POWER DPS50 60 Watts Data Sheet Total Power: 30 - 60 Watts Input Voltage: 90 - 264 Vac 127 - 300 Vdc # of Outputs: Single Special Features CE Mark EMC & LVD (except DPS52) Universal AC input Fully regulated output Overload and short circuit protection Internal remote sense to the output plug Constant voltage Level V efficiency (except DPS52) High MTBF IEC320 AC receptacle, 3 pin (type C14) Built in EMI filter (CISPR 22 Class B) LED power good indicator Input power < 74 watts Complies with EN61000-3-2 Meets Energy Star Safety UL CSA VDE CE CB PSE UL 60950-1 CSA-C22.2 no.60950-1 EN60950-1 EMC, LVD & ErP 2011 (except DPS52) Certificate and report Denan 06-03051012 Electrical Specifications Input Input range 90 - 264 Vac (wide range) Frequency 127 - 300 Vdc Inrush current 47-440 Hz Input current < 60 A @ 230 Vac, cold start @ 25 °C Efficiency < 2.0 A rms @ 115 Vac; < 1 A @ 230 Vac EMI/RFI 80% @ full load typical, @115 Vac Safety ground leakage current FCC Part 15, Subpart B Class B & EN55022 (CISPR 22) Class B 0.5 mA @ 50/60 Hz, 264 Vac input Output Maximum Power (Po) 60 W (DPS52, 30 W) Hold-up time 10ms. typical at full load @ 115 Vac Overvoltage protection 20% - 45% above nominal output maximum Latching type, recycle AC to reset. Overcurrent protection Output short circuit protection auto recover Overload protected @ 120 - 150% above maximum rating Cable/connector DC cable with 2.5 mm center plug DC plug center +v DC plug outer -v Environmental Specifications Operating temperature: 0° to +40 °C ambient. -20 °C start up Storage temperature: -40 °C to +85 °C Electromagnetic susceptibility: Designed to meet EN61000-4, -2, -3, -4, -5, -6, -8, -11, level 3 Humidity: Operating; non-condensing 5% to 90% RH Vibration: Three orthogonal axes, 3 sweeps per axe at 1 oct/min. 2G peak 8 Hz to 500 Hz, operational MTBF demonstrated: > 550,000 hours at full load and 25 °C ambient conditions DPS50 Data Sheet Ordering Information Model Number Maximum Power Output Voltage Maximum Load DPS52* DPS53 30 W 5V 60 W 12 V DPS54 60 W 15 V Ripple P/P (PARD)3 Peak Load1 Regulation2 6A 6.5 A ± 2% 50 mV 5A 5.4 A ± 2% 120 mV 4A 4.3 A ± 2% 150 mV DPS55 60 W 24 V 2.5 A 2.7 A ± 2% 240 mV DPS58 60 W 48 V 1.25 A 1.35 A ± 2% 480 mV 1. Peak current lasting < 15 seconds with a maximum 10% duty cycle. 2. At 25 ºC including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 μF (tantalum capacitor) in parallel with a 0.1 μF capacitor at rated line voltage and load ranges. * No CE approval under new EUP directive 2.39" (60.7) Mechanical Drawing 5.24" (133.0) INDICATOR LED 1.62" (41.0) DC OUTPUT CABLE AC INLET 78.7" (2000±15) MODEL LABEL Notes: 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is ± 0.02” (± 0.5 mm) 3. Warranty: 2 year 4. Weight: 1.06 lb./.48 kg 5. AC input power cord sold separately. 6. Specifications are for convection rating at factory settings at 115 Vac input, 25 °C unless otherwise stated WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2014 Artesyn Embedded Technologies, Inc. www.artesyn.com For more information: www.artesyn.com/power For support: [email protected] DPS50-DS 06.04.14