ON LM2904N Single supply dual operational amplifier Datasheet

LM358, LM258, LM2904,
LM2904A, LM2904V,
NCV2904
Single Supply Dual
Operational Amplifiers
Utilizing the circuit designs perfected for Quad Operational
Amplifiers, these dual operational amplifiers feature low power drain,
a common mode input voltage range extending to ground/VEE, and
single supply or split supply operation. The LM358 series is
equivalent to one−half of an LM324.
These amplifiers have several distinct advantages over standard
operational amplifier types in single supply applications. They can
operate at supply voltages as low as 3.0 V or as high as 32 V, with
quiescent currents about one−fifth of those associated with the
MC1741 (on a per amplifier basis). The common mode input range
includes the negative supply, thereby eliminating the necessity for
external biasing components in many applications. The output voltage
range also includes the negative power supply voltage.
Features
•
•
•
•
•
•
•
•
•
•
http://onsemi.com
PDIP−8
N, AN, VN SUFFIX
CASE 626
8
1
SOIC−8
D, VD SUFFIX
CASE 751
8
1
Micro8
DMR2 SUFFIX
CASE 846A
8
Short Circuit Protected Outputs
True Differential Input Stage
Single Supply Operation: 3.0 V to 32 V
Low Input Bias Currents
Internally Compensated
Common Mode Range Extends to Negative Supply
Single and Split Supply Operation
ESD Clamps on the Inputs Increase Ruggedness of the Device
without Affecting Operation
Pb−Free Packages are Available
NCV Prefix for Automotive and Other Applications Requiring Site
and Control Changes
1
PIN CONNECTIONS
Output A
Inputs A
VEE/Gnd
1
8
2
7
4
−
+ 5
−
+
3
VCC
Output B
6
Inputs B
(Top View)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 10 of this data sheet.
DEVICE MARKING INFORMATION
See general marking information in the device marking
section on page 11 of this data sheet.
 Semiconductor Components Industries, LLC, 2004
July, 2004 − Rev. 18
1
Publication Order Number:
LM358/D
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
3.0 V to VCC(max)
VCC
VCC
1
1
2
2
1.5 V to VCC(max)
1.5 V to VEE(max)
VEE
VEE/Gnd
Single Supply
Split Supplies
Figure 1.
Output
Bias Circuitry
Common to Both
Amplifiers
VCC
Q15
Q16
Q22
Q14
Q13
40 k
Q19
5.0 pF
Q12
Q24
25
Q23
Q20
Q18
Inputs
Q11
Q9
Q21
Q17
Q6
Q2
Q25
Q7
Q5
Q1
Q8
Q3
Q4
Q10
Q26
2.4 k
2.0 k
VEE/Gnd
Figure 2. Representative Schematic Diagram
(One−Half of Circuit Shown)
http://onsemi.com
2
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
MAXIMUM RATINGS (TA = +25°C, unless otherwise noted.)
Symbol
Value
VCC
VCC, VEE
32
±16
Input Differential Voltage Range (Note 1)
VIDR
±32
Vdc
Input Common Mode Voltage Range (Note 2)
VICR
−0.3 to 32
Vdc
Output Short Circuit Duration
tSC
Continuous
Junction Temperature
TJ
150
°C
RJA
238
°C/W
Storage Temperature Range
Tstg
−55 to +125
°C
ESD Protection at any Pin
Human Body Model
Machine Model
Vesd
Rating
Power Supply Voltages
Single Supply
Split Supplies
Unit
Vdc
Thermal Resistance, Junction−to−Air (Note 3)
V
2000
200
Operating Ambient Temperature Range
°C
TA
LM258
LM358
LM2904/LM2904A
LM2904V, NCV2904 (Note 4)
−25 to +85
0 to +70
−40 to +105
−40 to +125
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
1. Split Power Supplies.
2. For Supply Voltages less than 32 V the absolute maximum input voltage is equal to the supply voltage.
3. RJA for Case 846A.
4. NCV2904 is qualified for automotive use.
http://onsemi.com
3
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = GND, TA = 25°C, unless otherwise noted.)
LM258
Characteristic
Input Offset Voltage
VCC = 5.0 V to 30 V, VIC = 0 V to VCC −1.7 V,
VO 1.4 V, RS = 0 TA = 25°C
TA = Thigh (Note 5)
TA = Tlow (Note 5)
Min
Symbol
Typ
LM358
Max
Min
Typ
Max
VIO
Unit
mV
−
−
−
2.0
−
−
5.0
7.0
7.0
−
−
−
2.0
−
−
7.0
9.0
9.0
VIO/T
−
7.0
−
−
7.0
−
V/°C
IIO
−
−
−
−
3.0
−
−45
−50
30
100
−150
−300
−
−
−
−
5.0
−
−45
−50
50
150
−250
−500
nA
IIO/T
−
10
−
−
10
−
pA/°C
Input Common Mode Voltage Range (Note 6),
VCC = 30 V
VCC = 30 V, TA = Thigh to Tlow
VICR
0
−
28.3
0
−
28.3
V
0
−
28
0
−
28
Differential Input Voltage Range
VIDR
−
−
VCC
−
−
VCC
Large Signal Open Loop Voltage Gain
RL = 2.0 k, VCC = 15 V, For Large VO Swing,
TA = Thigh to Tlow (Note 5)
AVOL
50
25
100
−
−
−
25
15
100
−
−
−
CS
−
−120
−
−
−120
−
dB
Common Mode Rejection
RS ≤ 10 k
CMR
70
85
−
65
70
−
dB
Power Supply Rejection
PSR
65
100
−
65
100
−
dB
Output Voltage−High Limit
TA = Thigh to Tlow (Note 5)
VCC = 5.0 V, RL = 2.0 k, TA = 25°C
VCC = 30 V, RL = 2.0 k
VCC = 30 V, RL = 10 k
VOH
Output Voltage−Low Limit
VCC = 5.0 V, RL = 10 k,
TA = Thigh to Tlow (Note 5)
Average Temperature Coefficient of Input Offset
Voltage
TA = Thigh to Tlow (Note 5)
Input Offset Current
TA = Thigh to Tlow (Note 5)
Input Bias Current
TA = Thigh to Tlow (Note 5)
Average Temperature Coefficient of Input Offset
Current
TA = Thigh to Tlow (Note 5)
Channel Separation
1.0 kHz ≤ f ≤ 20 kHz, Input Referenced
IIB
V
V/mV
V
3.3
26
27
3.5
−
28
−
−
−
3.3
26
27
3.5
−
28
−
−
−
VOL
−
5.0
20
−
5.0
20
mV
Output Source Current
VID = +1.0 V, VCC = 15 V
IO+
20
40
−
20
40
−
mA
Output Sink Current
VID = −1.0 V, VCC = 15 V
VID = −1.0 V, VO = 200 mV
IO−
10
12
20
50
−
−
10
12
20
50
−
−
mA
A
Output Short Circuit to Ground (Note 7)
ISC
−
40
60
−
40
60
mA
Power Supply Current (Total Device)
TA = Thigh to Tlow (Note 5)
VCC = 30 V, VO = 0 V, RL = ∞
VCC = 5 V, VO = 0 V, RL = ∞
ICC
mA
−
−
1.5
0.7
3.0
1.2
−
−
1.5
0.7
3.0
1.2
5. LM258: Tlow = −25°C, Thigh = +85°C
LM358: Tlow = 0°C, Thigh = +70°C
LM2904/LM2904A: Tlow = −40°C, Thigh = +105°C
LM2904V & NCV2904: Tlow = −40°C, Thigh = +125°C
NCV2904 is qualified for automotive use.
6. The input common mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of
the common mode voltage range is VCC − 1.7 V.
7. Short circuits from the output to VCC can cause excessive heating and eventual destruction. Destructive dissipation can result from
simultaneous shorts on all amplifiers.
http://onsemi.com
4
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = Gnd, TA = 25°C, unless otherwise noted.)
LM2904
Characteristic
Input Offset Voltage
VCC = 5.0 V to 30 V, VIC = 0 V to VCC −1.7 V,
VO 1.4 V, RS = 0 TA = 25°C
TA = Thigh (Note 8)
TA = Tlow (Note 8)
Symbol
Min
Typ
LM2904A
Max
Min
Typ
LM2904V, NCV2904
Max
Min
Typ
Max
VIO
Unit
mV
−
−
−
2.0
−
−
7.0
10
10
−
−
−
2.0
−
−
7.0
10
10
−
−
−
−
−
−
7.0
13
10
VIO/T
−
7.0
−
−
7.0
−
−
7.0
−
V/°C
IIO
−
−
−
−
5.0
45
−45
−50
50
200
−250
−500
−
−
−
−
5.0
45
−45
−50
50
200
−100
−250
−
−
−
−
5.0
45
−45
−50
50
200
−250
−500
nA
IIO/T
−
10
−
−
10
−
−
10
−
pA/°C
Input Common Mode Voltage Range (Note 9),
VCC = 30 V
VCC = 30 V, TA = Thigh to Tlow
VICR
0
−
24.3
0
−
24.3
0
−
24.3
V
0
−
24
0
−
24
0
−
24
Differential Input Voltage Range
VIDR
−
−
VCC
−
−
VCC
−
−
VCC
Large Signal Open Loop Voltage Gain
RL = 2.0 k, VCC = 15 V, For Large VO Swing,
TA = Thigh to Tlow (Note 8)
AVOL
25
15
100
−
−
−
25
15
100
−
−
−
25
15
100
−
−
−
CS
−
−120
−
−
−120
−
−
−120
−
dB
Common Mode Rejection
RS ≤ 10 k
CMR
50
70
−
50
70
−
50
70
−
dB
Power Supply Rejection
PSR
50
100
−
50
100
−
50
100
−
dB
Output Voltage−High Limit
TA = Thigh to Tlow (Note 8)
VCC = 5.0 V, RL = 2.0 k, TA = 25°C
VCC = 30 V, RL = 2.0 k
VCC = 30 V, RL = 10 k
VOH
Output Voltage−Low Limit
VCC = 5.0 V, RL = 10 k,
TA = Thigh to Tlow (Note 8)
Average Temperature Coefficient of Input Offset
Voltage
TA = Thigh to Tlow (Note 8)
Input Offset Current
TA = Thigh to Tlow (Note 8)
Input Bias Current
TA = Thigh to Tlow (Note 8)
Average Temperature Coefficient of Input Offset
Current
TA = Thigh to Tlow (Note 8)
Channel Separation
1.0 kHz ≤ f ≤ 20 kHz, Input Referenced
IIB
V
V/mV
V
3.3
22
23
3.5
−
24
−
−
−
3.3
22
23
3.5
−
24
−
−
−
3.3
22
23
3.5
−
24
−
−
−
VOL
−
5.0
20
−
5.0
20
−
5.0
20
mV
Output Source Current
VID = +1.0 V, VCC = 15 V
IO+
20
40
−
20
40
−
20
40
−
mA
Output Sink Current
VID = −1.0 V, VCC = 15 V
VID = −1.0 V, VO = 200 mV
IO−
10
−
20
−
−
−
10
−
20
−
−
−
10
−
20
−
−
−
mA
A
Output Short Circuit to Ground (Note 10)
ISC
−
40
60
−
40
60
−
40
60
mA
Power Supply Current (Total Device)
TA = Thigh to Tlow (Note 8)
VCC = 30 V, VO = 0 V, RL = ∞
VCC = 5 V, VO = 0 V, RL = ∞
ICC
mA
−
−
1.5
0.7
3.0
1.2
−
−
1.5
0.7
3.0
1.2
−
−
1.5
0.7
3.0
1.2
8. LM258: Tlow = −25°C, Thigh = +85°C
LM358: Tlow = 0°C, Thigh = +70°C
LM2904V & NCV2904: Tlow = −40°C, Thigh = +125°C
LM2904/LM2904A: Tlow = −40°C, Thigh = +105°C
NCV2904 is qualified for automotive use.
9. The input common mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of
the common mode voltage range is VCC − 1.7 V.
10. Short circuits from the output to VCC can cause excessive heating and eventual destruction. Destructive dissipation can result from
simultaneous shorts on all amplifiers.
http://onsemi.com
5
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
CIRCUIT DESCRIPTION
The LM358 series is made using two internally
compensated, two−stage operational amplifiers. The first
stage of each consists of differential input devices Q20 and
Q18 with input buffer transistors Q21 and Q17 and the
differential to single ended converter Q3 and Q4. The first
stage performs not only the first stage gain function but also
performs the level shifting and transconductance reduction
functions. By reducing the transconductance, a smaller
compensation capacitor (only 5.0 pF) can be employed, thus
saving chip area. The transconductance reduction is
accomplished by splitting the collectors of Q20 and Q18.
Another feature of this input stage is that the input common
mode range can include the negative supply or ground, in
single supply operation, without saturating either the input
devices or the differential to single−ended converter. The
second stage consists of a standard current source load
amplifier stage.
Each amplifier is biased from an internal−voltage
regulator which has a low temperature coefficient thus
giving each amplifier good temperature characteristics as
well as excellent power supply rejection.
1.0 V/DIV
VCC = 15 Vdc
RL = 2.0 k
TA = 25°C
5.0 s/DIV
Figure 3. Large Signal Voltage
Follower Response
AVOL, OPEN LOOP VOLTAGE GAIN (dB)
20
VI , INPUT VOLTAGE (V)
18
16
14
12
10
Negative
8.0
Positive
6.0
4.0
2.0
0
120
VCC = 15 V
VEE = Gnd
TA = 25°C
100
80
60
40
20
0
−20
0
2.0
4.0
6.0 8.0
10
12
14 16
VCC/VEE, POWER SUPPLY VOLTAGES (V)
18
1.0
20
10
100
1.0 k
10 k
100 k
1.0 M
f, FREQUENCY (Hz)
Figure 4. Input Voltage Range
Figure 5. Large−Signal Open Loop Voltage Gain
http://onsemi.com
6
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
550
RL = 2.0 k
VCC = 15 V
VEE = Gnd
Gain = −100
RI = 1.0 k
RF = 100 k
12
10
8.0
VO , OUTPUT VOLTAGE (mV)
VOR , OUTPUT VOLTAGE RANGE (Vpp )
14
6.0
4.0
2.0
VCC = 30 V
VEE = Gnd
TA = 25°C
CL = 50 pF
500
Input
450
400
Output
350
300
250
200
0
1.0
0
10
100
f, FREQUENCY (kHz)
1000
0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
t, TIME (ms)
Figure 6. Large−Signal Frequency Response
Figure 7. Small Signal Voltage Follower
Pulse Response (Noninverting)
TA = 25°C
RL = 2.1
I IB , INPUT BIAS CURRENT (nA)
I CC , POWER SUPPLY CURRENT (mA)
2.4
1.8
1.5
1.2
0.9
0.6
0.3
0
0
5.0
10
15
20
25
VCC, POWER SUPPLY VOLTAGE (V)
30
90
80
70
35
0
Figure 8. Power Supply Current versus
Power Supply Voltage
2.0
4.0
6.0 8.0
10
12
14 16
VCC, POWER SUPPLY VOLTAGE (V)
Figure 9. Input Bias Current versus
Supply Voltage
http://onsemi.com
7
18
20
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
50 k
R1
VCC
VCC
R2
5.0 k
−
10 k
1/2
MC1403
2.5 V
1/2
+
VO = 2.5 V (1 +
1
CR
1/2
fo =
1
V
2 CC
R1
)
R2
R
R
C
For: fo = 1.0 kHz
R = 16 k
C = 0.01 F
C
R
LM358
Hysteresis
R2
VOH
−
R1
−
a R1
R1
1/2
+
1/2
LM358
Vin
−
1
CR
−
1/2
+
R
VinH =
eo = C (1 + a + b) (e2 − e1)
H=
Figure 12. High Impedance Differential Amplifier
C1
R2
−
VinL
R2 = R1
TBP
−
100 k
1/2
+
LM358
+
−
R3 = TN R2
1/2
C1 = 10 C
LM358
+
Vref
Bandpass
Output
Vref
1
2 RC
R1 = QR
fo =
C
C
R
Vref
R1
(VOH − VOL)
R1 + R2
100 k
LM358
VinH
R1
(V − V ) + Vref
R1 + R2 OH ref
R
1/2
R2
VOL
Figure 13. Comparator with Hysteresis
R
Vin
VO
R1
(V − V )+ Vref
VinL =
R1 + R2 OL ref
LM358
e2
VO
+
Vref
eo
LM358
b R1
1
2 RC
Figure 11. Wien Bridge Oscillator
Figure 10. Voltage Reference
+
VO
LM358
+
Vref =
e1
VCC
−
Vref
VO
LM358
For: fo
Q
TBP
TN
Vref
R3
R1
−
+
Where: TBP = Center Frequency Gain
TN = Passband Notch Gain
Figure 14. Bi−Quad Filter
8
= 1.0 kHz
= 10
=1
=1
Notch Output
LM358
http://onsemi.com
1
V
2 CC
C1
1/2
Vref
Vref =
R
C
R1
R2
R3
= 160 k
= 0.001 F
= 1.6 M
= 1.6 M
= 1.6 M
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
VCC
C
Vin
R1
R3
C
−
1/2
LM358
+
R2
Vref
Given:
VO
CO
CO = 10 C
1
Vref = 2 VCC
fo = center frequency
A(fo) = gain at center frequency
Choose value fo, C
Vref =
Vref
1
V
2 CC
Triangle Wave
Output
+
300 k
R3
1/2
LM358
−
75 k
R1
100 k
LM358
−
Square
Wave
Output
R1 + RC
4 CRf R1
Q
fo C
R1 =
R3
2 A(fo)
R2 =
R1 R3
4Q2 R1 −R3
For less than 10% error from operational amplifier.
Qo fo
< 0.1
BW
Where fo and BW are expressed in Hz.
Rf
f =
R3 =
+
1/2
Vref
C
Then:
R2
if, R3 =
R2 R1
R2 + R1
If source impedance varies, filter may be preceded with voltage
follower buffer to stabilize filter parameters.
Figure 16. Multiple Feedback Bandpass Filter
Figure 15. Function Generator
http://onsemi.com
9
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
ORDERING INFORMATION
Device
Operating Temperature Range
Package
Shipping†
LM358D
SOIC−8
98 Units/Rail
LM358DR2
SOIC−8
2500 Tape & Reel
SOIC−8
(Pb−Free)
2500 Tape & Reel
Micro8
4000 Tape & Reel
Micro8
(Pb−Free)
4000 Tape & Reel
PDIP−8
50 Units/Rail
PDIP−8
(Pb−Free)
50 Units/Rail
LM258D
SOIC−8
98 Units/Rail
LM258DR2
SOIC−8
2500 Tape & Reel
SOIC−8
(Pb−Free)
2500 Tape & Reel
LM258DMR2
Micro8
4000 Tape & Reel
LM258N
PDIP−8
50 Units/Rail
LM2904D
SOIC−8
98 Units/Rail
LM2904DR2
SOIC−8
2500 Tape & Reel
SOIC−8
(Pb−Free)
2500 Tape & Reel
Micro8
2500 Tape & Reel
Micro8
(Pb−Free)
2500 Tape & Reel
LM2904N
PDIP−8
50 Units/Rail
LM2904ADMR2
Micro8
4000 Tape & Reel
LM2904AN
PDIP−8
50 Units/Rail
LM2904VD
SOIC−8
98 Units/Rail
SOIC−8
(Pb−Free)
98 Units/Rail
SOIC−8
2500 Tape & Reel
Micro8
4000 Tape & Reel
LM358DR2G
LM358DMR2
0°C to +70°C
LM358DMR2G
LM358N
LM358NG
LM258DR2G
−25°C to +85°C
LM2904DR2G
LM2904DMR2
LM2904DMR2G
−40°C
40°C to +105°C
LM2904VDG
LM2904VDR2
LM2904VDMR2
−40°C to +125°C
LM2904VN
PDIP−8
50 Units/Rail
NCV2904DR2*
SOIC−8
2500 Tape & Reel
NCV2904DMR2*
Micro8
4000 Tape & Reel
*NCV2904 is qualified for automotive use.
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
10
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
MARKING DIAGRAMS
PDIP−8
AN SUFFIX
CASE 626
PDIP−8
N SUFFIX
CASE 626
8
8
LMx58N
AWL
YYWW
8
LM2904N
AWL
YYWW
1
PDIP−8
VN SUFFIX
CASE 626
8
LM2904AN
AWL
YYWW
1
LM2904VN
AWL
YYWW
1
1
SOIC−8
VD SUFFIX
CASE 751
SOIC−8
D SUFFIX
CASE 751
8
8
LMx58
ALYW
8
2904
ALYW
1
*
2904V
ALYW
1
1
Micro8
DMR2 SUFFIX
CASE 846A
8
8
x58
AYW
1
8
2904
AYW
8
904A
AYW
1
1
x
A
WL, L
YY, Y
WW, W
= 2 or 3
= Assembly Location
= Wafer Lot
= Year
= Work Week
*This diagram also applies to NCV2904
http://onsemi.com
11
904V
AYW
1
*
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
PACKAGE DIMENSIONS
PDIP−8
N, AN, VN SUFFIX
CASE 626−05
ISSUE L
8
NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5
−B−
1
4
F
−A−
NOTE 2
L
C
J
−T−
N
SEATING
PLANE
D
H
M
K
G
0.13 (0.005)
M
T A
M
B
M
http://onsemi.com
12
DIM
A
B
C
D
F
G
H
J
K
L
M
N
MILLIMETERS
MIN
MAX
9.40
10.16
6.10
6.60
3.94
4.45
0.38
0.51
1.02
1.78
2.54 BSC
0.76
1.27
0.20
0.30
2.92
3.43
7.62 BSC
−−−
10
0.76
1.01
INCHES
MIN
MAX
0.370
0.400
0.240
0.260
0.155
0.175
0.015
0.020
0.040
0.070
0.100 BSC
0.030
0.050
0.008
0.012
0.115
0.135
0.300 BSC
−−−
10
0.030
0.040
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
PACKAGE DIMENSIONS
SOIC−8
D, VD SUFFIX
CASE 751−07
ISSUE AB
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
−X−
A
8
5
S
B
1
0.25 (0.010)
M
Y
M
4
K
−Y−
G
C
N
DIM
A
B
C
D
G
H
J
K
M
N
S
X 45 SEATING
PLANE
−Z−
0.10 (0.004)
H
D
0.25 (0.010)
M
Z Y
S
X
M
J
S
SOLDERING FOOTPRINT*
1.52
0.060
7.0
0.275
4.0
0.155
0.6
0.024
1.270
0.050
SCALE 6:1
mm inches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
13
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0
8
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0 8 0.010
0.020
0.228
0.244
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
PACKAGE DIMENSIONS
Micro8
DMR2 SUFFIX
CASE 846A−02
ISSUE F
−A−
−B−
K
PIN 1 ID
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED 0.25 (0.010)
PER SIDE.
5. 846A−01 OBSOLETE, NEW STANDARD 846A−02.
G
D 8 PL
0.08 (0.003)
M
T B
A
S
DIM
A
B
C
D
G
H
J
K
L
S
SEATING
−T− PLANE
0.038 (0.0015)
C
L
J
H
MILLIMETERS
MIN
MAX
2.90
3.10
2.90
3.10
−−−
1.10
0.25
0.40
0.65 BSC
0.05
0.15
0.13
0.23
4.75
5.05
0.40
0.70
INCHES
MIN
MAX
0.114
0.122
0.114
0.122
−−−
0.043
0.010
0.016
0.026 BSC
0.002
0.006
0.005
0.009
0.187
0.199
0.016
0.028
SOLDERING FOOTPRINT*
8X
1.04
0.041
0.38
0.015
3.20
0.126
6X
8X
4.24
0.167
0.65
0.0256
5.28
0.208
SCALE 8:1
mm inches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
Micro8 is a trademark of International Rectifier.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
http://onsemi.com
14
For additional information, please contact your
local Sales Representative.
LM358/D