HER1001G - HER1008G 10.0 AMPS. Glass Passivated High Efficient Rectifiers TO-220AB Features Glass passivated chip junction. High efficiency, Low VF High current capability High reliability High surge current capability For use in low voltage, high frequency inventor, free wheeling, and polarity protection application. Mechanical Data Case: TO-220AB molded plastic Epoxy: UL 94V0 rate flame retardant Terminals: Pure tin plated, lead free, solderable per MIL-STD-202, Method 208 guaranteed Polarity: As marked High temperature soldering guaranteed: 260 oC/10 seconds .16”,(4.06mm) from case. Weight: 2.24 grams Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics o Rating at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Symbol Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current o @T C = 100 C Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 5.0A Maximum DC Reverse Current o @ T A=25 C at Rated DC Blocking Voltage @ T A=125 oC Maximum Reverse Recovery Time ( Note 1) Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance (Note 3) Operating Temperature Range V RRM V RMS V DC HER HER HER HER HER HER HER HER 1001G 1002G 1003G 1004G 1005G 1006G 1007G 1008G 50 35 50 100 70 100 200 140 200 300 210 300 400 280 400 600 420 600 800 1000 560 700 800 1000 Units V V V I(AV) 10 A IFSM 125 A VF 1.0 1.3 10 400 IR Trr Cj R θJC TJ 1.7 50 60 80 40 1.5 -65 to +150 -65 to +150 Storage Temperature Range TSTG 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A Notes: 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 3. Mounted on Heatsink Size of 2” x 3 “ x 0.25” Al-Plate. V uA uA nS pF o C/W o C o C Version: A06 RATINGS AND CHARACTERISTIC CURVES (HER1001G THRU HER1008G) FIG.2- TYPICAL REVERSE CHARACTERISTICS 1000 10 6 4 2 0 0 100 50 150 o FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 150 125 Tj=75 0C 10 1 Tj=25 0C 0.1 0 8.3ms Single Half Sine Wave JEDEC Method 100 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 75 FIG.5- TYPICAL FORWARD CHARACTERISTICS 100 50 25 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE 240 200 CAPACITANCE.(pF) Tj=125 0C 100 160 120 HE R1 00 1G 80 ~H HE ER 10 R1 40 05 00 6G ~ HE R1 00 0 1 2 5 G 10 HE 3 20 50 100 200 500 1000 5G 00 R1 G 08 10 ER H ~ 6G 00 R1 HE 1 0.3 0.1 0 0.03 8G 10 30 HE R1 00 1G ~H ER 10 04 G PEAK FORWARD SURGE CURRENT. (A) LEAD TEMPERATURE. ( C) INSTANTANEOUS REVERSE CURRENT. ( A) 8 INSTANTANEOUS FORWARD CURRENT. (A) AVERAGE FORWARD CURRENT. (A) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 0.01 0.4 Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 0.6 0.8 1.0 1.2 1.4 1.6 1.8 FORWARD VOLTAGE. (V) REVERSE VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (+) 50Vdc (approx) (-) (-) DUT PULSE GENERATOR (NOTE 2) NON INDUCTIVE OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: A06