MRV EM1600-OAI Lambdadriver optical amplifi er module (em800-oax/em1600-oax) Datasheet

WDM & Optical Transport
Datasheet
LambdaDriver® - Optical Amplifier Module (EM800-OAx/EM1600-OAx)
Features
Booster, In line and Pre-Amplifier
Up to 22dBm maximum output power
Protocol and bandwidth transparent
Gain flatness (with GFF) less than 1.0 dB
Low Noise figure
Optical power monitoring
Front panel status LEDs
Fast transient suppression time
Automatic Laser Shutdown (ALS)
Applications
DWDM networks
Single-channel amplification
Distance extention
Optical Amplifier modules
LambdaDriver® Optical Amplifier modules are a family
of low-noise Erbium-Doped Fiber Amplifiers (EDFA) ideal
for Metro and Long-Haul Dense Wavelength Division
Multiplexing (DWDM) as well as Single Wavelength
applications. The optical design, coupled with sophisticated
control circuitry, allows these Optical Amplifiers to provide
constant gain even with wavelengths being added or
dropped in the network. Any fluctuations caused by
wavelengths addition/removal can be handled by its ultrafast transient suppression.
When paired with the LambdaDriver® Element
Management Module , full monitoring and configuration
capabilities are supported with a local RS-232 interface
and Ethernet/Fast Ethernet interfaces for remote network
monitoring using Telnet and SNMP.
Using MRV’s MegaVision Web® NMS provides remote
control reducing the costly need for many infield service
calls.
The modules allow monitoring of input and output power
levels (real dBm values), temperature and signal gain.
The modules can be operated in two modes: automatic
gain control or automatic power control. These operating
modes and their respective parameter settings are factory
pre-configured but can be changed by MRV authorized
personnel.
In AGC mode, the module maintains constant gain for
each channel according to the Gain parameter setting,
as long as the total output power does not exceed the
maximum rated value (+22 dBm). This mode is factory preconfigured.
�����
�����
�����
�����������
�����������
�����������
����
���
�����
�������
���
���
�� ����
�� ��
����� ����
���
�����������
�� ��
�����������
�����������
������� ���������
������� ���������
Long Haul Application
������� ���������
Not sure what solution best fits your needs? Visit www.mrv.com or e-mail us at [email protected]
WDM & Optical Transport
In APC mode, the module maintains the output total
power constant at the pre-defined Output Power
settings.
Additionaly a special OA module, EM800-OAPD, includes
an integrated Tunable Optical Dispersion Compensator
(TODC). Tuning of dispersion is done via the system
management module.
There are 3 types of OAs: Booster, In-Line and PreAmplifier. The main difference between these modules
is the Input power level that dictates the application of
the specific module and the Gain values. For example,
Booster is usually used at the beginning of the line and
therefore Input levels above 0 dBm and Gain of 9 to15
dB should be expected. On the other hand, Pre-Amplifier
Input level is very weak (down to –32 dBm/channel)
because it is positioned at the end of the line.
Multi-channel (DWDM) amplifiers are equipped with
Gain Flattening Filters (GFF) and provide flat gain
response across entire C-band and input power range.
For single channel applications GFF cost is saved.
Optical Amplifier modules provide Automatic Power
Shutdown, when input is below auto-shutdown
threshold. Power Shutdown can be also forced through
the management.
The compact, 1-slot LambdaDriver Optical Amplifier
modules install into any of the LambdaDriver® chassis.
Most of the standard EDFA units have maximum
+18dBm total output power. Special “High Power” EDFA
modules have maximum +22dBm total output power
that mainly serve high wavelength count (more than
32 waves) DWDM or ultra long single span applications.
These high power units are double slot size.
Each module provides visual indications of the front
panel and can be operated without management as
plug and play EDFA.
Besides DWDM networks application, LambdaDriver®
EDFAs can be used in any Single channel application
thus providing flexible means of extending an optical
link by compensating for optical budget loss.
WDM & Optical Transport
Environment Specifications
Operating Temperature
Storage Temperature
Relative Humidity
Dimensions (W x H x D)
Weight:
EM800 + 18dBm type
EM1600 + 18dBm type
EM800 High Power
EM1600 High Power
EM800 + 18dBm type
EM1600 + 18dBm type
EM800 High Power
EM1600 High Power
Connectors
- All
- High Power Ouput
-5 oC - 45 oC
-10 oC - 70 oC
85% maximum, non-condensing
26.93 mm (1.06 in)
26.93 mm (1.06 in)
54.18 mm (2.13 in)
54.18 mm (1.06 in)
0.586 Kg (1.28Lb)
0.865 Kg (2.11Lb)
1.016 Kg (2.24Lb)
1.305 Kg (2.47Lb)
x
x
x
x
130.7 mm (5.145 in) x 227 mm (8.956 in) (1 slot wide)
263.4 mm (10.37 in) x 227 mm (8.956 in) (1 slot wide)
130.7 mm (5.14 in) x 227 mm (8.956 in) (2 slot wide)
263.4 mm (10.37 in) x 227 mm (8.956 in) (2 slot wide)
SC
E2000APC
Technical Specifications
Parameter
Wavelength Range
Maximum Output power
Booster & In-Line
With Mid-Stage
SOAB13, SOAI & Pre-Amplifier
High Power Booster
High Power In-line
Minimum Input power
Booster
In-Line
Pre-Amplifier
Input Dynamic Range
Input/Output Isolation (Min)
Signal Gain *
Booster
In-line
Pre-amp
Gain Flatness at Specified Gain with GFF
Signal- Noise Figure for Gain > 20 dB
Optical Return Loss (at Input and Output ports)
Polarization Mode Dispersion
Polariziation Dependent Gain
Transient Overshoot (10 dB Drop)
Transient Suppression Time (10 dB Drop)
Minimum
1528
Value
Typical
Maximum
1563
+18
+17
+13
+22
+21
-15
-25
-30
Units
nm
dBm
dBm
25
dB
dB
30
9 or 15
20 or 25
10 or 20
+/-0.5
5.0
dB
+/-1.0
5.5
25
0.3
+/-0.2
0.5
0.5
+/-0.5
1.0
< 32
dB
dB
dB
dB
dB
dB
µs
Management
Tunable dispersion range (EM800/EM1600 - OAPD
EM800/EM1600 - OABD, EM800/EM1600 - OAID)
-1700ps/nm to +1700ps/nm
WDM transmission laser status, Temperature status, Port
reception status, Port transmission status
Input power, Output power, Gain, Temperature
Input power, Output power, Temperature
LEDs
Monitoring
Alarm
Power Consumption:
18dBm type
High Power
* Model dependent - see ordering information section
3.3 W
15 W
Ordering Information
WDM & Optical Transport
EM800-OAIM
Optical In Line Amplifier with Mid-stage +17dbm output and 20db gain
EM800-OAIM25
Optical In Line Amplifier with Mid stage +17dbm output and 25db gain
EM800-OAI
Optical In Line Amplifier + 18dbm output and 20db gain
EM800-OAP
Optical Pre-Amplifier + 13dbm output and 20db gain
EM800-OAP10
Optical Pre-Amplifier +13 dbm output and 10db gain
EM800-OAB
Optical Booster Amplifier + 18dbm output and 9db gain
EM800-OABM
Optical Booster Amplifier with Mid-stage +17dbm output and 9db gain
EM800-SOAIM
Single channel Optical in line Amplifier with Mid-stage +13dbm output and 20db gain
EM800-SOAI
Single channel Optical in line Amplifier output +13dbm output and 20db gain
EM800-SOAI25
Single channel Optical in line Amplifier output +17dbm output and 25db gain
EM800-OAI25
Optical In Line Amplifier +18dbm output and 25db gain
EM800-SOAP
Single channel Optical Pre - Amplifier +13dbm output and 20db gain
EM800-SOAB
Single channel Optical Booster Amplifier +18dbm output and 15db gain
EM800-SOAB13
Single channel Optical Booster Amplifier +13dbm output and 15db gain
EM1600-OABM
Optical Booster Amplifier with Mid-stage +17dbm output and 9db gain
EM1600-OAIM
Optical In Line Amplifier with Mid-stage +17dbm output and 20db gain
EM1600-OAI
Optical In Line Amplifier +18 dbm output and 20db gain
EM1600-OAP
Optical Pre-Amplifier +13 dbm output and 20db gain
EM1600-OAP10
Optical Pre-Amplifier +13 dbm output and 10db gain
EM1600-OAB
Optical Booster Amplifier +18 dbm output and 9db gain
EM1600-SOAIM
Single channel Optical in line Amplifier with Mid-stage + 13dbm output and 20db gain
EM1600-SOAI
Single channel Optical in line Amplifier + 13dbm output and 20db gain
EM1600-SOAP
Single channel Optical Pre-Amplifier + 13dbm output and 20db gain
EM1600-SOAB
Single channel Optical Booster Amplifier + 18dbm output and 15db gain
EM1600-SOAB13
Single channel Optical Booster Amplifier + 13dbm output and 15db gain
High Power EDFAs
EM800-OAI21P
Optical In Line Amplifier with +21dbm output and 20db gain
EM800-OAI21PM
Optical In Line Amplifier with Mid-stage +21dbm output and 20db gain
EM800-OAI21PM25
Optical In Line Amplifier with Mid-stage +21dbm output and 25db gain
EM800-OAB22P
Optical Booster Amplifier with +22dbm output and 9db gain
EM800-OAB22PM
Optical Booster with Mid-stage+22dbm output and 9db gain
EM800-SOAB22P
Single channel Optical Booster Amplifier +22dbm output and 20db gain
EM1600-OAB22P
Optical Booster Amplifier with +22dbm output and 9db gain
EM1600-OAB22PM
Optical Booster Amplifier with Mid-stage +22dbm output and 9db gain
EM1600-OAI21P
Optical In Line Amplifier with +21dbm output and 20db gain
EM1600-OAI21PM
Optical In Line Amplifier with Mid-stage +21dbm output and 20db gain
EM1600-SOAB22P
Single channel Optical Booster Amplifier + 22dbm output and 20dB gain
EDFAs with Integrated TDC
EM800-OAPD
Optical Pre-Amplifier with integrated DC +13dbm output and 20db gain
EM800-OABD
Optical Booster Amplifier with integrated DC +18dbm output and 9db gain
EM800-OAID
Optical In Line Amplifier with integrated DC +18dbm output and 20db gain
EM800-OAI25D
Optical In Line Amplifier with integrated DC +17dbm output and 25db gain
EM1600-OAPD
Optical Pre-Amplifier with integrated DC +13dbm output and 20db gain
EM1600-OABD
Optical Booster Amplifier with integrated DC +18 dbm output and 9db gain
EM1600-OAID
Optical In Line Amplifier with integrated DC +18 dbm output and 20db gain
EM1600-OAP10D
Optical Pre-Amplifier with integrated DC +13dbm output and 10db gain
MRV-LD-OA
Rev.4 11-08
Copyright ©2008 MRV Communications, Inc. All Rights Reserved.
Similar pages