MPL-05SE Series Single Output, 5W Ultra-Miniature SIP AC/DC Power Supplies Key Features: Electrical Specifications • 5W Output Power • Universal 85-264 VAC Input • EN 60950 Approved (UL) • Meets IEC Safety Class II • Single Regulated Output • Meets EN 55022 Class A • >300 kHour MTBF • Ultra-Miniature “SIP” Case Specifications typical @ +25°C, 230 VAC input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Parameter Conditions Min. 85 100 47 Input Voltage Range Input Frequency Typ. 115 VAC 230 VAC 115 VAC 230 VAC Input Current Inrush Current Max. 264 400 63 0.15 0.20 20.0 30.0 Leakage Current Units VAC VDC Hz A A Pk 5.0 mA Conditions Min. Typ. See Model Selection Guide See Model Selection Guide See Model Selection Guide VIN = Min to Max ±0.5 IOUT = 10% to 100% ±1.5 3.3V, 24V Models 50 All Other Models 50 115 VAC 20 230 VAC 80 ±0.15 Continuous (Autorecovery) Max. Units Conditions Input to Output Max. Output Parameter Output Voltage Output Current Output Voltage Accuracy Line Regulation Load Regulation Ripple & Noise (20 MHz) Hold-Up Time Temperature Coefficient Short Circuit Protection % % 150 120 mV P-P mSec %/°C General Parameter Isolation Voltage Switching Frequency EMI Characteristics Parameter Radiated Emissions Conducted Emissions ESD RS EFT Surge CS PFMF Voltage Dips Min. 3,000 Typ. 100 Standard See Note 2 EN 55022 See Note 2 EN 55022 EN 61000-4-2 EN 61000-4-3 See Note 3 EN 61000-4-4 See Note 4 EN 61000-4-5 EN 61000-4-6 EN 61000-4-8 EN 61000-4-11 Min. Units VAC kHz Typ. Max. Units Class A Class A Criteria B; ±4 kV Contact Criteria A; 10V/m Criteria B; ±2 kV Criteria B; ±2 kV /±4 kV Criteria A; 3 Vrms Criteria A; 10A/m Criteria B; 0% - 70% Environmental MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity Conditions Max. +85 +100 -40 +105 Free Air Convection (See Derating Curve) RH, Non-condensing 85 Ambient Case Min. -25 Typ. +25 Units °C °C °C % Physical Case Size Case Material Weight 1.65 x 0.43 x 1.06 Inches (42.0 x 11.0 x 27.0 mm) Non-Conductive Epoxy (UL94-V0) 0.35 Oz (10g) Reliability Specifications Parameter MTBF Safety Standards Safety Class Conditions Min. Typ. MIL HDBK 217F, 25°C, Gnd Benign 300 EN 60950 IEC 61140 Class II www.micropowerdirect.com Max. Units kHours www.micropowerdirect.com Model Selection Guide Output Model Number Voltage Current (VDC) (mA Max.) MPL-05S-03E MPL-05S-05E MPL-05S-09E MPL-05S-12E MPL-05S-15E MPL-05S-24E 3.3 5.0 9.0 12.0 15.0 24.0 1,000 1,000 560 420 340 210 Typical Connection Output Max Voltage Capacitive Efficiency Accuracy (%, Typ) Load (%) (µF) ±2.0 ±1.0 ±1.0 ±1.0 ±1.0 ±1.0 1,000 1,500 630 470 330 100 65 70 72 74 75 75 Notes: 1. Operation at no load will not damage the units, however, they may not meet all specifications. 2. All units are rated for EN 55022 (CE/RE) class A with the addition of external components such as the typical circuit shown below. They will meet class B with the addition of the ACFM-01 (or a similar discrete filter circuit). Contact the factory for more information. 3. To meet the requirements of EN 61000-4-4 (±4 kV), external components are needed. This can be done discretely, or with the addition of the ACFM-01. Contact the factory for more information. 4. To meet the requirements of EN 61000-4-5 (±4 kV/±4 kV), external components are needed. This can be done discretely, or with the addition of the ACFM-01. Contact the factory for more information. 5. It is recommended that a fuse be used on the input of a power supply for protection. For the MPL-05SE series, a 1.0A/250 VAC slow blow should be used. The diagram below illustrates a typical application connection of the MPL-05SE series. Notes on this circuit (starting with the input circuit) are: 1. It is recommended that an external fuse and NTC be used. The recommended fuse is a 1.0A/250V slow blow and for the NTC, a 5D-9. 2. An external MOV is recommended on the input to protect the unit in the event of a surge. A 561KD14 or equivalent is recommended. 3. The filter capacitor C1 is required for specified operation. The recommended value is 33 µF/400V. 4. The safety capacitors (Cx1 and CY0) provide EMI/RFI suppresion. Recommended values are 0.22 µF/275 VAC (Cx1) and 1 nF/400 VAC (CY0). 5. Recommended values for other components are: Output 3.3V 5.0V 9.0V 12V 15V 24V Typical Board Layout: With ACFM-01 Input Module (See note 6) L1 0.47 µH 0.47 µH 1.0 µH 1.0 µH 1.0 µH 4.7 µH C2 470 µF/16V 470 µF/16V 330 µF/35V 330 µF/35V 330 µF/35V 100 µF/35V C3 C4 TVS 150 µF/35V 100 nF/50V SMBJ7.0A 150 µF/35V 100 nF/50V SMBJ7.0A 150 µF/35V 100 nF/50V SMBJ12A 150 µF/35V 100 nF/50V SMBJ20A 150 µF/35V 100 nF/50V SMBJ20A 47 µF/35V 100 nF/50V SMBJ30A The output filtering capacitors (C2,C3) are high frequency, low resistance electrolytic capacitors. Capacitor (C4) is ceramic. Voltage derating of capacitors should be 80% or above. 6. Input noise and surge suppression modules are available for a number of MPD AC/DC power supplies. An MPL-05SE connection with the ACFM-01 is illustrated in the diagram at left. For pricing or full technical information on these modules (ACFM-01 and ACFM-02) please contact the factory. Pin Connections Derating Curve Pin Function Pin Function 1 3 5 AC-Neutral AC-Line +VCAP 7 12 14 -VCAP -VOUT +VOUT Mechanical Dimensions Input Voltage Vs Load MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.02 (±0.50) FAX: (781) 344-8481 • E-Mail: [email protected]