LTC3786 Low IQ Synchronous Boost Controller Description Features n n n n n n n n n n n n n n Synchronous Operation For Highest Efficiency and Reduced Heat Dissipation Wide VIN Range: 4.5V to 38V (40V Abs Max) and Operates Down to 2.5V After Start-Up Output Voltages Up to 60V ±1% 1.2V Reference Voltage RSENSE or Inductor DCR Current Sensing 100% Duty Cycle Capability for Synchronous MOSFET Low Quiescent Current: 55µA Phase-Lockable Frequency (75kHz to 850kHz) Programmable Fixed Frequency (50kHz to 900kHz) Adjustable Output Voltage Soft-Start Power Good Output Voltage Monitor Low Shutdown Current IQ: <8µA Internal 5.4V LDO for Gate Drive Supply Thermally Enhanced 16-Pin 3mm × 3mm QFN and MSOP Packages Applications n n n n Industrial and Automotive Power Supplies Automotive Start-Stop Systems Medical Devices High Voltage Battery-Powered Systems The LTC®3786 is a high performance synchronous boost converter controller that drives all N-channel power MOSFETs. Synchronous rectification increases efficiency, reduces power losses and eases thermal requirements, allowing the LTC3786 to be used in high power boost applications. A 4.5V to 38V input supply range encompasses a wide range of system architectures and battery chemistries. When biased from the output of the boost converter or another auxiliary supply, the LTC3786 can operate from an input supply as low as 2.5V after start-up. The 55µA no-load quiescent current extends operating run time in battery-powered systems. The operating frequency can be set for a 50kHz to 900kHz range or synchronized to an external clock using the internal PLL. The LTC3786 also features a precision 1.2V reference and a power good output indicator. The SS pin ramps the output voltage during start-up. The PLLIN/MODE pin selects among Burst Mode® operation, pulse-skipping mode or continuous inductor current mode at light loads. L, LT, LTC, LTM, Burst Mode, OPTI-LOOP, Linear Technology and the Linear logo are registered trademarks and No RSENSE is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U. S. Patents, including 5408150, 5481178, 5705919, 5929620, 6177787, 6498466, 6580258, 6611131. Typical Application 12V to 24V/5A Synchronous Boost Converter Efficiency and Power Loss vs Load Current VIN 4.5V TO 24V VBIAS SENSE+ 100 LTC3786 SS 8.66k 220pF 12.1k ITH 3.3µH TG SW 0.1µF 220µF VOUT 24V 5A BOOST INTVCC GND 70 BURST EFFICIENCY 1000 BURST LOSS 60 100 50 40 10 30 VIN = 12V 1 VOUT = 24V Burst Mode OPERATION 10 FIGURE 8 CIRCUIT 0 0.1 0.1 1 10 0.00001 0.0001 0.001 0.01 OUTPUT CURRENT (A) 20 BG VFB 232k 80 EFFICIENCY (%) 15nF 220µF SENSE– POWER LOSS (mW) 0.1µF PGOOD PLLIN/MODE RUN FREQ 4mΩ 10000 90 4.7µF 3786 TA01a 3786 TA01b 3786fa 1 LTC3786 Absolute Maximum Ratings (Notes 1, 3) VBIAS......................................................... –0.3V to 40V BOOST.........................................................–0.3V to 71V SW.............................................................. –0.3V to 65V RUN.............................................................. –0.3V to 8V Maximum Current Sourced into Pin from Source >8V...............................................100µA PGOOD, PLLIN/MODE................................... –0.3V to 6V INTVCC, (BOOST – SW)................................ –0.3V to 6V SENSE+, SENSE–......................................... –0.3V to 40V SENSE+ – SENSE–...................................... –0.3V to 0.3V SS, ITH, FREQ, VFB............................... –0.3V to INTVCC Operating Junction Temperature Range....–40°C to 125°C Storage Temperature Range................... –65°C to 125°C Lead Temperature (Soldering, 10 sec) MSE Package Only............................................. 300°C Pin Configuration INTVCC 16 15 14 13 PGOOD SW TG BOOST VBIAS INTVCC BG GND SW 1 12 BG PGOOD 2 11 GND 17 GND VFB 3 10 RUN SENSE+ 4 6 7 FREQ 8 PLLIN/ MODE 5 SS MSE PACKAGE 16-LEAD PLASTIC MSOP TJMAX = 125°C, θJA = 40°C/W, θJC = 10°C/W EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB 9 ITH 17 GND 16 15 14 13 12 11 10 9 SENSE– 1 2 3 4 5 6 7 8 VBIAS TOP VIEW VFB SENSE+ SENSE– ITH SS PLLIN/MODE FREQ RUN BOOST TG TOP VIEW UD PACKAGE 16-LEAD (3mm × 3mm) PLASTIC QFN TJMAX = 125°C, θJA = 68°C/W, θJC = 4.2°C/W EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3786EMSE#PBF LTC3786EMSE#TRPBF 3786 16-Lead Plastic MSOP –40°C to 125°C LTC3786IMSE#PBF LTC3786IMSE#TRPBF 3786 16-Lead Plastic MSOP –40°C to 125°C LTC3786EUD#PBF LTC3786EUD#TRPBF LFXW 16-Lead (3mm × 3mm) Plastic QFN –40°C to 125°C LTC3786IUD#PBF LTC3786IUD#TRPBF LFXW 16-Lead (3mm × 3mm) Plastic QFN –40°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 3786fa 2 LTC3786 Electrical Characteristics The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25°C. VBIAS = 12V, unless otherwise noted (Note 2). SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Main Control Loop VBIAS Chip Bias Voltage Operating Range 4.5 VFB Regulated Feedback Voltage ITH = 1.2V (Note 4) IFB Feedback Current (Note 4) VREFLNREG Reference Line Voltage Regulation VBIAS = 6V to 38V VLOADREG Output Voltage Load Regulation (Note 4) Measured in Servo Loop; ∆ITH Voltage = 1.2V to 0.7V Measured in Servo Loop; ∆ITH Voltage = 1.2V to 2V gm Error Amplifier Transconductance IQ Input DC Supply Current (Note 5) Pulse-Skipping or Forced Continuous Mode RUN = 5V; VFB = 1.25V (No Load) Sleep Mode RUN = 5V; VFB = 1.25V (No Load) Shutdown RUN = 0V V 1.200 1.212 V ±5 ±50 nA 0.002 0.02 %/V l 0.01 0.1 % l –0.01 –0.1 % l 1.188 38 ITH = 1.2V 2 0.8 55 8 mmho 80 20 mA µA µA UVLO INTVCC Undervoltage Lockout Thresholds VINTVCC Ramping Up VINTVCC Ramping Down l l 3.6 4.1 3.8 4.3 V V VRUN RUN Pin On Threshold VRUN Rising l 1.18 1.28 1.38 V VRUNHYS RUN Pin Hysteresis 100 mV IRUNHYS RUN Pin Hysteresis Current VRUN > 1.28V 4.5 µA IRUN RUN Pin Current VRUN < 1.28V 0.5 µA ISS Soft-Start Charge Current VSS = 0V VSENSE(MAX) Maximum Current Sense Threshold VFB = 1.1V VSENSE(CM) SENSE Pins Common Mode Range (BOOST Converter Input Supply Voltage VIN) ISENSE+ SENSE+ Pin Current VFB = 1.1V ISENSE– SENSE– Pin Current VFB = 1.1V tr(TG) Top Gate Rise Time CLOAD = 3300pF (Note 6) 20 ns tf(TG) Top Gate Fall Time CLOAD = 3300pF (Note 6) 20 ns tr(BG) Bottom Gate Rise Time CLOAD = 3300pF (Note 6) 20 ns tf(BG) Bottom Gate Fall Time CLOAD = 3300pF (Note 6) 20 ns RUP(TG) Top Gate Pull-Up Resistance 1.2 Ω RDN(TG) Top Gate Pull-Down Resistance 1.2 Ω RUP(BG) Bottom Gate Pull-Up Resistance 1.2 Ω RDN(BG) Bottom Gate Pull-Down Resistance 1.2 Ω tD(TG/BG) Top Gate Off to Bottom Gate On Switch-On Delay Time CLOAD = 3300pF (Each Driver) 80 ns tD(BG/TG) Bottom Gate Off to Top Gate On Switch-On Delay Time CLOAD = 3300pF (Each Driver) 80 ns DFMAXBG Maximum BG Duty Factor 96 % tON(MIN) Minimum BG On-Time 110 ns l 7 10 13 µA 68 75 82 mV 38 V 300 µA ±1 µA 2.5 (Note 7) 200 3786fa 3 LTC3786 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VBIAS = 12V, unless otherwise noted (Note 2). SYMBOL PARAMETER CONDITIONS MIN 5.2 TYP MAX UNITS INTVCC Linear Regulator VINTVCC(VIN) Internal VCC Voltage 6V < VBIAS < 38V VLDO INT INTVCC Load Regulation ICC = 0mA to 50mA 5.4 5.6 V 0.5 2 % Oscillator and Phase-Locked Loop fPROG Programmable Frequency RFREQ = 25k RFREQ = 60k RFREQ = 100k 335 105 400 760 465 kHz kHz kHz fLOW Lowest Fixed Frequency VFREQ = 0V 320 350 380 kHz fHIGH Highest Fixed Frequency VFREQ = INTVCC 485 535 585 kHz fSYNC Synchronizable Frequency PLLIN/MODE = External Clock 850 kHz l 75 PGOOD Output VPGL PGOOD Voltage Low IPGOOD = 2mA IPGOOD PGOOD Leakage Current VPGOOD = 5V VPG PGOOD Trip Level VFB with Respect to Set Regulated Voltage VFB Ramping Negative Hysteresis VFB Ramping Positive Hysteresis tPGOOD(DELAY) PGOOD Delay 0.2 –12 8 –10 2.5 10 2.5 0.4 V ±1 µA –8 % % % % 12 PGOOD Going High to Low 25 µs VSW = 12V; VBOOST – VSW = 4.5V; FREQ = 0V, Forced Continuous or Pulse-Skipping Mode 85 µA BOOST Charge Pump IBOOST BOOST Charge Pump Available Output Current Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC3786 is tested under pulsed load conditions such that TJ ≈ TA. The LTC3786E is guaranteed to meet specifications from 0°C to 85°C junction temperature. Specifications over the –40°C to 125°C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LTC3786I is guaranteed over the –40°C to 125°C operating junction temperature range. Note that the maximum ambient temperature consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal impedance and other environmental factors. The junction temperature (TJ in °C) is calculated from the ambient temperature (TA in °C) and power dissipation (PD in Watts) according to the formula: TJ = TA + (PD • θJA) where θJA = 68°C for the QFN package and θJA = 40°C for the MSOP package. Note 3: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. The maximum rated junction temperature will be exceeded when this protection is active. Continuous operation above the specified absolute maximum operating junction temperature may impair device reliability or permanently damage the device. Note 4: The LTC3786 is tested in a feedback loop that servos VFB to the output of the error amplifier while maintaining ITH at the midpoint of the current limit range. Note 5: Dynamic supply current is higher due to the gate charge being delivered at the switching frequency. Note 6: Rise and fall times are measured using 10% and 90% levels. Delay times are measured using 50% levels. Note 7: see Minimum On-Time Considerations in the Applications Information section. 3786fa 4 LTC3786 Typical Performance Characteristics Efficiency and Power Loss vs Output Current Efficiency and Power Loss vs Output Current 100 10000 100 90 80 1000 40 30 20 10 0 0.01 0.1 1 OUTPUT CURRENT (A) 10 1 10 0.1 EFFICIENCY (%) 100 VIN = 12V VOUT = 24V FIGURE 8 CIRCUIT CCM EFFICIENCY CMM LOSS BURST EFFICIENCY BURST LOSS PULSE-SKIPPING EFFICIENCY PULSE-SKIPPING LOSS 50 80 70 BURST EFFICIENCY 60 100 50 40 10 30 VIN = 12V 1 VOUT = 24V Burst Mode OPERATION 10 FIGURE 8 CIRCUIT 0 0.1 0.1 1 10 0.00001 0.0001 0.001 0.01 OUTPUT CURRENT (A) 20 3786 G01 100 ILOAD = 2A FIGURE 8 CIRCUIT 99 EFFICIENCY (%) 98 VOUT = 12V VOUT = 24V 96 95 INDUCTOR CURRENT 5A/DIV LOAD STEP 2A/DIV INDUCTOR CURRENT 5A/DIV VOUT 500mV/DIV VOUT 500mV/DIV VIN = 12V 200µs/DIV VOUT = 24V LOAD STEP FROM 200mA TO 2.5A FIGURE 8 CIRCUIT 94 0 5 10 Load Step Burst Mode Operation LOAD STEP 2A/DIV 97 93 3786 G02 Load Step Forced Continuous Mode Efficiency vs Input Voltage 15 20 1000 BURST LOSS POWER LOSS (mW) 60 POWER LOSS (mW) 70 EFFICIENCY (%) 10000 90 3786 G04 VIN = 12V 200µs/DIV VOUT = 24V LOAD STEP FROM 200mA TO 2.5A FIGURE 8 CIRCUIT 3786 G05 25 INPUT VOLTAGE (V) 3786 G03 Load Step Pulse-Skipping Mode Inductor Current at Light Load LOAD STEP 2A/DIV INDUCTOR CURRENT 5A/DIV Soft Start-Up FORCED CONTINUOUS MODE VOUT 5V/DIV Burst Mode OPERATION 5A/DIV PULSESKIPPING MODE VOUT 500mV/DIV VIN = 12V 200µs/DIV VOUT = 24V LOAD STEP FROM 200mA TO 2.5A FIGURE 8 CIRCUIT 3786 G06 0V VIN = 12V 5µs/DIV VOUT = 24V ILOAD = 200µA FIGURE 8 CIRCUIT 3786 G07 VIN = 12V 20ms/DIV VOUT = 24V FIGURE 8 CIRCUIT 3786 G08 3786fa 5 LTC3786 Typical Performance Characteristics Regulated Feedback Voltage vs Temperature Soft-Start Pull-Up Current vs Temperature 1.203 1.200 1.197 1.194 10.0 SHUTDOWN CURRENT (µA) 1.206 10.5 10.0 9.5 9.5 9.0 8.5 8.0 7.5 7.0 6.5 6.0 1.191 5.5 1.188 –45 –20 80 55 30 TEMPERATURE (°C) 5 105 9.0 –45 130 5 105 80 5 10 15 20 25 30 INPUT VOLTAGE (V) 35 130 3786 G11 1.35 60 50 40 RUN RISING 1.30 1.25 1.20 RUN FALLING 1.15 20 –45 –20 40 105 1.40 30 5 80 5 55 30 TEMPERATURE (°C) Shutdown (RUN) Threshold vs Temperature RUN PIN VOLTAGE (V) QUIESCENT CURRENT (µA) 10 –20 3786 G10 VIN = 12V VFB = 1.25V 70 15 0 5.0 –45 130 Quiescent Current vs Temperature 20 SHUTDOWN CURRENT (µA) 80 55 30 TEMPERATURE (°C) –20 3786 G09 Shutdown Current vs Input Voltage 0 VIN = 12V 10.5 1.209 SOFT-START CURRENT (µA) REGULATED FEEDBACK VOLTAGE (V) Shutdown Current vs Temperature 11.0 11.0 1.212 55 30 80 5 TEMPERATURE (°C) 3786 G12 105 1.10 –45 –20 130 80 55 30 TEMPERATURE (°C) 5 105 130 3786 G14 3786 G13 Undervoltage Lockout Threshold vs Temperature 4.4 5.5 4.3 5.4 INTVCC RISING INTVCC FALLING 3.8 NO LOAD 5.4 3.7 5.1 5.0 4.9 4.8 5.2 5.1 5.0 4.9 4.8 3.6 4.7 3.5 4.6 4.6 3.4 –45 4.5 4.5 –20 80 5 55 30 TEMPERATURE (°C) 105 130 3786 G15 NO LOAD 5.3 5.2 INTVCC VOLTAGE (V) 4.0 3.9 INTVCC Line Regulation 5.5 5.3 4.1 INTVCC VOLTAGE (V) INTVCC VOLTAGE (V) 4.2 INTVCC Line Regulation 4.7 0 5 10 15 20 25 30 INPUT VOLTAGE (V) 35 40 3786 G16 4.5 4.75 5.25 5.5 5.0 INPUT VOLTAGE (V) 5.75 6.0 3786 G17 3786fa 6 LTC3786 Typical Performance Characteristics INTVCC vs Load Current 5.2 VIN = 12V 5.40 INTVCC VOLTAGE (V) 5.35 5.30 5.25 550 4.8 500 4.6 4.4 0 20 40 4.0 60 80 100 120 140 160 180 LOAD CURRENT (mA) 0 10 20 30 40 LOAD CURRENT (mA) Oscillator Frequency vs Input Voltage 356 354 352 350 348 346 344 342 340 5 10 25 30 20 15 INPUT VOLTAGE (V) 35 40 120 80 60 40 20 0 –20 –40 –60 SENSE CURRENT (µA) SENSE CURRENT (µA) SENSE+ PIN 0.5 2 1.5 1 ITH VOLTAGE (V) 2.5 3 3786 G24 55 5 30 80 TEMPERATURE (°C) 0.2 0.4 0.6 0.8 1.0 ITH VOLTAGE (V) 1.2 1.4 3786 G22 260 VSENSE = 12V 240 220 SENSE+ PIN 200 180 160 140 120 100 80 60 40 20 SENSE – PIN 0 55 30 –45 –20 5 80 TEMPERATURE (°C) SENSE Pin Input Current vs VSENSE Voltage VSENSE = 12V 0 0 3786 G21 SENSE – PIN –20 105 130 3786 G20 SENSE Pin Input Current vs Temperature PULSE-SKIPPING MODE FORCED CONTINUOUS MODE Burst Mode OPERATION 100 SENSE Pin Input Current vs ITH Voltage 260 240 220 200 180 160 140 120 100 80 60 40 20 0 FREQ = GND 300 –45 60 SENSE CURRENT (µA) MAXIMUM CURRENT SENSE VOLTAGE (mV) OSCILLATOR FREQUENCY (kHz) 358 50 Maximum Current Sense Threshold vs ITH Voltage FREQ = GND 400 3786 G19 3786 G18 360 450 350 4.2 5.20 5.15 FREQ = INTVCC 5.0 260 240 220 200 180 160 140 120 100 80 60 40 20 0 SENSE+ PIN SENSE – PIN 2.5 105 130 3786 G23 Maximum Current Sense Threshold vs Duty Cycle MAXIMUM CURRENT SENSE VOLTAGE (mV) INTVCC VOLTAGE (V) 5.45 600 VIN = 5V FREQUENCY (kHz) 5.50 Oscillator Frequency vs Temperature INTVCC vs Load Current 7.5 12.5 17.5 22.5 27.5 32.5 37.5 VSENSE COMMON MODE VOLTAGE (V) 3786 G25 120 100 80 60 40 20 0 0 10 20 30 40 50 60 70 80 90 100 DUTY CYCLE (%) 3786 G26 3786fa 7 LTC3786 Typical Performance Characteristics Charge Pump Charging Current vs Operating Frequency Charge Pump Charging Current vs Switch Voltage VBOOST = 16.5V 100 VSW = 12V 90 120 –45°C 25°C 80 70 130°C 60 50 40 30 20 10 0 50 150 250 350 450 550 650 750 OPERATING FREQUENCY (kHz) 3786 G27 Pin Functions CHARGE PUMP CHARGING CURRENT (µA) CHARGE PUMP CHARGING CURRENT (µA) 110 FREQ = 0V 100 FREQ = INTVCC 80 60 40 20 0 5 10 25 20 30 15 SWITCH VOLTAGE (V) 35 40 3786 G28 (MSOP/QFN) VFB (Pin 1/Pin 3): Error Amplifier Feedback Input. This pin receives the remotely sensed feedback voltage from an external resistive divider connected across the output. SS (Pin 5/Pin 7): Output Soft-Start Input. A capacitor to ground at this pin sets the ramp rate of the output voltage during start-up. SENSE+ (Pin 2/Pin 4): Positive Current Sense Comparator Input. The (+) input to the current comparator is normally connected to the positive terminal of a current sense resistor. The current sense resistor is normally placed at the input of the boost controller in series with the inductor. This pin also supplies power to the current comparator. PLLIN/MODE (Pin 6/Pin 9): External Synchronization Input to Phase Detector and Forced Continuous Mode Input. When an external clock is applied to this pin, it will force the controller into forced continuous mode of operation and the phase-locked loop will force the rising BG signal to be synchronized with the rising edge of the external clock. When not synchronizing to an external clock, this input determines how the LTC3786 operates at light loads. Pulling this pin to ground selects Burst Mode operation. An internal 100k resistor to ground also invokes Burst Mode operation when the pin is floated. Tying this pin to INTVCC forces continuous inductor current operation. Tying this pin to a voltage greater than 1.2V and less than INTVCC – 1.3V selects pulse-skipping operation. This can be done by adding a 100k resistor between the PLLIN/ MODE pin and INTVCC. SENSE– (Pin 3/Pin 5): Negative Current Sense Comparator Input. The (–) input to the current comparator is normally connected to the negative terminal of a current sense resistor connected in series with the inductor. The common mode voltage range on the SENSE+ and SENSE– pins is 2.5V to 38V (40V abs max). ITH (Pin 4/Pin 6): Current Control Threshold and Error Amplifier Compensation Point. The voltage on this pin sets the current trip threshold. 3786fa 8 LTC3786 Pin Functions (MSOP/QFN) FREQ (Pin 7/Pin 9): The Frequency Control Pin for the Internal VCO. Connecting the pin to GND forces the VCO to a fixed low frequency of 350kHz. Connecting the pin to INTVCC forces the VCO to a fixed high frequency of 535kHz. The frequency can be programmed from 50kHz to 900kHz by connecting a resistor from the FREQ pin to GND. The resistor and an internal 20µA source current create a voltage used by the internal oscillator to set the frequency. Alternatively, this pin can be driven with a DC voltage to vary the frequency of the internal oscillator. RUN (Pin 8/Pin 10): Run Control Input. Forcing this pin below 1.28V shuts down the controller. Forcing this pin below 0.7V shuts down the entire LTC3786, reducing quiescent current to approximately 8µA. An external resistor divider connected to VIN can set the threshold for converter operation. Once running, a 4.5µA current is sourced from the RUN pin allowing the user to program hysteresis using the resistor values. GND (Pin 9, Exposed Pad Pin 17/ Pin 11, Exposed Pad Pin 17): Ground. Connects to the source of the bottom (main) N-channel MOSFET and the (–) terminal(s) of CIN and COUT . All small-signal components and compensation components should also connect to this ground. The exposed pad must be soldered to the PCB for rated thermal performance. BG (Pin 10/Pin 12): Bottom Gate. Connect to the gate of the main N-channel MOSFET. INTVCC (Pin 11/Pin 13): Output of Internal 5.4V LDO. Power supply for control circuits and gate drivers. Decouple this pin to GND with a minimum 4.7µF low ESR ceramic capacitor. VBIAS (Pin 12/Pin 14): Main Supply Pin. It is normally tied to the input supply VIN or to the output of the boost converter. A bypass capacitor should be tied between this pin and the GND pin. The operating voltage range on this pin is 4.5V to 38V (40V abs max). BOOST (Pin 13/Pin 15): Floating Power Supply for the Synchronous MOSFET. Bypass to SW with a capacitor and supply with a Schottky diode connected to INTVCC. TG (Pin 14/Pin 16): Top Gate. Connect to the gate of the synchronous NMOS. SW (Pin 15/Pin 1): Switch Node. Connect to the source of the synchronous top MOSFET, the drain of the main bottom MOSFET, and the inductor. PGOOD (Pin 16/Pin 2): Power Good Indicator. Open-drain logic output that is pulled to ground when the output voltage is more than ±10 % away from the regulated output voltage. To avoid false trips the output voltage must be outside of the range for 25µs before this output is activated. 3786fa 9 LTC3786 Block Diagram INTVCC 1.32V VFB 1.08V S R Q CB TG SHDN + – SWITCHING LOGIC AND CHARGE PUMP 20µA VCO CLK + – 0.425V ICMP –+ SLEEP +– + IREV – L 2mV SENSE – SENSE+ SLOPE COMP SYNC DET 100k SENS LO + – 2.5V 0.5µA/ 4.5µA CIN VFB + – 1.2V SS + – 1.32V EA – OV SHDN RSENSE VIN VBIAS ITH CC CC2 – + 11V 10µA SHDN GND RUN RC 3786 BD 3.8V INTVCC COUT INTVCC 2.8V 0.7V 5.4V LDO VOUT SW BG PFD PLLIN/ MODE DB BOOST + – FREQ PGOOD + – SENS LO SS CSS 3786fa 10 LTC3786 Operation (Refer to the Block Diagram) Main Control Loop The LTC3786 uses a constant-frequency, current mode step-up control architecture. During normal operation, the external bottom MOSFET is turned on when the clock sets the RS latch, and is turned off when the main current comparator, ICMP , resets the RS latch. The peak inductor current at which ICMP trips and resets the latch is controlled by the voltage on the ITH pin, which is the output of the error amplifier, EA. The error amplifier compares the output voltage feedback signal at the VFB pin, (which is generated with an external resistor divider connected across the output voltage, VOUT , to ground) to the internal 1.200V reference voltage. In a boost converter, the required inductor current is determined by the load current, VIN and VOUT . When the load current increases, it causes a slight decrease in VFB relative to the reference, which causes the EA to increase the ITH voltage until the average inductor current in each channel matches the new requirement based on the new load current. After the bottom MOSFET is turned off each cycle, the top MOSFET is turned on until either the inductor current starts to reverse, as indicated by the current comparator IR, or the beginning of the next clock cycle. INTVCC Power Power for the top and bottom MOSFET drivers and most other internal circuitry is derived from the INTVCC pin. The VBIAS LDO (low dropout linear regulator) supplies 5.4V from VBIAS to INTVCC. Shutdown and Start-Up (RUN and SS Pins) The LTC3786 can be shut down using the RUN pin. Pulling this pin below 1.28V shuts down the main control loop. Pulling this pin below 0.7V disables the controller and most internal circuits, including the INTVCC LDOs. In this state, the LTC3786 draws only 8µA of quiescent current. Note: Do not apply load while the chip is in shutdown. The output MOSFET will be turned off during shutdown and the output load may cause excessive power dissipation in the body diode. The RUN pin may be externally pulled up or driven directly by logic. When driving the RUN pin with a low imped- ance source, do not exceed the absolute maximum rating of 8V. The RUN pin has an internal 11V voltage clamp that allows the RUN pin to be connected through a resistor to a higher voltage (for example, VIN), as long as the maximum current into the RUN pin does not exceed 100µA. An external resistor divider connected to VIN can set the threshold for converter operation. Once running, a 4.5µA current is sourced from the RUN pin allowing the user to program hysteresis using the resistor values. The start-up of the controller’s output voltage, VOUT , is controlled by the voltage on the SS pin. When the voltage on the SS pin is less than the 1.2V internal reference, the LTC3786 regulates the VFB voltage to the SS pin voltage instead of the 1.2V reference. This allows the SS pin to be used to program a soft-start by connecting an external capacitor from the SS pin to GND. An internal 10µA pullup current charges this capacitor creating a voltage ramp on the SS pin. As the SS voltage rises linearly from 0V to 1.2V, the output voltage rises smoothly to its final value. Light Load Current Operation—Burst Mode Operation, Pulse-Skipping or Continuous Conduction (PLLIN/MODE Pin) The LTC3786 can be enabled to enter high efficiency Burst Mode operation, constant-frequency pulse-skipping mode or forced continuous conduction mode at low load currents. To select Burst Mode operation, tie the PLLIN/MODE pin to ground. To select forced continuous operation, tie the PLLIN/MODE pin to INTVCC. To select pulse-skipping mode, tie the PLLIN/MODE pin to a DC voltage greater than 1.2V and less than INTVCC – 1.3V. When the controller is enabled for Burst Mode operation, the minimum peak current in the inductor is set to approximately 30% of the maximum sense voltage even though the voltage on the ITH pin indicates a lower value. If the average inductor current is higher than the required current, the error amplifier, EA, will decrease the voltage on the ITH pin. When the ITH voltage drops below 0.425V, the internal sleep signal goes high (enabling sleep mode) and both external MOSFETs are turned off. The ITH pin is then disconnected from the output of the EA and parked at 0.450V. 3786fa 11 LTC3786 Operation (Refer to the Block Diagram) In sleep mode, much of the internal circuitry is turned off and the LTC3786 draws only 55µA of quiescent current. In sleep mode, the load current is supplied by the output capacitor. As the output voltage decreases, the EA’s output begins to rise. When the output voltage drops enough, the ITH pin is reconnected to the output of the EA, the sleep signal goes low, and the controller resumes normal operation by turning on the bottom external MOSFET on the next cycle of the internal oscillator. When the controller is enabled for Burst Mode operation, the inductor current is not allowed to reverse. The reversecurrent comparator (IR) turns off the top external MOSFET just before the inductor current reaches zero, preventing it from reversing and going negative. Thus, the controller operates in discontinuous current operation. In forced continuous operation or when clocked by an external clock source to use the phase-locked loop (see the Frequency Selection and Phase-Locked Loop section), the inductor current is allowed to reverse at light loads or under large transient conditions. The peak inductor current is determined by the voltage on the ITH pin, just as in normal operation. In this mode, the efficiency at light loads is lower than in Burst Mode operation. However, continuous operation has the advantages of lower output voltage ripple and less interference to audio circuitry, as it maintains constant-frequency operation independent of load current. When the PLLIN/MODE pin is connected for pulse-skipping mode, the LTC3786 operates in PWM pulse-skipping mode at light loads. In this mode, constant-frequency operation is maintained down to approximately 1% of designed maximum output current. At very light loads, the current comparator ICMP may remain tripped for several cycles and force the external bottom MOSFET to stay off for the same number of cycles (i.e., skipping pulses). The inductor current is not allowed to reverse (discontinuous operation). This mode, like forced continuous operation, exhibits low output ripple as well as low audio noise and reduced RF interference as compared to Burst Mode operation. It provides higher low current efficiency than forced continuous mode, but not nearly as high as Burst Mode operation. Frequency Selection and Phase-Locked Loop (FREQ and PLLIN/MODE Pins) The selection of switching frequency is a trade-off between efficiency and component size. Low frequency operation increases efficiency by reducing MOSFET switching losses, but requires larger inductance and/or capacitance to maintain low output ripple voltage. The switching frequency of the LTC3786’s controllers can be selected using the FREQ pin. If the PLLIN/MODE pin is not being driven by an external clock source, the FREQ pin can be tied to GND, tied to INTVCC, or programmed through an external resistor. Tying FREQ to GND selects 350kHz while tying FREQ to INTVCC selects 535kHz. Placing a resistor between FREQ and GND allows the frequency to be programmed between 50kHz and 900kHz, as shown in Figure 5. A phase-locked loop (PLL) is available on the LTC3786 to synchronize the internal oscillator to an external clock source that is connected to the PLLIN/MODE pin. The LTC3786’s phase detector adjusts the voltage (through an internal lowpass filter) of the VCO input to align the turn-on of the external bottom MOSFET to the rising edge of the synchronizing signal. The VCO input voltage is prebiased to the operating frequency set by the FREQ pin before the external clock is applied. If prebiased near the external clock frequency, the PLL loop only needs to make slight changes to the VCO input in order to synchronize the rising edge of the external clock’s to the rising edge of BG. The ability to prebias the loop filter allows the PLL to lock-in rapidly without deviating far from the desired frequency. 3786fa 12 LTC3786 Operation (Refer to the Block Diagram) The typical capture range of the LTC3786’s PLL is from approximately 55kHz to 1MHz, and is guaranteed to lock to an external clock source whose frequency is between 75kHz and 850kHz. The typical input clock thresholds on the PLLIN/MODE pin are 1.6V (rising) and 1.2V (falling). Operation When VIN > Regulated VOUT When VIN rises above the regulated VOUT voltage, the boost controller can behave differently depending on the mode, inductor current and VIN voltage. In forced continuous mode, the loop keeps the top MOSFET on continuously once VIN rises above VOUT . The internal charge pump delivers current to the boost capacitor to maintain a sufficiently high TG voltage. (The amount of current the charge pump can deliver is characterized by two curves in the Typical Performance Characteristics section.) In pulse-skipping mode, if VIN is between 100% and 110% of the regulated VOUT voltage, TG turns on if the inductor current rises above a certain threshold and turns off if the inductor current falls below this threshold. This threshold current is set to approximately 4% of the maximum ILIM current. If the controller is programmed to Burst Mode operation under this same VIN window, then TG remains off regardless of the inductor current. If VIN rises above 110% of the regulated VOUT voltage in any mode, the controller turns on TG regardless of the inductor current. In Burst Mode operation, however, the internal charge pump turns off if the chip is asleep. With the charge pump off, there would be nothing to prevent the boost capacitor from discharging, resulting in an insufficient TG voltage needed to keep the top MOSFET completely on. To prevent excessive power dissipation across the body diode of the top MOSFET in this situation, the chip can be switched over to forced continuous or pulse-skipping mode to enable the charge pump, or a Schottky diode can also be placed in parallel to the top MOSFET. Power Good The PGOOD pin is connected to an open-drain of an internal N-channel MOSFET. The MOSFET turns on and pulls the PGOOD pin low when the VFB pin voltage is not within ±10% of the 1.2V reference voltage. The PGOOD pin is also pulled low when the corresponding RUN pin is low (shut down). When the VFB pin voltage is within the ±10% requirement, the MOSFET is turned off and the pin is allowed to be pulled up by an external resistor to a source of up to 6V (abs max). Operation at Low SENSE Pin Common Mode Voltage The current comparator in the LTC3786 is powered directly from the SENSE+ pin. This enables the common mode voltage of SENSE+ and SENSE– pins to operate as low as 2.5V, which is below the INTVCC UVLO threshold. The figure on the first page shows a typical application when the controller’s VBIAS is powered from VOUT while VIN supply can go as low as 2.5V. If the voltage on SENSE+ drops below 2.5V, the SS pin will be held low. When the SENSE+ voltage returns to the normal operating range, the SS pin will be released, initiating a new soft-start cycle. BOOST Supply Refresh and Internal Charge Pump The top MOSFET driver is biased from the floating bootstrap capacitor, CB, which normally recharges during each cycle through an external diode when the bottom MOSFET turns on. There are two considerations to keep the BOOST supply at the required bias level. During start-up, if the bottom MOSFET is not turned on within 100µs after UVLO goes low, the bottom MOSFET will be forced to turn on for ~400ns. This forced refresh generates enough BOOSTSW voltage to allow the top MOSFET to be fully enhanced instead of waiting for the initial few cycles to charge the bootstrap capacitor, CB. There is also an internal charge pump that keeps the required bias on BOOST. The charge pump always operates in both forced continuous mode and pulse-skipping mode. In Burst Mode operation, the charge pump is turned off during sleep and enabled when the chip wakes up. The internal charge pump can normally supply a charging current of 85µA. 3786fa 13 LTC3786 Applications Information The Typical Application on the first page is a basic LTC3786 application circuit. LTC3786 can be configured to use either inductor DCR (DC resistance) sensing or a discrete sense resistor (RSENSE) for current sensing. The choice between the two current sensing schemes is largely a design tradeoff between cost, power consumption and accuracy. DCR sensing is becoming popular because it does not require current sensing resistors and is more power efficient, especially in high current applications. However, current sensing resistors provide the most accurate current limits for the controller. Other external component selection is driven by the load requirement, and begins with the selection of RSENSE (if RSENSE is used) and inductor value. Next, the power MOSFETs are selected. Finally, input and output capacitors are selected. SENSE+ and SENSE– Pins The SENSE+ and SENSE– pins are the inputs to the current comparators. The common mode input voltage range of the current comparators is 2.5V to 38V. The current sense resistor is normally placed at the input of the boost controller in series with the inductor. The SENSE+ pin also provides power to the current comparator. It draws ~200µA during normal operation. There is a small base current of less than 1µA that flows into the SENSE– pin. The high impedance SENSE– input to the current comparators allows accurate DCR sensing. VIN VBIAS SENSE+ Filter components mutual to the sense lines should be placed close to the LTC3786, and the sense lines should run close together to a Kelvin connection underneath the current sense element (shown in Figure 1). Sensing current elsewhere can effectively add parasitic inductance and capacitance to the current sense element, degrading the information at the sense terminals and making the programmed current limit unpredictable. If DCR sensing is used (Figure 2b), sense resistor R1 should be placed close to the switching node, to prevent noise from coupling into sensitive small-signal nodes. Sense Resistor Current Sensing A typical sensing circuit using a discrete resistor is shown in Figure 2a. RSENSE is chosen based on the required output current. The current comparator has a maximum threshold VSENSE(MAX) of 75mV. The current comparator threshold sets the peak of the inductor current, yielding a maximum average inductor current, IMAX, equal to the peak value TO SENSE FILTER, NEXT TO THE CONTROLLER VIN INDUCTOR OR RSENSE 3786 F01 Figure 1. Sense Lines Placement with Inductor or Sense Resistor VIN VBIAS SENSE+ C1 (OPTIONAL) SENSE– R2 DCR SENSE– INTVCC INTVCC LTC3786 LTC3786 BOOST BOOST TG TG VOUT SW R1 SW BG BG SGND SGND 3786 F02a INDUCTOR VOUT 3786 F02b L PLACE C1 NEAR SENSE PINS (R1||R2) • C1 = DCR (2a) Using a Resistor to Sense Current L RSENSE(EQ) = DCR • R2 R1 + R2 (2b) Using the Inductor DCR to Sense Current Figure 2. Two Different Methods of Sensing Current 3786fa 14 LTC3786 Applications Information less half the peak-to-peak ripple current, ∆IL. To calculate the sense resistor value, use the equation: R SENSE = VSENSE(MAX) I MAX + ∆IL 2 When using the controller in low VIN and very high voltage output applications, the maximum inductor current and correspondingly the maximum output current level will be reduced due to the internal compensation required to meet stability criterion for boost regulators operating at greater than 50% duty factor. A curve is provided in the Typical Performance Characteristics section to estimate this reduction in peak inductor current level depending upon the operating duty factor. Inductor DCR Sensing For applications requiring the highest possible efficiency at high load currents, the LTC3786 is capable of sensing the voltage drop across the inductor DCR, as shown in Figure 2b. The DCR of the inductor can be less than 1mΩ for high current inductors. In a high current application requiring such an inductor, conduction loss through a sense resistor could reduce the efficiency by a few percent compared to DCR sensing. If the external R1||R2 • C1 time constant is chosen to be exactly equal to the L/DCR time constant, the voltage drop across the external capacitor is equal to the drop across the inductor DCR multiplied by R2/(R1 + R2). R2 scales the voltage across the sense terminals for applications where the DCR is greater than the target sense resistor value. To properly dimension the external filter components, the DCR of the inductor must be known. It can be measured using a good RLC meter, but the DCR tolerance is not always the same and varies with temperature. Consult the manufacturer’s data sheets for detailed information. Using the inductor ripple current value from the inductor value calculation section, the target sense resistor value is: RSENSE(EQUIV) = VSENSE(MAX) ∆IL IMAX + 2 To ensure that the application will deliver full load current over the full operating temperature range, choose the minimum value for the maximum current sense threshold (VSENSE(MAX)). Next, determine the DCR of the inductor. Where provided, use the manufacturer’s maximum value, usually given at 20°C. Increase this value to account for the temperature coefficient of resistance, which is approximately 0.4%/°C. A conservative value for the maximum inductor temperature (TL(MAX)) is 100°C. To scale the maximum inductor DCR to the desired sense resistor value, use the divider ratio: RD = RSENSE(EQUIV) DCRMAX at TL(MAX) C1 is usually selected to be in the range of 0.1µF to 0.47µF. This forces R1|| R2 to around 2k, reducing error that might have been caused by the SENSE– pin’s ±1µA current. The equivalent resistance R1|| R2 is scaled to the room temperature inductance and maximum DCR: R1|| R2 = L (DCR at 20°C) • C1 The sense resistor values are: R1= R1|| R2 R1• RD ; R2 = RD 1– RD The maximum power loss in R1 is related to duty cycle, and will occur in continuous mode at VIN = 1/2 VOUT : PLOSS _ R1 = ( VOUT • VIN ) • VIN R1 Ensure that R1 has a power rating higher than this value. If high efficiency is necessary at light loads, consider this power loss when deciding whether to use DCR sensing or sense resistors. Light load power loss can be modestly higher with a DCR network than with a sense resistor, due to the extra switching losses incurred through R1. However, DCR sensing eliminates a sense resistor, reduces conduction losses and provides higher efficiency at heavy loads. Peak efficiency is about the same with either method. 3786fa 15 LTC3786 Applications Information Inductor Value Calculation The operating frequency and inductor selection are interrelated in that higher operating frequencies allow the use of smaller inductor and capacitor values. Why would anyone ever choose to operate at lower frequencies with larger components? The answer is efficiency. A higher frequency generally results in lower efficiency because of MOSFET gate charge and switching losses. Also, at higher frequency, the duty cycle of body diode conduction is higher, which results in lower efficiency. In addition to this basic trade-off, the effect of inductor value on ripple current and low current operation must also be considered. The inductor value has a direct effect on ripple current. The inductor ripple current ∆IL decreases with higher inductance or frequency and increases with higher VIN: ∆IL = VIN V 1– IN f • L VOUT Accepting larger values of ∆IL allows the use of low inductances, but results in higher output voltage ripple and greater core losses. A reasonable starting point for setting ripple current is ∆IL = 0.3(IMAX). The maximum ∆IL occurs at VIN = 1/2 VOUT . The inductor value also has secondary effects. The transition to Burst Mode operation begins when the average inductor current required results in a peak current below 25% of the current limit determined by RSENSE. Lower inductor values (higher ∆IL) will cause this to occur at lower load currents, which can cause a dip in efficiency in the upper range of low current operation. In Burst Mode operation, lower inductance values will cause the burst frequency to decrease. Once the value of L is known, an inductor with low DCR and low core losses should be selected. Power MOSFET Selection Two external power MOSFETs must be selected for the LTC3786: one N-channel MOSFET for the bottom (main) switch, and one N-channel MOSFET for the top (synchronous) switch. The peak-to-peak gate drive levels are set by the INTVCC voltage. This voltage is typically 5.4V. Consequently, logiclevel threshold MOSFETs must be used in most applications. Pay close attention to the BVDSS specification for the MOSFETs as well; many of the logic level MOSFETs are limited to 30V or less. Selection criteria for the power MOSFETs include the onresistance, RDS(ON), Miller capacitance, CMILLER, input voltage and maximum output current. Miller capacitance, CMILLER, can be approximated from the gate charge curve usually provided on the MOSFET manufacturer’s data sheet. CMILLER is equal to the increase in gate charge along the horizontal axis while the curve is approximately flat divided by the specified change in VDS. This result is then multiplied by the ratio of the application applied VDS to the gate charge curve specified VDS. When the IC is operating in continuous mode, the duty cycles for the top and bottom MOSFETs are given by: Main Switch Duty Cycle = VOUT – VIN VOUT Synchronous Switch Duty Cycle = VIN VOUT If the maximum output current is IOUT(MAX) and each channel takes one-half of the total output current, the MOSFET power dissipations in each channel at maximum output current are given by: PMAIN = ( VOUT – VIN ) VOUT VIN2 • IOUT(MAX)2 • (1+ δ) •RDS(ON) + k • VOUT 3 • IOUT(MAX) VIN • RDR • CMILLER • f PSYNC = VIN • IOUT(MAX)2 • (1+ δ) • RDS(ON) VOUT where δ is the temperature dependency of RDS(ON) (approximately 1Ω) is the effective driver resistance at the MOSFET’s Miller threshold voltage. The constant k, which 3786fa 16 LTC3786 Applications Information accounts for the loss caused by reverse recovery current, is inversely proportional to the gate drive current and has an empirical value of 1.7. Both MOSFETs have I2R losses while the bottom N-channel equation includes an additional term for transition losses, which are highest at low input voltages. For high VIN the high current efficiency generally improves with larger MOSFETs, while for low VIN the transition losses rapidly increase to the point that the use of a higher RDS(ON) device with lower CMILLER actually provides higher efficiency. The synchronous MOSFET losses are greatest at high input voltage when the bottom switch duty factor is low or during overvoltage when the synchronous switch is on close to 100% of the period. The term (1 + δ) is generally given for a MOSFET in the form of a normalized RDS(ON) vs Temperature curve, but δ = 0.005/°C can be used as an approximation for low voltage MOSFETs. CIN and COUT Selection The input ripple current in a boost converter is relatively low (compared with the output ripple current), because this current is continuous. The input capacitor, CIN, voltage rating should comfortably exceed the maximum input voltage. Although ceramic capacitors can be relatively tolerant of overvoltage conditions, aluminum electrolytic capacitors are not. Be sure to characterize the input voltage for any possible overvoltage transients that could apply excess stress to the input capacitors. The value of the CIN is a function of the source impedance, and in general, the higher the source impedance, the higher the required input capacitance. The required amount of input capacitance is also greatly affected by the duty cycle. High output current applications that also experience high duty cycles can place great demands on the input supply, both in terms of DC current and ripple current. In a boost converter, the output has a discontinuous current, so COUT must be capable of reducing the output voltage ripple. The effects of ESR (equivalent series resistance) and the bulk capacitance must be considered when choosing the right capacitor for a given output ripple voltage. The steady ripple voltage due to charging and discharging the bulk capacitance in a single phase boost converter is given by: VRIPPLE = ( IOUT(MAX) • VOUT – VIN(MIN) COUT • VOUT • f )V where COUT is the output filter capacitor. The steady ripple due to the voltage drop across the ESR is given by: ∆VESR = IL(MAX) • ESR Multiple capacitors placed in parallel may be needed to meet the ESR and RMS current handling requirements. Dry tantalum, special polymer, aluminum electrolytic and ceramic capacitors are all available in surface mount packages. Ceramic capacitors have excellent low ESR characteristics but can have a high voltage coefficient. Capacitors are now available with low ESR and high ripple current ratings (i.e., OS-CON and POSCAP). Setting Output Voltage The LTC3786 output voltage is set by an external feedback resistor divider carefully placed across the output, as shown in Figure 3. The regulated output voltage is determined by: R VOUT = 1.2V 1+ B RA Great care should be taken to route the VFB line away from noise sources, such as the inductor or the SW line. Also, keep the VFB node as small as possible to avoid noise pickup. VOUT LTC3786 RB VFB RA 3786 F03 Figure 3. Setting Output Voltage 3786fa 17 LTC3786 Applications Information Soft-Start (SS Pin) The start-up of the VOUT is controlled by the voltage on the SS pin. When the voltage on the SS pin is less than the internal 1.2V reference, the LTC3786 regulates the VFB pin voltage to the voltage on the SS pin instead of 1.2V. Soft-start is enabled by simply connecting a capacitor from the SS pin to ground, as shown in Figure 4. An internal 10µA current source charges the capacitor, providing a linear ramping voltage at the SS pin. The LTC3786 will regulate the VFB pin (and hence, VOUT) according to the voltage on the SS pin, allowing VOUT to rise smoothly from VIN to its final regulated value. The total soft-start time will be approximately: tSS = CSS • 1.2V 10µA LTC3786 SS CSS SGND 3786 F04 Figure 4. Using the SS Pin to Program Soft-Start INTVCC Regulator The LTC3786 features an internal P-channel low dropout linear regulator (LDO) that supplies power at the INTVCC pin from the VBIAS supply pin. INTVCC powers the gate drivers and much of the LTC3786’s internal circuitry. The VBIAS LDO regulates INTVCC to 5.4V. It can supply at least 50mA and must be bypassed to ground with a minimum of 4.7µF ceramic capacitor. Good bypassing is needed to supply the high transient currents required by the MOSFET gate drivers. High input voltage applications in which large MOSFETs are being driven at high frequencies may cause the maximum junction temperature rating for the LTC3786 to be exceeded. The power dissipation for the IC is equal to VBIAS • IINTVCC. The gate charge current is dependent on operating frequency, as discussed in the Efficiency Considerations section. The junction temperature can be estimated by using the equations given in Note 2 of the Electrical Characteristics. For example, at 70°C ambient temperature, the LTC3786 INTVCC current is limited to less than 20mA in the QFN package from a 40V supply: TJ = 70°C + (20mA)(40V)(68°C/W) = 125°C In an MSOP package, the INTVCC current is limited to less than 34mA from a 40V supply: TJ = 70°C + (34mA)(40V)(40°C/W) = 125°C To prevent the maximum junction temperature from being exceeded, the input supply current must be checked while operating in continuous conduction mode (PLLIN/MODE = INTVCC) at maximum VBIAS. Topside MOSFET Driver Supply (CB, DB) External bootstrap capacitors, CB, connected to the BOOST pin supplies the gate drive voltage for the topside MOSFET. Capacitor CB in the Block Diagram is charged though external diode, DB, from INTVCC when the SW pin is low. When the topside MOSFET is to be turned on, the driver places the CB voltage across the gate-source of the desired MOSFET. This enhances the MOSFET and turns on the topside switch. The switch node voltage, SW, rises to VOUT and the BOOST pin follows. With the topside MOSFET on, the boost voltage is above the output voltage: VBOOST = VOUT + VINTVCC. The value of the boost capacitor, CB, needs to be 100 times that of the total input capacitance of the topside MOSFET(s). The reverse breakdown of the external Schottky diode must be greater than VIN(MAX). The external diode DB can be a Schottky diode or silicon diode, but in either case it should have low leakage and fast recovery. Pay close attention to the reverse leakage at high temperatures where it generally increases substantially. The topside MOSFET driver includes an internal charge pump that delivers current to the bootstrap capacitor from the BOOST pin. This charge current maintains the bias voltage required to keep the top MOSFET on continuously during dropout/overvoltage conditions. The Schottky/ silicon diode selected for the topside driver should have a reverse leakage less than the available output current the charge pump can supply. Curves displaying the available charge pump current under different operating conditions can be found in the Typical Performance Characteristics section. 3786fa 18 LTC3786 Applications Information A leaky diode DB in the boost converter can not only prevent the top MOSFET from fully turning on but it can also completely discharge the bootstrap capacitor CB and create a current path from the input voltage to the BOOST pin to INTVCC. This can cause INTVCC to rise if the diode leakage exceeds the current consumption on INTVCC. This is particularly a concern in Burst Mode operation where the load on INTVCC can be very small. The external Schottky or silicon diode should be carefully chosen such that INTVCC never gets charged up much higher than its normal regulation voltage. ously from the phase detector output, pulling up the VCO input. When the external clock frequency is less than fOSC, current is sunk continuously, pulling down the VCO input. If the external and internal frequencies are the same but exhibit a phase difference, the current sources turn on for an amount of time corresponding to the phase difference. The voltage at the VCO input is adjusted until the phase and frequency of the internal and external oscillators are identical. At the stable operating point, the phase detector output is high impedance and the internal filter capacitor, CLP , holds the voltage at the VCO input. Fault Conditions: Overtemperature Protection Typically, the external clock (on PLLIN/MODE pin) input high threshold is 1.6V, while the input low threshold is 1.2V. At higher temperatures, or in cases where the internal power dissipation causes excessive self heating on-chip (such as an INTVCC short to ground), the overtemperature shutdown circuitry will shut down the LTC3786. When the junction temperature exceeds approximately 170°C, the overtemperature circuitry disables the INTVCC LDO, causing the INTVCC supply to collapse and effectively shut down the entire LTC3786 chip. Once the junction temperature drops back to approximately 155°C, the INTVCC LDO turns back on. Long-term overstress (TJ > 125°C) should be avoided as it can degrade the performance or shorten the life of the part. Since the shutdown may occur at full load, beware that the load current won’t result in high power dissipation in the body diodes of the top MOSFET. In this case, PGOOD output may be used to turn the system load off. Note that the LTC3786 can only be synchronized to an external clock whose frequency is within range of the LTC3786’s internal VCO, which is nominally 55kHz to 1MHz. This is guaranteed to be between 75kHz and 850kHz. Rapid phase locking can be achieved by using the FREQ pin to set a free-running frequency near the desired synchronization frequency. The VCO’s input voltage is prebiased at a frequency corresponding to the frequency set by the FREQ pin. Once prebiased, the PLL only needs to adjust the frequency slightly to achieve phase lock and synchronization. Although it is not required that the free-running frequency be near external clock frequency, doing so will prevent the operating frequency from passing through a large range of frequencies as the PLL locks. 1000 900 Phase-Locked Loop and Frequency Synchronization If the external clock frequency is greater than the internal oscillator’s frequency, fOSC, then current is sourced continu- FREQUENCY (kHz) The LTC3786 has an internal phase-locked loop (PLL) comprised of a phase frequency detector, a lowpass filter and a voltage-controlled oscillator (VCO). This allows the turn-on of the bottom MOSFET to be locked to the rising edge of an external clock signal applied to the PLLIN/MODE pin. The phase detector is an edge-sensitive digital type that provides zero degrees phase shift between the external and internal oscillators. This type of phase detector does not exhibit false lock to harmonics of the external clock. 800 700 600 500 400 300 200 100 0 15 25 35 45 55 65 75 85 95 105 115 125 FREQ PIN RESISTOR (kΩ) 3786 F05 Figure 5. Relationship Between Oscillator Frequency and Resistor Value at the FREQ Pin 3786fa 19 LTC3786 Applications Information Table 2 summarizes the different states in which the FREQ pin can be used. Table 2 FREQ PIN PLLIN/MODE PIN FREQUENCY 0V DC Voltage 350kHz INTVCC DC Voltage 535kHz Resistor DC Voltage 50kHz to 900kHz Any of the Above External Clock Phase Locked to External Clock Minimum On-Time Considerations Minimum on-time, tON(MIN), is the smallest time duration that the LTC3786 is capable of turning on the bottom MOSFET. It is determined by internal timing delays and the gate charge required to turn on the top MOSFET. Low duty cycle applications may approach this minimum on-time limit. In forced continuous mode, if the duty cycle falls below what can be accommodated by the minimum on-time, the controller will begin to skip cycles but the output will continue to be regulated. More cycles will be skipped when VIN increases. Once VIN rises above VOUT , the loop keeps the top MOSFET continuously on. The minimum on-time for the LTC3786 is approximately 110ns. Efficiency Considerations The percent efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting the efficiency and which change would produce the greatest improvement. Percent efficiency can be expressed as: %Efficiency = 100% – (L1 + L2 + L3 + ...) where L1, L2, etc., are the individual losses as a percentage of input power. Although all dissipative elements in the circuit produce losses, five main sources usually account for most of the losses in LTC3786 circuits: 1) IC VBIAS current, 2) INTVCC regulator current, 3) I2R losses, 4) Bottom MOSFET transition losses and 5) Body diode conduction losses. 1. The VBIAS current is the DC supply current given in the Electrical Characteristics table, which excludes MOSFET driver and control currents. VBIAS current typically results in a small (<0.1%) loss. 2. INTVCC current is the sum of the MOSFET driver and control currents. The MOSFET driver current results from switching the gate capacitance of the power MOSFETs. Each time a MOSFET gate is switched from low to high to low again, a packet of charge, dQ, moves from INTVCC to ground. The resulting dQ/dt is a current out of INTVCC that is typically much larger than the control circuit current. In continuous mode, IGATECHG = f(QT + QB), where QT and QB are the gate charges of the topside and bottom side MOSFETs. 3. DC I2R losses. These arise from the resistances of the MOSFETs, sensing resistor, inductor and PC board traces and cause the efficiency to drop at high output currents. 4. Transition losses apply only to the bottom MOSFET(s), and become significant only when operating at low input voltages. Transition losses can be estimated from: Transition Loss = (1.7) VOUT 3 IMAX • CRSS • f VIN 5. Body diode conduction losses are more significant at higher switching frequency. During the dead time, the loss in the top MOSFETs is IL • VDS, where VDS is around 0.7V. At higher switching frequency, the dead time becomes a good percentage of switching cycle and causes the efficiency to drop. Other hidden losses, such as copper trace and internal battery resistances, can account for an additional efficiency degradation in portable systems. It is very important to include these system-level losses during the design phase. 3786fa 20 LTC3786 Applications Information Checking Transient Response The regulator loop response can be checked by looking at the load current transient response. Switching regulators take several cycles to respond to a step in load current. When a load step occurs, VOUT shifts by an amount equal to ∆ILOAD(ESR), where ESR is the effective series resistance of COUT . ∆ILOAD also begins to charge or discharge COUT generating the feedback error signal that forces the regulator to adapt to the current change and return VOUT to its steady-state value. During this recovery time VOUT can be monitored for excessive overshoot or ringing, which would indicate a stability problem. OPTI‑LOOP® compensation allows the transient response to be optimized over a wide range of output capacitance and ESR values. The availability of the ITH pin not only allows optimization of control loop behavior, but it also provides a DC-coupled and AC-filtered closed-loop response test point. The DC step, rise time and settling at this test point truly reflects the closed-loop response. Assuming a predominantly second order system, phase margin and/or damping factor can be estimated using the percentage of overshoot seen at this pin. The bandwidth can also be estimated by examining the rise time at the pin. The ITH external components shown in the Figure 8 circuit will provide an adequate starting point for most applications. The ITH series RC-CC filter sets the dominant pole-zero loop compensation. The values can be modified slightly to optimize transient response once the final PCB layout is complete and the particular output capacitor type and value have been determined. The output capacitors must be selected because the various types and values determine the loop gain and phase. An output current pulse of 20% to 80% of full-load current having a rise time of 1µs to 10µs will produce output voltage and ITH pin waveforms that will give a sense of the overall loop stability without breaking the feedback loop. Placing a power MOSFET and load resistor directly across the output capacitor and driving the gate with an appropriate pulse generator is a practical way to produce a realistic load step condition. The initial output voltage step resulting from the step change in output current may not be within the bandwidth of the feedback loop, so this signal cannot be used to determine phase margin. This is why it is better to look at the ITH pin signal which is in the feedback loop and is the filtered and compensated control loop response. The gain of the loop will be increased by increasing RC and the bandwidth of the loop will be increased by decreasing CC. If RC is increased by the same factor that CC is decreased, the zero frequency will be kept the same, thereby keeping the phase shift the same in the most critical frequency range of the feedback loop. The output voltage settling behavior is related to the stability of the closed-loop system and will demonstrate the actual overall supply performance. A second, more severe transient is caused by switching in loads with large (>1µF) supply bypass capacitors. The discharged bypass capacitors are effectively put in parallel with COUT , causing a rapid drop in VOUT . No regulator can alter its delivery of current quickly enough to prevent this sudden step change in output voltage if the load switch resistance is low and it is driven quickly. If the ratio of CLOAD to COUT is greater than 1:50, the switch rise time should be controlled so that the load rise time is limited to approximately 25 • CLOAD. Thus, a 10µF capacitor would require a 250µs rise time, limiting the charging current to about 200mA. Design Example As a design example, assume VIN = 12V(nominal), VIN = 22V (max), VOUT = 24V, IOUT(MAX) = 4A, VSENSE(MAX) = 75mV and f = 350kHz. The inductance value is chosen first based on a 30% ripple current assumption. Tie the MODE/PLLIN pin to GND, generating 350kHz operation. The minimum inductance for 30% ripple current is: ∆IL = VIN V 1– IN f • L VOUT The largest ripple happens when VIN = 1/2VOUT = 12V, where the average maximum inductor is IMAX = IOUT(MAX) • (VOUT/VIN) = 8A. A 6.8µH inductor will produce a 31% ripple current. The peak inductor current will be the maximum DC value plus one-half the ripple current, or 9.25A. 3786fa 21 LTC3786 Applications Information The RSENSE resistor value can be calculated by using the maximum current sense voltage specification with some accommodation for tolerances: RSENSE ≤ 75mV = 0.008Ω 9.25A Choosing 1% resistors: RA = 5k and RB = 95.3k yields an output voltage of 24.072V. The power dissipation on the topside MOSFET in each channel can be easily estimated. Choosing a Vishay Si7848BDP MOSFET results in: RDS(ON) = 0.012Ω, CMILLER = 150pF. At maximum input voltage with T(estimated) = 50°C: ( 24V – 12V ) 24V 2 • ( 4A ) 2 (12V ) • 1+ ( 0.005 ) ( 50°C – 25°C ) • 0.008Ω PMAIN = + (1.7 ) ( 24V ) 3 4A 12V (150pF ) ( 350kHz ) = 0.7W COUT is chosen to filter the square current in the output. The maximum output current peak is: RIPPLE% IOUT(PEAK) = IOUT(MAX) • 1+ 2 31% = 4 • 1+ = 4.62A 2 A low ESR (5mΩ) capacitor is suggested. This capacitor will limit output voltage ripple to 23.1mV (assuming ESR dominate ripple). PC Board Layout Checklist When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the IC. These items are also illustrated graphically in the layout diagram of Figure 6. Figure 7 illustrates the current waveforms present in the various branches the synchronous regulator operating in the continuous mode. Check the following in your layout: 1. Put the bottom N-channel MOSFET MBOT and the top N-channel MOSFET MTOP in one compact area with COUT . 2. Are the signal and power grounds kept separate? The combined IC signal ground pin and the ground return of CINTVCC must return to the combined COUT (–) terminals. The path formed by the bottom N-channel MOSFET and the capacitor should have short leads and PC trace lengths. The output capacitor (–) terminals should be connected as close as possible to the (–) source terminal of the bottom MOSFET. 3. Does the LTC3786 VFB pin’s resistive divider connect to the (+) terminal of COUT? The resistive divider must be connected between the (+) terminal of COUT and signal ground and placed close to the VFB pin. The feedback resistor connections should not be along the high current input feeds from the input capacitor(s). 4. Are the SENSE– and SENSE+ leads routed together with minimum PC trace spacing? The filter capacitor between SENSE+ and SENSE– should be as close as possible to the IC. Ensure accurate current sensing with Kelvin connections at the sense resistor. 5. Is the INTVCC decoupling capacitor connected close to the IC, between the INTVCC and the power ground pin? This capacitor carries the MOSFET drivers’ current peaks. An additional 1µF ceramic capacitor placed immediately next to the INTVCC and GND pins can help improve noise performance substantially. 6. Keep the switching node (SW), top gate node (TG) and boost node (BOOST) away from sensitive small-signal nodes. All of these nodes have very large and fast moving signals and, therefore, should be kept on the output side of the LTC3786 and occupy a minimal PC trace area. 7. Use a modified “star ground” technique: a low impedance, large copper area central grounding point on the same side of the PC board as the input and output capacitors with tie-ins for the bottom of the INTVCC decoupling capacitor, the bottom of the voltage feedback resistive divider and the GND pin of the IC. 3786fa 22 LTC3786 Applications Information PC Board Layout Debugging It is helpful to use a DC-50MHz current probe to monitor the current in the inductor while testing the circuit. Monitor the output switching node (SW pin) to synchronize the oscilloscope to the internal oscillator and probe the actual output voltage. Check for proper performance over the operating voltage and current range expected in the application. The frequency of operation should be maintained over the input voltage range down to dropout and until the output load drops below the low current operation threshold— typically 10% of the maximum designed current level in Burst Mode operation. The duty cycle percentage should be maintained from cycle to cycle in a well designed, low noise PCB implementation. Variation in the duty cycle at a subharmonic rate can suggest noise pick-up at the current or voltage sensing inputs or inadequate loop compensation. Overcompensation of the loop can be used to tame a poor PC layout if regulator bandwidth optimization is not required. Reduce VIN from its nominal level to verify operation with high duty cycle. Check the operation of the undervoltage lockout circuit by further lowering VIN while monitoring the outputs to verify operation. Investigate whether any problems exist only at higher output currents or only at higher input voltages. If problems coincide with high input voltages and low output currents, look for capacitive coupling between the BOOST, SW, TG, and possibly BG connections and the sensitive voltage and current pins. The capacitor placed across the current sensing pins needs to be placed immediately adjacent to the pins of the IC. This capacitor helps to minimize the effects of differential noise injection due to high frequency capacitive coupling. An embarrassing problem, which can be missed in an otherwise properly working switching regulator results when the current sensing leads are hooked up backwards. The output voltage under this improper hook-up will still be maintained, but the advantages of current mode control will not be realized. Compensation of the voltage loop will be much more sensitive to component selection. This behavior can be investigated by temporarily shorting out the current sensing resistor—don’t worry, the regulator will still maintain control of the output voltage. 3786fa 23 LTC3786 Applications Information SENSE+ PGOOD SENSE– SW LTC3786 L1 TG M2 BG PLLIN/MODE RSENSE CB BOOST FREQ fIN VPULLUP + M1 RUN VFB VBIAS SS + GND ITH VIN GND INTVCC VOUT 3786 F06 Figure 6. Recommended Printed Circuit Layout Diagram RSENSE VIN L1 VOUT SW RIN COUT CIN RL 3786 F07 BOLD LINES INDICATE HIGH SWITCHING CURRENT. KEEP LINES TO A MINIMUM LENGTH Figure 7. Branch Current Waveforms 3786fa 24 LTC3786 Applications Information VBIAS SENSE+ RSENSE 4mΩ LTC3786 SENSE– CSS 0.1µF CITH 15nF RITH 8.66k L 3.3µH PLLIN/MODE RUN FREQ TG SW SS CB 0.1µF MTOP BOOST MBOT BG ITH COUTA 22µF ×4 + COUTB 220µF VOUT 24V 5A* D CITHA 220pF INTVCC GND RA 12.1k VIN 5V TO 24V CIN 22µF VFB PGOOD RS 232k CINT 4.7µF 100k 3786 F08 CIN, COUTA: TDK C4532X5R1E226M COUTB: SANYO 50CE220LX D: BAS140W L: PULSE PA1494.362NL MBOT, MTOP: RENESAS HAT2169H *WHEN VIN < 8V, MAXIMUM LOAD CURRENT AVAILABLE IS REDUCED. Figure 8. High Efficiency 24V Boost Converter VBIAS SENSE+ RSENSE 4mΩ LTC3786 SENSE– CSS 0.1µF PLLIN/MODE RUN FREQ CITH 15nF RITH 8.66k L 3.3µH TG SW SS ITH CITHA 220pF CB 0.1µF BG MBOT COUTA 6.8µF ×4 + COUTB 220µF VOUT 28V 4A* D INTVCC VFB MTOP BOOST GND RA 12.1k VIN 5V TO 28V CIN 6.8µF ×4 PGOOD CINT 4.7µF 100k RS 261k CIN, COUTA: TDK C4532X7R1H685K COUTB: SANYO 63CE220KX D: BAS140W L: PULSE PA1494.362NL MBOT, MTOP: RENESAS HAT2169H 3786 F09 *WHEN VIN < 8V, MAXIMUM LOAD CURRENT AVAILABLE IS REDUCED. Figure 9. High Efficiency 28V Boost Converter 3786fa 25 LTC3786 Applications Information VBIAS SENSE+ RSENSE 5mΩ LTC3786 SENSE– L 10.2µH PLLIN/MODE RUN FREQ CSS 0.1µF TG SW SS CITH 15nF RITH 8.66k CB 0.1µF COUTA 6.8µF ×4 MTOP BOOST BG ITH MBOT + COUTB 220µF VOUT 36V 3A* D CITHA 220pF INTVCC GND RA 12.1k VIN 5V TO 36V CIN 6.8µF ×4 VFB PGOOD CINT 4.7µF 100k RS 357k 3786 F10 CIN, COUTA: TDK C4532X7R1H685K COUTB: SANYO 63CE220KX D: BAS170W L: PULSE PA2050.103NL MBOT, MTOP: RENESAS RJIC0652DPB *WHEN VIN < 9V, MAXIMUM LOAD CURRENT AVAILABLE IS REDUCED. Figure 10. High Efficiency 36V Boost Converter VBIAS SENSE+ RSENSE 9mΩ LTC3786 SENSE– L 10µH PLLIN/MODE RUN FREQ CSS 0.1µF SS CITH 100nF RITH 13k TG • CIN 22µF VIN 5.8V TO 34V • C 10µF D SW BOOST BG MBOT VOUT 10.5V 1.2A COUT 270µF ITH INTVCC CITHA 10pF GND RA 115k VFB PGOOD CINT 4.7µF 100k RS 887k 3786 F11 CIN: SANYO 50CE220LX COUT: SANYO SVPC270M D: DIODES, INC. B360A-13-F L: COOPER BUSSMANN DRQ125-100 MBOT: BSZ097NO4L Figure 11. 10.5V Nonsynchronous SEPIC Converter 3786fa 26 LTC3786 Applications Information VBIAS SENSE+ RSENSE 5mΩ LTC3786 VIN 4.5V TO 24V START-UP VOLTAGE OPERATES THROUGH TRANSIENTS DOWN TO 2.5V CIN 22µF SENSE– 60.4k fSW = 400kHz L 3.2µH RUN FREQ TG CSS 0.1µF SW CB 0.1µF SS CITH 10nF RITH 4.64k CITHA 100pF BOOST RB 88.7k COUTB 150µF D GND VFB + MBOT BG ITH INTVCC RA 12.1k COUTA 22µF ×3 MTOP VOUT* 10V 5A PLLIN/MODE PGOOD CINT 4.7µF 100k 100k 3786 F12a CIN, COUTA: TDK C4532X5R1E226M COUTB: SANYO 35HVH150M L: SUMIDA CDEP106-3R2-88 MBOT, MTOP: RENESAS HAT2170 D: INFINEON BAS140W *WHEN VIN > 10V, VOUT FOLLOWS VIN. 100 VIN = 12V 98 VIN = 9V EFFICIENCY (%) 96 VIN = 6V 94 92 90 88 86 1 4 2 3 OUTPUT CURRENT (A) 5 6 3786 F12b Figure 12. High Efficiency 10V Boost Converter 3786fa 27 LTC3786 Applications Information CIN 47µF ×2 SENSE+ RSENSE 6mΩ LTC3786 SENSE– L 0.67µH PLLIN/MODE CSS 0.1µF CITH 6.8nF RUN TG FREQ SW CITHA 100pF D1 ITH VBIAS INTVCC GND RA 150k CB 0.1µF BOOST BG SS RITH 5.11k CINT 4.7µF VOUT 5V 4A COUT 47µF ×4 MTOP MBOT D2 Q 100k 1M C2 10µF PGOOD VFB VIN 2.7V TO 4.2V RB 475k CFLY 1µF VOUT VIN LTC1754-5 C+ SHDN C– GND C1 10µF 3786 F13a CIN, COUT: TDK C3225X5R1A476M L: TOKO FDV0840-R67M MBOT, MTOP: INFINEON BSC046N02KS Q: VISHAY SILICONIX Si1499DH D1: INFINEON BAS140W D2: NXP PMEG2005EJ CFLY: MURATA GRM39X5R105K6.3AJ C1, C2: MURATA GRM40X5R106K6.3AJ 98 VIN = 4.2V EFFICIENCY (%) 96 VIN = 3.3V 94 VIN = 2.7V 92 90 88 86 0 1 2 3 OUTPUT CURRENT (A) 4 3786 F13b Figure 13. Low IQ Lithium-Ion to 5V/4A Boost Converter 3786fa 28 LTC3786 Applications Information VBIAS SENSE+ LTC3786 RUN FREQ CSS 0.1µF SENSE– TG SW SS CITH 15nF RITH 8.87k C1 0.1µF RS2 26.1k RS1 1% 53.6k 1% L 10.2µH CB 0.1µF MTOP BOOST CITHA 220pF VFB GND PLLIN/MODE PGOOD + COUTB 220µF D INTVCC RA 12.1k COUTA 22µF ×4 VOUT 24V 4A MBOT BG ITH VIN 5V TO 24V CIN 22µF CINT 4.7µF 100k RB 232k 3786 F14a C1: TDK C1005X7R1C104K CIN, COUTA: TDK C4532X5R1E226M COUTB: SANYO, 50CE220AX L: PULSE PA2050.103NL MBOT, MTOP: RENESAS RJK0305 D: INFINEON BAS140W 100 VIN = 12V 98 EFFICIENCY (%) 96 94 92 90 88 86 0 1 2 3 OUTPUT CURRENT (A) 4 3786 F14b Figure 14. High Efficiency 24V Boost Converter with Inductor DCR Current Sensing 3786fa 29 LTC3786 Applications Information DANGER HIGH VOLTAGE! OPERATION BY HIGH VOLTAGE TRAINED PERSONNEL ONLY VBIAS SENSE+ PLLIN/MODE 25k fSW = 105kHz CSS 0.1µF SENSE– RITH 8.66k RUN FREQ TG GND VFB 1M 1% VIN 5V TO 12V VOUT 350V 10mA 220pF MBOT INTVCC 16.2k 1% COUT 68nF ×2 • 22Ω SW BOOST BG ITH CITHA 100pF CIN 22µF ×2 • SS CITH 22nF RSENSE 15mΩ T D 1:10 10nF LTC3786 PGOOD 1M 1% CINT 4.7µF 100k 1.5M 1% 3786 F15 CIN: TDK C3225X7R1C226M COUT: TDK C3225X7R2J683K D: VISHAY SILICONIX GSD2004S DUAL DIODE CONNECTED IN SERIES MBOT: VISHAY SILICONIX Si7850DP T: TDK DCT15EFD-U44S003 Figure 15. Low IQ High Voltage Flyback Power Supply VBIAS SENSE+ RSENSE 6mΩ LTC3786 SENSE– CSS 0.1µF PLLIN/MODE RUN FREQ CITH 22nF RITH 8.66k ITH CITHA 100pF 12.1k 1% L 10µH TG D SW SS COUTA 10µF BOOST BG GND PGOOD + MBOT INTVCC VFB VIN 5V TO 24V CIN 10µF ×2 COUTB 47µF ×4 VOUT 24V 2A CINT 4.7µF 100k 232k 1% CIN, COUTA: MURATA GRM31CR61E106KA12 COUTB: KEMET T495X476K035AS D: ON SEMI MBRS340T3G L: VISAY SILICONIX IHLP-5050FD-01 10µH MBOT: VISHAY SILICONIX Si4840BDP 3786 F15 Figure 16. Low IQ Nonsynchronous 24V/2A Boost Converter 3786fa 30 LTC3786 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. MSE Package 16-Lead Plastic MSOP, Exposed Die Pad (Reference LTC DWG # 05-08-1667 Rev C) BOTTOM VIEW OF EXPOSED PAD OPTION 2.845 ± 0.102 (.112 ± .004) 5.23 (.206) MIN 2.845 ± 0.102 (.112 ± .004) 0.889 ± 0.127 (.035 ± .005) 8 1 1.651 ± 0.102 (.065 ± .004) 1.651 ± 0.102 3.20 – 3.45 (.065 ± .004) (.126 – .136) 0.305 ± 0.038 (.0120 ± .0015) TYP 16 0.50 (.0197) BSC 4.039 ± 0.102 (.159 ± .004) (NOTE 3) RECOMMENDED SOLDER PAD LAYOUT 0.254 (.010) 0.35 REF 0.12 REF DETAIL “B” CORNER TAIL IS PART OF DETAIL “B” THE LEADFRAME FEATURE. FOR REFERENCE ONLY 9 NO MEASUREMENT PURPOSE 0.280 ± 0.076 (.011 ± .003) REF 16151413121110 9 DETAIL “A” 0° – 6° TYP 3.00 ± 0.102 (.118 ± .004) (NOTE 4) 4.90 ± 0.152 (.193 ± .006) GAUGE PLANE 0.53 ± 0.152 (.021 ± .006) DETAIL “A” 1.10 (.043) MAX 0.18 (.007) SEATING PLANE 0.17 – 0.27 (.007 – .011) TYP 1234567 8 0.50 NOTE: (.0197) 1. DIMENSIONS IN MILLIMETER/(INCH) BSC 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 0.86 (.034) REF 0.1016 ± 0.0508 (.004 ± .002) MSOP (MSE16) 0910 REV C 3786fa 31 LTC3786 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. UD Package 16-Lead Plastic QFN (3mm × 3mm) (Reference LTC DWG # 05-08-1691) 0.70 ±0.05 3.50 ± 0.05 1.45 ± 0.05 2.10 ± 0.05 (4 SIDES) PACKAGE OUTLINE 0.25 ±0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 3.00 ± 0.10 (4 SIDES) BOTTOM VIEW—EXPOSED PAD PIN 1 NOTCH R = 0.20 TYP OR 0.25 × 45° CHAMFER R = 0.115 TYP 0.75 ± 0.05 15 PIN 1 TOP MARK (NOTE 6) 16 0.40 ± 0.10 1 1.45 ± 0.10 (4-SIDES) 2 (UD16) QFN 0904 0.200 REF 0.00 – 0.05 NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE MO-220 VARIATION (WEED-2) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 0.25 ± 0.05 0.50 BSC 3786fa 32 LTC3786 Revision History REV DATE DESCRIPTION A 9/11 Updated the Topside MOSFET Driver Supply (CB, DB) section. PAGE NUMBER 18 Updated Figure 12. 27 3786fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 33 LTC3786 Typical Application High Efficiency 48V Boost Converter VBIAS SENSE+ RSENSE 8mΩ LTC3786 SENSE– CSS 0.1µF PLLIN/MODE RUN FREQ CITH 15nF RITH 8.66k L 16µH TG SW SS ITH CITHA 220pF CB 0.1µF BG MBOT RS 475k COUTA 6.8µF ×4 + VOUT 48V 2A* COUTB 220µF D INTVCC VFB MTOP BOOST GND RA 12.1k VIN 5V TO 38V CIN 6.8µF ×4 PGOOD CINT 4.7µF 100k 3786 TA02 CIN, COUTA: TDK C4532X7R1H685K COUTB: SANYO 63CE220KX D: BAS170W L: PULSE PA2050.163NL MBOT, MTOP: RENESAS RJK0652DPB *WHEN VIN < 13V, MAXIMUM LOAD CURRENT AVAILABLE IS REDUCED. Related Parts PART NUMBER DESCRIPTION COMMENTS LTC3788/LTC3788-1 2-Phase Dual Output Synchronous Step-Up Controllers 4.5V ≤ VIN ≤ 38V, VOUT Up to 60V, 50kHz to 900kHz, 5mm × 5mm QFN-32 and SSOP-28 Packages LTC3787 2-Phase Single Output Synchronous Boost Controller 4.5V ≤ VIN ≤ 38V, VOUT Up to 60V, 50kHz to 900kHz, 5mm × 5mm QFN-28 and SSOP-28 Packages LTC3859 Low IQ, Triple Output, Buck/Buck/Boost Synchronous Controller 4.5V ≤ VIN ≤ 38V, Boost Output Voltage Up to 60V, 50kHz to 900kHz, 5mm × 7mm QFN-38 and TSSOP-38 Packages LTC3862/LTC3862-1 Multiphase Current Mode Step-Up DC/DC Controllers 4V ≤ VIN ≤ 36V, 5V or 10V Gate Drive, 75kHz to 500kHz, SSOP-24, TSSOP-24, 5mm × 5mm QFN-24 LTC3813/LTC3814-5 100V/60V Maximum VOUT Current Mode Synchronous Step-Up DC/DC Controllers No RSENSE, Large 1Ω Gate Driver, Adjustable Off-Time, SSOP-28, TSSOP-16 LTC1871, LTC1871-1, Wide Input Range, No RSENSE™ Low Quiescent Current Flyback, Boost and SEPIC Controllers LTC1871-7 Adjustable Switching Frequency, 2.5V ≤ VIN ≤ 36V, Burst Mode Operation at Light Load, MSOP-10 LT®3757/LT3758 Boost, Flyback, SEPIC and Inverting Controllers VIN Up to 40V/100V, 100kHz to 1MHz Programmable Operation Frequency, 3mm × 3mm DFN-10 and MSOP-10E LTC3780 High Efficiency Synchronous 4-Switch Buck-Boost DC/ DC Controller 4V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 30V, SSOP-24, 5mm × 5mm QFN-32 3786fa 34 Linear Technology Corporation LT 0911 REV A • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LINEAR TECHNOLOGY CORPORATION 2010