supply Current, IAVDD Digital Operating Supply Current, IDVDD Driver Operating Supply Current, IDRVDD Operating Voltage AVDD DVDD DRVDD Power Dissipation Standby Power (STBY) MAX 1.30 0.76 1.34 0.81 50 1.40 0.85 V V ppm/°C 1.15 0.65 1.25 0.75 80 1.35 0.85 V V Ω 398 294 44 53 450 340 49 60 mA mA mA mA 1.8 1.8 1.8 794 68 60 10 2.5 0.8 2.0 2.0 3.6 850 V V V mW mW mW mW mW mV/V fIN = 3.5MHz CL = 20pF 1.65 1.65 1.65 CLK Running CLK Stopped PDREF = 1, External REF, CLK Running PDREF = 1, External REF, CLK Stopped ±5% 15 5 DC CHARACTERISTICS AVDD = DVDD = 1.8V, DRVDD = 3.3V, Clock = 40MSPS, 50% Clock Duty Cycle, –0.5dBFS Input Span, Internal Reference, and TMIN to TMAX, unless otherwise noted. ADS5120 PARAMETER DIGITAL INPUTS (STBY A-H, PDREF, OE, CLK) High-Level Input Voltage, VIH Low-Level Input Voltage, VIL High-Level Input Current, IIH Low-Level Input Current, IIL DIGITAL INPUTS (DCASEL) High-Level Input Voltage, VIH Low-Level Input Voltage, VIL High-Level Input Current, IIH Low-Level Input Current, IIL DIGITAL OUTPUTS ( DRVDD = 3.3/1.8V) High-Level Output Voltage, VOH Low-Level Output Voltage, VOL External Load Capacitance, CL 3-State Leakage Current, ILEAK CONDITION MIN DRVDD = 3.3V/1.8V VIH = DRVDD VIL = 0V 0.70 • DRVDD VIH = DVDD VIL = 0V 0.70 • DVDD IOH = –50µA IOL = 50µA 0.8 • DRVDD MAX UNITS 0.25 • DRVDD ±1 ±1 V V µA µA 0.25 • DVDD ±1 ±1 V V µA µA 0.2 • DRVDD 15 OE = HIGH ADS5120 SBAS247E TYP www.ti.com ±1 V V pF µA 3 TARGETED AC CHARACTERISTICS AVDD = DVDD = 1.8V, DRVDD = 3.3V, 50% Clock Duty Cycle, CLK = 40MSPS, Analog input at –0.5dBFS Input Span, Internal voltage reference, TMIN = 0°C, TMAX = 70°C, and typical values are at TA = 25°C, unless otherwise noted. ADS5120 PARAMETER CONDITION Signal-to-Noise Ratio (SNR) MIN (SINAD) (ENOB) Spurious-Free Dynamic Range (SFDR) 55 58 dB 55 58 dB 58 dB fIN = 3.5MHz 55 57 dB fIN = 10MHz 55 57 dB 57 dB fIN = 3.5MHz 8.8 9.2 Bits Bits fIN = 10MHz 8.8 9.2 fIN = 20MHz 8.8 9.2 Bits fIN = 3.5MHz 65 73 dBc fIN = 10MHz 65 72 dBc 72 dBc fIN = 20MHz 2nd-Harmonic Distortion (HD2) fIN = 3.5MHz 68 79 dBc fIN = 10MHz 68 80 dBc 80 dBc fIN = 20MHz 3rd-Harmonic Distortion (HD3) 2-Tone Intermodulation Distortion (IMD) UNITS fIN = 10MHz fIN = 20MHz Effective Number of Bits MAX fIN = 3.5MHz fIN = 20MHz Signal-to-Noise and Distortion TYP fIN = 3.5MHz 65 76 dBc fIN = 10MHz 65 78 dBc fIN = 20MHz 73 dBc f1 = 4.43MHz, f2 = 4.53MHz at –6.5dB –69 dBFS Channel-to-Channel Crosstalk fIN = 10MHz, DRVDD = 3.3V 89 dB 300 MHz Over-Voltage Recovery Time(1) 20 ns Differential Gain(1) ±1 % ±0.25 Degree Large-Signal Bandwidth (FPBW) Differential Phase(1) NOTE: (1) Assured by design. SWITCHING CHARACTERISTICS AVDD = DVDD = 1.8V, DRVDD = 3.3V, 50% Clock Duty Cycle, CLK = 40MSPS, Analog input at –0.5dBFS Input Span, Internal voltage reference, TMIN = 0°C, and TMAX = 70°C. Typical values are at TA = 25°C, unless otherwise noted. ADS5120 PARAMETER CONDITION Maximum Conversion Rate Clock Duty Cycle Data Latency(1) Clock ↓ to Data Valid OE ↓ to Outputs Enabled OE ↑ Rising to Outputs Tri-Stated Aperture Delay Aperture Uncertainty (Jitter) MIN TYP 1 DCASEL Enabled 30 to 70 7 8 8 8 1 2 tDO(1) tEN(1) tDIS MAX UNITS 40 MSPS % Clk Cycles ns ns ns ns ps, r ms 10 NOTE: (1) See Timing Diagram. TIMING DIAGRAM (Per ADC Channel) Sample 2 Sample 1 Analog Input CLK 1 2 3 4 5 6 7 8 9 10 OE tEN D[9:0] 4 tDIS tDO S–7 S–6 S–5 S–4 S–3 S–2 S–1 S1 S2 ADS5120 www.ti.com SBAS247E PIN CONFIGURATION 14,40 TYP Bottom View BGA 0,80 0,80 W V U T R P N M L K J H G F E D C B A 3 1 2 5 4 7 6 9 8 11 10 13 12 15 14 17 16 19 18 PIN DESCRIPTIONS NAME PINS I/O AVDD AGND I I Analog Supply, (1.8V) Analog Ground AINA+ AINA– AINB+ AINB– AINC+ AINC– AIND+ AIND– AINE+ AINE– AINF+ AINF– AING+ AING– AINH+ AINH– CLK REFT REFB CML BG C6, C7, E6, F1, F2, F3, F5, F6, J6, N3, P3, P5, P6, P7, R6, V6, W6 A3, A5, B5, B9, C1, C5, C9, E3, E7, F7, G1, G5, G6, H6, J1, J2, M2, N5, N6, P8, R1, R2, R3, R7, U1, U5, U10, V5, V10, W3, W7 U7 V7 W4 V4 T1 T2 P2 P1 G3 G2 D1 D2 A4 B4 B6 A6 W9 K3, L1, J3 K5, J5, L5 L2, L3 K1 I I I I I I I I I I I I I I I I I/O I/O O I/O IREFR K6 I DNC DNC NC DCASEL DVDD I I I I I I Digital Ground PDREF W5 U6 E1, E2, E5, K2, L6, M1 N2 C2, C3, C4, D3, E8, F8, H3, H5, M3, M5, R8, T3, U3, U4, U8, V3, P13, R13 P17, L15, J14, F17, F12, E12 A2, A7, B1, B2, B3, B7, B13, C13, G15, H1, H2, H17, L17, M6, N1, N15, U2, U13, U14, V1, V2, V8, W2, W8 V9 Analog Input Channel A Complementary Analog Input Channel A Analog Input Channel B Complementary Analog Input Channel B Analog Input Channel C Complementary Analog Input Channel C Analog Input Channel D Complementary Analog Input Channel D Analog Input Channel E Complementary Analog Input Channel E Analog Input Channel F Complementary Analog Input Channel F Analog Input Channel G Complementary Analog Input Channel G Analog Input Channel H Complementary Analog Input Channel H Clock Input Reference Top Reference Bottom Common-Mode Level Output Bandgap Decoupling (Decouple with 1µF cap to AGND and 100kΩ to AVDD) Internal Reference Bias Current (Connect 6.19kΩ resistor from this pin AGND to set internal bias amplifier current.) Do Not Connect Do Not Connect No Internal Connection Duty Cycle Adjust Digital Supply (1.8V) I STBY A STBY B STBY C STBY D STBY E STBY F STBY G STBY H OE W10 P9 R9 U9 C8 B8 A8 A9 P10 I I I I I I I I I DRVDD B17, C16, D17, E9, E10, E11, E17, F9, H14, H15, K17, L14, N14, P12, P14, P15 R10, R12, R14 E13, F10, F11, F13, F14, F15, G14, G17, M14, M15, M17, N17, U11, U12, U15, U16 I I I Power-Down Ref: 0 = internal reference, 1 = external reference. In external reference mode connect REFT to BG pin. Power-Down Channel A Power-Down Channel B Power-Down Channel C Power-Down Channel D Power-Down Channel E Power-Down Channel F Power-Down Channel G Power-Down Channel H Enable all Digital Outputs, Ch A-H. OE: 0 = Outputs Enable. OE: 1 = Outputs disabled (3-State). Driver Digital Supply (1.8V or 3.3V) DGND DRGND ADS5120 SBAS247E www.ti.com TERMINAL DESCRIPTION Driver Digital Ground 5 DATA OUTPUT PINS NAME PINS I/O TERMINAL DESCRIPTION D0A D1A D2A D3A D4A D5A D6A D7A D8A D9A D0B D1B D2B D3B D4B D5B D6B D7B D8B D9B D0C D1C D2C D3C D4C D5C D6C D7C D8C D9C D0D D1D D2D D3D D4D D5D D6D D7D D8D D9D V14 W14 V13 W13 V12 W12 R11 P11 V11 W11 V19 V18 U17 W18 V17 W17 V16 W16 V15 W15 P19 P18 R19 R18 R17 T19 T18 U19 U18 T17 K14 K15 K18 K19 L18 L19 M19 M18 N19 N18 O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O Bit 1, Channel A (LSB) Bit 2, Channel A Bit 3, Channel A Bit 4, Channel A Bit 5, Channel A Bit 6, Channel A Bit 7, Channel A Bit 8, Channel A Bit 9, Channel A Bit 10, Channel A (MSB) Bit 1, Channel B (LSB) Bit 2, Channel B Bit 3, Channel B Bit 4, Channel B Bit 5, Channel B Bit 6, Channel B Bit 7, Channel B Bit 8, Channel B Bit 9, Channel B Bit 10, Channel B (MSB) Bit 1, Channel C (LSB) Bit 2, Channel C Bit 3, Channel C Bit 4, Channel C Bit 5, Channel C Bit 6, Channel C Bit 7, Channel C Bit 8, Channel C Bit 9, Channel C Bit 10, Channel C (MSB) Bit 1, Channel D (LSB) Bit 2, Channel D Bit 3, Channel D Bit 4, Channel D Bit 5, Channel D Bit 6, Channel D Bit 7, Channel D Bit 8, Channel D Bit 9, Channel D Bit 10, Channel D (MSB) 6 NAME D0E D1E D2E D3E D4E D5E D6E D7E D8E D9E D0F D1F D2F D3F D4F D5F D6F D7F D8F D9F D0G D1G D2G D3G D4G D5G D6G D7G D8G D9G D0H D1H D2H D3H D4H D5H D6H D7H D8H D9H PINS F18 F19 G18 G19 H18 H19 J15 J17 J18 J19 A18 B18 C17 B19 C18 C19 D18 D19 E18 E19 A14 B14 C14 A15 B15 E14 C15 A16 B16 A17 C10 B10 A10 C11 B11 A11 A12 B12 C12 A13 I/O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O TERMINAL DESCRIPTION Bit 1, Channel E (LSB) Bit 2, Channel E Bit 3, Channel E Bit 4, Channel E Bit 5, Channel E Bit 6, Channel E Bit 7, Channel E Bit 8, Channel E Bit 9, Channel E Bit 10, Channel E (MSB) Bit 1, Channel F (LSB) Bit 2, Channel F Bit 3, Channel F Bit 4, Channel F Bit 5, Channel F Bit 6, Channel F Bit 7, Channel F Bit 8, Channel F Bit 9, Channel F Bit 10, Channel F (MSB) Bit 1, Channel G (LSB) Bit 2, Channel G Bit 3, Channel G Bit 4, Channel G Bit 5, Channel G Bit 6, Channel G Bit 7, Channel G Bit 8, Channel G Bit 9, Channel G Bit 10, Channel G (MSB) Bit 1, Channel H (LSB) Bit 2, Channel H Bit 3, Channel H Bit 4, Channel H Bit 5, Channel H Bit 6, Channel H Bit 7, Channel H Bit 8, Channel H Bit 9, Channel H Bit 10, Channel H (MSB) ADS5120 www.ti.com SBAS247E TYPICAL CHARACTERISTICS TA = 25°C, AVDD = DVDD = 1.8V, DRVDD = 3.3V, fIN = –0.5dBFS, Internal Reference, Clock = 40MSPS, and Differential Input Range = 1VPP, unless otherwise noted. SPECTRAL PERFORMANCE SPECTRAL PERFORMANCE 0 0 fIN = 9.8MHz –20 –40 –40 Amplitude (dB) Amplitude (dB) fIN = 3.5MHz –20 –60 –80 –100 –60 –80 –100 –120 –120 0 5 10 15 20 0 5 Frequency (MHz) 15 20 DIFFERENTIAL NONLINEARITY SPECTRAL PERFORMANCE 1 0 fIN = 19.5MHz 0.8 –20 0.6 0.4 –40 DNL (LSB) Amplitude (dB) 10 Frequency (MHz) –60 –80 0.2 0 –0.2 –0.4 –0.6 –100 –0.8 –1 –120 0 5 10 15 0 20 256 768 1024 2ND- AND 3RD-HARMONIC vs INPUT FREQUENCY INTEGRAL NONLINEARITY 88 0.8 86 2nd- and 3rd-Harmonic (dBc) 1 0.6 0.4 INL (LSB) 512 Input Codes Frequency (MHz) 0.2 0 –0.2 –0.4 –0.6 –0.8 3rd 84 82 80 78 2nd 76 74 72 –1 0 256 512 768 1024 Input Codes ADS5120 SBAS247E www.ti.com 0 5 10 15 Input Frequency (MHz) 20 7 TYPICAL CHARACTERISTICS (Cont.) TA = 25°C, AVDD = DVDD = 1.8V, DRVDD = 3.3V, fIN = –0.5dBFS, Internal Reference, Clock = 40MSPS, and Differential Input Range = 1VPP, unless otherwise noted. SNR AND SFDR vs CLOCK FREQUENCY SNR AND SFDR vs CLOCK FREQUENCY 85 85 fIN = 3.5MHz fIN = 10MHz 80 SFDR SNR (dB), SFDR (dBc) SNR (dB), SFDR (dBc) 80 75 70 65 SNR 60 55 SFDR 75 70 65 SNR 60 55 50 50 5 10 15 20 25 30 35 40 45 5 10 15 Clock Frequency (MHz) 20 25 30 35 40 45 Clock Frequency (MHz) SINAD vs DUTY CYCLE (DCASEL = ENABLE) SNR vs INPUT FREQUENCY 60 60 fIN = 3.5MHz 59 59 58 56 SNR (dB) SINAD (dB) 57 55 54 58 57 53 56 52 51 55 50 20 30 40 50 0 70 60 4 8 12 20 16 Input Frequency (MHz) Clock Duty Cycle (%) IAVDD vs CLOCK FREQUENCY SWEPT INPUT POWER (SNR) 305 70 60 dBFS IAVDD (mA) SNR (dBFS, dBc) 300 50 40 dBc 30 295 290 20 285 10 0 280 –45 –40 –35 –30 –25 –20 –15 –10 –5 0 0 8 5 10 15 20 25 30 35 40 Clock Frequency (MSPS) Input Amplitude (dBFS) ADS5120 www.ti.com SBAS247E TYPICAL CHARACTERISTICS (Cont.) TA = 25°C, AVDD = DVDD = 1.8V, DRVDD = 3.3V, fIN = –0.5dBFS, Internal Reference, Clock = 40MSPS, and Differential Input Range = 1VPP, unless otherwise noted. IDVDD vs CLOCK FREQUENCY IDRVDD vs CLOCK FREQUENCY 50 60 45 50 40 IDRVDD (mA) IDVDD (mA) 35 30 25 20 15 10 40 30 20 10 5 0 0 0 5 10 15 20 25 30 35 40 0 5 10 Clock Frequency (MSPS) TOTAL POWER vs CLOCK FREQUENCY 20 25 30 35 40 60 70 POWER vs TEMPERATURE 850 805 800 800 Power (mW) 750 Power (mW) 15 Clock Frequency (MSPS) 700 650 600 795 790 785 780 550 500 775 0 5 10 15 20 25 30 35 40 0 10 20 25 Clock Frequency of CLK (MSPS) 30 40 50 Temperature (°C) GAIN ERROR vs TEMPERATURE 0.6 Ch-A Gain Error (% Full-Scale) 0.5 0.4 Ch-H Ch-C 0.3 0.2 Ch-G Ch-E 0.1 0 Ch-B Ch-D Ch-F –0.1 –0.2 0 10 20 25 30 40 50 60 70 Temperature (°C) ADS5120 SBAS247E www.ti.com 9 APPLICATION INFORMATION CONVERTER OPERATION The ADS5120 is an 8-channel, simultaneous sampling ADC. Its low power (100mW/channel) and high sampling rate of 40MSPS is achieved using a state-of-the-art switched capacitor pipeline architecture built on an advanced low-voltage CMOS process. The ADS5120 primarily operates from a +1.8V single supply. For additional interfacing flexibility, the digital I/O supply (DRVDD) can be set to either +1.8V or +3.3V. The ADC core of each channel consists of 10 pipeline stages. Each of the 10 stages produces one digital bit per stage. Both the rising and the falling clock edges are utilized to propagate the sample through the pipeline every half clock, for a total of five clock cycles. Two additional clock cycles are needed to pass the sample data through the digital error correction logic and the output latches. The total pipeline delay, or data latency, is therefore seven clock cycles long. Since a common clock controls the timing of all eight channels, the analog signal is sampled at the same time, as well as the data on the parallel ports which becomes updated simultaneously. ANALOG INPUTS The analog input for each channel of the ADS5120 consists of a differential track-and-hold amplifier implemented using a switched capacitor technique, shown in Figure 1. This differential input topology along with closely matched capacitors produces a high level of AC performance up to high sampling rates. slew current to charge and discharge the input sampling capacitor while the track-and-hold amplifier is in track mode. The input impedance of the ADS5120 is also a function of the sampling rate. As the sampling frequency increases, the input impedance decreases linearly at a rate of 1/fs. For most applications, this does not represent a limitation since the impedance remains relatively high, for example, approximately 83kΩ at the max sampling rate of 40MSPS. For applications using an op amp to drive the ADC, it is recommended that a series resistor, typically 10Ω to 50Ω, be added between the amplifier output and the converter inputs. This will isolate the converter capacitive input from the driver and avoid potential gain peaking, or instability. INPUT BIASING The ADS5120 operates from a single +1.8V analog supply, and requires each of the analog inputs (AIN+, AIN–) to be externally biased by a suitable common-mode voltage. For example, with a common-mode voltage of +1V, the 1VPP fullscale, differential input signal will swing symmetrically around +1V, or between 0.75V and 1.25V. This is determined by the two reference voltages, the top reference (REFT), and the bottom reference (REFB). Typically, the input common-mode level is related to the reference voltages and defined as (REFT + REFB)/2. This reference mid-point is provided at the CML pin and can directly be used for input biasing purposes. The voltage at CML will assume the mid-point for either internal or external reference operation. In any case, it is recommended to bypass the CML pin with a ceramic 0.1µF capacitor. DRIVING THE ANALOG INPUTS Differential versus Single-Ended ADS5120 S5 The analog input of the ADS5120 allows it to be driven either single-ended or differentially. Differential operation of the ADS5120 requires an input signal that consists of an inphase and a 180° out-of-phase part simultaneously applied to the inputs (AIN+, AIN–). The full-scale input range of the ADS5120 is defined by the reference voltages according to FSR = 2 x (REFT – REFB). For a typical 1VPP range, the differential input configuration only requires each input to see a signal swing of 0.5VPP. Operating the converter in singleended configuration requires the full 1VPP swing applied to the chosen input. The differential operation offers a number of advantages, which in most applications will be instrumental in achieving the best dynamic performance of the ADS5120: S3 VBIAS S1 CIN S2 CIN AIN+ T&H AIN– S4 VBIAS S6 Tracking Phase: S1, S2, S3, S4 closed; S5, S6 open. Hold Phase: • The signal swing is half of that required for the singleended operation and is therefore less demanding to achieve while maintaining good linearity performance from the signal source. S1, S2, S3, S4 open; S5, S6 closed. FIGURE 1. Simplified Circuit of Input Track-and-Hold. • The reduced signal swing allows for more headroom of the interface circuitry and therefore a wider selection of the best suitable driver op amp. INPUT IMPEDANCE Because of the switched capacitor input track-and-hold amplifier, the input impedance of the ADS5120 is effectively capacitive, and the driving source needs to provide sufficient 10 • Even-order harmonics are minimized. • Improves the noise immunity based on the converter’s common-mode input rejection. ADS5120 www.ti.com SBAS247E For the single-ended mode, the signal is applied to one of the inputs while the other input is biased with a DC voltage to the required common-mode level. Both inputs are identical in terms of their impedance and performance. Applying the signal to the complementary input (AIN–) instead of the AIN+ input, however, will invert the orientation of the input signal relative to the output code. This could be helpful, for example, if the input driver operates in inverting mode using input AIN– as the signal input will restore the phase of the signal to its original orientation. INPUT DRIVER CONFIGURATIONS Transformer-Coupled Interface If the application requires a signal conversion from a singleended source to drive the ADS5120 differentially, an RFtransformer might be a good solution. The selected transformer must have a center tap in order to apply the commonmode DC voltage necessary to bias the converter inputs. ACgrounding the center tap will generate the differential signal swing across the secondary winding. Consider a step-up transformer to take advantage of signal amplification without the introduction of another noise source. Furthermore, the reduced signal swing from the source may lead to an improved distortion performance. The differential input configuration may provide a noticeable advantage of achieving good SFDR performance over a wide range of input frequencies. In this mode, both inputs (AIN+ and AIN–) of the ADS5120 see matched impedances. Figure 2 shows the schematic for the suggested transformercoupled interface circuit. The component values of the R-C low-pass may be optimized depending on the desired roll-off frequency. Single-Ended, AC-Coupled Driver The circuit of Figure 3 shows an example for driving the inputs of the ADS5120 in a single-ended configuration. The signal is AC-coupled between the driver amplifier and the converter input (AIN+). This allows for setting the required common-mode voltages for the ADC and op amp separately. The single-supply op amp is biased at mid-supply by two resistors connected at its noninverting input. Connecting each input to the CML pin provides the required commonmode voltage for the inputs of the ADS5120. Here, two resistors of equal value ensure that the inputs see closely matched source impedances. If the op amp features a disable function, it could be easily tied together with the power-down pin of the ADS5120 channel (STBY). In the circuit example depicted in Figure 3, the OPA355 EN pin is +5V –5V RS VIN 0.1µF OPA690 RIN 1:n AIN+ RT R1 CIN RIN ADS5120 AIN– CML R2 0.1µF FIGURE 2. Converting a Single-Ended Input Signal into a Differential Signal Using an RF-Transformer. +3V/+5V R1 0.1µF VIN EN RS 24Ω STBY 0.1µF AIN+ OPA355 R2 18pF ADS5120 RF 604Ω 1.82kΩ AIN– 1.82kΩ RG 604Ω CML 0.1µF 0.1µF FIGURE 3. Single-Ended, AC-Coupled Driver Configuration for Single Supply. ADS5120 SBAS247E www.ti.com 11 IREFR pin to analog ground, AGND (as shown in Figure 5). While a 1% resistor tolerance is adequate, deviating from this resistor value will cause altered and degraded performance. directly connected to the STBY pin to allow for a power-down mode of the entire circuit. Other suitable op amps for singlesupply driver applications include the OPA634, OPA635, or OPA690, for example. To ensure proper operation with any reference configuration, it is necessary to provide solid bypassing at all reference pins in order to keep the clock feedthrough to a minimum. Figure 5 shows the recommended decoupling scheme. Good performance can be obtained using 0.1µF low inductance ceramic capacitors. Adding tantalum capacitors (1µF to 10µF) may lead to a performance improvement, depending on the application. All bypassing capacitors should be located as close to their respective pins as possible. DC-Coupled Interface with Differential Amplifier Differential input/output amplifiers can simplify the driver circuit for applications requiring input DC-coupling. Flexible in their configurations, such amplifiers can be used for singleended to differential conversion, allow for signal amplification, and also filtering prior to the ADC. Figure 4 shows one possible circuit implementation using the THS4130 amplifier. Here, the amplifier operates with a gain of +1. The commonmode voltage available at the CML pin can be conveniently connected to the amplifier VOCM pin to set the required input bias for the ADS5120. INTERNAL REFERENCE The internal reference circuit of the ADS5120 consists of a bandgap voltage reference, the drivers for the top and bottom reference, and the resistive reference ladder. The corresponding reference pins are REFT, REFB, CML, IREFR, BG, and PDREF. In order to enable the internal reference, REFERENCE OPERATION For proper operation of the ADS5120 and its reference, an external 6.19kΩ resistor must be connected from the 390Ω ADS5120 390Ω 20Ω VIN+ AIN+ VOCM THS4130 20Ω 18pF 390Ω AIN– 390Ω CML 0.1µF 2.2µF FIGURE 4. DC-Coupled Interface Using Differential I/O Amplifier THS4130. +1.8V PDREF AVDD 100kΩ ADS5120 BG REFT 1µF 0.1µF CML + 2.2µF REFB 0.1µF 0.1µF IREFR + 6.19kΩ 2.2µF FIGURE 5. Internal Reference; Recommended Configuration and Bypassing. 12 ADS5120 www.ti.com SBAS247E obtaining better matching of the full-scale range between converters. pin PDREF must be at a logic LOW = 0 level. In addition, the bandgap pin BG must have a 100kΩ pull-up resistor to AVDD, and should be decoupled with a 1µF capacitor. The reference circuit provides the reference voltages to each of the eight channels. Setting the ADS5120 for external reference mode requires taking the PDREF pin HIGH. In addition, pins BG and REFT must be connected together (as shown in Figure 6). The common-mode voltage at the CML pin will be maintained at approximately the mid-point of the applied reference voltages, according to CML ≈ (VREFT – VREFB)/2. The internal buffer amplifiers for REFT and REFB are disabled when the ADS5120 operates in the external reference mode. The external reference circuit must be designed to drive the internal reference ladder (80Ω) located between the REFT and REFB pins. For example, setting REFT = +1.25V and REFB = +0.75V will require a current drive capability of at least 0.5V/ 80Ω = 6.25mA. The external references can vary as long as the value of the external top reference (REFTEXT) stays within the range of +1.15V to +1.35V, and the external bottom reference (REFBEXT) stays within +0.65V to +0.85V (as shown in Figure 7). The reference buffers can be utilized to supply up to 1mA (sink and source) to an external circuitry. The common-mode level output pin, CML, represents the mid-point of the internal resistor ladder and is an unbuffered node. Loading of this pin should be avoided, as it will lead to degradation of the converter linearity. USING EXTERNAL REFERENCES For even more design flexibility, the internal reference can be disabled and an external reference voltage used. The utilization of an external reference may be considered for applications, requiring higher accuracy or improved temperature performance. Especially in multi-channel applications, the use of a common external reference has the benefit of AVDD +1.8V PDREF DRVDD ADS5120 BG CML REFT + 0.1µF 2.2µF REFB 0.1µF IREFR + 0.1µF 6.19kΩ 2.2µF REFBEXT REFTEXT FIGURE 6. External Reference; Recommended Configuration and Bypassing. +5V +5V 1/2 OPA2234 4.7kΩ REFT + R3 + 0.1µF ADS5120 R4 R1 REF1004 +2.5V 2.2µF 10µF 1/2 OPA2234 R2 REFB + 0.1µF 2.2µF 0.1µF FIGURE 7. Circuit Example of an External Reference Circuit Using Single-Supply, Low-Power, Dual Op Amp (OPA2234). ADS5120 SBAS247E www.ti.com 13 DIGITAL INPUTS AND OUTPUTS Clock Input DIFFERENTIAL INPUT The clock input is designed to operate with +1.8V or +3.3V CMOS logic levels. The clock circuitry is internally connected to the DRVDD supply. Therefore, the input HIGH and LOW levels will vary depending on the applied DRVDD supply; see DC Characteristics tables. Since both edges of the clock are used in this pipeline ADC, the ideal clock should be a squarewave logic signal with a 50% duty-cycle. Since this condition cannot always easily be met, the ADS5120 features an internal clock conditioning circuitry that can be activated through the duty-cycle adjust pin (DCASEL). The DCASEL pin is a logic input, with its logic levels related to the DVDD supply (+1.8V only): a) DCASEL = LOW (GND); in this mode the clock conditioning circuitry is disabled. Use this setting if the applied clock signal is a square-wave clock with a duty cycle of 50%; or if the duty cycle stays within a range of 48% to 52%. b) DCASEL = HIGH (DVDD); in this mode the clock conditioning circuitry is enabled. Use this setting if the applied external clock signal is a square-wave clock that does not meet the criteria listed above, but has a duty cycle in the range of 30% to 70%. MINIMUM SAMPLING RATE The pipeline architecture of the ADS5120 uses a switched capacitor technique for the internal track-and-hold stages. With each clock cycle, charges representing the captured signal level are moved within the ADC pipeline core. The high sampling rate necessitates the use of very small capacitor values. In order to hold the droop errors low, the capacitors require a minimum refresh rate. To maintain full accuracy of the acquired sample charge, the sampling clock of the ADS5120 should not be lower than the specified minimum of 1MSPS. DATA OUTPUT FORMAT The output data format of the ADS5120 is a positive Straight Offset Binary (SOB) code. Tables I and II show output coding of a single-ended and differential signal. For all data output channels, the MSBs are located at the D9x pins. SINGLE-ENDED INPUT (AIN– = CML) STRAIGHT OFFSET BINARY (SOB) +FS – 1LSB (AIN+ = CML + FSR/2) 11 1111 1111 +1/2 FS 11 0000 0000 Bipolar Zero (AIN+ = CML) 10 0000 0000 –1/2 FS 01 0000 0000 –FS (AIN+ = CML – FSR/2) 00 0000 0000 STRAIGHT OFFSET BINARY (SOB) +FS – 1LSB (AIN+ = REFT, AIN– = REFB) 11 1111 1111 +1/2 FS 11 0000 0000 Bipolar Zero (AIN+ = AIN– = CML) 10 0000 0000 –1/2 FS 01 0000 0000 –FS (AIN+ = REFB, AIN– = REFT) 00 0000 0000 TABLE II. Coding Table for Differential Input Configuration and 1VPP Full-Scale Range. DIGITAL OUTPUT LOADING Minimizing the capacitive loading on the digital outputs is very important in achieving the best performance. The total load capacitance is typically made up of two sources: the next stage input capacitance and the parasitic/printed circuit board (PDB) capacitance. It is recommended to keep the total capacitive loading on the data lines as low as possible (≤ 15pF). Higher capacitive loading will cause larger dynamic currents as the digital outputs are changing states. High current surges may cause feedback into the analog portion of the ADS5120 and affect the performance. If necessary, external buffers or latches close to the converter output pins may be used to minimize the capacitive loading. A suggested device is the SN74AVC16827 (20-bit buffer/driver), a member of the Advanced Very Low Voltage CMOS logic family (AVC). Using such a logic device can also provide the added benefit of isolating the ADS5120 from any digital noise activities on the bus coupling back high-frequency noise. Some applications may also benefit from the use of series resistors (≤ 100Ω) in the data lines. This will provide a current limit and reduce any existing over- or undershoot. OUTPUT ENABLE The ADS5120 provides one output enable pin (OE) that controls the digital outputs of all channels simultaneously. A LOW (L = 0) level on the OE pin will have all channels active and the converter in normal operation. Taking the OE pin HIGH (H = 1) will disable or tri-state the outputs of all channels. Note that the OE pin has no internal pull-up resistor and therefore requires a defined potential to be applied. The timing relations between OE and the output bus enable/disable times are shown in the Timing Diagram. POWER-UP SEQUENCE Ideally, the three main power supplies for the ADS5120 should be applied and ramped up simultaneously. If this cannot be ensured, the following power-up sequence is recommended: TABLE I. Coding Table for Single-Ended Input Configuration with Input AIN– Tied to the Common-Mode Voltage (CML). 1. AVDD (+1.8 typ) 2. DVDD (+1.8 typ) 3. DRVDD (+3.3 typ) The clock signal should also be applied with proper logic levels during power-up of the ADS5120. Deviating from this power-up sequence may cause the device to enter a mode such that the digital outputs do not approach the full specified output levels. 14 ADS5120 www.ti.com SBAS247E POWER-DOWN (STANDBY) The ADS5120 is equipped with a power-down function for each of the eight channels. Labeled as STBY pins, the normal operational mode is when this pin is connected to logic high (H = 1). The selected ADC channel will be in a power-down mode if the corresponding STBY pin is connected to logic LOW (L = 0). The logic levels for the STBY pins are dependent on the DRVDD supply. The power-down function controls internal biasing nodes, and as a consequence, any data present in the pipeline of the converter will become invalid. This is independent of whether the clock remains applied during power-down, or not. Following a power-up, new, valid data will become available after a minimum of seven clock cycles. As a note, the operation of the STBY pins is not intended for the use of dynamically multiplexing between the eight channels of the ADS5120. DIGITAL OUTPUT DRIVER SUPPLY, DRVDD The ADS5120 uses a dedicated supply connection for the output logic drivers, DRVDD, along with its digital driver ground connections, labeled DRGND. Setting the voltage at DRVDD to either +3.3V or +1.8V the output logic levels are set accordingly, allowing the ADS5120 to directly interface to a selected logic family. The output stages are designed to supply sufficient current to drive a variety of logic families. However, it is recommended to use the ADS5120 with a +1.8V driver supply. This will lower the power dissipation in the output stages due to the lower output swing and reduce current glitches on the supply lines, which otherwise may affect the AC performance of the converter. In some applications it might be advantageous to decouple the DRVDD supply with additional capacitors or a pi-filter. GROUNDING AND DECOUPLING Proper grounding and bypassing, short lead length, and the use of ground planes are particularly important for highfrequency designs. Multilayer PCBs are recommended for best performance since they offer distinct advantages like minimizing ground impedance, separation of signal layers by ground layers, etc. The ADS5120 should be treated as an analog component. Whenever possible, the supply pins should be powered by the analog supply. This will ensure the most consistent results, since digital supply lines often carry high levels of noise which otherwise would be coupled into the converter and degrade the achievable performance. The ground pins should directly connect to an analog ground plane covering the PCB area under the converter. While designing the layout it is important to keep the analog signal traces separated from any digital line to prevent noise coupling onto the analog signal path. Due to its high sampling rate, the ADS5120 generates high-frequency current transients and noise (clock feedthrough) that are fed back into the supply and reference lines. This requires that all supply and reference pins are sufficiently bypassed. In most cases 0.1µF ceramic chip capacitors at each pin are adequate to keep the impedance low over a wide frequency range. Their effectiveness largely depends on the proximity to the individual supply pin. Therefore, they should be located as close to the supply pins as possible. In addition, a larger bipolar capacitor (1µF to 22µF) should be placed on the PCB in proximity of the converter circuit. LAYOUT OF THE PCB WITH A MICROSTAR BGA PACKAGE The ADS5120 is housed in a polyimide film-based chipscale package (CSP). Like most CSPs, solder alloy balls are used as the interconnect between the package substrate and the PCB on which the package is soldered. For detailed information regarding these packages, please refer to literature number SSYZ015B, MicroStar BGA Packaging Reference Guide, which addresses the specific considerations required when integrating a MicroStar BGA package into the PCB design. This document can be found at: http://www-s.ti.com/sc/psheets/ssyz015b/ssyz015b.pdf ADS5120 SBAS247E www.ti.com 15 TERMINOLOGY INTERMODULATION DISTORTION (IMD) ANALOG BANDWIDTH The analog input frequency at which the spectral power of the fundamental frequency (as determined by the FFT analysis) is reduced by 3dB. The 2-tone IMD is the ratio expressed in decibels of either input tone to the worst 3rd-order (or higher) Intermodulation products. The individual input tone levels are at –6.5dB fullscale, and their envelope is at –0.5dB full-scale. OFFSET ERROR (ZERO-SCALE ERROR) APERTURE DELAY The delay between the 50% point of the rising edge of the clock and the instant at which the analog input is sampled. APERTURE UNCERTAINTY (JITTER) The first transition should occur for an analog value 1/2 LSB above negative full-scale. Offset error is defined as the deviation of the actual transition from that point. OFFSET MATCHING The sample-to-sample variation in aperture delay. The change in offset error between adjacent channels. EFFECTIVE NUMBER OF BITS (ENOB) POWER-SUPPLY REJECTION RATIO (PSRR) The ENOB is calculated from the measured SINAD based on the equation: SINAD – 1.76dB ENOB = 6.02 The ratio of a change in input offset voltage to a change in power-supply voltage. SIGNAL-TO-NOISE AND DISTORTION (SINAD) GAIN ERROR Gain Error is the deviation of the actual difference between first and last code transitions and the ideal difference between first and last code transitions. The ratio of the rms signal amplitude (set 0.5dB below fullscale) to the rms value of the sum all other spectral components, including harmonics but excluding DC. SIGNAL-TO-NOISE RATIO (WITHOUT HARMONICS) The ratio of the rms signal amplitude (set 0.5dB below fullscale) to the rms value of the sum of all other spectral components, excluding the first five harmonics and DC. GAIN MATCHING Variation in Gain Error between adjacent channels. HARMONIC DISTORTION, SECOND SPURIOUS-FREE DYNAMIC RANGE (SFDR) The ratio of the rms signal amplitude to the rms value of the 2nd-harmonic component, reported in dBc. HARMONIC DISTORTION, THIRD The ratio of the rms signal amplitude to the rms value of the 3rd-harmonic component, reported in dBc. 16 The ratio of the rms signal amplitude to the rms value of the peak spurious spectral component. The peak spurious component may or may not be a harmonic. May be reported in dBc (i.e., degrades as signal level is lowered), or dBFS (always related back to converter full-scale). ADS5120 www.ti.com SBAS247E Revision History DATE REVISION PAGE SECTION 11/05 E 2 17 Package/Ordering Table Application Information 7/05 D 6 Using External References 2 Abs Max Table 6/04 11/02 6/02 C Include the new package designator ZHK for green/Pb-free package. Added Revision History Table Correct Figure 6: Added DRVDD to PDREF Changed incorrect spec. Was: Clock Input CLK to DGND: –0.3V to AVDD + 0.3V, Changed to: Clock Input CLK to DGND: –0.3V to DRVDD +0.3V 3 DC Characteristics 10 Driving Analog Inputs Added definition of full-scale input range and clarified differential input configuration requirements. 14 Power-Up Sequence Added Power-Up Sequence section 15 PCB Layout "Polymide" corrected to "polyimide" 1 Front Page Added Portable Ultrasound and Portable Instrumentation to Applications Removed Available Options table Moved diagram to page 5 and replaced with new figure 5 Pin Descriptions Table AVDD row, added F2; NC row, added ES; DVDD row, deleted U3; IREFR row, changes 6.19Ω to 6.19kΩ 6 Data Output Pins Table D5C row, changed R19 to T19 B A DESCRIPTION 7 Typical Characteristics 11 Figure 3 1 Front Page Added CLK to Digital Inputs list Replaced 2nd- and 3rd-Harmonic vs Input Frequency curve Resistor RL was changed to R2 Removed ESD-DCM statement from the front of the data sheet. Removed ESD Com row. 2 Abs Max Table 3 DC Characteristics 5 Pin Descriptions Table DNC row, changed L6 to W5 and M1 to U6. NC row, changed U6, W5 to L6, M1 8-9 Typical Characteristics Title changes 10 Figure 1 12 Application Information Add/clarify information for Standby Power Added VBIAS Second paragraph text: Changed +2 to +1 NOTE: Page numbers for previous revisions may differ from page numbers in the current version. ADS5120 SBAS247E www.ti.com 17 PACKAGE OPTION ADDENDUM www.ti.com 24-Jun-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) ADS5120CGHK ACTIVE BGA MICROSTAR GHK 257 90 TBD SNPB Level-3-220C-168 HR Request Free Samples ADS5120CZHK ACTIVE BGA MICROSTAR ZHK 257 90 Green (RoHS & no Sb/Br) SNAGCU Level-3-260C-168 HR Request Free Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP® Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee® Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2010, Texas Instruments Incorporated