CXO3MHG OSCILLATOR 200 kHz to 200 MHz High Shock, Low-Profile Miniature Surface-Mount 3.3 V Crystal Oscillator DESCRIPTION Intended for applications requiring shock survivability to 10,000 g (and higher), Statek’s surface-mount CXO3MHG oscillators are high-shock versions of the CXO3M oscillators. These oscillators consist of a Statek miniature quartz crystal and a CMOS/TTL compatible hybrid circuit in a low-profile ceramic package with an extremely small footprint. FEATURES High shock resistance 3.3 V operation Designed for surface mount applications using infrared, vapor phase, or epoxy mount techniques CMOS and TTL compatible DIMENSIONS Low power consumption D Optional Output Enable/Disable with Tri-State 2 Low EMI emission A Full military testing available TOP 3 BOTTOM 1 APPLICATIONS 4 D Military & Aerospace B Smart munitions E C Projectile electronics Industrial TYPICAL Engine control Down-hole drilling SUGGESTED LAND PATTERN MAXIMUM DIM inches mm inches mm A 0.256 6.50 0.263 6.68 B 0.197 5.00 0.204 5.18 0.051 C (SM1) C (SM3/SM5) 0.055 1.30 1.40 0.055 0.063 1.40 1.60 D 0.055 1.40 0.065 1.65 E 0.060 1.52 0.070 1.78 0.070 (1.78) 0.067 (1.70) 0.065 (1.65) PIN CONNECTIONS 1. Enable/Disable (E or T) or not connected (N) 2. Ground 0.201 (5.11) 0.136 (3.45) 3. Output 4. VDD GRID PLACEMENT COURTYARD 10172 Rev. C IS O STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com YS 90 01 TEM C ERT I F I C AT N IO S 0.137 (3.48) ABSOLUTE MAXIMUM RATINGS SPECIFICATIONS Specifications are typical at 25 C unless otherwise noted. Specifications are subject to change without notice. Tighter specifications available. Please contact factory. O Supply Voltage1 3.3 V Calibration Tolerance2 + _ Frequency Stability Over Temperature3 + _ + _ *The supply voltage range is -0.5 V to +4.0 V for some products. Contact Factory. 10% 100 ppm ENABLE/DISABLE OPTIONS (E/T/N) 50 ppm for Commercial + _ 100 ppm for Industrial + _ 100 ppm for Military 10 MHz 2 mA 24 MHz 4 mA 30 MHz 6 mA 40 MHz 8 mA 50 MHz 10 mA Supply Current (Typical) Output Load (CMOS)4 15 pF Start-up Time Rise/Fall Time 5 ms MAX 6 ns MAX Duty Cycle 40% MIN, 60% MAX Aging, first year 10 ppm MAX Shock, survival 10,000 g, 0.3 ms, 1/2 sine Vibration, survival6 20 g, 10-2,000 Hz swept sine 5 Supply Voltage VDD -0.5 V to 7.0 V Storage Temperature -55OC to +125OC Maximum Process Temperature 260OC for 20 seconds Statek offers three enable/disable options: E, T, and N. Both the E-version and T-version have Tri-State outputs and differ in whether the oscillator continues to run internally when the output is put into the high Z state: it stops in the E-version and continues to run in the T-version. So, the Eversion offers very low current consumption when the oscillator is disabled and the T-version offers very fast output recovery when the oscillator is re-enabled. The N-version does not have PIN 1 connected internally and so has no enable/disable capability. The following table summarizes the three options. COMPARISON OF ENABLE/DISABLE OPTIONS E AND T E T When enabled (PIN 1 is high*) Operating Temp Ranges -10OC to +70OC (Commercial) -40OC to +85OC (Industrial) -55OC to +125OC (Military) 1. Other voltages available. For 5.0 V, see CXOMHG data sheet. For others, contact factory. 2. Other tolerances available. 3. Does not include calibration tolerance. Other tolerances available. 4. Higher CMOS loads and TTL loads available. Contact factory. 5. Higher shock version available. Contact factory for requirements above 10,000 g. 6. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also available. Note: All parameters are measured at ambient temperature with a 10 MΩ, 15 pF load. Output Freq. output Freq. output Oscillator Oscillates Oscillates Current consumption Normal Normal Output High Z state High Z state Oscillator Stops Oscillates Current consumption Very low Lower than normal When disabled (PIN 1 is low) When re-enabled (PIN 1 changes from low to high) PACKAGING OPTIONS Output recovery CXO3MHG - Tray Pack - 16 mm tape, 7˝ or 13˝ reels Per EIA 418 (see Tape and Reel data sheet 10109) Delayed Immediate * When PIN 1 is allowed to float, it is held high by an internal pull-up resistor. HOW TO ORDER CXO3MHG SURFACE MOUNT CRYSTAL OSCILLATORS CXO3MHG S “S” if special or custom design; otherwise blank. N Enable/Disable Option E, T*, or N SM3 Terminations Blank = SM1 = Gold Plated SM3 = Solder Dipped SM5 = Solder Dipped (Lead Free) 32.0M , Frequency K = kHz M = MHz 100 / 100 / Frequency Stability over Temp.Range (in ppm) Calibration Tolerance @ 250C (in ppm) I / Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified OR / 200 Total Frequency Tolerance (in ppm) / I Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified 10172 Rev C IS O STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com YS 90 01 TEM C ERT I F I C AT N IO S *The T-version is not available for all frequencies. Contact factory. /