TI1 LMV358IDDUR Low-voltage rail-to-rail output operational amplifier Datasheet

Product
Folder
Sample &
Buy
Tools &
Software
Technical
Documents
Support &
Community
LMV358, LMV321, LMV324, LMV324S
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
LMV3xx Low-Voltage Rail-to-Rail Output Operational Amplifiers
1 Features
3 Description
•
•
•
•
•
The LMV321, LMV358, LMV324, and LMV324S
devices are single, dual, and quad low-voltage
(2.7 V to 5.5 V) operational amplifiers with rail-to-rail
output swing. These devices are the most costeffective solutions for applications where low-voltage
operation, space saving, and low cost are needed.
These amplifiers are designed specifically for lowvoltage (2.7 V to 5 V) operation, with performance
specifications meeting or exceeding the LM358 and
LM324 devices that operate from 5 V to 30 V. With
package sizes down to one-half the size of the
DBV (SOT-23) package, these devices can be used
for a variety of applications.
1
•
•
2.7-V and 5-V Performance
–40°C to 125°C Operation
Low-Power Shutdown Mode (LMV324S)
No Crossover Distortion
Low Supply Current
– LMV321: 130 μA Typ
– LMV358: 210 μA Typ
– LMV324: 410 μA Typ
– LMV324S: 410 μA Typ
Rail-to-Rail Output Swing
ESD Protection Exceeds JESD 22
– 2000-V Human-Body Model
– 1000-V Charged-Device Model
Device Information(1)
PART NUMBER
LMV324
2 Applications
•
•
•
•
•
•
•
•
•
LMV321
Desktop PCs
HVAC: Heating, Ventilating, and Air Conditioning
Motor Control: AC Induction
Netbooks
Portable Media Players
Power: Telecom DC/DC Module: Digital
Pro Audio Mixers
Refrigerators
Washing Machines: High-End and Low-End
LMV358
PACKAGE (PIN)
BODY SIZE
SOIC (14)
8.65 mm × 3.91 mm
SOT-23 (5)
2.90 mm × 1.60 mm
SC-70 (5)
2.00 mm × 1.25 mm
VSSOP (8)
2.30 mm × 2.00 mm
VSSOP (8)
3.00 mm × 3.00 mm
TSSOP (8)
3.00 mm × 4.40 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
4 Simplified Schematic
–
IN–
OUT
+
IN+
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LMV358, LMV321, LMV324, LMV324S
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Simplified Schematic.............................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
8
1
1
1
1
2
3
4
Absolute Maximum Ratings ..................................... 4
Handling Ratings....................................................... 4
Recommended Operating Conditions ...................... 4
Thermal Information .................................................. 4
Electrical Characteristics: VCC+ = 2.7 V.................... 5
Electrical Characteristics: VCC+ = 5 V....................... 6
Shutdown Characteristics, LMV324S: VCC+ = 2.7 V 7
Shutdown Characteristics, LMV324S: VCC+ = 5 V ... 7
Typical Characteristics .............................................. 8
Detailed Description ............................................ 16
8.1
8.2
8.3
8.4
9
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
16
16
17
17
Application and Implementation ........................ 18
9.1 Typical Application ................................................. 18
10 Power Supply Recommendations ..................... 21
11 Layout................................................................... 22
11.1 Layout Guidelines ................................................. 22
11.2 Layout Example .................................................... 22
12 Device and Documentation Support ................. 23
12.1
12.2
12.3
12.4
Related Links ........................................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
23
23
23
23
13 Mechanical, Packaging, and Orderable
Information ........................................................... 23
5 Revision History
Changes from Revision V (December 2013) to Revision W
•
Page
Added Applications, Handling Rating table, Thermal Information Table, Device Functional Modes, Application and
Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation
Support section, and Mechanical, Packaging, and Orderable Information section................................................................ 1
Changes from Revision U (July 2012) to Revision V
Page
•
Updated document to new TI data sheet format. ................................................................................................................... 1
•
Removed Ordering Information table. .................................................................................................................................... 3
•
Added ESD warning. ............................................................................................................................................................ 23
2
Submit Documentation Feedback
Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
LMV358, LMV321, LMV324, LMV324S
www.ti.com
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
6 Pin Configuration and Functions
LMV358 . . . D (SOIC), DDU (VSSOP),
DGK (VSSOP), OR PW (TSSOP) PACKAGE
(TOP VIEW)
1OUT
1IN–
1IN+
GND
1
8
2
7
3
6
4
5
VCC+
2OUT
2IN–
2IN+
LMV324 . . . D (SOIC) OR PW (TSSOP) PACKAGE
(TOP VIEW)
1OUT
1IN–
1IN+
VCC+
2IN+
2IN–
2OUT
1
14
2
13
3
12
4
11
5
10
6
9
7
8
LMV321 . . . DBV (SOT-23)
OR DCK (SC-70) PACKAGE
(TOP VIEW)
4OUT
4IN–
4IN+
GND
3IN+
3IN–
3OUT
1IN+
1
GND
2
1IN–
3
5
VCC+
4
OUT
LMV324S . . . D (SOIC) OR PW (TSSOP) PACKAGE
(TOP VIEW)
1OUT
1IN–
1IN+
VCC
2IN+
2IN–
2OUT
1/2 SHDN
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
4OUT
4IN–
4IN+
GND
3IN+
3IN–
3OUT
3/4 SHDN
Pin Functions
PIN
LMV358
LMV321
LMV324
LMV324S
D, DDU,
DGK, PW
DBV or DCK
D or PW
D or PW
3/4 SHDN
—
—
—
9
I
Shutdown (logic low)/enable (logic high)
1/2 SHDN
—
—
—
8
I
Shutdown (logic low)/enable (logic high)
1IN+
3
1
3
3
I
Noninverting input
1IN–
2
3
2
2
I
Inverting input
2IN+
5
—
5
5
I
Noninverting input
2IN–
6
—
6
6
I
Inverting input
2OUT
7
—
7
7
O
Output
3IN+
—
—
10
12
I
Noninverting input
3IN–
—
—
9
11
I
Inverting input
3OUT
—
—
8
10
O
Output
4IN+
—
—
12
14
I
Noninverting input
4IN–
—
—
13
15
I
Inverting input
4OUT
—
—
14
16
O
Output
GND
4
2
11
13
-
Negative supply
OUT
1
4
1
1
O
OUT
VCC+
8
5
4
4
-
Positive supply
NAME
Copyright © 1999–2014, Texas Instruments Incorporated
TYPE
DESCRIPTION
Submit Documentation Feedback
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
3
LMV358, LMV321, LMV324, LMV324S
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)
(1)
MIN
(3)
VID
Differential input voltage
VI
Input voltage range (either input)
–0.2
Duration of output short circuit (one amplifier) to ground (4)
TJ
(1)
(2)
(3)
(4)
MAX
Supply voltage (2)
VCC
At or below TA = 25°C,
VCC ≤ 5.5 V
UNIT
5.5
V
±5.5
V
5.7
V
Unlimited
Operating virtual junction temperature
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values (except differential voltages and VCC specified for the measurement of IOS) are with respect to the network GND.
Differential voltages are at IN+ with respect to IN–.
Short circuits from outputs to VCC can cause excessive heating and eventual destruction.
7.2 Handling Ratings
Tstg
Storage temperature range
V(ESD)
(1)
(2)
Electrostatic discharge
MIN
MAX
UNIT
°C
–65
150
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all
pins (1)
0
2500
Charged device model (CDM), per JEDEC specification
JESD22-C101, all pins (2)
0
1500
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions (1)
VCC
Supply voltage (single-supply operation)
VIH
Amplifier turn-on voltage level (LMV324S) (2)
VIL
Amplifier turn-off voltage level (LMV324S)
TA
(1)
(2)
Operating free-air temperature
MIN
MAX
2.7
5.5
VCC = 2.7 V
1.7
VCC = 5 V
3.5
UNIT
V
V
VCC = 2.7 V
0.7
VCC = 5 V
1.5
I temperature (LMV321,
LMV358, LMV324,
LMV321IDCK)
–40
125
I temperature (LMV324S)
-40
85
Q temperature
–40
125
V
°C
All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. See the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
VIH should not be allowed to exceed VCC.
7.4 Thermal Information
LMV3xx
THERMAL METRIC (1)
RθJA
(1)
4
D
Junction-to-ambient thermal resistance
DBV
DCK
DDU
DGK
8 PIN
14 PIN
16 PIN
5 PIN
5 PIN
8 PIN
8 PIN
8 PIN
14 PIN
PW
16 PIN
UNIT
97
86
73
206
252
210
172
149
113
108
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
LMV358, LMV321, LMV324, LMV324S
www.ti.com
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
7.5 Electrical Characteristics: VCC+ = 2.7 V
VCC+ = 2.7 V, TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP (1)
MAX
1.7
7
UNIT
VIO
Input offset voltage
αVIO
Average temperature coefficient of
input offset voltage
IIB
Input bias current
IIO
Input offset current
CMRR
Common-mode rejection ratio
VCM = 0 to 1.7 V
50
63
dB
kSVR
Supply-voltage rejection ratio
VCC = 2.7 V to 5 V, VO = 1 V
50
60
dB
VICR
Common-mode input voltage
range
CMRR ≥ 50 dB
0
–0.2
VO
Output swing
RL = 10 kΩ to 1.35 V
Supply current
11
250
nA
5
50
nA
1.9
VCC – 100
Low level
LMV321I
ICC
μV/°C
5
High level
V
1.7
VCC – 10
60
180
80
170
LMV358I (both amplifiers)
140
340
LMV324I and LMV324SI
(all four amplifiers)
260
680
mV
μA
B1
Unity-gain bandwidth
Φm
Phase margin
Gm
Gain margin
10
dB
Vn
Equivalent input noise voltage
f = 1 kHz
46
nV/√Hz
In
Equivalent input noise current
f = 1 kHz
0.17
pA/√Hz
(1)
CL = 200 pF
mV
1
MHz
60
deg
Typical values represent the likely parametric nominal values determined at the time of characterization. Typical values depend on the
application and configuration and may vary over time. Typical values are not ensured on production material.
Copyright © 1999–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
5
LMV358, LMV321, LMV324, LMV324S
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
www.ti.com
7.6 Electrical Characteristics: VCC+ = 5 V
VCC+ = 5 V, at specified free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
(1)
MIN
25°C
TYP (2)
MAX
1.7
7
UNIT
VIO
Input offset voltage
αVIO
Average temperature
coefficient of input offset
voltage
IIB
Input bias current
IIO
Input offset current
CMRR
Common-mode rejection
ratio
VCM = 0 to 4 V
25°C
50
65
dB
kSVR
Supply-voltage
rejection ratio
VCC = 2.7 V to 5 V, VO = 1 V,
VCM = 1 V
25°C
50
60
dB
VICR
Common-mode input
voltage range
CMRR ≥ 50 dB
25°C
0
–0.2
Full range
Output swing
High level
RL = 10 kΩ to 2.5 V
Low level
IOS
Output short-circuit
current
RL = 2 kΩ
Sourcing, VO = 0 V
Sinking, VO = 5 V
LMV321I
ICC
Supply current
LMV358I (both amplifiers)
LMV324I and LMV324SI
(all four amplifiers)
B1
Unity-gain bandwidth
Φm
Gm
Vn
Equivalent input
noise voltage
In
Equivalent input
noise current
SR
Slew rate
(1)
(2)
6
25°C
15
5
CL = 200 pF
250
50
150
4.2
25°C
VCC – 300
Full range
VCC – 400
25°C
4
Full range
Full range
VCC – 200
25°C
nA
V
300
400
VCC – 100
nA
VCC – 40
120
25°C
mV
μV/°C
500
25°C
Low level
Large-signal differential
voltage gain
5
Full range
RL = 2 kΩ to 2.5 V
AVD
25°C
Full range
High level
VO
9
VCC – 10
65
Full range
mV
180
280
25°C
15
Full range
10
25°C
25°C
100
5
60
10
160
130
Full range
V/mV
mA
250
350
25°C
210
Full range
440
615
25°C
410
Full range
μA
830
1160
25°C
1
MHz
Phase margin
25°C
60
deg
Gain margin
25°C
10
dB
f = 1 kHz
25°C
39
nV/√Hz
f = 1 kHz
25°C
0.21
pA/√Hz
25°C
1
V/μs
Full range TA = –40°C to 125°C for I temperature(LMV321, LMV358, LMV324, LMV321IDCK), –40°C to 85°C for (LMV324S) and –40°C
to 125°C for Q temperature.
Typical values represent the likely parametric nominal values determined at the time of characterization. Typical values depend on the
application and configuration and may vary over time. Typical values are not ensured on production material.
Submit Documentation Feedback
Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
LMV358, LMV321, LMV324, LMV324S
www.ti.com
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
7.7 Shutdown Characteristics, LMV324S: VCC+ = 2.7 V
VCC+ = 2.7 V, TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP (1)
MAX
UNIT
ICC(SHDN)
Supply current in shutdown mode
(per channel)
SHDN ≤ 0.6 V
t(on)
Amplifier turn-on time
AV = 1, RL = Open (measured at 50% point)
2
μs
t(off)
Amplifier turn-off time
AV = 1, RL = Open (measured at 50% point)
40
ns
(1)
5
μA
Typical values represent the likely parametric nominal values determined at the time of characterization. Typical values depend on the
application and configuration and may vary over time. Typical values are not ensured on production material.
7.8 Shutdown Characteristics, LMV324S: VCC+ = 5 V
VCC+ = 5 V, TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP (1)
MAX
UNIT
ICC(SHDN)
Supply current in shutdown mode
(per channel)
SHDN ≤ 0.6 V, TA = Full Temperature Range
t(on)
Amplifier turn-on time
AV = 1, RL = Open (measured at 50% point)
2
μs
t(off)
Amplifier turn-off time
AV = 1, RL = Open (measured at 50% point)
40
ns
(1)
5
μA
Typical values represent the likely parametric nominal values determined at the time of characterization. Typical values depend on the
application and configuration and may vary over time. Typical values are not ensured on production material.
Copyright © 1999–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
7
LMV358, LMV321, LMV324, LMV324S
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
www.ti.com
7.9 Typical Characteristics
Vs = 2.7 V
RL = 100 kΩ, 2 kΩ, 600 Ω
70
Phase
60
Gain − dB
40
100 kΩ
Gain
70
90
60
75
60
2 kΩ
30
105
45
20
30
600 Ω
10
100 kΩ
−10
1k
10 k
600 Ω
Phase
75
2 kΩ
40
100 k
Frequency − Hz
30
45
Gain
20
10
15
1M
0
0
−15
10 M
−10
1k
70
10 k
70
100
Phase
0 pF
80
−20
−20
Vs = 5.0 V
RL = 600 Ω
CL = 0 pF
100 pF
500 pF
1000 pF
−30
10 k
−40
100 pF
500 pF
0 pF
−60
1000 pF
−80
−100
10 M
100 k
1M
Frequency − Hz
Gain − dB
Gain − dB
Gain
40
40
30
0
10
−20
Vs = 5.0 V
0 pF
RL = 100 kΩ
100 pF
−10 CL = 0 pF
100 pF
500 pF
−20
500 pF
1000 pF
1000 pF
−30
10 k
100 k
1M
Frequency − Hz
60
Gain − dB
25°C
60
40
−40°C
30
45
Gain
20
85°C
25°C
0
−10
1k
30
−40°C
10 k
100 k
1M
Frequency − Hz
Figure 5. LMV321 Frequency Response
vs Temperature
8
Submit Documentation Feedback
RL
CL
−2.5 V
1000
LMV3xx
(25% Overshoot)
100
VCC = ±2.5 V
AV = +1
RL = 2 kΩ
VO = 100 mVPP
0
−15
10 M
VO
+
VI
15
10
_
90
75
−100
10 M
2.5 V
LMV324S
(25% Overshoot)
Phase Margin − Deg
Phase
50
−80
10000
105
85°C
−60
Figure 4. LMV321 Frequency Response
vs Capacitive Load
Capacitive Load − pF
70
−40
0
120
Vs = 5.0 V
RL = 2 kΩ
20
20
Figure 3. LMV321 Frequency Response
vs Capacitive Load
80
500 pF
Gain
Phase Margin − Deg
0
20
−10
20
Phase Margin − Deg
500 pF
60
100 pF
1000 pF
40
1000 pF
0 pF
50
100 pF
40
80
60
60
50
0
−15
10 M
100 k
1M
Frequency − Hz
Figure 2. LMV321 Frequency Response
vs Resistive Load
100
60
0
600 Ω
Phase
10
30
100 kΩ
Figure 1. LMV321 Frequency Response
vs Resistive Load
30
60
100 kΩ
2 kΩ
2 kΩ
0
105
90
50
15
120
Vs = 5.0 V
RL = 100 kΩ, 2 kΩ, 600 Ω
Phase Margin − Deg
600 Ω
80
Phase Margin − Deg
50
120
Gain − dB
80
10
−2
−1.5
−1
−0.5
0
0.5
1
1.5
Output Voltage − V
Figure 6. Stability
vs Capacitive Load
Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
LMV358, LMV321, LMV324, LMV324S
www.ti.com
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
Typical Characteristics (continued)
10000
10000
VCC = ±2.5 V
RL = 2 kΩ
AV = 10
VO = 100 mVPP
2.5 V
_
1000
VO
+
RL
CL
Capacitive Load − nF
Capacitive Load − pF
VI
2.5 V
LMV324S
(25% Overshoot)
100
10
−2.0
−1.5
1000
LMV3xx
(25% Overshoot)
100
134 kΩ
−1
−0.5
0
Output Voltage − V
0.5
1
1.21 MΩ
+2.5 V
VCC = ±2.5 V
AV = +1
RL = 1 MΩ
VO = 100 mVPP
LMV3xx
(25% Overshoot)
_
10
−2.0
1.5
−1.5
−1
−0.5
0
Output Voltage − V
1
1.5
Figure 8. Stability
vs Capacitive Load
RL = 100 kΩ
1.400
LMV3xx
(25% Overshoot)
1.300
Slew Rate − V/ms
Capacitive Load − nF
0.5
1.500
VCC = ±2.5 V
RL = 1 MΩ
AV = 10
VO = 100 mVPP
1000
LMV324S
(25% Overshoot)
134 kΩ
1.21 MΩ
VI
CL
RL
−1
1.000
LMV3xx
PSLEW
0.900
−0.5
0
NSLEW
LMV324S
0.600
−2.5 V
−1.5
NSLEW
1.100
0.700
VO
+
Gain
1.200
0.800
+2.5 V
_
0.5
1
0.500
2.5
1.5
PSLEW
3.0
3.5
4.0
4.5
5.0
V CC − Supply Voltage − V
Output Voltage − V
Figure 10. Slew Rate
vs Supply Voltage
Figure 9. Stability
vs Capacitive Load
−10
700
VCC = 5 V
VI = VCC/2
LMV3xx
600
LMV324S
−20
TA = 85°C
500
Input Current − nA
Supply Current − µA
CL
RL
−2.5 V
10000
10
−2.0
VO
+
VI
Figure 7. Stability
vs Capacitive Load
100
LMV324S
(25% Overshoot)
TA = 25°C
400
300
TA = −40°C
−30
LMV3xx
−40
200
−50
LMV324S
100
0
0
1
2
3
4
5
6
−60
−40 −30 −20 −10 0 10 20 30 40 50 60 70 80
TA − °C
VCC − Supply Voltage − V
Figure 11. Supply Current
vs Supply Voltage - Quad Amplifier
Copyright © 1999–2014, Texas Instruments Incorporated
Figure 12. Input Current
vs Temperature
Submit Documentation Feedback
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
9
LMV358, LMV321, LMV324, LMV324S
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
www.ti.com
Typical Characteristics (continued)
100
100
VCC = 2.7 V
VCC = 5 V
10
Sourcing Current − mA
Sourcing Current − mA
10
LMV3xx
1
LMV324S
0.1
LMV3xx
1
LMV324S
0.1
0.01
0.01
0.001
0.001
0.01
0.1
1
0.001
0.001
10
Figure 13. Source Current
vs Output Voltage
10
LMV324S
Sinking Current − mA
LMV324S
1
LMV3xx
0.1
1
LMV324
0.1
0.01
0.01
0.01
0.1
1
10
0.001
0.001
Output Voltage Referenced to GND − V
0.01
0.1
120
LMV324S
VCC = 5 V
270
LMV3xx
VCC = 5 V
180
150
120
90
LMV324S
VCC = 2.7 V
LMV3xx
VCC = 2.7 V
Sourcing Current − mA
Sinking Current − mA
100
LMV324S
VCC = 5 V
80
LMV3xx
VCC = 5 V
60
LMV3xx
VCC = 2.7 V
40
LMV324S
VCC = 2.7 V
20
30
0
−40 −30 −20 −10 0
0
10 20 30 40 50 60 70 80 90
TA − °C
Figure 17. Short-Circuit Current
vs Temperature
10
10
Figure 16. Sinking Current
vs Output Voltage
300
60
1
Output Voltage Referenced to GND − V
Figure 15. Sinking Current
vs Output Voltage
210
10
VCC = 5 V
10
240
1
100
VCC = 2.7 V
Sinking Current − mA
0.1
Figure 14. Source Current
vs Output Voltage
100
0.001
0.001
0.01
Output Voltage Referenced to VCC+ − V
Output Voltage Referenced to VCC+ − V
Submit Documentation Feedback
−40 −30 −20−10 0
10 20 30 40 50 60 70 80 90
TA − °C
Figure 18. Short-Circuit Current
vs Temperature
Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
LMV358, LMV321, LMV324, LMV324S
www.ti.com
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
Typical Characteristics (continued)
80
90
LMV324S
VCC = −5 V
RL = 10 kΩ
70
VCC = 5 V
RL = 10 kΩ
70
60
LMV3xx
LMV3xx
60
50
+k SVR − dB
−k SVR − dB
LMV324S
80
40
30
50
40
30
20
20
10
10
0
0
100
1k
10k
100k
1M
1k
Figure 20. +kSVR
vs Frequency
80
VCC = −2.7 V
RL = 10 kΩ
LMV324S
70
60
1M
VCC = 2.7 V
RL = 10 kΩ
60
LMV3xx
+k SVR − dB
50
40
30
50
30
20
10
10
100
1k
10k
100k
0
100
1M
LMV3xx
40
20
0
1k
10k
Frequency − Hz
Figure 21. –kSVR
vs Frequency
Figure 22. +kSVR
vs Frequency
6
60
Peak Output Voltage − V OPP
5
LMV3xx
LMV324S
Negative Swing
40
30
20
Positive Swing
1M
RL = 10 kΩ
THD > 5%
AV = 3
RL = 10 kΩ
50
100k
Frequency − Hz
70
Output Voltage Swing − mV
100k
Figure 19. –kSVR
vs Frequency
LMV324S
70
10k
Frequency − Hz
80
−kSVR − dB
100
Frequency − Hz
LMV3xx
VCC = 5 V
4
LMV324S
VCC = 5 V
3
LMV3xx
VCC = 2.7 V
2
LMV324S
VCC = 2.7 V
1
10
0
2.5
3.0
3.5
4.0
4.5
5.0
VCC − Supply Voltage − V
Figure 23. Output Voltage Swing From Rails
vs Supply Voltage
Copyright © 1999–2014, Texas Instruments Incorporated
0
1k
10k
100k
1M
10M
Frequency − Hz
Figure 24. Output Voltage
vs Frequency
Submit Documentation Feedback
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
11
LMV358, LMV321, LMV324, LMV324S
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
www.ti.com
Typical Characteristics (continued)
150
110
LMV3xx
VCC = 5 V
Impedance − Ω
90
80
70
LMV324S
VCC = 2.7 V
60
50
LMV324S
VCC = 5 V
40
VCC = 5 V
RL = 5 kΩ
AV = 1
VO = 3 VPP
140
Crosstalk Rejection − dB
100
LMV3xx
VCC = 2.7 V
130
120
110
100
30
20
1
1M
2M
3M
90
100
4M
Frequency − Hz
1k
10k
Frequency − Hz
Figure 25. Open-Loop Output Impedence
vs Frequency
Figure 26. Cross-Talk Rejection
vs Frequency
Input
LMV3xx
LMV3xx
1 V/Div
1 V/Div
Input
LMV324S
VCC = ±2.5 V
RL = 2 kΩ
TA = 25°C
LMV324S
VCC = ±2.5 V
RL = 2 kΩ
TA = 85°C
1 µs/Div
Figure 28. Noninverting Large-Signal Pulse Response
1 µs/Div
Figure 27. Noninverting Large-Signal Pulse Response
Input
Input
LMV3xx
LMV3xx
50 mV/Div
1 V/Div
100k
LMV324S
LMV324S
VCC = ±2.5 V
RL = 2 kΩ
TA = 25°C
VCC = ±2.5 V
RL = 2 kΩ
TA = −40°C
1 µs/Div
Figure 29. Noninverting Large-Signal Pulse Response
12
Submit Documentation Feedback
1 µs/Div
Figure 30. Noninverting Small-Signal Pulse Response
Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
LMV358, LMV321, LMV324, LMV324S
www.ti.com
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
Typical Characteristics (continued)
Input
Input
50 mV/Div
50 mV/Div
LMV3xx
LMV3xx
LMV324S
LMV324S
VCC = ±2.5 V
RL = 2 kΩ
TA = 85°C
VCC = ±2.5 V
RL = 2 kΩ
TA = −40°C
1 µs/Div
Figure 32. Noninverting Small-Signal Pulse Response
1 µs/Div
Figure 31. Noninverting Small-Signal Pulse Response
Input
Input
LMV3xx
1 V/Div
1 V/Div
LMV3xx
LMV324S
LMV324S
VCC = ±2.5 V
RL = 2 kΩ
TA = 25°C
VCC = ±2.5 V
RL = 2 kΩ
TA = 85°C
1 µs/Div
Figure 33. Inverting Large-Signal Pulse Response
1 µs/Div
Figure 34. Inverting Large-Signal Pulse Response
Input
Input
LMV3xx
1 V/Div
50 mV/Div
LMV3xx
LMV324S
LMV324S
VCC = ±2.5 V
RL = 2 kΩ
TA = 25°C
VCC = ±2.5 V
RL = 2 kΩ
TA = −40°C
1 µs/Div
Figure 35. Inverting Large-Signal Pulse Response
Copyright © 1999–2014, Texas Instruments Incorporated
1 µs/Div
Figure 36. Inverting Small-Signal Pulse Response
Submit Documentation Feedback
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
13
LMV358, LMV321, LMV324, LMV324S
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
www.ti.com
Input
Input
LMV3xx
LMV3xx
50 mV/Div
50 mV/Div
Typical Characteristics (continued)
LMV324S
LMV324S
VCC = ±2.5 V
RL = 2 kΩ
TA = −40°C
VCC = ±2.5 V
RL = 2 kΩ
TA = 85°C
1 µs/Div
1 µs/Div
Figure 37. Inverting Small-Signal Pulse Response
Figure 38. Inverting Small-Signal Pulse Response
0.50
0.80
0.60
0.40
0.20
VCC = 5 V
0.45
Input Current Noise − pA/ Hz
Input Current Noise − pA/ Hz
VCC = 2.7 V
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0.00
0.00
10
100
1k
10
10k
100
10k
Figure 40. Input Current Noise
vs Frequency
Figure 39. Input Current Noise
vs Frequency
200
10.000
180
160
1.000
VCC = 2.7 V
RL = 10 kΩ
AV = 1
VO = 1 VPP
140
120
THD − %
Input Voltage Noise − nV/ Hz
1k
Frequency − Hz
Frequency − Hz
100
LMV3xx
0.100
80
VCC = 2.7 V
60
0.010
LMV324S
40
VCC = 5 V
0.001
20
10
100
1k
10k
10
100
Figure 41. Input Voltage Noise
vs Frequency
14
Submit Documentation Feedback
1000
10000
100000
Frequency − Hz
Frequency − Hz
Figure 42. THD + N
vs Frequency
Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
LMV358, LMV321, LMV324, LMV324S
www.ti.com
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
Typical Characteristics (continued)
10.000
10.000
VCC = 2.7 V
RL = 10 kΩ
AV = 10
VO = 1 VPP
1.000
1.000
VCC = 5 V
RL = 10 kΩ
AV = 1
VO = 1 VPP
THD − %
THD − %
LMV324S
0.100
LMV3xx
0.100
LMV324S
0.010
0.010
LMV3xx
0.001
0.001
10
100
1000
10000
10
100000
1000
100
Frequency − Hz
10000
100000
Frequency − Hz
Figure 43. THD + N
vs Frequency
Figure 44. THD + N
vs Frequency
10.000
VCC = 5 V
RL = 10 kΩ
AV = 10
VO = 2.5 VPP
1.000
THD − %
LMV324S
0.100
0.010
LMV3xx
0.001
10
100
1000
10000
100000
Frequency − Hz
Figure 45. THD + N
vs Frequency
Copyright © 1999–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
15
LMV358, LMV321, LMV324, LMV324S
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
www.ti.com
8 Detailed Description
8.1 Overview
The LMV321, LMV358, LMV324, and LMV324S devices are single, dual, and quad low-voltage (2.7 V to 5.5 V)
operational amplifiers with rail-to-rail output swing. The LMV324S device, which is a variation of the standard
LMV324 device, includes a power-saving shutdown feature that reduces supply current when the amplifiers are
not needed. Channels 1 and 2 together are put in shutdown, as are channels 3 and 4. While in shutdown, the
outputs actively are pulled low.
The LMV321, LMV358, LMV324, and LMV324S devices are the most cost-effective solutions for applications
where low-voltage operation, space saving, and low cost are needed. These amplifiers are designed specifically
for low-voltage (2.7 V to 5 V) operation, with performance specifications meeting or exceeding the LM358 and
LM324 devices that operate from 5 V to 30 V. Additional features of the LMV3xx devices are a common-mode
input voltage range that includes ground, 1-MHz unity-gain bandwidth, and 1-V/μs slew rate.
The LMV321 device is available in the ultra-small package, which is approximately one-half the size of the DBV
(SOT-23) package. This package saves space on printed circuit boards and enables the design of small portable
electronic devices. It also allows the designer to place the device closer to the signal source to reduce noise
pickup and increase signal integrity.
8.2 Functional Block Diagram
VCC
VBIAS1
VCC
+
–
VBIAS2
+
Output
–
VCC VCC
VBIAS3
+
IN-
VBIAS4–
IN+
+
–
16
Submit Documentation Feedback
Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
LMV358, LMV321, LMV324, LMV324S
www.ti.com
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
8.3 Feature Description
8.3.1 Operating Voltage
The LMV321, LMV358, LMV324, LMV324S devices are fully specified and ensured for operation from
2.7 V to 5 V. In addition, many specifications apply from –40°C to 125°C. Parameters that vary significantly with
operating voltages or temperature are shown in the Typical Characteristics graphs.
8.3.2 Unity-Gain Bandwidth
The unity-gain bandwidth is the frequency up to which an amplifier with a unity gain may be operated without
greatly distorting the signal. The LMV321, LMV358, LMV324, LMV324S devices have a 1-MHz unity-gain
bandwidth.
8.3.3 Slew Rate
The slew rate is the rate at which an operational amplifier can change its output when there is a change on the
input. The LMV321, LMV358, LMV324, LMV324S devices have a 1-V/μs slew rate.
8.4 Device Functional Modes
The LMV321, LMV358, LMV324, LMV324S devices are powered on when the supply is connected. The
LMV324S device, which is a variation of the standard LMV324 device, includes a power-saving shutdown feature
that reduces supply current to a maximum of 5 μA per channel when the amplifiers are not needed. Each of
these devices can be operated as a single supply operational amplifier or dual supply amplifier depending on the
application.
Copyright © 1999–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
17
LMV358, LMV321, LMV324, LMV324S
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
www.ti.com
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Typical Application
Some applications require differential signals. Figure 46 shows a simple circuit to convert a single-ended input of
0.5 to 2 V into differential output of ±1.5 V on a single 2.7-V supply. The output range is intentionally limited to
maximize linearity. The circuit is composed of two amplifiers. One amplifier acts as a buffer and creates a
voltage, VOUT+. The second amplifier inverts the input and adds a reference voltage to generate VOUT–. Both
VOUT+ and VOUT– range from 0.5 to 2 V. The difference, VDIFF, is the difference between VOUT+ and VOUT–. The
LMV358 was used to build this circuit.
R2
2.7 V
R1
VOUT+
+
R3
VREF
2.5 V
R4
VDIFF
±
VOUT+
+
VIN
Figure 46. Schematic for Single-Ended Input to Differential Output Conversion
18
Submit Documentation Feedback
Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
LMV358, LMV321, LMV324, LMV324S
www.ti.com
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
Typical Application (continued)
9.1.1 Design Requirements
The design requirements are as follows:
• Supply voltage: 2.7 V
• Reference voltage: 2.5 V
• Input: 0.5 to 2 V
• Output differential: ±1.5 V
9.1.2 Detailed Design Procedure
The circuit in Figure 46 takes a single-ended input signal, VIN, and generates two output signals, VOUT+ and
VOUT– using two amplifiers and a reference voltage, VREF. VOUT+ is the output of the first amplifier and is a
buffered version of the input signal, VIN (see Equation 1). VOUT– is the output of the second amplifier which uses
VREF to add an offset voltage to VIN and feedback to add inverting gain. The transfer function for VOUT– is
Equation 2.
VOUT+ = VIN
(1)
æ R 44 ö æ R22 ö
R2
VOUT
- VINin ´ 2
out - = VREF
ref ´ ç
÷ ´ ç1 +
÷
+ R 44 ø è
R11 ø
R11
è R33+
(2)
The differential output signal, VDIFF, is the difference between the two single-ended output signals, VOUT+ and
VOUT–. Equation 3 shows the transfer function for VDIFF. By applying the conditions that R1 = R2 and R3 = R4, the
transfer function is simplified into Equation 6. Using this configuration, the maximum input signal is equal to the
reference voltage and the maximum output of each amplifier is equal to the VREF. The differential output range is
2×VREF. Furthermore, the common mode voltage will be one half of VREF (see Equation 7).
æ
öæ
æ
R ö
R4
R2 ö
VD IF F = V O U T + - V O U T - = VIN ´ ç 1 + 2 ÷ - VR E F ´ ç
÷ ç1 +
÷
R1 ø
R1 ø
è
è R3 + R4 ø è
VOUT+ = VIN
VOUT– = VREF – VIN
VDIFF = 2×VIN – VREF
(3)
(4)
(5)
(6)
+ VOUT - ö 1
æV
Vcm = ç OUT +
÷ = VREF
2
è
ø 2
(7)
9.1.2.1 Amplifier Selection
Linearity over the input range is key for good dc accuracy. The common mode input range and the output swing
limitations determine the linearity. In general, an amplifier with rail-to-rail input and output swing is required.
Bandwidth is a key concern for this design. Because LMV358 has a bandwidth of 1 MHz, this circuit will only be
able to process signals with frequencies of less than 1 MHz.
9.1.2.2 Passive Component Selection
Because the transfer function of VOUT– is heavily reliant on resistors (R1, R2, R3, and R4), use resistors with low
tolerances to maximize performance and minimize error. This design used resistors with resistance values of
36 kΩ with tolerances measured to be within 2%. If the noise of the system is a key parameter, the user can
select smaller resistance values (6 kΩ or lower) to keep the overall system noise low. This ensures that the noise
from the resistors is lower than the amplifier noise.
Copyright © 1999–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
19
LMV358, LMV321, LMV324, LMV324S
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
www.ti.com
Typical Application (continued)
9.1.3 Application Curves
The measured transfer functions in Figure 47, Figure 48, and Figure 49 were generated by sweeping the input
voltage from 0 V to 2.5 V. However, this design should only be used between 0.5 V and 2 V for optimum
linearity.
2.5
2.5
2.0
1.5
2.0
VOUT+ (V)
VDIFF (V)
1.0
0.5
0.0
±0.5
1.5
1.0
±1.0
0.5
±1.5
±2.0
0.0
±2.5
0.0
0.5
1.0
1.5
2.0
0.0
2.5
VIN (V)
0.5
1.0
1.5
VIN (V)
C003
Figure 47. Differential Output Voltage vs Input Voltage
2.0
2.5
C001
Figure 48. Positive Output Voltage Node vs Input Voltage
3.0
2.5
VOUTt (V)
2.0
1.5
1.0
0.5
0.0
0.0
0.5
1.0
1.5
VIN (V)
2.0
2.5
C002
Figure 49. Positive Output Voltage Node vs Input Voltage
20
Submit Documentation Feedback
Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
LMV358, LMV321, LMV324, LMV324S
www.ti.com
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
10 Power Supply Recommendations
The LMV321, LMV358, LMV324, LMV324S devices are specified for operation from 2.7 to 5 V; many
specifications apply from –40°C to 125°C. The Typical Characteristics section presents parameters that can
exhibit significant variance with regard to operating voltage or temperature.
CAUTION
Supply voltages larger than 5.5 V can permanently damage the device (see the
Absolute Maximum Ratings ).
Place 0.1-μF bypass capacitors close to the power-supply pins to reduce errors coupling in from noisy or high
impedance power supplies. For more detailed information on bypass capacitor placement, refer to the Layout.
Copyright © 1999–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
21
LMV358, LMV321, LMV324, LMV324S
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
www.ti.com
11 Layout
11.1 Layout Guidelines
For best operational performance of the device, use good PCB layout practices, including:
• Noise can propagate into analog circuitry through the power pins of the circuit as a whole, as well as the
operational amplifier. Bypass capacitors are used to reduce the coupled noise by providing low impedance
power sources local to the analog circuitry.
– Connect low-ESR, 0.1-μF ceramic bypass capacitors between each supply pin and ground, placed as
close to the device as possible. A single bypass capacitor from V+ to ground is applicable for single
supply applications.
• Separate grounding for analog and digital portions of circuitry is one of the simplest and most-effective
methods of noise suppression. One or more layers on multilayer PCBs are usually devoted to ground planes.
A ground plane helps distribute heat and reduces EMI noise pickup. Make sure to physically separate digital
and analog grounds, paying attention to the flow of the ground current. For more detailed information, refer to
Circuit Board Layout Techniques, (SLOA089).
• To reduce parasitic coupling, run the input traces as far away from the supply or output traces as possible. If
it is not possible to keep them separate, it is much better to cross the sensitive trace perpendicular as
opposed to in parallel with the noisy trace.
• Place the external components as close to the device as possible. Keeping RF and RG close to the inverting
input minimizes parasitic capacitance, as shown in Layout Example.
• Keep the length of input traces as short as possible. Always remember that the input traces are the most
sensitive part of the circuit.
• Consider a driven, low-impedance guard ring around the critical traces. A guard ring can significantly reduce
leakage currents from nearby traces that are at different potentials.
11.2 Layout Example
VIN
RIN
RG
+
VOUT
RF
Figure 50. Operational Amplifier Schematic for Noninverting Configuration
Place components close to
device and to each other to
reduce parasitic errors
Run the input traces as far
away from the supply lines
as possible
VS+
RF
OUT1
VCC+
GND
IN1í
OUT2
VIN
IN1+
IN2í
VCCí
IN2+
RG
GND
RIN
Use low-ESR, ceramic
bypass capacitor
Only needed for
dual-supply
operation
GND
VS(or GND for single supply)
Ground (GND) plane on another layer
Figure 51. Operational Amplifier Board Layout for Noninverting Configuration
22
Submit Documentation Feedback
Copyright © 1999–2014, Texas Instruments Incorporated
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
LMV358, LMV321, LMV324, LMV324S
www.ti.com
SLOS263W – AUGUST 1999 – REVISED OCTOBER 2014
12 Device and Documentation Support
12.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 1. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
LMV321
Click here
Click here
Click here
Click here
Click here
LMV358
Click here
Click here
Click here
Click here
Click here
LMV324
Click here
Click here
Click here
Click here
Click here
LMV324S
Click here
Click here
Click here
Click here
Click here
12.2 Trademarks
All trademarks are the property of their respective owners.
12.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser based versions of this data sheet, refer to the left hand navigation.
Copyright © 1999–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LMV358 LMV321 LMV324 LMV324S
23
PACKAGE OPTION ADDENDUM
www.ti.com
15-Apr-2017
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LMV321IDBVR
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(RC1F ~ RC1K)
LMV321IDBVRE4
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(RC1F ~ RC1K)
LMV321IDBVRG4
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(RC1F ~ RC1K)
LMV321IDBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(RC1F ~ RC1K)
LMV321IDBVTE4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(RC1F ~ RC1K)
LMV321IDBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(RC1F ~ RC1K)
LMV321IDCKR
ACTIVE
SC70
DCK
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU |
CU NIPDAUAG
Level-1-260C-UNLIM
-40 to 125
(R3C ~ R3F ~ R3O ~
R3R ~ R3Z)
LMV321IDCKRE4
ACTIVE
SC70
DCK
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-1-260C-UNLIM
-40 to 85
(R3C ~ R3F ~ R3O ~
R3R ~ R3Z)
LMV321IDCKRG4
ACTIVE
SC70
DCK
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-1-260C-UNLIM
-40 to 125
(R3C ~ R3F ~ R3O ~
R3R ~ R3Z)
LMV321IDCKT
ACTIVE
SC70
DCK
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU |
CU NIPDAUAG
Level-1-260C-UNLIM
-40 to 125
(R3C ~ R3F ~ R3R)
LMV321IDCKTG4
ACTIVE
SC70
DCK
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-1-260C-UNLIM
-40 to 125
(R3C ~ R3F ~ R3R)
LMV324ID
ACTIVE
SOIC
D
14
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
LMV324I
LMV324IDG4
ACTIVE
SOIC
D
14
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
LMV324I
LMV324IDR
ACTIVE
SOIC
D
14
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-1-260C-UNLIM
-40 to 125
LMV324I
LMV324IDRE4
ACTIVE
SOIC
D
14
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
LMV324I
LMV324IDRG4
ACTIVE
SOIC
D
14
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
LMV324I
LMV324IPWR
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-1-260C-UNLIM
-40 to 125
MV324I
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
15-Apr-2017
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LMV324IPWRE4
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV324I
LMV324IPWRG4
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV324I
LMV324QD
ACTIVE
SOIC
D
14
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
LMV324Q
LMV324QDG4
ACTIVE
SOIC
D
14
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
LMV324Q
LMV324QDR
ACTIVE
SOIC
D
14
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
LMV324Q
LMV324QDRG4
ACTIVE
SOIC
D
14
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
LMV324Q
LMV324QPW
ACTIVE
TSSOP
PW
14
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV324Q
LMV324QPWG4
ACTIVE
TSSOP
PW
14
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV324Q
LMV324QPWR
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV324Q
LMV324QPWRE4
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV324Q
LMV358ID
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV358I
LMV358IDDUR
ACTIVE
VSSOP
DDU
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
RA5R
LMV358IDDURG4
ACTIVE
VSSOP
DDU
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
RA5R
LMV358IDE4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV358I
LMV358IDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV358I
LMV358IDGKR
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(R5B ~ R5Q ~ R5R)
LMV358IDGKRG4
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(R5B ~ R5Q ~ R5R)
LMV358IDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-1-260C-UNLIM
-40 to 125
MV358I
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
15-Apr-2017
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LMV358IDRE4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV358I
LMV358IDRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV358I
LMV358IPW
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV358I
LMV358IPWG4
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV358I
LMV358IPWR
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-1-260C-UNLIM
-40 to 125
MV358I
LMV358IPWRE4
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV358I
LMV358IPWRG4
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV358I
LMV358QD
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV358Q
LMV358QDDUR
ACTIVE
VSSOP
DDU
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
RAHR
LMV358QDDURG4
ACTIVE
VSSOP
DDU
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
RAHR
LMV358QDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV358Q
LMV358QDGKR
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(RHO ~ RHR)
LMV358QDGKRG4
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(RHO ~ RHR)
LMV358QDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV358Q
LMV358QPWR
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
MV358Q
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 3
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
15-Apr-2017
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 4
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Dec-2016
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
LMV321IDBVR
SOT-23
3000
178.0
9.0
DBV
5
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3.23
3.17
1.37
4.0
8.0
Q3
LMV321IDBVT
SOT-23
DBV
5
250
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
LMV321IDCKR
SC70
DCK
5
3000
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
LMV321IDCKR
SC70
DCK
5
3000
180.0
9.2
2.3
2.55
1.2
4.0
8.0
Q3
LMV321IDCKT
SC70
DCK
5
250
180.0
9.2
2.3
2.55
1.2
4.0
8.0
Q3
LMV321IDCKT
SC70
DCK
5
250
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
LMV324IDR
SOIC
D
14
2500
330.0
16.4
6.5
9.0
2.1
8.0
16.0
Q1
LMV324IDR
SOIC
D
14
2500
330.0
16.4
6.5
9.0
2.1
8.0
16.0
Q1
LMV324IDR
SOIC
D
14
2500
330.0
16.8
6.5
9.5
2.3
8.0
16.0
Q1
LMV324IDRG4
SOIC
D
14
2500
330.0
16.4
6.5
9.0
2.1
8.0
16.0
Q1
LMV324IPWR
TSSOP
PW
14
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
LMV324IPWR
TSSOP
PW
14
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
LMV324IPWRG4
TSSOP
PW
14
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
LMV324QDR
SOIC
D
14
2500
330.0
16.4
6.5
9.0
2.1
8.0
16.0
Q1
LMV324QPWR
TSSOP
PW
14
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
LMV358IDDUR
VSSOP
DDU
8
3000
180.0
8.4
2.25
3.35
1.05
4.0
8.0
Q3
LMV358IDGKR
VSSOP
DGK
8
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LMV358IDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Dec-2016
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LMV358IDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
LMV358IDR
SOIC
D
8
2500
330.0
12.8
6.4
5.2
2.1
8.0
12.0
Q1
LMV358IDRG4
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
LMV358IPWR
TSSOP
PW
8
2000
330.0
12.4
7.0
3.6
1.6
8.0
12.0
Q1
LMV358IPWR
TSSOP
PW
8
2000
330.0
12.4
7.0
3.6
1.6
8.0
12.0
Q1
LMV358IPWRG4
TSSOP
PW
8
2000
330.0
12.4
7.0
3.6
1.6
8.0
12.0
Q1
LMV358QDDUR
VSSOP
DDU
8
3000
180.0
8.4
2.25
3.35
1.05
4.0
8.0
Q3
LMV358QDGKR
VSSOP
DGK
8
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LMV358QDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
LMV358QPWR
TSSOP
PW
8
2000
330.0
12.4
7.0
3.6
1.6
8.0
12.0
Q1
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LMV321IDBVR
SOT-23
DBV
5
3000
180.0
180.0
18.0
LMV321IDBVT
SOT-23
DBV
5
250
180.0
180.0
18.0
LMV321IDCKR
SC70
DCK
5
3000
180.0
180.0
18.0
LMV321IDCKR
SC70
DCK
5
3000
205.0
200.0
33.0
LMV321IDCKT
SC70
DCK
5
250
205.0
200.0
33.0
LMV321IDCKT
SC70
DCK
5
250
180.0
180.0
18.0
LMV324IDR
SOIC
D
14
2500
333.2
345.9
28.6
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Dec-2016
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LMV324IDR
SOIC
D
14
2500
367.0
367.0
38.0
LMV324IDR
SOIC
D
14
2500
364.0
364.0
27.0
LMV324IDRG4
SOIC
D
14
2500
333.2
345.9
28.6
LMV324IPWR
TSSOP
PW
14
2000
367.0
367.0
35.0
LMV324IPWR
TSSOP
PW
14
2000
364.0
364.0
27.0
LMV324IPWRG4
TSSOP
PW
14
2000
367.0
367.0
35.0
LMV324QDR
SOIC
D
14
2500
367.0
367.0
38.0
LMV324QPWR
TSSOP
PW
14
2000
367.0
367.0
35.0
LMV358IDDUR
VSSOP
DDU
8
3000
202.0
201.0
28.0
LMV358IDGKR
VSSOP
DGK
8
2500
358.0
335.0
35.0
LMV358IDR
SOIC
D
8
2500
340.5
338.1
20.6
LMV358IDR
SOIC
D
8
2500
367.0
367.0
35.0
LMV358IDR
SOIC
D
8
2500
364.0
364.0
27.0
LMV358IDRG4
SOIC
D
8
2500
340.5
338.1
20.6
LMV358IPWR
TSSOP
PW
8
2000
364.0
364.0
27.0
LMV358IPWR
TSSOP
PW
8
2000
367.0
367.0
35.0
LMV358IPWRG4
TSSOP
PW
8
2000
367.0
367.0
35.0
LMV358QDDUR
VSSOP
DDU
8
3000
202.0
201.0
28.0
LMV358QDGKR
VSSOP
DGK
8
2500
358.0
335.0
35.0
LMV358QDR
SOIC
D
8
2500
340.5
338.1
20.6
LMV358QPWR
TSSOP
PW
8
2000
367.0
367.0
35.0
Pack Materials-Page 3
PACKAGE OUTLINE
PW0008A
TSSOP - 1.2 mm max height
SCALE 2.800
SMALL OUTLINE PACKAGE
C
6.6
TYP
6.2
SEATING PLANE
PIN 1 ID
AREA
A
0.1 C
6X 0.65
8
1
3.1
2.9
NOTE 3
2X
1.95
4
5
B
4.5
4.3
NOTE 4
SEE DETAIL A
8X
0.30
0.19
0.1
C A
1.2 MAX
B
(0.15) TYP
0.25
GAGE PLANE
0 -8
0.15
0.05
0.75
0.50
DETAIL A
TYPICAL
4221848/A 02/2015
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.
5. Reference JEDEC registration MO-153, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
PW0008A
TSSOP - 1.2 mm max height
SMALL OUTLINE PACKAGE
8X (1.5)
8X (0.45)
SYMM
1
8
(R0.05)
TYP
SYMM
6X (0.65)
5
4
(5.8)
LAND PATTERN EXAMPLE
SCALE:10X
SOLDER MASK
OPENING
METAL
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
0.05 MAX
ALL AROUND
0.05 MIN
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
NOT TO SCALE
4221848/A 02/2015
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
PW0008A
TSSOP - 1.2 mm max height
SMALL OUTLINE PACKAGE
8X (1.5)
8X (0.45)
SYMM
(R0.05) TYP
1
8
SYMM
6X (0.65)
5
4
(5.8)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:10X
4221848/A 02/2015
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated

Open as PDF

Similar pages