DS16F95QML www.ti.com SNOSAN0B – SEPTEMBER 2005 – REVISED APRIL 2013 DS16F95QML EIA-485/EIA-422A Differential Bus Transceiver Check for Samples: DS16F95QML FEATURES DESCRIPTION • • • • • The DS16F95 Differential Bus Transceiver is a monolithic integrated circuit designed for bidirectional data communication on balanced multipoint bus transmission lines. The transceiver meets EIA standard RS-485 as well as RS-422A. 1 2 • • • • • • • Radiation Ensured 300 krad(Si) Meets EIA-485 and EIA-422A Meets SCSI-1 (5 MHZ) Specifications Designed for Multipoint Transmission Wide Positive and Negative Input/Output Bus Voltage Ranges Thermal Shutdown Protection Driver Positive and Negative Current-Limiting High Impedance Receiver Input Receiver Input Hysteresis of 50 mV Typical Operates from Single 5.0V Supply Reduced Power Consumption Pin Compatible with DS3695 and SN75176A The DS16F95 offers improved performance due to the use of state-of-the-art L-FAST bipolar technology. The L-FAST technology allows for higher speeds and lower currents by utilizing extremely short gate delay times. Thus, the DS16F95QML features lower power, extended temperature range and improved specifications. The DS16F95 combines a TRI-STATE differential line driver and a differential input line receiver, both of which operate from a single 5.0V power supply. The driver and receiver have an active Enable that can be externally connected to function as a direction control. The driver differential outputs and the receiver differential inputs are internally connected to form differential input/output (I/O) bus ports that are designed to offer minimum loading to the bus whenever the driver is disabled or when VCC = 0V. These ports feature wide positive and negative common mode voltage ranges, making the device suitable for multipoint applications in noisy environments. The driver is designed to accommodate loads of up to 60 mA of sink or source current and features positive and negative current limiting in addition to thermal shutdown for protection from line fault conditions. The DS16F95 can be used in transmission applications employing the DS96F172 and DS96F174 quad differential line drivers and DS96F173 and DS96F175 quad differential receivers. line the the line 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2005–2013, Texas Instruments Incorporated DS16F95QML SNOSAN0B – SEPTEMBER 2005 – REVISED APRIL 2013 www.ti.com Connection Diagram Figure 1. 20-Lead Ceramic Leadless Chip Carrier Figure 2. 8-Lead Dual-In-Line Package Figure 3. 10-Lead Flatpak Package Logic Diagram Function Tables Table 1. Driver (1) (1) 2 Driver Input Enable DI DE A Outputs B H H H L L H L H X L Z Z H = High Level, L = Low Level, X = Immaterial, Z = High Impedance (Off) Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: DS16F95QML DS16F95QML www.ti.com SNOSAN0B – SEPTEMBER 2005 – REVISED APRIL 2013 Table 2. Receiver (1) (1) Differential Inputs Enable Output A–B RE RO H VID ≥ 0.2V L VID ≤ −0.2V L L X H Z H = High Level, L = Low Level, X = Immaterial, Z = High Impedance (Off) Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: DS16F95QML 3 DS16F95QML SNOSAN0B – SEPTEMBER 2005 – REVISED APRIL 2013 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) -65°C ≤ TA ≤ +175°C Storage Temperature Range Lead Temperature Maximum Power Dissipation at 25°C (2) (Soldering, 60 sec.) 300°C LCCC 'NAJ' Package 1800 mW CDIP 'NAB' Package 1274 mW CLGA 'NAD' Package 725 mW Supply Voltage 7.0V Input Voltage (Bus Terminal) +15V/−10V Enable Input Voltage 5.5V Junction Temperature (TJ) +175°C θJA Thermal Resistance θJC LCCC 'NAJ' Package 83°C/W @ 0.5W CDIP 'NAB' Package 118°C/W @ 1.0W CLGA 'NAD' Package 207°C/W @ 0.5W LCCC 'NAJ' Package 17°C/W CDIP 'NAB' Package 14°C/W CLGA 'NAD' Package 18°C/W ESD Tolerance (3) (1) (2) (3) 500V Absolute Maximum Ratings are those values beyond which the safety of the device cannot be ensured. They are not meant to imply that the devices should be operated at these limits. The tables of Electrical Characteristics provide conditions for actual device operation. Above TA = 25°C, derate NAJ package 12.1mW°C, NAB package 8.5 mW/°C, NAD package 4.8mW/°C. Human body model, 1.5kΩ in series with 100pF Recommended Operating Conditions Supply Voltage (VCC) Voltage at Any Bus Terminal 4.50 to 5.50V (Separately or Common Mode) (VI or VCM) Differential Input Voltage (VID) Output Current HIGH (IOH) Driver Output Current LOW (IOL) -7.0V to ±12V Driver -60mA Receiver -400μA Driver Receiver Operating Temperature (TA) 4 -7.0V to +12V 60mA 16mA -55°C to +125°C Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: DS16F95QML DS16F95QML www.ti.com SNOSAN0B – SEPTEMBER 2005 – REVISED APRIL 2013 Quality Conformance Inspection MIL-STD-883, Method 5005 - Group A Subgroup Description Temp (°C) 1 Static tests at +25 2 Static tests at +125 3 Static tests at -55 4 Dynamic tests at +25 5 Dynamic tests at +125 6 Dynamic tests at -55 7 Functional tests at +25 8A Functional tests at +125 8B Functional tests at -55 9 Switching tests at +25 10 Switching tests at +125 11 Switching tests at -55 DC - Driver Electrical Characteristics (1) The following conditions apply to all parameters, unless otherwise specified. VCC = 5.5V Symbol VOD1 VOD2 Parameter Differential Vout Differential Vout (See Figure 4) ΔVOD Change In Differential Vout Δ VOC Change In Common Mode Vout VOC Common Mode Vout IIH Logical "1" Input Current IO Output Current Conditions Max Unit Sub-group VCC = 5.5V, IO = 0A, VIN = .8V Notes 6 V 1, 2, 3 VCC = 5.5V, IO = 0A, VIN = 2V 6 V 1, 2, 3 V 1, 2, 3 VCC = 4.5V, RL = 100Ω 2 VCC = 4.5V, RL = 54Ω 1.5 V 1, 2, 3 VCC = 4.5V, RL = 100Ω -200 200 mV 1, 2, 3 -200 200 mV 1, 2, 3 -200 200 mV 1, 2, 3 -200 200 mV 1, 2, 3 3 V 1, 2, 3 VCC = 4.5V, RL = 54Ω VCC = 4.5V, RL = 100Ω VCC = 4.5V, RL = 54Ω See (2) See (2) RL = 100Ω RL = 54Ω 3 V 1, 2, 3 VI = 2.4V 20 uA 1, 2, 3 Output Disable, VO = 12V 1 mA 1, 2, 3 mA 1, 2, 3 mA 1, 2, 3 mA 1, 2, 3 Output Disable, VO = -7V (2) (3) See (3) -0.8 See (3) -0.8 VCC = 0, Output Disable, VO = 12V VCC = 0, Output Disable, VO = -7V (1) Min 1 Pre and post irradiation limits are identical to those listed under A C and DC electrical characteristics. These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters are ensured only for the conditions as specified in MIL-STD 883, Method 1019, condition A. Δ|VOD| and Δ|VOC| are the changes in magnitude of VOD and VOC, respectively, that occur when the input is changed from a high level to a low level. Negative sign of the limits indicates the direction of the current flow only. Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: DS16F95QML 5 DS16F95QML SNOSAN0B – SEPTEMBER 2005 – REVISED APRIL 2013 www.ti.com DC - Driver Electrical Characteristics(1) (continued) The following conditions apply to all parameters, unless otherwise specified. VCC = 5.5V Symbol Parameter Conditions Notes Min VIN = 3V, VOUT = VCC VIN = 3V, VOUT = -7V VIN = 3V, VOUT = 0V IOS Output Short Circuit Unit Sub-group 150 mA 1, 2, 3 -250 mA 1, 2, 3 -150 mA 1, 2, 3 VIN = 3V, VOUT = 12V 250 mA 1, 2, 3 VIN = 0V, VOUT = 12V 250 mA 1, 2, 3 VIN = 0V, VOUT = VCC 150 mA 1, 2, 3 -250 mA 1, 2, 3 -150 mA 1, 2, 3 3 V 1, 2, 3 V 1, 2, 3 V 1, 2, 3 VIN = 0V, VOUT = -7V VIN = 0V, VOUT = 0V VOH Logical "1" Output Voltage VCC = 4.5V, IO = -20mA VOL Logical "0" Output Voltage VCC = 4.5V, IO = 20mA VOD3 Differential Vout VCM = -7V to 12V (4) See (4) Max See (4) 2 1 Negative sign of the limits indicates the direction of the current flow only. DC - Receiver Electrical Characteristics (1) The following conditions apply to all parameters, unless otherwise specified. VCC = 5.5V Symbol Parameter VOH Logical "1" Output Voltage (See Figure 5) VOL Logical "0" Output Voltage (See Figure 5) Conditions Notes VCC = 4.5V, VLD = 200mV, IOH = -400uA Min 2.5 Logical "1" Input Current VCC = 4.5V, VLD = -200mV, IOL = 16mA .5 V 1, 2, 3 1 mA 1, 2, 3 mA 1, 2, 3 mA 1, 2, 3 mA 1, 2, 3 VCC = 0V, Untested Input = 0V, VI = 12V See (2) See (2) VCC = 0V, Untested Input = 0V, VI = 12V VCC = 0V, Untested Input = 0V, VI = -7V IOZ (1) (2) (3) 6 High Impedance State -.8 1 -.8 VI = 2.7V (Receiver) Untested Input = 0V, VI = -7V Input Resistance 1, 2, 3 1, 2, 3 Untested Input = 0V, VI = 12V RIN V V VCC = 0V, Untested Input = 0V, VI = -7V IIH Sub-group .45 Untested Input = 0V, VI = -7V Line Input Current Unit VCC = 4.5V, VLD = -200mV, IOL = 8mA Untested Input = 0V, VI = 12V II Max 20 See (3) uA 1, 2, 3 10 KΩ 1, 2, 3 10 KΩ 1, 2, 3 10 KΩ 1, 2, 3 10 KΩ 1, 2, 3 See (3) VI = 0.4V -20 20 uA 1, 2, 3 VI = 2.4V -20 20 uA 1, 2, 3 Pre and post irradiation limits are identical to those listed under A C and DC electrical characteristics. These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters are ensured only for the conditions as specified in MIL-STD 883, Method 1019, condition A. Negative sign of the limits indicates the direction of the current flow only. RIN is guaranteed by testing “Line Input Current” (II). Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: DS16F95QML DS16F95QML www.ti.com SNOSAN0B – SEPTEMBER 2005 – REVISED APRIL 2013 DC - Receiver Electrical Characteristics(1) (continued) The following conditions apply to all parameters, unless otherwise specified. VCC = 5.5V Symbol IOS Parameter Output Short Circuit Differential Input High Threshold VTH Differential Input Low Threshold VT1 VTH+ - (VTH-) Hyteresis Conditions Notes VIN = 1V, VOUT = 0V Min Max Unit Sub-group -85 -15 mA 1, 2, 3 VCC = 4.5V, VO = 2.5V, VCM = 12V & 0V & -7V, IO = -.4mA .2 V 1, 2, 3 VCC = 5.5V, Vo = 2.5V, VCM = 12V & 0V & -7V, IO = -.4mA .2 V 1, 2, 3 VCC = 4.5V, VO = .5V, VCM = 12V & 0V & -7V, IO = 8mA -.2 V 1, 2, 3 VCC = 5.5V, VO = .5V, VCM = 12V & 0V & -7V, IO = 8mA -.2 V 1, 2, 3 VCC = 4.5V, VCM = 0V 35 mV 1, 2, 3 VCC = 5.5V, VCM = 0V 35 mV 1, 2, 3 Max Unit Sub-group 25 mA 1, 2, 3 28 DC - Both Driver and Receiver Electrical Characteristics (1) The following conditions apply to all parameters, unless otherwise specified. VCC = 5.5V Symbol Parameter Conditions ICC Supply Current ICC Both Disable RE = 2V, DE = .8V ICC Supply Current ICC Both Enable RE =.8V, DE = 2V VIC Input Clamp Volt II = -18mA VIH Logical "1" Input Voltage VIL Logical "0" Input Voltage VIH Logical "1" Enable Input Voltage VIL Logical "0" Enable Input Voltage I IL Logical "0" Input Current (1) (2) Notes Min mA 1, 2, 3 -1.3 V 1, 2, 3 2 V 1, 2, 3 V 1, 2, 3 V 1, 2, 3 V 1, 2, 3 uA 1, 2, 3 .8 2 .8 See (2) VI = 0.4V -50 Pre and post irradiation limits are identical to those listed under A C and DC electrical characteristics. These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters are ensured only for the conditions as specified in MIL-STD 883, Method 1019, condition A. Negative sign of the limits indicates the direction of the current flow only. AC - Driver Electrical Characteristics (1) The following conditions apply to all parameters, unless otherwise specified. VCC = 5V, PRR = 1MHZ, TR ≤ TF ≤ 6nS, 50% duty cycle, AMP = 3V, VLO, ZOUT = 50Ω Symbol tDD Parameter Conditions Notes Differential Output Delay Time (See Figure 6) RL = 60Ω See (2) tTD Differential Output Transition Time (See Figure 6) RL = 60Ω See (2) (3) tPLH Propagation Delay Time Low to High (See Figure 7) RL = 27Ω tPHL Propagation Delay Time high to Low (See Figure 7) RL = 27Ω tPZH Output Enable Time to H (See Figure 8) RL = 110Ω tPZL Output Enable Time to L (See Figure 9) (1) (2) (3) RL = 110Ω Min Max Unit 8 25 nS Sub-group 9 8 30 nS 10, 11 8 25 nS 9 8 30 nS 10, 11 6 18 nS 9 6 25 nS 10, 11 6 18 nS 9 6 25 nS 10, 11 35 nS 9 45 nS 10, 11 40 nS 9 50 nS 10, 11 Pre and post irradiation limits are identical to those listed under A C and DC electrical characteristics. These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters are ensured only for the conditions as specified in MIL-STD 883, Method 1019, condition A. Rise time 20% to 80%, Fall time 80% to 20%. tTD = Non-inverting output rise time + inverting output fall time / 2, Non-inverting output fall time + inverting output rise time / 2. Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: DS16F95QML 7 DS16F95QML SNOSAN0B – SEPTEMBER 2005 – REVISED APRIL 2013 www.ti.com AC - Driver Electrical Characteristics(1) (continued) The following conditions apply to all parameters, unless otherwise specified. VCC = 5V, PRR = 1MHZ, TR ≤ TF ≤ 6nS, 50% duty cycle, AMP = 3V, VLO, ZOUT = 50Ω Symbol Parameter tPHZ Output Disable Time to H (See Figure 8) tPLZ Output Disable Time to L (See Figure 9) TSKEW Differential Output Skew Time (See Figure 6) Conditions Notes Min Max Unit Sub-group 30 nS 9 40 nS 10, 11 30 nS 9 40 nS 10, 11 6 nS 9 12 nS 10, 11 RL = 110Ω RL = 110Ω AC - Receiver Electrical Characteristics (1) The following conditions apply to all parameters, unless otherwise specified. VCC = 5V, PRR = 1MHZ, TR ≤ TF ≤ 6nS, 50% duty cycle, AMP = 3V, VLO, ZOUT = 50Ω Symbol Parameter Conditions tPLH Propagation Delay Time Low to High (See Figure 10) tPHL Propagation Delay Time High to Low (See Figure 10) CL = 15pF tPZH Output Enable Time to H (See Figure 11) CL = 15pF tPZL Output Enable Time to L (See Figure 11) CL = 15pF |tPLH - tPHL| Output to Output Delay Time (See Figure 10) CL = 15pF CL = 20pF tPHZ Output Disable Time From H (See Figure 11) CL = 5pF tPLZ (1) (2) 8 Output Disable Time From L (See Figure 11) Notes See (2) See (2) CL = 5pF Min Max Unit Sub-group 10 27 nS 9 10 38 nS 10, 11 10 27 nS 9 10 38 nS 10, 11 20 nS 9 30 nS 10, 11 20 nS 9 30 nS 10, 11 8 nS 9 16 nS 10, 11 30 nS 9 40 nS 10, 11 20 nS 9 30 nS 10, 11 20 nS 9 30 nS 10, 11 Pre and post irradiation limits are identical to those listed under A C and DC electrical characteristics. These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters are ensured only for the conditions as specified in MIL-STD 883, Method 1019, condition A. Testing at 20pF assures conformance to spec at 5pF. Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: DS16F95QML DS16F95QML www.ti.com SNOSAN0B – SEPTEMBER 2005 – REVISED APRIL 2013 Parameter Measurement Information Figure 4. Driver VOD and VOC(1) Figure 5. Receiver VOH and VOL tSKEW = |tPLHD–tPHLD| Figure 6. Driver Differential Output Delay and Transition Times(2)(3) Figure 7. Driver Propagation Times(2)(4) Figure 8. Driver Enable and Disable Times (tZH, tHZ)(2)(3)(4) (1) All diodes are 1N916 or equivalent. (2) The input pulse is supplied by a generator having the following characteristics: PRR = 1.0 MHz, 50% duty cycle, tr ≤ 6.0 ns, tf ≤ 6.0 ns, ZO = 50Ω. (3) DS16F95 Driver enable is Active-High. (4) CL includes probe and stray capacitance. Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: DS16F95QML 9 DS16F95QML SNOSAN0B – SEPTEMBER 2005 – REVISED APRIL 2013 www.ti.com Figure 9. Driver Enable and Disable Times (tZL, tLZ)(1)(2)(3) Figure 10. Receiver Propagation Delay Times(1)(3) Figure 11. Receiver Enable and Disable Times(1)(3)(4) (1) The input pulse is supplied by a generator having the following characteristics: PRR = 1.0 MHz, 50% duty cycle, tr ≤ 6.0 ns, tf ≤ 6.0 ns, ZO = 50Ω. (2) DS16F95 Driver enable is Active-High. (3) CL includes probe and stray capacitance. (4) All diodes are 1N916 or equivalent. 10 Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: DS16F95QML DS16F95QML www.ti.com SNOSAN0B – SEPTEMBER 2005 – REVISED APRIL 2013 Typical Application The line should be terminated at both ends in its characteristic impedance, typically 120Ω. Stub lengths off the main line should be kept as short as possible. Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: DS16F95QML 11 DS16F95QML SNOSAN0B – SEPTEMBER 2005 – REVISED APRIL 2013 www.ti.com REVISION HISTORY Date Released 12 Revision Section Changes 9/23/2005 A New Release, Corporate format 1 MDS data sheet converted into Corporate data sheet format. MDS data sheet MNDS16F95-X-RH, Rev. 0A1 will be Archived. 10/26/2010 B Features, Ordering Table, Connection Diagrams W pkg, Absolute Ratings, Electricals - DC Receiver VT1, AC Driver conditions, Physical Dimensions Mkt drawing Update with current device information and format. Correction to rad info., Code K NSID's removed, removed reference to WG pkg, typo correction to conditions, Removed WG pkg drawing. Revision A will be Archived 4/12/2013 B All Changed layout of National Data Sheet to TI format. Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: DS16F95QML PACKAGE OPTION ADDENDUM www.ti.com 20-Jul-2016 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) 5962-89615012A ACTIVE LCCC NAJ 20 50 TBD Call TI Call TI -55 to 125 DS16F95E /883 Q 5962-89615 012A ACO 012A >T 5962-8961501PA ACTIVE CDIP NAB 8 40 TBD Call TI Call TI -55 to 125 DS16F95J/883 5962-89615 01PA Q ACO (DS9638J/883 ~ DS9638J/883) 01PA Q >T 5962F8961501VHA ACTIVE CFP NAD 10 19 TBD Call TI Call TI -55 to 125 DS16F95 WFQMLV Q 5962F89615 01VHA ACO 01VHA >T DS16F95 MDR ACTIVE DIESALE Y 0 34 Green (RoHS & no Sb/Br) Call TI Level-1-NA-UNLIM -55 to 125 DS16F95 MDS ACTIVE DIESALE Y 0 Green (RoHS & no Sb/Br) Call TI Level-1-NA-UNLIM -55 to 125 DS16F95E/883 ACTIVE LCCC NAJ 20 50 TBD Call TI Call TI -55 to 125 DS16F95E /883 Q 5962-89615 012A ACO 012A >T DS16F95J/883 ACTIVE CDIP NAB 8 40 TBD Call TI Call TI -55 to 125 DS16F95J/883 5962-89615 01PA Q ACO (DS9638J/883 ~ DS9638J/883) 01PA Q >T DS16F95W/883 ACTIVE CFP NAD 10 19 TBD Call TI Call TI -55 to 125 DS16F95W /883 Q ACO /883 Q >T DS16F95WFQMLV ACTIVE CFP NAD 10 19 TBD Call TI Call TI -55 to 125 DS16F95 WFQMLV Q 5962F89615 Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 20-Jul-2016 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) 01VHA ACO 01VHA >T (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF DS16F95QML, DS16F95QML-SP : Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com 20-Jul-2016 • Military: DS16F95QML • Space: DS16F95QML-SP NOTE: Qualified Version Definitions: • Military - QML certified for Military and Defense Applications • Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application Addendum-Page 3 MECHANICAL DATA NAB0008A J08A (Rev M) www.ti.com MECHANICAL DATA NAJ0020A E20A (Rev F) www.ti.com MECHANICAL DATA NAD0010A W10A (Rev H) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2016, Texas Instruments Incorporated