Wall JFC48S05-30GHC 30 watt dc/dc power converter Datasheet

JFC30 SERIES
30 Watt DC/DC Power Converters
Rev B
FEATURES
• High Efficiency up to 93%
• 30 Watts Maximum Output Power
• Remote ON/OFF Control
• 1600VDC I/O Isolation
• 2:1 Wide Input Voltage Ranges
• Short Circuit, Over Voltage, Over Load, & Over Temperature
• Six-Sided Continuous Shielding
• Ultra Low Quiescent Current
Protection
• Wide Operating Temperature Range: -40°C to +100°C
• No Minimum Load Requirements • Compliant to RoHS EU Directive 2011/65/EU
• Single and Dual Outputs
Size:
1.00 x 1.00 x 0.39 inches
(25.4 x 25.4 x 9.9 mm)
Options
• Negative Logic Remote ON/OFF
• Without Trim pin
• Without CTRL Pin
• Heatsink
• UL60950-1, EN60950-1, & IEC60950-1 Safety Approvals
• Optional Heatsink Available (Suffix “HC”)
DESCRIPTION
The JFC30 series of DC/DC power converters provides 30 Watts of output power in an industry standard
1.00” x 1.00” x 0.39” package and footprint. This series has single and dual output models with 2:1 wide
input voltage ranges of 9-18VDC, 18-36VDC, and 36-75VDC. Some features include high efficiency up to
93%, 1600VDC I/O isolation, six-sided shielding, and remote ON/OFF control. These converters are also
protected against short circuit, over voltage, over load, and over temperature conditions. All models are
RoHS compliant and have UL60950-1, EN60950-1, and IEC60950-1 safety approvals. This series is best
suited for use in wireless networks, telecom/datacom, industry control systems, measurement equipment,
and semiconductor equipment.
MODEL SELECTION TABLE
SINGLE OUTPUT MODELS
Output Current
Model Number Input Voltage Range
Output
Voltage
Min Load
Max Load
Output
Ripple & Noise
No Load
Input Current
Output
Power
Efficiency
Maximum
Capacitive Load
JFC12S33-30
3.3 VDC
0mA
7A
75mVp-p
12mA
23.1W
86%
10000µF
JFC12S05-30
5 VDC
0mA
6A
75mVp-p
12mA
30W
89%
7200µF
12 VDC
0mA
2.5A
75mVp-p
12mA
30W
89%
1200µF
JFC12S15-30
15 VDC
0mA
2A
75mVp-p
12mA
30W
89%
1000µF
JFC12S24-30
24 VDC
0mA
1.25A
75mVp-p
12mA
30W
90%
375µF
JFC24S33-30
3.3 VDC
0mA
7A
75mVp-p
10mA
23.1W
87%
10000µF
JFC24S05-30
5 VDC
0mA
6A
75mVp-p
10mA
30W
90%
7200µF
12 VDC
0mA
2.5A
75mVp-p
10mA
30W
91%
1200µF
JFC24S15-30
15 VDC
0mA
2A
75mVp-p
10mA
30W
91%
1000µF
JFC24S24-30
24 VDC
0mA
1.25A
75mVp-p
10mA
30W
93%
375µF
JFC48S33-30
3.3 VDC
0mA
7A
75mVp-p
8mA
23.1W
88%
10000µF
JFC12S12-30
JFC24S12-30
12 VDC
(9 - 18 VDC)
24 VDC
(18 - 36 VDC)
JFC48S05-30
5 VDC
0mA
6A
75mVp-p
8mA
30W
90%
7200µF
12 VDC
0mA
2.5A
75mVp-p
8mA
30W
90%
1200µF
JFC48S15-30
15 VDC
0mA
2A
75mVp-p
8mA
30W
91%
1000µF
JFC48S24-30
24 VDC
0mA
1.25A
75mVp-p
8mA
30W
92%
375µF
Output
Ripple & Noise
60mVp-p
No Load
Input Current
12mA
Output
Power
30W
JFC48S12-30
48 VDC
(36 - 75 VDC)
DUAL OUTPUT MODELS
89%
±15 VDC
0mA
±1.0A
60mVp-p
12mA
30W
90%
±500µF
JFC12D24-30
±24 VDC
0mA
±0.625A
75mVp-p
14mA
30W
89%
±180µF
JFC24D12-30
±12 VDC
0mA
±1.25A
60mVp-p
10mA
30W
91%
±750µF
±15 VDC
0mA
±1.0A
60mVp-p
10mA
30W
91%
±500µF
±180µF
JFC12D12-30
JFC12D15-30
JFC24D15-30
12 VDC
(9 - 18 VDC)
24 VDC
(18 - 36 VDC)
Output
Voltage
±12 VDC
Output Current
Min Load
Max Load
0mA
±1.25A
Maximum
Capacitive Load
±750µF
Model Number Input Voltage Range
Efficiency
JFC24D24-30
±24 VDC
0mA
±0.625A
75mVp-p
14mA
30W
90%
JFC48D12-30
±12 VDC
0mA
±1.25A
60mVp-p
8mA
30W
91%
±750µF
±15 VDC
0mA
±1.0A
60mVp-p
8mA
30W
92%
±500µF
±24 VDC
0mA
±0.625A
75mVp-p
10mA
30W
91%
±180µF
JFC48D15-30
JFC48D24-30
10/21/2013
48 VDC
(36 - 75 VDC)
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 •
Fax 603-778-9797
website: www.wallindustries.com • e-mail: [email protected]
Page 1 of 6
JFC30 SERIES
30 Watt DC/DC Power Converters
Rev B
SPECIFICATIONS: JFC30 SERIES
All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted.
We reserve the right to change specifications based on technological advances.
SPECIFICATION
TEST CONDITIONS
Min
Typ
Max
9
18
36
12
24
48
18
36
75
9
18
36
Unit
INPUT SPECIFICATIONS
Input Voltage Range
Start-Up Voltage
Shutdown Voltage
Input Surge Voltage (1sec, max.)
Input Reflected Ripple Current
Input Current
Input Filter
OUTPUT SPECIFICATIONS
Output Voltage
Voltage Accuracy
Line Regulation
12VDC nominal input models
24VDC nominal input models
48VDC nominal input models
12VDC nominal input models
24VDC nominal input models
48VDC nominal input models
12VDC nominal input models
24VDC nominal input models
48VDC nominal input models
12VDC nominal input models
24VDC nominal input models
48VDC nominal input models
No load to full load
Load Regulation
10% load to 90% load
Output Power
Output Current
Minimum Load
Maximum Capacitive Load
Ripple & Noise (20MHz BW)
Transient Response Recovery Time
Start-Up Time
Temperature Coefficient
PROTECTION
Short Circuit Protection
Over Load Protection
Over Voltage Protection
Over Temperature Protection
GENERAL SPECIFICATIONS
Efficiency
Switching Frequency
Single Output Models
30
See Table
Pi type
Single Output Models
Dual Output Models
Single Output Models
Dual Output Models
Single Output Models
Dual Output Models
15V & 24V Output Models
Others
0
Zener diode clamp
3.3V Output Models
5V Output Models
12V Output Models
15V Output Models
24V Output Models
Nominal input voltage and full load
3.3V & 5V Output Models
Others
1 minute
Isolation Resistance
Isolation Capacitance
500VDC
Input to Output
Input to Case
Output to Case
%
%
%
%
%
mVp-p
60
75
250
µs
30
30
+0.02
-0.02
% of rated full load at nominal input
%
%
See Table
75
75
75
3.3V & 5V Output Models
12V & 15V Output Models
24V Output Models
±12V & ±15V Output
With 10µF/25V X7R 1812 MLCC for each output
Models
With 6.8µF/50V X7R 1812 MLCC for each output ±24V Output Models
25% load step change
Power Up
Nom. input and constant resistive load
Remote ON/OFF
VDC
mAp-p
See Table
+1.0
+0.2
+0.5
+0.2
+1.0
+0.1
+0.8
+5.0
+20
+10
See Table
See Table
-1.0
-0.2
-0.5
-0.2
-1.0
-0.1
-0.8
-5.0
-10
-10
Minimum input and constant resistive load
With 22µF/25V X7R 1812 MLCC
With two 22µF/25V X7R 1812 MLCC
With two 6.8µF/50V X7R 1812 MLCC
Isolation Voltage
10/21/2013
VDC
25
50
100
Cross Regulation (Dual Output Models) Asymmetrical load 25% / 100% FL
Voltage Adjustability (See Note 1)
VDC
8
16
33
No Load
Low line to high line at full load
VDC
ms
%/°C
Hiccup, automatic recovery
140
%
3.7
5.4
5.6
7.0
13.5
19.6
VDC
18.3
22.0
29.1
32.5
+115
°C
247.5
297
1600
1000
1000
1
See Table
275
302.5
330
363
VDC
1500
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 •
Fax 603-778-9797
website: www.wallindustries.com • e-mail: [email protected]
kHz
GΩ
pF
Page 2 of 6
JFC30 SERIES
30 Watt DC/DC Power Converters
Rev B
SPECIFICATIONS: JFC30 SERIES
All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted.
We reserve the right to change specifications based on technological advances.
SPECIFICATION
TEST CONDITIONS
Min
Typ
Max
Unit
REMOTE ON/OFF (See Note 4)
Positive Logic (standard)
Referenced to –Input pin
Negative Logic (optional)
Referenced to –Input pin
DC/DC ON
DC/DC OFF
DC/DC ON
DC/DC OFF
Open or 3V < Vr < 15 VDC
Short or 0 < Vr < 1.2 VDC
Short or 0 <Vr < 1.2 VDC
Open or 3V < Vr < 15 VDC
-0.5
1.0
mA
2.0
mA
Without derating
With derating
-40
+50
Input Current of Remote Control Pin Nominal Vin
Remote OFF State Input Current
Nominal Vin
ENVIRONMENTAL SPECIFICATIONS
Operating Ambient Temperature
Vertical direction by natural convection (20LFM)
Maximum Case Temperature
Storage Temperature
Thermal Impedance (See Note 6)
-55
Without Heatsink
With Heatsink
Natural Convection (20LFM)
Relative Humidity
Thermal Shock
Vibration
15.0
13.8
5
BELLCORE TR-NWT-000332 Case 1: 50% Stress, Ta=40°C
MIL-HDBK-217F Ta=25°C, full load (G/B, controlled environment)
MTBF
+50
+100
+105
+125
PHYSICAL SPECIFICATIONS
Weight
Dimensions (L x W x H)
Case Material
Base Material
Potting Material
Shielding
SAFETY & EMC CHARACTERISTICS
Safety Approvals
EMI (See Note 2)
EN55022
ESD
EN61000-4-2
Radiated Immunity
Fast Transient (See Note 3)
Surge (See Note 3)
Conducted Immunity
EN61000-4-3
EN61000-4-4
EN61000-4-5
EN61000-4-6
°C
°C
°C
°C/W
95
MIL-STD-810F
MIL-STD-810F
1,579,000 hours
337,300 hours
% RH
0.58oz (16.5g)
1.00x1.00x0.39 inch (25.4x25.4x9.9 mm)
Copper
FR4 PCB
Silicon (UL94-V0)
Six-sided
IEC60950-1, UL60950-1, EN60950-1
Class B
Air ±8kV
Contact ±6kV
10 V/m
±2kV
±2kV
10 Vrms
Perf. Criteria A
Perf. Criteria A
Perf. Criteria A
Perf. Criteria A
Perf. Criteria A
NOTES
1. Trimming allows the user to increase or decrease the output voltage set point of the module. This is accomplished by connecting an
external resistor between the TRIM pin and either the +Vout pin or the –Vout pin.
2. The JFC30 series can only meet EMI Class A or Class B with external components added. See page 5 for more details.
3. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5.
- For 12VDC nominal input models we recommend connecting an aluminum electrolytic capacitor (Nippon chemi-con KY series,
220µF/100V)
and a TVS (SMDJ58A, 58V, 3000 Watt peak pulse power) diode in parallel.
- For 24VDC and 48VDC nominal input models we recommend an aluminum electrolytic capacitor (Nippon chemi-con KY series,
220µF/100V).
4. Both positive logic and negative logic remote ON/OFF control is available. Positive logic remote ON/OFF comes standard; for negative
logic
remote ON/OFF add the suffix “R” to the model number (Ex: JFC24S05-30R).
5. There are several different options available for this series. Please see the “Model Number Setup” on page 5 for all options and ordering
information.
6. Optional heatsink is available. Please call factory for more information.
CAUTION: This power module is not internally fused. An input line fuse must always be used.
Due to advances in technology, specifications subject to change without notice.
10/21/2013
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 •
Fax 603-778-9797
website: www.wallindustries.com • e-mail: [email protected]
Page 3 of 6
JFC30 SERIES
30 Watt DC/DC Power Converters
Rev B
DERATING CURVES
JFC24S05-30 Derating Curve
JFC24S05-30 Derating Curve with Heatsink
EFFICIENCY CURVES
JFC24S05-30 Efficiency vs Input Voltage
JFC24S05-30 Efficiency vs Output Load
MECHANICAL DRAWING
PIN
1
2
3
4
5
6
PIN CONNECTIONS
SINGLE
DUAL
+INPUT
+INPUT
-INPUT
-INPUT
CTRL
CTRL
+OUTPUT
+OUTPUT
TRIM
COMMON
-OUTPUT
-OUTPUT
PRODUCT OPTIONS
OPTION
Positive Logic
Negative Logic
Without CTRL Pin
Without CTRL and TRIM Pins
Positive Logic without TRIM Pin
Negative Logic without TRIM Pin
Heatsink
SUFFIX
None
R
D
G
F
RF
HC
EXTERNAL OUTPUT TRIMMING
NOTES
1. Unit: inches (mm)
2. Tolerance: X.XX±0.02 (X.X±0.5)
X.XXX±0.01 (X.XX±0.25)
3. Pin Pitch Tolerance: ±0.01 (±0.25)
4. Pin Dimension Tolerance: ±0.004 (±0.1)
5. All dimensions are for reference only
10/21/2013
Output can be externally trimmed by using
the method shown below
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 •
Fax 603-778-9797
website: www.wallindustries.com • e-mail: [email protected]
Page 4 of 6
JFC30 SERIES
30 Watt DC/DC Power Converters
Rev B
EMI CONSIDERATIONS
Recommended Filter for EN55022 Class A Compliance
Recommended Filter for EN55022 Class B Compliance
Model
Model
C1
L1
JFC12SXX-30
4.7µF/25V
1812 MLCC
JFC24SXX-30
4.7µF/50V
1812 MLCC
JFC48SXX-30
4.7µF/100V
1812 MLCC
JFC12SXX30
2.2µF
SMD Inductor
PMT-097
2.2µF
SMD Inductor
PMT-097
10µF
SMD Inductor
PMT-070
JFC24SXX30
JFC48SXX30
Recommended EN55022 Class A Filter Circuit Layout
C1
C2
C3
C4 & C5
L1
1000pF/2k
2.2µF
4.7µF/25V 4.7µF/25V 4.7µF/25V
V
1812
1812
SMD Inductor
1812
1206
MLCC
MLCC
PMT-097
MLCC
MLCC
1000pF/2k
2.2µF
4.7µF/50V 4.7µF/50V 4.7µF/50V
V
1812
1812
SMD Inductor
1812
1206
MLCC
MLCC
PMT-097
MLCC
MLCC
4.7µF/100 4.7µF/100 4.7µF/100 2200pF/2k
10µF
V
V
V
V
SMD Inductor
1812
1812
1812
1206
PMT-070
MLCC
MLCC
MLCC
MLCC
Recommended EN55022 Class B Filter Circuit Layout
MODEL NUMBER SETUP
JFC
24
S
05
30
R
H
Series Name
Input Voltage
Output Quantity
Ouptut Voltage
Output Power
Remote ON/OFF, CTRL, and TRIM Pins
Heatsink
Single
Output
33: 3.3 VDC
30: 30 Watts
12: 9-18 VDC
S:
-
None: Positive Logic
24: 18-36 VDC
05: 5 VDC
R: Negative Logic
48: 36-75 VDC
12: 12 VDC
D: Without CTRL Pin
15: 15 VDC
24: 24 VDC
D: Dual Output
12: ±12 VDC
None
No Heatsink
:
HC: Heatsink
G: Without CTRL and TRIM Pins
Positive Logic without TRIM
F:
Pin
Negative Logic without TRIM
RF:
Pin
15: ±15 VDC
24: ±24 VDC
10/21/2013
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 •
Fax 603-778-9797
website: www.wallindustries.com • e-mail: [email protected]
Page 5 of 6
Rev B
JFC30 SERIES
30 Watt DC/DC Power Converters
COMPANY INFORMATION
Wall Industries, Inc. has created custom and modified units for over 50 years. Our in-house research and development
engineers will provide a solution that exceeds your performance requirements on-time and on budget. Our ISO9001-2008
certification is just one example of our commitment to producing a high quality, well-documented product for our customers.
Our past projects demonstrate our commitment to you, our customer. Wall Industries, Inc. has a reputation for working closely
with its customers to ensure each solution meets or exceeds form, fit and function requirements. We will continue to provide
ongoing support for your project above and beyond the design and production phases. Give us a call today to discuss your
future projects.
Contact Wall Industries for further information:
Phone:
Toll Free:
Fax:
E-mail:
Web:
Address:
10/21/2013
(603)778-2300
(888)597-9255
(603)778-9797
[email protected]
www.wallindustries.com
37 Industrial Drive
Exeter, NH 03833
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 •
Fax 603-778-9797
website: www.wallindustries.com • e-mail: [email protected]
Page 6 of 6
Similar pages