AD AD9237BCPZ-40 3 v low power a/d converter Datasheet

12-Bit, 20 MSPS/40 MSPS/65 MSPS
3 V Low Power A/D Converter
AD9237
Data Sheet
FEATURES
FUNCTIONAL BLOCK DIAGRAM
APPLICATIONS
DRVDD
AVDD
VIN+
SHA
10-STAGE
1 1/2-BIT
PIPELINE
MDAC1
VIN–
4
REFT
A/D
3
15
A/D
REFB
CORRECTION LOGIC
12
MODE2
OE
OTR
OUTPUT BUFFERS
D11
AD9237
VREF
D0
CLOCK
DUTY CYCLE
STABILIZER
SENSE
REF
SELECT
MODE
SELECT
0.5V
AGND
CLK
PDWN
MODE
DGND
05455-001
Ultralow power
85 mW at 20 MSPS
135 mW at 40 MSPS
190 mW at 65 MSPS
SNR = 66 dBc to Nyquist at 65 MSPS
SFDR = 80 dBc to Nyquist at 65 MSPS
DNL = ±0.7 LSB
Differential input with 500 MHz bandwidth
Flexible analog input: 1 V p-p to 4 V p-p range
Offset binary, twos complement, or gray code data formats
Output enable pin
2-step power-down
Full power-down and sleep mode
Clock duty cycle stabilizer
Figure 1.
Ultrasound and medical imaging
Battery-powered instruments
Hand-held scope meters
Low cost digital oscilloscopes
Low power digital still cameras and copiers
Low power communications
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The AD9237 is a family of monolithic, single 3 V supply, 12-bit,
20 MSPS/40 MSPS/65 MSPS analog-to-digital converters
(ADC). This family features a high performance sample-andhold amplifier (SHA) and voltage reference. The AD9237 uses a
multistage differential pipelined architecture with output error
correction logic to provide 12-bit accuracy at 20 MSPS/
40 MSPS/65 MSPS data rates and guarantees no missing codes
over the full operating temperature range.
1. Operating at 65 MSPS, the AD9237 consumes a low 190 mW
at 65 MSPS, 135 mW at 40 MSPS, and 85 mW at 20 MSPS.
2. Power scaling reduces the operating power further when
running at lower speeds.
3. The AD9237 operates from a single 3 V power supply and
features a separate digital output driver supply to
accommodate 2.5 V and 3.3 V logic families.
4. The patented SHA input maintains excellent performance
for input frequencies beyond Nyquist and can be configured
for single-ended or differential operation.
5. The AD9237 is optimized for selectable and flexible input
ranges from 1 V p-p to 4 V p-p.
6. An output enable pin allows for multiplexing of the outputs.
7. Two-step power-down supports a standby mode in addition
to a power-down mode.
8. The OTR output bit indicates when the signal is beyond the
selected input range.
9. The clock duty cycle stabilizer (DCS) maintains converter
performance over a wide range of clock pulse widths.
With significant power savings over previously available ADCs,
the AD9237 is suitable for applications in imaging and medical
ultrasound.
Fabricated on an advanced CMOS process, the AD9237 is
available in a 32-lead LFCSP and is specified over the industrial
temperature range (−40°C to +85°C).
Rev. C
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2005–2014 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD9237* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
TOOLS AND SIMULATIONS
View a parametric search of comparable parts.
• Visual Analog
• AD9237 IBIS Models
DOCUMENTATION
• AD9237LFCSP Analog Input S-Parameter Data
Application Notes
• AN-1142: Techniques for High Speed ADC PCB Layout
REFERENCE MATERIALS
• AN-282: Fundamentals of Sampled Data Systems
Technical Articles
• AN-345: Grounding for Low-and-High-Frequency Circuits
• Correlating High-Speed ADC Performance to Multicarrier
3G Requirements
• AN-501: Aperture Uncertainty and ADC System
Performance
• Matching An ADC To A Transformer
• AN-715: A First Approach to IBIS Models: What They Are
and How They Are Generated
• MS-2210: Designing Power Supplies for High Speed ADC
• AN-737: How ADIsimADC Models an ADC
DESIGN RESOURCES
• AN-741: Little Known Characteristics of Phase Noise
• AD9237 Material Declaration
• AN-742: Frequency Domain Response of SwitchedCapacitor ADCs
• PCN-PDN Information
• AN-756: Sampled Systems and the Effects of Clock Phase
Noise and Jitter
• Symbols and Footprints
• AN-803: Pin Compatible High Speed ADCs Simplify Design
Tasks
DISCUSSIONS
• Quality And Reliability
• AN-827: A Resonant Approach to Interfacing Amplifiers to
Switched-Capacitor ADCs
View all AD9237 EngineerZone Discussions.
• AN-835: Understanding High Speed ADC Testing and
Evaluation
SAMPLE AND BUY
Visit the product page to see pricing options.
• AN-905: Visual Analog Converter Evaluation Tool Version
1.0 User Manual
TECHNICAL SUPPORT
• AN-935: Designing an ADC Transformer-Coupled Front
End
Submit a technical question or find your regional support
number.
Data Sheet
• AD9237: 12-Bit, 20 MSPS/40 MSPS/65 MSPS 3 V Low
Power A/D Converter Data Sheet
DOCUMENT FEEDBACK
Submit feedback for this data sheet.
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
AD9237
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Pin Configuration and Function Descriptions..............................8
Applications ....................................................................................... 1
Terminology .......................................................................................9
Functional Block Diagram .............................................................. 1
Equivalent Circuits ......................................................................... 10
General Description ......................................................................... 1
Typical Performance Characteristics ........................................... 11
Product Highlights ........................................................................... 1
Applying the AD9237 .................................................................... 16
Revision History ............................................................................... 2
Theory of Operation .................................................................. 16
Specifications..................................................................................... 3
Analog Input and Reference Overview ................................... 16
DC Specifications ......................................................................... 3
Voltage Reference ....................................................................... 18
Digital Specifications ................................................................... 4
Clock Input Considerations ...................................................... 19
AC Specifications.......................................................................... 4
Power Dissipation, Power Scaling, and Standby Mode ......... 19
Switching Specifications .............................................................. 5
Digital Outputs ........................................................................... 21
Timing Diagram ............................................................................... 6
Outline Dimensions ....................................................................... 22
Absolute Maximum Ratings ............................................................ 7
Ordering Guide .......................................................................... 22
ESD Caution .................................................................................. 7
REVISION HISTORY
8/14—Rev. B to Rev. C
Changes to Table 7 .......................................................................... 18
Changes to Ordering Guide .......................................................... 22
7/12—Rev. A to Rev. B
Changed CP-32-2 Package to CP-32-7 Package ............. Universal
Changes to Figure 3 .......................................................................... 8
Updated Outline Dimensions ....................................................... 22
Changes to Ordering Guide .......................................................... 22
5/10—Rev. 0 to Rev. A
Changes to Product Highlights Section......................................... 1
Changes to Pipeline Delay Parameter in Table 4 .......................... 5
Changes to Figure 2 .......................................................................... 6
Changes to Figure 3 and Table 6 ..................................................... 8
10/05—Revision 0: Initial Version
Rev. C | Page 2 of 24
Data Sheet
AD9237
SPECIFICATIONS
DC SPECIFICATIONS
AVDD = 3 V, DRVDD = 2.5 V, maximum sample rate, 2 V p-p differential input, −0.5 dBFS input, 1.0 V internal reference, TMIN to TMAX,
unless otherwise noted.
Table 1.
Parameter
RESOLUTION
ACCURACY
No Missing Codes Guaranteed
Offset Error
Gain Error1
Differential Nonlinearity (DNL)2
Integral Nonlinearity (INL)2
TEMPERATURE DRIFT
Offset Error
Gain Error1
INTERNAL VOLTAGE REFERENCE
Output Voltage Error (1 V Mode)
Load Regulation @ 1.0 mA
Output Voltage Error (0.5 V Mode)
Load Regulation @ 0.5 mA
Reference Input Resistance
INPUT REFERRED NOISE
VREF = 0.5 V
VREF = 1.0 V
ANALOG INPUT
Input Span
VREF = 0.5 V; MODE2 = 0 V
VREF = 1.0 V; MODE2 = 0 V
VREF = 0.5 V; MODE2 = AVDD
VREF = 1.0 V; MODE2 = AVDD
Input Capacitance3
POWER SUPPLIES
Supply Voltages
AVDD
DRVDD
Supply Current
IAVDD2
IDRVDD2
PSRR
POWER CONSUMPTION
DC Input4
Sine Wave Input2
Power-Down Mode
Standby Power
Min
12
AD9237BCP-20
Typ
Max
12
Min
12
AD9237BCP-40
Typ
Max
12
±1.30
±0.70
±0.70
±0.90
±1.95
±2.10
±0.95
±1.35
±5
0.8
±2.5
0.1
7
±5
0.8
±2.5
0.1
7
1.35
0.70
2.7
2.25
30.5
3.0
±0.01
85
100
1
20
3.0
2.5
±25
±5
0.8
±2.5
0.1
7
135
150
1
20
±25
2.7
2.25
3.0
2.5
190
210
1
20
mV
mV
mV
mV
kΩ
1
2
2
4
V p-p
V p-p
V p-p
V p-p
pF
3.6
3.6
V
V
64.5
5.5
±0.01
180
Bits
% FSR
% FSR
LSB
LSB
LSB rms
LSB rms
7
3.6
3.6
Unit
Bits
ppm/°C
ppm/°C
1.35
0.70
45.5
4.5
±0.01
120
±1.95
±2.25
+1.25
±2.00
±2
±12
7
3.6
3.6
±1.30
±1.05
±0.70
±0.90
1
2
2
4
7
3.0
2.5
−1.00
1.35
0.70
1
2
2
4
2.7
2.25
±1.95
±2.10
±0.95
±1.35
±2
±12
±25
AD9237BCP-65
Typ
Max
12
±1.30
±0.75
±0.70
±0.90
±2
±12
Min
12
mA
mA
% FSR
270
mW
mW
mW
mW
Gain error and gain temperature coefficient are based on the ADC only (with a fixed 1.0 V external reference).
Measured at maximum clock rate, fIN = 2.4 MHz, full-scale sine wave, with approximately 5 pF loading on each output bit.
3
Input capacitance refers to the effective capacitance between one differential input pin and AGND. Refer to Figure 4 for the equivalent analog input structure.
4
Measured with dc input at maximum clock rate.
1
2
Rev. C | Page 3 of 24
AD9237
Data Sheet
DIGITAL SPECIFICATIONS
Table 2.
Parameter
LOGIC INPUTS
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Input Capacitance
LOGIC OUTPUTS1
DRVDD = 3.3 V
High-Level Output Voltage (IOH = 50 µA)
High-Level Output Voltage (IOH = 0.5 mA)
Low-Level Output Voltage (IOL = 1.6 mA)
Low-Level Output Voltage (IOL = 50 µA)
DRVDD = 2.5 V
High-Level Output Voltage (IOH = 50 µA)
High-Level Output Voltage (IOH = 0.5 mA)
Low-Level Output Voltage (IOL = 1.6 mA)
Low-Level Output Voltage (IOL = 50 µA)
1
AD9237BCP-20
Min
Typ
Max
AD9237BCP-40
Min
Typ
Max
AD9237BCP-65
Min
Typ
Max
2.0
2.0
2.0
0.8
+10
+10
–10
–10
0.8
+10
+10
–10
–10
2
–10
–10
2
3.29
3.25
2
3.29
3.25
3.29
3.25
0.2
0.05
2.49
2.45
0.8
+10
+10
0.2
0.05
2.49
2.45
0.2
0.05
V
V
µA
µA
pF
0.2
0.05
V
V
V
V
0.2
0.05
V
V
V
V
2.49
2.45
0.2
0.05
Unit
Output voltage levels measured with 5 pF load on each output.
AC SPECIFICATIONS
AVDD = 3 V, DRVDD = 2.5 V, maximum sample rate, 2 V p-p differential input, AIN = –0.5 dBFS, 1.0 V internal reference, TMIN to TMAX,
unless otherwise noted.
Table 3.
Parameter
SIGNAL-TO-NOISE RATIO (SNR)
fINPUT = 2.4 MHz
fINPUT = 9.7 MHz
fINPUT = 19.6 MHz
fINPUT = 34.2 MHz
fINPUT = 70 MHz
SIGNAL-TO-NOISE RATIO AND DISTORTION (SINAD)
fINPUT = 2.4 MHz
fINPUT = 9.7 MHz
fINPUT = 19.6 MHz
fINPUT = 34.2 MHz
fINPUT = 70 MHz
EFFECTIVE NUMBER OF BITS (ENOB)
fINPUT = 9.7 MHz
fINPUT = 19.6 MHz
fINPUT = 34.2 MHz
AD9237BCP-20
Min
Typ
Max
AD9237BCP-40
Min
Typ
Max
AD9237BCP-65
Min
Typ
Max
66.8
66.6
66.5
66.5
65.6
65.3
66.6
64.0
65.1
66.0
66.3
66.1
65.9
66.7
66.5
66.4
66.3
64.4
65.8
65.8
65.2
10.6
Bits
Bits
Bits
10.8
10.7
Rev. C | Page 4 of 24
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
66.4
63.5
65.6
Unit
Data Sheet
AD9237
Parameter
SPURIOUS-FREE DYNAMIC RANGE (SFDR)
fINPUT = 2.4 MHz
fINPUT = 9.7 MHz
fINPUT = 19.6 MHz
fINPUT = 34.2 MHz
fINPUT = 70 MHz
WORST HARMONIC (SECOND OR THIRD)
fINPUT = 2.4 MHz
fINPUT = 9.7 MHz
fINPUT = 19.6 MHz
fINPUT = 34.2 MHz
fINPUT = 70 MHz
WORST OTHER SPUR
fINPUT = 2.4 MHz
fINPUT = 9.7 MHz
fINPUT = 19.6 MHz
fINPUT = 34.2 MHz
fINPUT = 70 MHz
AD9237BCP-20
Min
Typ
Max
AD9237BCP-40
Min
Typ
Max
AD9237BCP-65
Min
Typ
Max
88.0
87.5
83.5
85.5
72.4
72.2
82.4
69.4
−72.4
80.5
77.9
80.1
74.9
−88.0
−87.5
−83.5
−85.5
−72.2
−82.4
−69.4
−73.4
−80.5
−77.9
−80.1
−74.9
−90
−90
−90
−90
−73.1
−90
−72.0
−90
−90
−90
−90
Unit
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
SWITCHING SPECIFICATIONS
Table 4.
Parameter
CLK INPUT PARAMETERS
Maximum Conversion Rate
Minimum Conversion Rate
CLK Period
CLK Pulse Width High1
CLK Pulse Width Low1
DATA OUTPUT PARAMETERS
Output Delay (tPD)2
Pipeline Delay (Latency)
Output Enable Time
Output Disable Time
Aperture Delay (tA)
Aperture Uncertainty (Jitter, tJ)
Wake-Up Time (Sleep Mode)3
Wake-Up Time (Standby Mode)3
OUT-OF-RANGE RECOVERY TIME
Min
AD9237BCP-20
Typ
Max
20
Min
AD9237BCP-40
Typ
Max
40
AD9237BCP-65
Typ
Max
65
1
50.0
15.0
15.0
Min
1
25.0
8.8
8.8
3.5
9
6
3
1.0
0.5
3.0
3.0
1
1
15.4
6.2
6.2
3.5
9
6
3
1.0
0.5
3.0
3.0
1
3.5
9
6
3
1.0
0.5
3.0
3.0
2
With duty cycle stabilizer enabled.
Output delay is measured from CLK 50% transition to DATA 50% transition, with 5 pF load on each output.
3
Wake-up time is dependent on value of decoupling capacitors; typical values shown with 0.1 µF and 10 µF capacitors on REFT and REFB.
1
2
Rev. C | Page 5 of 24
Unit
MSPS
MSPS
ns
ns
ns
ns
Cycles
ns
ns
ns
ps rms
ms
µs
Cycles
AD9237
Data Sheet
TIMING DIAGRAM
N
N+1
N+2
N–1
N+3
tA
ANALOG
INPUT
N+8
N+7
N+4
N+5
N+6
DATA
OUT
N–11
N–10
N–9
N–8
N–7
N–6
N–5
N–4
N–3
tPD
Figure 2. Timing Diagram
Rev. C | Page 6 of 24
N–2
N–1
05455-002
CLK
Data Sheet
AD9237
ABSOLUTE MAXIMUM RATINGS
Table 5.
With
Respect to
Pin Name
ELECTRICAL
AVDD
AGND
DRVDD
DGND
AGND
DGND
AVDD
DRVDD
Digital
DGND
Outputs, OE
CLK, MODE,
AGND
MODE2
VIN+, VIN–
AGND
VREF
AGND
SENSE
AGND
REFB, REFT
AGND
PDWN
AGND
ENVIRONMENTAL1
Operating Temperature
Junction Temperature
Lead Temperature (10 sec)
Storage Temperature
1
Min
Max
Unit
–0.3
–0.3
–0.3
–3.9
–0.3
+3.9
+3.9
+0.3
+3.9
DRVDD + 0.3
V
V
V
V
V
−0.3
AVDD + 0.3
V
–0.3
–0.3
–0.3
–0.3
–0.3
AVDD + 0.3
AVDD + 0.3
AVDD + 0.3
AVDD + 0.3
AVDD + 0.3
V
V
V
V
V
–40
+85
150
300
+150
°C
°C
°C
°C
–65
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Absolute maximum ratings are limiting values to be applied
individually and beyond which the serviceability of the circuit
may be impaired. Functional operability is not necessarily
implied. Exposure to absolute maximum rating conditions for
an extended period may affect device reliability.
ESD CAUTION
Typical thermal impedances (32-lead LFCSP), θJA = 32.5°C/W, θJC = 32.71°C/W.
These measurements were taken on a 4-layer board in still air, in accordance
with EIA/JESD51-1.
Rev. C | Page 7 of 24
AD9237
Data Sheet
32
31
30
29
28
27
26
25
AVDD
AGND
VIN–
VIN+
AGND
AVDD
REFT
REFB
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
AD9237
TOP VIEW
(Not to Scale)
24
23
22
21
20
19
18
17
VREF
SENSE
MODE
OTR
D11 (MSB)
D10
D9
D8
NOTES
1. DNC = DO NOT CONNECT.
2. IT IS RECOMMENDED THAT THE EXPOSED PADDLE
BE SOLDERED TO THE GROUND PLANE.
05455-003
D2
D3
D4
D5
D6
D7
DGND
DRVDD
9
10
11
12
13
14
15
16
MODE2
CLK
OE
PDWN
GC
DNC
D0 (LSB)
D1
Figure 3. Pin Configuration
Table 6. Pin Function Descriptions
Pin Number
1
2
3
4
5
6
7 to 14, 17 to 20
15
16
Mnemonic
MODE2
CLK
OE
PDWN
GC
DNC
D0 (LSB) to D11 (MSB)
DGND
DRVDD
21
22
23
24
25
26
27, 32
OTR
MODE
SENSE
VREF
REFB
REFT
AVDD
28, 31
29
30
EP
AGND
VIN+
VIN−
Description
SHA Gain Select and Power Scaling Control (see Table 8).
Clock Input Pin.
Output Enable Pin (Active Low).
Power-Down Function Selection (see Table 9).
Gray Code Control (Active High).
Do Not Connect.
Data Output Bits.
Digital Output Ground.
Digital Output Driver Supply. Must be decoupled to DGND with a minimum 0.1 μF capacitor.
Recommended decoupling is 0.1 μF in parallel with 10 μF.
Out-of-Range Indicator.
Data Format and Clock Duty Cycle Stabilizer (DCS) Mode Selection (see Table 10).
Reference Mode Selection (see Table 7).
Voltage Reference Input/Output (see Table 7).
Differential Reference (−). Must be decoupled to REFT with a minimum 10 μF capacitor.
Differential Reference (+).
Analog Power Supply. Must be decoupled to AGND with a minimum 0.1 μF capacitor.
Recommended decoupling is 0.1 μF in parallel with 10 μF.
Analog Ground.
Analog Input Pin (+).
Analog Input Pin (−).
It is recommended that the exposed paddle be soldered to the ground plane. There is an
increased reliability of the solder joints and maximum thermal capability of the package is
achieved with exposed paddle soldered to the customer board.
Rev. C | Page 8 of 24
Data Sheet
AD9237
TERMINOLOGY
Analog Bandwidth (Full Power Bandwidth)
The analog input frequency at which the spectral power of the
fundamental frequency (as determined by the FFT analysis) is
reduced by 3 dB.
Signal-To-Noise and Distortion (SINAD)1
The ratio of the rms signal amplitude to the rms value of the
sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc.
Aperture Delay (tA)
The delay between the 50% point of the rising edge of the clock
and the instant at which the analog input is sampled.
Effective Number of Bits (ENOB)
The effective number of bits for a device for sine wave inputs
at a given input frequency can be calculated directly from its
measured SINAD using the following formula:
Aperture Jitter (tJ)
The sample-to-sample variation in aperture delay.
ENOB = (SINADdBFS − 1.76)/6.02
Integral Nonlinearity (INL)
The deviation of each individual code from a line drawn from
negative full scale through positive full scale. The point used
as negative full scale occurs ½ LSB before the first code
transition. Positive full scale is defined as a level 1½ LSBs
beyond the last code transition. The deviation is measured
from the middle of each particular code to the true straight line.
Differential Nonlinearity (DNL, No Missing Codes)
An ideal ADC exhibits code transitions that are exactly 1 LSB
apart. DNL is the deviation from this ideal value. Guaranteed
no missing codes to 12-bit resolution indicates that all 4096
codes must be present over all operating ranges.
Offset Error
The major carry transition should occur for an analog value
½ LSB below VIN+ = VIN–. Offset error is defined as the
deviation of the actual transition from that point.
Gain Error
The first code transition should occur at an analog value
½ LSB above negative full scale. The last transition should occur
at an analog value 1½ LSB below the positive full scale. Gain
error is the deviation of the actual difference between first and
last code transitions and the ideal difference between first and
last code transitions.
Temperature Drift
The temperature drift for offset error and gain error specifies
the maximum change from the initial (25°C) value to the value
at TMIN or TMAX.
Power Supply Rejection Ratio
The change in full scale from the value with the supply at the
minimum limit to the value with the supply at its maximum
limit.
Total Harmonic Distortion (THD)1
The ratio of the rms sum of the first six harmonic components
to the rms value of the measured input signal.
Signal-to-Noise Ratio (SNR)1
The ratio of the rms signal to the rms value of the sum of all
other spectral components below the Nyquist frequency,
excluding the first six harmonics and dc.
Spurious-Free Dynamic Range (SFDR)1
SFDR is the difference in dB between the rms amplitude of the
input signal and the rms value of the peak spurious signal. The
peak spurious signal may not be an harmonic.
Two-Tone SFDR1
The ratio of the rms value of either input tone to the rms value
of the peak spurious component. The peak spurious component
may or may not be an IMD product.
Clock Pulse Width and Duty Cycle
Pulse width high is the minimum amount of time that the clock
pulse should be left in the Logic 1 state to achieve rated
performance. Pulse width low is the minimum time the clock
pulse should be left in the low state. At a given clock rate, these
specifications define an acceptable clock duty cycle.
Minimum Conversion Rate
The clock rate at which the SNR of the lowest analog signal
frequency drops by no more than 3 dB below the guaranteed
limit.
Maximum Conversion Rate
The clock rate at which parametric testing is performed.
Output Propagation Delay (tPD)
The delay between the clock logic threshold and the time when
all bits are within valid logic levels.
Out-of-Range Recovery Time
The time it takes the ADC to reacquire the analog input after a
transition from 10% above positive full scale to 10% above
negative full scale, or from 10% below negative full scale to 10%
below positive full scale.
1
AC specifications may be reported in dBc (degrades as signal levels are
lowered) or in dBFS (always related back to converter full scale).
Rev. C | Page 9 of 24
AD9237
Data Sheet
EQUIVALENT CIRCUITS
DRVDD
AVDD
VIN+, VIN–
05455-006
05455-004
D11–D0,
OTR
Figure 4. Equivalent Analog Input Circuit
375Ω
CLK,
PDWN
05455-007
70kΩ
375Ω
05455-005
MODE,
MODE2,
GC, OE
Figure 6. Equivalent Digital Output Circuit
Figure 5. Equivalent MODE, MODE2, GC, OE Input Circuit
Figure 7. Equivalent CLK, PDWN Input Circuit
Rev. C | Page 10 of 24
Data Sheet
AD9237
TYPICAL PERFORMANCE CHARACTERISTICS
AVDD = 3.0 V, DRVDD = 2.5 V, maximum sample rate with DCS disabled, TA = 25°C, 2 V p-p differential input, AIN = –0.5 dBFS,
VREF = 1.0 V internal, FFT length 16 K, unless otherwise noted.
90
0
SFDR
–20
85
–40
80
SNR/SFDR (dBc)
AMPLITUDE (dBFS)
SNR = 66.9dBc
SFDR = 87.0dBc
–60
–80
75
70
SNR
–100
–120
0
2
4
6
FREQUENCY (MHz)
8
60
10.0
10
Figure 8. AD9237-20 10 MHz FFT
05455-011
05455-008
65
12.5
15.0
17.5
CLOCK FREQUENCY (MSPS)
20.0
Figure 11. AD9237-20 SNR/SFDR vs. Clock Frequency with fIN = 10 MHz
0
90
SNR = 66.8dBc
SFDR = 83.1dBc
85
SFDR
–40
SNR/SFDR (dBc)
–60
–80
80
75
70
05455-009
–100
–120
0
2
4
6
8
10
12
14
FREQUENCY (MHz)
16
18
SNR
65
20
20
Figure 9. AD9237-40 20 MHz FFT
05455-012
AMPLITUDE (dBFS)
–20
25
30
35
CLOCK FREQUENCY (MSPS)
40
Figure 12. AD9237-40 SNR/SFDR vs. Clock Frequency with fIN = 20 MHz
0
90
SNR = 66.0dBc
SFDR = 78.6dBc
–20
85
–40
80
SNR/SFDR (dBc)
–60
–80
75
70
SNR
–100
–120
0
5
10
15
20
FREQUENCY (MHz)
25
30 32.5
Figure 10. AD9237-65 70 MHz FFT
60
40
05455-013
65
05455-010
AMPLITUDE (dBFS)
SFDR
45
50
55
CLOCK FREQUENCY (MSPS)
60
65
Figure 13. AD9237-65 SNR/SFDR vs. Clock Frequency with fIN = 35 MHz
Rev. C | Page 11 of 24
AD9237
Data Sheet
0
90
SFDR DCS
ENABLED
SNR = 65.6dBc
SFDR = 67.1dBc
85
–20
SNR/SFDR (dBc)
AMPLITUDE (dBc)
80
–40
–60
–80
SFDR DCS
DISABLED
75
70
SNR DCS ENABLED
65
60
SNR DCS DISABLED
–100
–120
0
5
10
15
20
FREQUENCY (MHz)
25
05455-030
05455-014
55
50
30
30 32.5
35
Figure 14. AD9237-65 100 MHz FFT
65
70
SFDR dBFS 2V p-p
80
SNR/SFDR (dBc and dBFS)
SFDR dBFS 2V p-p
SNR dBFS 2V p-p
SNR dBFS 4V p-p
60
SFDR dBc 4V p-p
SFDR dBc 2V p-p
50
70
SFDR dBc 1V p-p
SNR dBFS 1V p-p
60
50
SNR dBc 1V p-p
40
05455-017
40
SFDR dBFS 1V p-p
SFDR dBc 2V p-p
SNR dBFS 2V p-p
SNR dBc 2V p-p
SNR dBc 4V p-p
30
–30
–25
–20
–15
–10
INPUT AMPLITUDE (dBFS)
–5
SNR dBc 2V p-p
30
–30
0
Figure 15. AD9237-65 SNR/SFDR vs. Input Amplitude with fIN = 35 MHz
05455-018
80
–25
–20
–15
–10
INPUT AMPLITUDE (dBFS)
–5
0
Figure 18. AD9237-65 SNR/SFDR vs. Input Amplitude with fIN = 35 MHz
100
100
SFDR dBFS 2V p-p
SFDR dBFS 2V p-p
90
SNR/SFDR (dBc and dBFS)
90
SFDR dBc 2V p-p
80
SFDR dBFS 1V p-p
SFDR dBc 1V p-p
70
60
SNR dBFS 2V p-p
SNR dBFS 1V p-p
50
40
05455-019
SNR dBc 2V p-p
SNR dBc 1V p-p
30
–30
–25
–20
–15
–10
INPUT AMPLITUDE (dBFS)
–5
0
Figure 16. AD9237-40 SNR/SFDR vs. Input Amplitude with fIN = 20 MHz
Rev. C | Page 12 of 24
80 SFDR dBFS 1V p-p
SFDR dBc 2V p-p
SFDR dBc 1V p-p
70
60
SNR dBFS 2V p-p
SNR dBFS 1V p-p
50
40
SNR dBc 2V p-p
05455-020
SNR/SFDR (dBc and dBFS)
60
90
SFDR dBFS 4V p-p
SNR/SFDR (dBc and dBFS)
45
50
55
DUTY CYCLE (%)
Figure 17. SNR/SFDR vs. Clock Duty Cycle
90
70
40
SNR dBc 1V p-p
30
–30
–25
–20
–15
–10
INPUT AMPLITUDE (dBFS)
–5
0
Figure 19. AD9237-20 SNR/SFDR vs. Input Amplitude with fIN = 10 MHz
Data Sheet
AD9237
0
100
SNR = 67.0dBFS
SFDR = 87.8dBFS
90
SNR/SFDR (dBc and dBFS)
–40
–60
–80
–100
0
5
10
15
20
FREQUENCY (MHz)
25
60
SFDR dBc
50
SNR dBc
30
–30
–25
30 32.5
Figure 20. AD9237-65 Two-Tone FFT, fIN1 = 45 MHz, fIN2 = 46 MHz
70 SNR dBFS
40
05455-095
–120
SFDR dBFS
80
05455-024
AMPLITUDE (dBc)
–20
–20
–15
INPUT AMPLITUDE (AIN)
–10
–6.5
Figure 23. AD9237-65 Two-Tone SNR/SFDR , vs. Analog Input with
fIN1 = 45 MHz, fIN2 = 46 MHz
0
100
SNR = 67.2dBFS
SFDR = 88.3dBFS
90
SFDR dBFS
SNR/SFDR (dBc and dBFS)
–40
–60
–80
–100
0
5
10
FREQUENCY (MHz)
15
60
SFDR dBc
50
SNR dBc
30
–30
–25
20
Figure 21. AD9237-40 Two-Tone FFT
fIN1 = 45 MHz, fIN2 = 46 MHz
70 SNR dBFS
40
05455-021
–120
80
05455-025
AMPLITUDE (dBc)
–20
–20
–15
INPUT AMPLITUDE (AIN)
–10
–6.5
Figure 24. AD9237-40 Two-Tone SNR/SFDR , vs. Analog Input with
fIN1 = 45 MHz, fIN2 = 46 MHz
0
100
SNR = 66.9dBFS
SFDR = 84.1dBFS
90
SNR/SFDR (dBc and dBFS)
–40
–60
–80
05455-094
–100
–120
0
5
10
15
20
FREQUENCY (MHz)
25
30
Figure 22. AD9237-65 Two-Tone FFT, fIN1 = 69 MHz, fIN2 = 70 MHz
SFDR dBFS
80
70 SNR dBFS
60
SFDR dBc
50
40
SNR dBc
30
–30
–25
05455-098
AMPLITUDE (dBFS)
–20
–20
–15
INPUT AMPLITUDE (AIN)
–10
–6.5
Figure 25. AD9237-65 Two-Tone SNR/SFDR vs. Analog Input with
fIN1 = 69 MHz, fIN2 = 70 MHz
Rev. C | Page 13 of 24
AD9237
Data Sheet
0
100
SNR = 67.1dBFS
SFDR = 87.3dBFS
90
–20
SNR/SFDR (dBc and dBFS)
–40
–60
–80
–100
0
5
10
FREQUENCY (MHz)
15
SFDR dBc
50
SNR dBc
30
–30
–25
20
Figure 26. AD9237-40 Two-Tone FFT
fIN1 = 69 MHz, fIN2 = 70 MHz
60
40
05455-026
–120
70 SNR dBFS
05455-097
AMPLITUDE (dBc)
SFDR dBFS
80
–20
–15
INPUT AMPLITUDE (AIN)
–10
–6.5
Figure 29. AD9237-40 Two-Tone SNR/SFDR vs. Analog Input with
fIN1 = 69 MHz, fIN2 = 70 MHz
90
90
85
85
SFDR
SFDR
75
70
SNR
70
SNR
65
65
60
60
0
25
50
75
INPUT FREQUENCY (MHz)
100
55
0
125
Figure 27. AD9237-65 SNR/SFDR vs. Input Frequency
0.75
0.75
0.50
0.50
0.25
0.25
DNL (LSB)
1.00
0
–0.50
–0.50
–0.75
–0.75
05455-032
–0.25
512
1024
1536
2048
CODE
2560
3072
3584
100
125
0
–0.25
0
50
75
INPUT FREQUENCY (MHz)
Figure 30. AD9237-40 SNR/SFDR vs. Input Frequency
1.00
–1.00
25
4096
Figure 28. Typical INL
05455-035
55
INL (LSB)
75
05455-016
SNR/SFDR (dBc)
80
05455-015
SNR/SFDR (dBc)
80
–1.00
0
512
1024
1536
2048
CODE
2560
Figure 31. Typical DNL
Rev. C | Page 14 of 24
3072
3584
4096
Data Sheet
AD9237
67.5
85
10.83
AD9237-20
SNR
10.75
AD9237-65
66.0
10.67
ENOB (Bits)
66.5
80
75
70
SFDR
65.0
10
10.59
20
30
40
50
CLOCK FREQUENCY (MSPS)
60
10.50
70
65
Figure 32. AD9237 SINAD/ENOB vs. Clock Frequency with fIN = Nyquist
Rev. C | Page 15 of 24
60
–40
05455-063
65.5
05455-062
SINAD (dBc)
AD9237-40
SNR/SFDR (dBc)
67.0
90
–20
0
20
40
TEMPERATURE (°C)
60
80 85
Figure 33. AD9237-65 SNR/SFDR vs. Temperature with fIN = 32.5MHz
AD9237
Data Sheet
APPLYING THE AD9237
THEORY OF OPERATION
90
2.5MHz SFDR
The AD9237 uses a calibrated, 11-stage pipeline architecture
with a patented input SHA implemented. Each stage of the
pipeline, excluding the last, consists of a low resolution flash
ADC connected to a switched capacitor digital-to-analog
converter (DAC) and an interstage residue amplifier (MDAC).
The MDAC magnifies the difference between the reconstructed
DAC output and the flash input for the next stage in the
pipeline. One bit of redundancy is used in each stage to facilitate
digital correction of flash errors. The last stage consists of a
flash ADC.
The input stage contains a differential SHA that can be ac- or
dc-coupled in differential or single-ended modes. The outputstaging block aligns the data, carries out the error correction,
and passes the data to the output buffers. The output buffers
are powered from a separate supply, allowing adjustment of
the output voltage swing. During power-down and stand-by
operation, the output buffers go into a high impedance state.
The ADC samples the analog input on the rising edge of
the clock. System disturbances just prior to, or immediately
following, the rising edge of the clock and/or excessive clock
jitter can cause the SHA to acquire the wrong input value and
should be minimized.
34.2MHz SFDR
SNR/SFDR (dBc)
70
2.5MHz SNR
34.2MHz SNR
60
50
40
05455-038
The pipelined architecture permits the first stage to operate on a
new input sample, while the remaining stages operate on preceding
samples. While the converter captures a new input sample every
clock cycle, it takes eight clock cycles for the conversion to be
fully processed and to appear at the output, as shown in Figure 2.
80
30
0
0.5
1.0
1.5
2.0
INPUT COMMON-MODE LEVEL (V)
2.5
3.0
Figure 34. AD9237-65 SNR/SFDR vs. Input Common-Mode Level
In addition, a small shunt capacitor placed across the inputs
provides dynamic charging currents. This passive network
creates a low-pass filter at the ADC’s input; therefore, the
precise values are dependent on the application. In IF undersampling applications, the shunt capacitor(s) should be reduced
or removed depending on the input frequency. In combination
with the driving source impedance, the capacitors limit the
input bandwidth.
H
T
T
5pF
VIN+
CPAR
ANALOG INPUT AND REFERENCE OVERVIEW
T
Figure 35 shows the clock signal alternately switching the
SHA between sample mode and hold mode. When the SHA is
switched into sample mode, the signal source must be capable
of charging the sample capacitors and settling within one-half
of a clock cycle. A small resistor in series with each input can
help reduce the peak transient current required from the output
stage of the driving source.
5pF
VIN–
CPAR
T
H
05455-039
The analog input to the AD9237 is a differential switched
capacitor SHA that has been designed for optimum
performance while processing a differential input signal.
The SHA input can support a wide common-mode range
and maintain excellent performance, as shown in Figure 34.
An input common-mode voltage of midsupply minimizes
signal-dependant errors and provides optimum performance.
Figure 35. Switched-Capacitor SHA Input
For best dynamic performance, the source impedances driving
VIN+ and VIN– should be matched so that common-mode
settling errors are symmetrical. These errors are reduced by the
common-mode rejection of the ADC.
An internal differential reference buffer creates positive and
negative reference voltages, REFT and REFB, that define the
span of the ADC core.
Rev. C | Page 16 of 24
Data Sheet
AD9237
The output common mode of the reference buffer is set to midsupply, and the REFT and REFB voltages and input span are
defined as:
1k
AVDD
33
VIN+
+
2V p-p
REFT = ½(AVDD + VREF)
1.2k 0.1F
15pF
AD8351
49.9
0.1F
–
REFB = ½(AVDD − VREF)
25
AD9237
33
VIN–
0.1F
AGND
1k
4  REFT  REFB 
4  VREF
Span 

Span _ Factor
Span _ Factor
05455-041
25
0.1F
Figure 36. Differential Input Configuration Using the AD8351
The previous equations show that the REFT and REFB voltages
are symmetrical about the midsupply voltage, and the input
span is proportional to the value of the VREF voltage, see Table 7
for more details.
The internal voltage reference can be pin strapped to fixed
values of 0.5 V or 1.0 V, or adjusted within this range as
discussed in the Internal Reference Connection section.
Maximum SNR performance is achieved with the AD9237
set to an input span of 2 V p-p or greater. The relative SNR
degradation is 3 dB when changing from 2 V p-p mode to
1 V p-p mode.
At input frequencies in the second Nyquist zone and above, the
performance of most amplifiers is not adequate to achieve the
true performance of the AD9237. This is especially true in IF
undersampling applications where frequencies in the 70 MHz
to 100 MHz range are being sampled. For these applications,
differential transformer coupling is the recommended input
configuration, as shown in Figure 37.
AVDD
33
2V p-p
15pF
49.9
The SHA must be driven from a source that keeps the signal
peaks within the allowable range for the selected reference
voltage. The minimum and maximum common-mode input
levels are defined as:
33
1k
0.1F
VCMMIN = VREF/2
VIN+
AD9237
VIN–
AGND
05455-042
1k
Figure 37. Differential Transformer-Coupled Configuration
VCMMAX = (AVDD + VREF)/2
The minimum common-mode input level allows the AD9237 to
accommodate ground-referenced inputs.
Although optimum performance is achieved with a differential
input, a single-ended source can be driven into VIN+ or VIN–.
In this configuration, one input accepts the signal while the
opposite input should be set to midscale by connecting it to an
appropriate reference. For example, a 2 V p-p signal can be
applied to VIN+ while a 1 V reference is applied to VIN–. The
AD9237 then accepts an input signal varying between 2 V and
0 V. In the single-ended configuration, distortion performance
may degrade significantly as compared to the differential case.
However, the effect is less noticeable at lower input frequencies and
in the lower speed grade models (AD9237-40 and AD9237-20).
The signal characteristics must be considered when selecting a
transformer. Most RF transformers saturate at frequencies
below a few MHz, and excessive signal power can cause core
saturation, which leads to distortion.
Single-Ended Input Configuration
A single-ended input can provide adequate performance in
cost-sensitive applications. In this configuration, there is
degradation in SFDR and distortion performance due to the
large input common-mode swing. However, if the source
impedances on each input are matched, there should be little
effect on SNR performance. Figure 38 details a typical singleended input configuration.
0.1F
Differential Input Configurations
Rev. C | Page 17 of 24
2V p-p
1k
1k
49.9
0.1F
1k
AVDD
33
15pF
33
VIN+
AD9237
VIN–
AGND
25
05455-099
As previously detailed, optimum performance is achieved while
driving the AD9237 in a differential input configuration. For
baseband applications, the AD8351 differential driver provides
excellent performance and a flexible interface to the ADC. The
output common-mode voltage of the AD8351 is easily set to
AVDD/2, and the driver can be configured in a Sallen-Key filter
topology to provide band limiting of the input signal. Figure 36
details a typical configuration using the AD8351.
1k
Figure 38. Single-Ended Input Configuration
AD9237
Data Sheet
Table 7. Reference Configuration Summary
Selected Mode
External Reference
SENSE Voltage
AVDD
Resulting VREF (V)
N/A
Span Factor
2
Resulting Differential Span (V p-p)
4 × External Reference
Span _ Factor
Internal Fixed Reference
VREF
0.5
Programmable Reference
0.2 V to VREF
0.5 × (1 + R2/R1)
(See Figure 40)
Internal Fixed Reference
AGND to 0.2 V
1.0
1
2
1
2
1.0 V
2.0 V
4 × VREF
Span _ Factor
1
2
1
2.0 V
4.0 V
VOLTAGE REFERENCE
VIN+
A stable and accurate 0.5 V voltage reference is built into
the AD9237. The input range can be adjusted by varying
the reference voltage applied to the AD9237, using either the
internal reference or an externally applied reference voltage.
The input span of the ADC tracks reference voltage changes
linearly.
REFT
0.1µF
ADC
CORE
+
0.1µF
10µF
REFB
0.1µF
VREF
10µF
+
0.1µF
0.5V
SELECT
LOGIC
SENSE
AD9237
05455-043
In all reference configurations, REFT and REFB drive the
A/D conversion core and, in conjunction with the span factor,
establish its input span. The input range of the ADC always
equals four times the voltage at the reference pin divided by
the span factor for either an internal or an external reference.
It is required to decouple REFT to REFB with 0.1 µF and 10 µF
decoupling capacitors, as shown in Figure 39.
VIN–
Figure 39. Internal Reference Configuration
Internal Reference Connection
A comparator within the AD9237 detects the potential at
the SENSE pin and configures the reference into one of four
possible states, which are summarized in Table 7. If SENSE is
grounded, the reference amplifier switch is connected to the
internal resistor divider, setting VREF to 1 V (see Figure 39).
Connecting the SENSE pin to VREF switches the reference
amplifier output to the SENSE pin, completing the loop and
providing a 0.5 V reference output. If a resistor divider is
connected, as shown in Figure 40, then the switch is again set to
the SENSE pin. This puts the reference amplifier in a noninverting mode with the VREF output defined as
VIN+
VIN–
REFT
0.1µF
ADC
CORE
+
0.1µF
10µF
REFB
0.1µF
VREF
10µF
+
0.1µF
R2
0.5V
SELECT
LOGIC
SENSE
AD9237
Figure 40. Programmable Reference Configuration
Rev. C | Page 18 of 24
05455-044
R1
R2 
VREF = 0.5 × 1 +

R1 

Data Sheet
AD9237
External Reference Operation
CLOCK INPUT CONSIDERATIONS
The use of an external reference may be necessary to enhance
the gain accuracy of the ADC or to improve thermal drift
characteristics. Figure 41 shows the typical drift characteristics
of the internal reference in both 1 V and 0.5 V modes. When
multiple ADCs track one another, a single reference (internal or
external) reduces gain matching errors.
Typical high speed ADCs use both clock edges to generate
a variety of internal timing signals and, as a result, can be
sensitive to clock duty cycle. Commonly a 5% tolerance is
required on the clock duty cycle to maintain dynamic
performance characteristics. The AD9237 contains a clock
duty cycle stabilizer (DCS) that retimes the nonsampling, or
falling edge, providing an internal clock signal with a nominal
50% duty cycle. This allows a wide range of clock input duty
cycles without affecting the performance of the AD9237. As
shown in Figure 17, noise and distortion performance are
nearly flat over a 30% range of duty cycle with the DCS enabled.
When the SENSE pin is connected to AVDD, the internal
reference is disabled, allowing the use of an external reference.
An internal reference buffer loads the external reference with
an equivalent 7 kΩ load. The internal buffer still generates the
positive and negative full-scale references, REFT and REFB, for
the ADC core. The input span is always four times the value of
the reference voltage divided by the span factor; therefore, the
external reference must be limited to a maximum of 1 V.
0.7
High speed, high resolution ADCs are sensitive to the quality
of the clock input. The degradation in SNR at a given full-scale
input frequency (fINPUT) due only to rms aperture jitter (tJ) can
be calculated by
0.6
VREF ERROR (%)
0.5
1V REFERENCE
0.4

1
SNR Degradation = 20 log 10 
 2πf INPUT t J
0.3
0.2
0
–40
05455-046
0.1
–20
0
20
40
TEMPERATURE (°C)
60
80 85
Figure 41. Typical VREF Drift
If the internal reference of the AD9237 is used to drive multiple
converters to improve gain matching, the loading of the reference by the other converters must be considered. Figure 42
shows how the internal reference voltage is affected by loading.
A 2 mA load is the maximum recommended load.
0.05



In this equation, the rms aperture jitter represents the rootsum-square of all jitter sources, which include the clock input,
analog input signal, and ADC aperture jitter specification.
Undersampling applications are particularly sensitive to jitter.
0.5V REFERENCE
The clock input should be treated as an analog signal in
cases where aperture jitter can affect the dynamic range of the
AD9237. Power supplies for clock drivers should be separated
from the ADC output driver supplies to avoid modulating the
clock signal with digital noise. Low jitter, crystal-controlled
oscillators make the best clock sources. If the clock is generated
from another type of source (such as gating, dividing, or other
methods), then it should be retimed by the original clock at the
last step.
The lowest typical conversion rate of the AD9237 is 1 MSPS. At
clock rates below 1 MSPS, dynamic performance may degrade.
0
–0.05
POWER DISSIPATION, POWER SCALING, AND
STANDBY MODE
0.5V ERROR (%)
–0.10
1V ERROR (%)
–0.15
–0.20
05455-093
ERROR (%)
The duty cycle stabilizer uses a delay-locked loop (DLL) to
create the nonsampling edge. As a result, any changes to the
sampling frequency require approximately 100 clock cycles to
allow the DLL to acquire and lock to the new rate.
–0.25
0
0.5
1.0
1.5
LOAD (mA)
2.0
2.5
3.0
As shown in Figure 43, the power dissipated by the AD9237 is
proportional to its sample rate. The digital power dissipation
does not vary substantially between the three speed grades
because it is determined primarily by the strength of the digital
drivers and the load on each output bit. The maximum DRVDD
current can be calculated as
I DRVDD = VDRVDD × C LOAD × f CLK × N
Figure 42. VREF Accuracy vs. Load
where N is 12, the number of output bits.
Rev. C | Page 19 of 24
AD9237
Data Sheet
190
This maximum current occurs when every output bit switches
on every clock cycle, that is, a full-scale square wave at the
Nyquist frequency, fCLK/2. In practice, the DRVDD current is
established by the average number of output bits switching,
which is determined by the encode rate and the characteristics
of the analog input signal.
170
AD9237-65
POWER (mW)
150
190
130
110
170
AD9237-40
POWER (mW)
AD9237-20
70
10
130
AD9237-65
20
30
40
50
SAMPLE RATE (MSPS)
60
65
Figure 44. Total Power vs. Sample Rate with Power Scaling Enabled
110
AD9237-40
05455-047
90
AD9237-20
70
10
05455-096
90
150
20
30
40
50
SAMPLE RATE (MSPS)
60
65
The MODE2 pin is a multilevel input that controls the span
factor and power scaling modes. The MODE2 pin is internally
pulled down to AGND by a 70 kΩ resistor. The input threshold
and corresponding mode selections are outlined in Table 8.
Table 8. MODE2 Selection
Figure 43. Total Power vs. Sample Rate with fIN = 10 MHz
For the AD9237-20 speed grade, the digital power consumption
can represent as much as 10% of the total dissipation. Digital
power consumption can be minimized by reducing the
capacitive load presented to the output drivers. The data in
Figure 43 was taken with a 5 pF load on each output driver.
The AD9237 is designed to provide excellent performance with
minimum power. The analog circuitry is optimally biased so
that each speed grade provides excellent performance while
affording reduced power consumption. Each speed grade
dissipates a baseline power at low sample rates that increases
linearly with the clock frequency, as shown in Figure 43.
The power scaling feature provides an additional power savings
when enabled, as shown in Figure 44. The power scaling mode
cannot be enabled if the clock is varied during operation. This is
because the internal circuitry cannot quickly track a changing
clock, and the part does not have enough power to operate
properly.
MODE2 Voltage
AVDD
2/3 AVDD
1/3 AVDD
AGND (Default)
Span Factor
1
1
2
2
Power Scaling
Disabled
Enabled
Enabled
Disabled
The PDWN pin is a multilevel input that controls the power
states. The input threshold values and corresponding power
states are outlined in Table 9.
Table 9. PDWN Selection
PDWN Voltage
AVDD
1/3 AVDD
AGND (Default)
Power State
Power-Down Mode
Standby Mode
Normal Operation
Power (mW)
1
20
Based on speed grade
By asserting the PDWN pin high, the AD9237 is placed in
power-down mode. In this state, the ADC typically dissipates
1 mW. During power-down, the output drivers are placed in a
high impedance state. Low power dissipation in power-down
mode is achieved by shutting down the reference, reference
buffer, biasing networks, clock, and duty cycle stabilizer
circuitry. The decoupling capacitors on REFT and REFB are
discharged when entering power-down mode and then must
be recharged when returning to normal operation.
As a result, the wake-up time is related to the time spent
in power-down mode and shorter standby cycles result in
proportionally shorter wake-up times. With the recommended
0.1 μF and 10 μF decoupling capacitors on REFT and REFB, it
takes approximately 1 sec to fully discharge the reference buffer
decoupling capacitors and 3 ms to restore full operation.
Rev. C | Page 20 of 24
Data Sheet
AD9237
DIGITAL OUTPUTS
The AD9237 output drivers can be configured to interface with
2.5 V or 3.3 V logic families by matching DRVDD to the digital
supply of the interfaced logic. The output drivers are sized to
provide sufficient output current to drive a wide variety of logic
families. However, large drive currents tend to cause current
glitches on the supplies that can affect converter performance.
Applications requiring the ADC to drive large capacitive loads
or large fanouts may require external buffers or latches.
The length of the output data lines and loads placed on them
should be minimized to reduce transients within the AD9237;
these transients can detract from the converter’s dynamic
performance.
As detailed in Table 10, the data format can be selected for
either offset binary, twos complement, or gray code.
completed. By logically AND-ing OTR with the MSB and its
complement, overrange high or underrange low conditions can
be detected. Table 11 is a truth table for the overrange/ underrange circuit in Figure 46, which uses NAND gates. Systems
requiring programmable gain condition of the AD9237 can,
after eight clock cycles, detect an out-of-range condition;
therefore, eliminating gain selection iterations. In addition,
OTR can be used for digital offset and gain calculation.
OTR DATA OUTPUTS
1
1111 1111 1111
0
1111 1111 1111
0
1111 1111 1110
+FS – 1 LSB
+FS
–FS + 1/2 LSB
0
0000 0000 0001
0
0000 0000 0000
0
0000 0000 0000
–FS
–FS – 1/2 LSB
Operational Mode Selection
The gray code output format is obtained by connecting GC to
AVDD. When the part is in gray code mode, the MODE pin
controls the DCS function only. The GC pin is internally pulled
down to AGND by a 70 kΩ resistor.
Table 10. MODE Selection
Data Format
Twos Complement
Twos Complement
Offset Binary
Offset Binary
–FS – 1/2 LSB
Figure 45. OTR Relation to Input Voltage and Output Data
Table 11. Output Data Format
OTR
0
0
1
1
MSB
0
1
0
1
Analog Input Is
Within range
Within range
Underrange
Overrange
MSB
OVER = 1
OTR
UNDER = 1
MSB
Duty Cycle Stabilizer
Disabled
Enabled
Enabled
Disabled
Out of Range (OTR)
An out-of-range condition exists when the analog input voltage
is beyond the input range of the ADC. The OTR pin is a digital
output that is updated along with the data output corresponding
to the particular sampled input voltage. Therefore, the OTR pin
has the same pipeline latency as the digital data. OTR is low
when the analog input voltage is within the analog input range,
and high when the analog input voltage exceeds the input range,
as shown in Figure 45. OTR remains high until the analog input
returns to within the input range and another conversion is
05455-050
The AD9237 can output data in either offset binary, twos
complement, or gray code format. There is also a provision
for enabling or disabling the duty cycle stabilizer (DCS).
The MODE pin is a multilevel input that controls the data
format (except for gray code) and DCS state. The MODE pin
is internally pulled down to AGND by a 70 kΩ resistor. The
input threshold values and corresponding mode selections are
outlined in Table 10.
MODE Voltage
AVDD
2/3 AVDD
1/3 AVDD
AGND (Default)
OTR
05455-049
By asserting the PDWN pin to AVDD/3, the AD9237 is placed
in standby mode. In this state, the ADC typically dissipates
20 mW. The output drivers are placed in a high impedance
state. The reference circuitry is enabled, allowing for a quick
start upon bringing the ADC into normal operating mode.
Figure 46. Overrange/Underrange Logic
Digital Output Enable Function (OE)
The AD9237 has three-state ability. The OE pin is internally
pulled down to AGND by a 70 kΩ resistor. If the OE pin is low,
the output data drivers are enabled. If the OE pin is high, the
output data drivers are placed in a high impedance state. It is
not intended for rapid access to the data bus. Note that the
OE pin is referenced to the digital supplies (DRVDD) and
should not exceed that voltage.
Timing
The AD9237 provides latched data outputs with a pipeline delay
of eight clock cycles. Data outputs are available one propagation
delay (tPD) after the rising edge of the clock signal. Refer to
Figure 2 for a detailed timing diagram.
Rev. C | Page 21 of 24
AD9237
Data Sheet
OUTLINE DIMENSIONS
0.30
0.25
0.18
32
25
0.50
BSC
TOP VIEW
0.80
0.75
0.70
8
16
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
3.25
3.10 SQ
2.95
EXPOSED
PAD
17
0.50
0.40
0.30
PIN 1
INDICATOR
1
24
9
BOTTOM VIEW
0.25 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WHHD.
112408-A
PIN 1
INDICATOR
5.10
5.00 SQ
4.90
Figure 47. 32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
5 mm × 5 mm Body, Very Very Thin Quad
(CP-32-7)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
AD9237BCPZ-40
AD9237BCPZRL7-40
1
2
Temperature Range
–40°C to +85°C
–40°C to +85°C
Package Description
32-Lead Lead Frame Chip Scale Package (LFCSP_WQ)
32-Lead Lead Frame Chip Scale Package (LFCSP_WQ)
Z = RoHS-Compliant Part.
Formerly CP-32-2 package.
Rev. C | Page 22 of 24
Package Option2
CP-32-7
CP-32-7
Data Sheet
AD9237
NOTES
Rev. C | Page 23 of 24
AD9237
Data Sheet
NOTES
© 2005–2014 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05455–0–8/14(C)
Rev. C | Page 24 of 24