Freescale MPC5533MVF66 Microcontroller data sheet Datasheet

Document Number: MPC5533
Rev. 0.0, 10 Oct 2008
Freescale Semiconductor
Data Sheet: Technical Data
MPC5533
Microcontroller Data Sheet
by: Microcontroller Division
This document provides electrical specifications, pin
assignments, and package diagrams for the MPC5533
microcontroller device. For functional characteristics,
refer to the MPC5534 Microcontroller Reference
Manual.
1
Contents
1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1 Maximum Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.2 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . 5
3.3 Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.4 EMI Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.5 ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.6 VRC and POR Electrical Specifications . . . . . . . . . 9
3.7 Power-Up/Down Sequencing. . . . . . . . . . . . . . . . . 10
3.8 DC Electrical Specifications . . . . . . . . . . . . . . . . . 13
3.9 Oscillator and FMPLL Electrical Characteristics . . 20
3.10 eQADC Electrical Characteristics . . . . . . . . . . . . . 22
3.11 H7Fb Flash Memory Electrical Characteristics . . . 23
3.12 AC Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.13 AC Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4
Mechanicals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1 MPC5533 208 MAP BGA Pinout . . . . . . . . . . . . . .
4.2 MPC5533 324 PBGA Pinout . . . . . . . . . . . . . . . . .
4.3 MPC5533 208-Pin Package Dimensions. . . . . . . .
4.4 MPC5533 324-Pin Package Dimensions. . . . . . . .
Overview
The MPC5533 microcontroller (MCU) is a member of
the MPC5500 family of microcontrollers built on the
Power Architecture™ embedded technology. This
family of parts has many new features coupled with high
performance CMOS technology to provide substantial
reduction of cost per feature and significant performance
improvement over the MPC500 family.
The host processor core of this device complies with the
Power Architecture embedded category that is 100%
user-mode compatible (including floating point library)
with the original Power PC™ user instruction set
architecture (UISA). The embedded architecture
enhancements improve the performance in embedded
applications. The core also has additional instructions,
including digital signal processing (DSP) instructions,
beyond the original Power PC instruction set.
© Freescale Semiconductor, Inc., 2008. All rights reserved.
5
43
43
44
45
47
Revision History for the MPC5533 Data Sheet . . . . . . . 49
Overview
The MPC5500 family of parts contains many new features coupled with high performance CMOS
technology to provide significant performance improvement over the MPC565.
The host processor core of the MPC5533 also includes an instruction set enhancement allowing variable
length encoding (VLE). This allows optional encoding of mixed 16- and 32-bit instructions. With this
enhancement, it is possible to significantly reduce the code size footprint.
The MPC5533 has a single-level memory hierarchy consisting of 48-kilobytes (KB) on-chip SRAM and
768 KB of internal flash memory. Both the SRAM and the flash memory can hold instructions and data.
The complex input/output timer functions of the MPC5533 are performed by an enhanced time processor
unit (eTPU) engine. The eTPU engine controls 32 hardware channels. The eTPU has been enhanced over
the TPU by providing: 24-bit timers, double-action hardware channels, variable number of parameters per
channel, angle clock hardware, and additional control and arithmetic instructions. The eTPU is
programmed using a high-level programming language.
Off-chip communication is performed by a suite of serial protocols including controller area networks
(FlexCANs), enhanced deserial/serial peripheral interfaces (DSPIs), and an enhanced serial
communications interface (eSCI).
The MCU has an on-chip enhanced queued analog-to-digital converter (eQADC) with a 5 V conversion
range. The 324 package has 40-channels; the 208 package has 34 channels.
The system integration unit (SIU) performs several chip-wide configuration functions. Pad configuration
and general-purpose input and output (GPIO) are controlled from the SIU. Interrupts and reset control are
also determined by the SIU. The internal multiplexer sub-block (IMUX) provides multiplexing of eQADC
trigger sources and external interrupt signal multiplexing.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
2
Freescale Semiconductor
Ordering Information
2
Ordering Information
M PC 5533 M VF 80 R
Qualification status
Core code
Device number
Temperature range
Package identifier
Operating frequency (MHz)
Tape and reel status
Temperature Range
M = –40° C to 125° C
Package Identifier
VF = 208MAPBGA SnPb
VM = 208MAPBGA Pb-free
ZQ = 324PBGA SnPb
VZ = 324PBGA Pb-free
Operating Frequency
40 = 40 MHz
66 = 66 MHz
80 = 80 MHz
Tape and Reel Status
R = Tape and reel
(blank) = Trays
Qualification Status
P = Pre qualification
M = Fully spec. qualified, general market flow
S = Fully spec. qualified, automotive flow
Note: Not all options are available on all devices. Refer to Table 1.
Figure 1. MPC5500 Family Part Number Example
Unless noted in this data sheet, all specifications apply from TL to TH.
Table 1. Orderable Part Numbers
Speed (MHz)
Freescale Part Number
Package Description
MPC5533MVM80
MPC5533MVM66
MPC5533 208 package
Lead-free (PbFree)
MPC5533MVM40
MPC5533MVF80
MPC5533MVF66
MPC5533 208 package
Leaded (SnPb)
MPC5533MVF40
MPC5533MVZ80
MPC5533MVZ66
MPC5533 324 package
Lead-free (PbFree)
MPC5533MVZ40
MPC5533MZQ80
MPC5533MZQ66
MPC5533MZQ40
1
2
Operating Temperature 1
MPC5533 324 package
Leaded (SnPb)
Nominal
Max. 2 (fMAX)
80
82
66
68
40
42
80
82
66
68
40
42
80
82
66
68
40
42
80
82
66
68
40
42
Min. (TL)
Max. (TH)
–40° C
125° C
–40° C
125° C
–40° C
125° C
–40° C
125° C
The lowest ambient operating temperature is referenced by TL; the highest ambient operating temperature is referenced by TH.
Speed is the nominal maximum frequency. Max. speed is the maximum speed allowed including frequency modulation (FM).
42 MHz parts allow for 40 MHz system clock + 2% FM; 68 MHz parts allow for 66 MHz system clock + 2% FM, and
82 MHz parts allow for 80 MHz system clock + 2% FM.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
3
Electrical Characteristics
3
Electrical Characteristics
This section contains detailed information on power considerations, DC/AC electrical characteristics, and
AC timing specifications for the MCU.
3.1
Maximum Rating
Table 2. Absolute Maximum Ratings 1
Spec
Characteristic
Symbol
Min.
Max.
Unit
1
1.5 V core supply voltage 2
VDD
–0.3
1.7
V
2
Flash program/erase voltage
VPP
–0.3
6.5
V
4
Flash read voltage
VFLASH
–0.3
4.6
V
5
SRAM standby voltage
VSTBY
–0.3
1.7
V
6
Clock synthesizer voltage
VDDSYN
–0.3
4.6
V
7
3.3 V I/O buffer voltage
VDD33
–0.3
4.6
V
8
Voltage regulator control input voltage
VRC33
–0.3
4.6
V
9
Analog supply voltage (reference to VSSA)
VDDA
–0.3
5.5
V
VDDE
–0.3
4.6
V
VDDEH
–0.3
6.5
V
–1.0 5
–1.0 5
6.5 6
4.6 7
V
10
11
12
I/O supply voltage (fast I/O pads)
3
I/O supply voltage (slow and medium I/O pads)
3
4
DC input voltage
VDDEH powered I/O pads
VDDE powered I/O pads
VIN
13
Analog reference high voltage (reference to VRL)
VRH
–0.3
5.5
V
14
VSS to VSSA differential voltage
VSS – VSSA
–0.1
0.1
V
15
VDD to VDDA differential voltage
VDD – VDDA
–VDDA
VDD
V
16
VREF differential voltage
VRH – VRL
–0.3
5.5
V
17
VRH to VDDA differential voltage
VRH – VDDA
–5.5
5.5
V
18
VRL to VSSA differential voltage
VRL – VSSA
–0.3
0.3
V
19
VDDEH to VDDA differential voltage
VDDEH – VDDA
–VDDA
VDDEH
V
20
VDDF to VDD differential voltage
VDDF – VDD
–0.3
0.3
V
21
VRC33 to VDDSYN differential voltage spec has been moved to Table 9 DC Electrical Specifications, Spec 43a.
22
VSSSYN to VSS differential voltage
VSSSYN – VSS
–0.1
0.1
V
23
VRCVSS to VSS differential voltage
VRCVSS – VSS
–0.1
0.1
V
24
Maximum DC digital input current 8
(per pin, applies to all digital pins) 4
IMAXD
–2
2
mA
25
Maximum DC analog input current 9
(per pin, applies to all analog pins)
IMAXA
–3
3
mA
26
Maximum operating temperature range 10
Die junction temperature
TJ
TL
150.0
oC
27
Storage temperature range
TSTG
–55.0
150.0
oC
MPC5533 Microcontroller Data Sheet, Rev. 0.0
4
Freescale Semiconductor
Electrical Characteristics
Table 2. Absolute Maximum Ratings 1 (continued)
Spec
28
29
Characteristic
Symbol
Min.
Max.
Maximum solder temperature 11
Lead free (Pb-free)
Leaded (SnPb)
TSDR
—
—
260.0
245.0
Moisture sensitivity level 12
MSL
—
3
Unit
o
C
1
Functional operating conditions are given in the DC electrical specifications. Absolute maximum ratings are stress ratings only,
and functional operation at the maxima is not guaranteed. Stress beyond any of the listed maxima can affect device reliability
or cause permanent damage to the device.
2
1.5 V ± 10% for proper operation. This parameter is specified at a maximum junction temperature of 150 oC.
3
All functional non-supply I/O pins are clamped to VSS and VDDE, or VDDEH.
4
AC signal overshoot and undershoot of up to ± 2.0 V of the input voltages is permitted for an accumulative duration of
60 hours over the complete lifetime of the device (injection current not limited for this duration).
5
Internal structures hold the voltage greater than –1.0 V if the injection current limit of 2 mA is met. Keep the negative DC
voltage greater than –0.6 V on SINB during the internal power-on reset (POR) state.
6 Internal structures hold the input voltage less than the maximum voltage on all pads powered by V
DDEH supplies, if the
maximum injection current specification is met (2 mA for all pins) and VDDEH is within the operating voltage specifications.
7 Internal structures hold the input voltage less than the maximum voltage on all pads powered by V
DDE supplies, if the maximum
injection current specification is met (2 mA for all pins) and VDDE is within the operating voltage specifications.
8 Total injection current for all pins (including both digital and analog) must not exceed 25 mA.
9 Total injection current for all analog input pins must not exceed 15 mA.
10 Lifetime operation at these specification limits is not guaranteed.
11 Moisture sensitivity profile per IPC/JEDEC J-STD-020D.
12 Moisture sensitivity per JEDEC test method A112.
3.2
Thermal Characteristics
The shaded rows in the following table indicate information specific to a four-layer board.
Table 3. MPC5533 Thermal Characteristic
Package
Spec
1
MPC5533 Thermal Characteristic
Junction to ambient 1, 2, natural convection (one-layer board)
1, 3
208
MAPBGA
324
PBGA
Unit
RθJA
42
34
°C/W
RθJA
26
23
°C/W
2
Junction to ambient
3
Junction to ambient (@200 ft./min., one-layer board)
RθJMA
34
28
°C/W
4
Junction to ambient (@200 ft./min., four-layer board 2s2p)
RθJMA
22
20
°C/W
RθJB
15
15
°C/W
RθJC
8
10
°C/W
ΨJT
2
2
°C/W
5
6
7
, natural convection (four-layer board 2s2p)
Symbol
4
Junction to board (four-layer board 2s2p)
Junction to case
5
6
Junction to package top , natural convection
1
Junction temperature is a function of: on-chip power dissipation, package thermal resistance, mounting site (board)
temperature, ambient temperature, air flow, power dissipation of other board components, and board thermal resistance.
2 Per SEMI G38-87 and JEDEC JESD51-2 with the single-layer board in a horizontal position.
3 Per JEDEC JESD51-6 with the board in a horizontal position.
4 Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on
the top surface of the board near the package.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
5
Electrical Characteristics
5
Indicates the average thermal resistance between the die and the case top surface as measured by the cold plate method
(MIL SPEC-883 Method 1012.1) with the cold plate temperature used for the case temperature.
6
The thermal characterization parameter indicates the temperature difference between the package top and the junction
temperature per JEDEC JESD51-2.
3.2.1
General Notes for Specifications at Maximum Junction Temperature
An estimation of the device junction temperature, TJ, can be obtained from the equation:
TJ = TA + (RθJA × PD)
where:
TA = ambient temperature for the package (oC)
RθJA = junction to ambient thermal resistance (oC/W)
PD = power dissipation in the package (W)
The thermal resistance values used are based on the JEDEC JESD51 series of standards to provide
consistent values for estimations and comparisons. The difference between the values determined for the
single-layer (1s) board compared to a four-layer board that has two signal layers, a power and a ground
plane (2s2p), demonstrate that the effective thermal resistance is not a constant. The thermal resistance
depends on the:
• Construction of the application board (number of planes)
• Effective size of the board which cools the component
• Quality of the thermal and electrical connections to the planes
• Power dissipated by adjacent components
Connect all the ground and power balls to the respective planes with one via per ball. Using fewer vias to
connect the package to the planes reduces the thermal performance. Thinner planes also reduce the thermal
performance. When the clearance between the vias leave the planes virtually disconnected, the thermal
performance is also greatly reduced.
As a general rule, the value obtained on a single-layer board is within the normal range for the tightly
packed printed circuit board. The value obtained on a board with the internal planes is usually within the
normal range if the application board has:
• One oz. (35 micron nominal thickness) internal planes
• Components are well separated
• Overall power dissipation on the board is less than 0.02 W/cm2
The thermal performance of any component depends on the power dissipation of the surrounding
components. In addition, the ambient temperature varies widely within the application. For many natural
convection and especially closed box applications, the board temperature at the perimeter (edge) of the
package is approximately the same as the local air temperature near the device. Specifying the local
ambient conditions explicitly as the board temperature provides a more precise description of the local
ambient conditions that determine the temperature of the device.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
6
Freescale Semiconductor
Electrical Characteristics
At a known board temperature, the junction temperature is estimated using the following equation:
TJ = TB + (RθJB × PD)
where:
TJ = junction temperature (oC)
TB = board temperature at the package perimeter (oC/W)
RθJB = junction-to-board thermal resistance (oC/W) per JESD51-8
PD = power dissipation in the package (W)
When the heat loss from the package case to the air does not factor into the calculation, an acceptable value
for the junction temperature is predictable. Ensure the application board is similar to the thermal test
condition, with the component soldered to a board with internal planes.
The thermal resistance is expressed as the sum of a junction-to-case thermal resistance plus a
case-to-ambient thermal resistance:
RθJA = RθJC + RθCA
where:
RθJA = junction-to-ambient thermal resistance (oC/W)
RθJC = junction-to-case thermal resistance (oC/W)
RθCA = case-to-ambient thermal resistance (oC/W)
RθJC is device related and is not affected by other factors. The thermal environment can be controlled to
change the case-to-ambient thermal resistance, RθCA. For example, change the air flow around the device,
add a heat sink, change the mounting arrangement on the printed circuit board, or change the thermal
dissipation on the printed circuit board surrounding the device. This description is most useful for
packages with heat sinks where 90% of the heat flow is through the case to heat sink to ambient.
For most packages, a better model is required.
A more accurate two-resistor thermal model can be constructed from the junction-to-board thermal
resistance and the junction-to-case thermal resistance. The junction-to-case thermal resistance describes
when using a heat sink or where a substantial amount of heat is dissipated from the top of the package. The
junction-to-board thermal resistance describes the thermal performance when most of the heat is
conducted to the printed circuit board. This model can be used to generate simple estimations and for
computational fluid dynamics (CFD) thermal models.
To determine the junction temperature of the device in the application on a prototype board, use the
thermal characterization parameter (ΨJT) to determine the junction temperature by measuring the
temperature at the top center of the package case using the following equation:
TJ = TT + (ΨJT × PD)
where:
TT = thermocouple temperature on top of the package (oC)
ΨJT = thermal characterization parameter (oC/W)
PD = power dissipation in the package (W)
The thermal characterization parameter is measured in compliance with the JESD51-2 specification using
a 40-gauge type T thermocouple epoxied to the top center of the package case. Position the thermocouple
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
7
Electrical Characteristics
so that the thermocouple junction rests on the package. Place a small amount of epoxy on the thermocouple
junction and approximately 1 mm of wire extending from the junction. Place the thermocouple wire flat
against the package case to avoid measurement errors caused by the cooling effects of the thermocouple
wire.
References:
Semiconductor Equipment and Materials International
3081 Zanker Rd.
San Jose, CA., 95134
(408) 943-6900
MIL-SPEC and EIA/JESD (JEDEC) specifications are available from Global Engineering Documents at
800-854-7179 or 303-397-7956.
JEDEC specifications are available on the web at http://www.jedec.org.
• 1. C.E. Triplett and B. Joiner, “An Experimental Characterization of a 272 PBGA Within an
Automotive Engine Controller Module,” Proceedings of SemiTherm, San Diego, 1998, pp. 47–54.
• 2. G. Kromann, S. Shidore, and S. Addison, “Thermal Modeling of a PBGA for Air-Cooled
Applications,” Electronic Packaging and Production, pp. 53–58, March 1998.
• 3. B. Joiner and V. Adams, “Measurement and Simulation of Junction to Board Thermal Resistance
and Its Application in Thermal Modeling,” Proceedings of SemiTherm, San Diego, 1999,
pp. 212–220.
3.3
Package
The MPC5533 is available in packaged form. Read the package options in Section 2, “Ordering
Information.” Refer to Section 4, “Mechanicals,” for pinouts and package drawings.
3.4
EMI (Electromagnetic Interference) Characteristics
Table 4. EMI Testing Specifications 1
Spec
Characteristic
Minimum
Typical
Maximum
Unit
0.15
—
1000
MHz
1
Scan range
2
Operating frequency
—
—
fMAX
MHz
3
VDD operating voltages
—
1.5
—
V
4
VDDSYN, VRC33, VDD33, VFLASH, VDDE operating voltages
—
3.3
—
V
5
VPP, VDDEH, VDDA operating voltages
—
5.0
—
V
6
Maximum amplitude
—
—
14 2
32 3
dBuV
7
Operating temperature
—
—
25
oC
1
EMI testing and I/O port waveforms per SAE J1752/3 issued 1995-03. Qualification testing was performed on the MPC5554
and applied to the MPC5500 family as generic EMI performance data.
2
Measured with the single-chip EMI program.
3
Measured with the expanded EMI program.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
8
Freescale Semiconductor
Electrical Characteristics
3.5
ESD (Electromagnetic Static Discharge) Characteristics
Table 5. ESD Ratings 1, 2
Characteristic
Symbol
Value
Unit
2000
V
R1
1500
Ω
C
100
pF
ESD for human body model (HBM)
HBM circuit description
500 (all pins)
ESD for field induced charge model (FDCM)
V
750 (corner pins)
Number of pulses per pin:
Positive pulses (HBM)
Negative pulses (HBM)
—
—
1
1
—
—
Interval of pulses
—
1
second
1
2
All ESD testing conforms to CDF-AEC-Q100 Stress Test Qualification for Automotive Grade Integrated Circuits.
Device failure is defined as: ‘If after exposure to ESD pulses, the device does not meet the device specification requirements,
which includes the complete DC parametric and functional testing at room temperature and hot temperature.
3.6
Voltage Regulator Controller (VRC) and Power-On Reset (POR)
Electrical Specifications
The following table lists the VRC and POR electrical specifications:
Table 6. VRC/POR Electrical Specifications
Spec
1
Characteristic
3.3 V (VDDSYN) POR
3
RESET pin supply
(VDDEH6) POR 1, 2
1
VRC33 voltage
6
Current can be sourced
7
Max.
Units
VPOR15
1.1
1.1
1.35
1.35
V
Asserted (ramp up)
Negated (ramp up)
Asserted (ramp down)
Negated (ramp down)
VPOR33
0.0
2.0
2.0
0.0
0.30
2.85
2.85
0.30
V
Negated (ramp up)
Asserted (ramp down)
VPOR5
2.0
2.0
2.85
2.85
V
VTRANS_START
1.0
2.0
V
When VRC allows the pass transistor
to completely turn on 3, 4
VTRANS_ON
2.0
2.85
V
When the voltage is greater than the
voltage at which the VRC keeps the
1.5 V supply in regulation 5, 6
VVRC33REG
3.0
—
V
11.0
—
mA
9.0
—
mA
7.5
—
mA
—
1.0
V
Before VRC allows the pass
transistor to start turning on
4
5
Min.
Negated (ramp up)
Asserted (ramp down)
1.5 V (VDD) POR 1
2
Symbol
by VRCCTL at Tj:
– 40o C
o
25 C
150o
8
IVRCCTL
7
C
Voltage differential during power up such that:
VDD33 can lag VDDSYN or VDDEH6, before VDDSYN and VDDEH6 reach the
VPOR33 and VPOR5 minimums respectively.
VDD33_LAG
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
9
Electrical Characteristics
Table 6. VRC/POR Electrical Specifications (continued)
Spec
9
10
Characteristic
Symbol
Min.
Max.
Units
—
—
50
V/ms
35
—
—
40
—
—
50
500
—
Absolute value of slew rate on power supply pins
Required gain at Tj:
IDD ÷ IVRCCTL (@ fsys = fMAX)
6, 7, 8, 9
o
– 40 C
o
25 C
BETA10
o
150 C
1
On power up, assert RESET before VPOR15, VPOR33, and VPOR5 negate (internal POR). RESET must remain asserted until
the power supplies are within the operating conditions as specified in Table 9 DC Electrical Specifications. On power down,
assert RESET before any power supplies fall outside the operating conditions and until the internal POR asserts.
2
VIL_S (Table 9, Spec15) is guaranteed to scale with VDDEH6 down to VPOR5.
3
Supply full operating current for the 1.5 V supply when the 3.3 V supply reaches this range.
4
It is possible to reach the current limit during ramp up—do not treat this event as short circuit current.
5
At peak current for device.
6
Requires compliance with Freescale’s recommended board requirements and transistor recommendations. Board signal
traces/routing from the VRCCTL package signal to the base of the external pass transistor and between the emitter of the pass
transistor to the VDD package signals must have a maximum of 100 nH inductance and minimal resistance
(less than 1 Ω). VRCCTL must have a nominal 1 μF phase compensation capacitor to ground. VDD must have a 20 μF (nominal)
bulk capacitor (greater than 4 μF over all conditions, including lifetime). Place high-frequency bypass capacitors consisting of
eight 0.01 μF, two 0.1 μF, and one 1 μF capacitors around the package on the VDD supply signals.
7 I
VRCCTL is measured at the following conditions: VDD = 1.35 V, VRC33 = 3.1 V, VVRCCTL = 2.2 V.
8 Refer to Table 1 for the maximum operating frequency.
9 Values are based on I
DD from high-use applications as explained in the IDD Electrical Specification.
10 BETA represents the worst-case external transistor. It is measured on a per-part basis and calculated as (I
DD ÷ IVRCCTL).
3.7
Power-Up/Down Sequencing
Power sequencing between the 1.5 V power supply and VDDSYN or the RESET power supplies is required
if using an external 1.5 V power supply with VRC33 tied to ground (GND). To avoid power-sequencing,
VRC33 must be powered up within the specified operating range, even if the on-chip voltage regulator
controller is not used. Refer to Section 3.7.2, “Power-Up Sequence (VRC33 Grounded),” and
Section 3.7.3, “Power-Down Sequence (VRC33 Grounded).”
Power sequencing requires that VDD33 must reach a certain voltage where the values are read as ones
before the POR signal negates. Refer to Section 3.7.1, “Input Value of Pins During POR Dependent on
VDD33.”
Although power sequencing is not required between VRC33 and VDDSYN during power up, VRC33 must
not lead VDDSYN by more than 600 mV or lag by more than 100 mV for the VRC stage turn-on to operate
within specification. Higher spikes in the emitter current of the pass transistor occur if VRC33 leads or lags
VDDSYN by more than these amounts. The value of that higher spike in current depends on the board power
supply circuitry and the amount of board level capacitance.
Furthermore, when all of the PORs negate, the system clock starts to toggle, adding another large increase
of the current consumed by VRC33. If VRC33 lags VDDSYN by more than 100 mV, the increase in current
consumed can drop VDD low enough to assert the 1.5 V POR again. Oscillations are possible when the
1.5 V POR asserts and stops the system clock, causing the voltage on VDD to rise until the 1.5 V POR
negates again. All oscillations stop when VRC33 is powered sufficiently.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
10
Freescale Semiconductor
Electrical Characteristics
When powering down, VRC33 and VDDSYN have no delta requirement to each other, because the bypass
capacitors internal and external to the device are already charged. When not powering up or down, no delta
between VRC33 and VDDSYN is required for the VRC to operate within specification.
There are no power up/down sequencing requirements to prevent issues such as latch-up, excessive current
spikes, and so on. Therefore, the state of the I/O pins during power up and power down varies depending
on which supplies are powered.
Table 7 gives the pin state for the sequence cases for all pins with pad type pad_fc (fast type).
Table 7. Pin Status for Fast Pads During the Power Sequence
VDDE
VDD33
VDD
POR
Pin Status for Fast Pad Output Driver
pad_fc (fast)
Low
—
—
Asserted
Low
VDDE
Low
Low
Asserted
High
VDDE
Low
VDD
Asserted
High
VDDE
VDD33
Low
Asserted
High impedance (Hi-Z)
VDDE
VDD33
VDD
Asserted
Hi-Z
VDDE
VDD33
VDD
Negated
Functional
Table 8 gives the pin state for the sequence cases for all pins with pad type pad_mh (medium type) and
pad_sh (slow type).
Table 8. Pin Status for Medium and Slow Pads During the Power Sequence
VDDEH
VDD
POR
Pin Status for Medium and Slow Pad Output Driver
pad_mh (medium) pad_sh (slow)
Low
—
Asserted
Low
VDDEH
Low
Asserted
High impedance (Hi-Z)
VDDEH
VDD
Asserted
Hi-Z
VDDEH
VDD
Negated
Functional
The values in Table 7 and Table 8 do not include the effect of the weak-pull devices on the output pins
during power up.
Before exiting the internal POR state, the pins go to a high-impedance state until POR negates. When the
internal POR negates, the functional state of the signal during reset applies and the weak-pull devices (up
or down) are enabled as defined in the device reference manual. If VDD is too low to correctly propagate
the logic signals, the weak-pull devices can pull the signals to VDDE and VDDEH.
To avoid this condition, minimize the ramp time of the VDD supply to a time period less than the time
required to enable the external circuitry connected to the device outputs.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
11
Electrical Characteristics
3.7.1
Input Value of Pins During POR Dependent on VDD33
When powering up the device, VDD33 must not lag the latest VDDSYN or RESET power pin (VDDEH6) by
more than the VDD33 lag specification listed in Table 6, spec 8. This avoids accidentally selecting the
bypass clock mode because the internal versions of PLLCFG[0:1] and RSTCFG are not powered and
therefore cannot read the default state when POR negates. VDD33 can lag VDDSYN or the RESET power
pin (VDDEH6), but cannot lag both by more than the VDD33 lag specification. This VDD33 lag specification
applies during power up only. VDD33 has no lead or lag requirements when powering down.
3.7.2
Power-Up Sequence (VRC33 Grounded)
The 1.5 V VDD power supply must rise to 1.35 V before the 3.3 V VDDSYN power supply and the RESET
power supply rises above 2.0 V. This ensures that digital logic in the PLL for the 1.5 V power supply does
not begin to operate below the specified operation range lower limit of 1.35 V. Because the internal 1.5 V
POR is disabled, the internal 3.3 V POR or the RESET power POR must hold the device in reset. Since
they can negate as low as 2.0 V, VDD must be within specification before the 3.3 V POR and the RESET
POR negate.
VDDSYN and RESET Power
VDD
2.0 V
1.35 V
VDD must reach 1.35 V before VDDSYN and the RESET power reach 2.0 V
Figure 2. Power-Up Sequence (VRC33 Grounded)
3.7.3
Power-Down Sequence (VRC33 Grounded)
The only requirement for the power-down sequence with VRC33 grounded is if VDD decreases to less than
its operating range, VDDSYN or the RESET power must decrease to less than 2.0 V before the VDD power
increases to its operating range. This ensures that the digital 1.5 V logic, which is reset only by an ORed
POR and can cause the 1.5 V supply to decrease less than its specification value, resets correctly.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
12
Freescale Semiconductor
Electrical Characteristics
3.8
DC Electrical Specifications
Table 9. DC Electrical Specifications (TA = TL – TH)
Spec
1
Characteristic
Core supply voltage (average DC RMS voltage)
1
Symbol
Min
Max.
Unit
VDD
1.35
1.65
V
VDDE
1.62
3.6
V
2
Input/output supply voltage (fast input/output)
3
Input/output supply voltage (slow and medium input/output)
VDDEH
3.0
5.25
V
4
3.3 V input/output buffer voltage
VDD33
3.0
3.6
V
5
Voltage regulator control input voltage
VRC33
3.0
3.6
V
VDDA
4.5
5.25
V
VPP
4.5
5.25
V
2
6
Analog supply voltage
8
Flash programming voltage 3
9
Flash read voltage
VFLASH
3.0
3.6
V
10
SRAM standby voltage 4
VSTBY
0.8
1.2
V
11
Clock synthesizer operating voltage
VDDSYN
3.0
3.6
V
12
Fast I/O input high voltage
VIH_F
0.65 × VDDE
VDDE + 0.3
V
13
Fast I/O input low voltage
VIL_F
VSS – 0.3
0.35 × VDDE
V
14
Medium and slow I/O input high voltage
VIH_S
0.65 × VDDEH
VDDEH + 0.3
V
15
Medium and slow I/O input low voltage
VIL_S
VSS – 0.3
0.35 × VDDEH
V
16
Fast input hysteresis
VHYS_F
0.1 × VDDE
V
17
Medium and slow I/O input hysteresis
VHYS_S
0.1 × VDDEH
V
18
Analog input voltage
VINDC
VSSA – 0.3
VDDA + 0.3
V
19
Fast output high voltage ( IOH_F = –2.0 mA )
VOH_F
0.8 × VDDE
—
V
20
Slow and medium output high voltage
IOH_S = –2.0 mA
IOH_S = –1.0 mA
VOH_S
0.80 × VDDEH
0.85 × VDDEH
—
V
21
Fast output low voltage ( IOL_F = 2.0 mA )
VOL_F
—
0.2 × VDDE
V
22
Slow and medium output low voltage
IOL_S = 2.0 mA
IOL_S = 1.0 mA
VOL_S
—
Load capacitance (fast I/O) 5
DSC (SIU_PCR[8:9] ) = 0b00
= 0b01
= 0b10
= 0b11
CL
24
Input capacitance (digital pins)
25
26
23
V
0.20 × VDDEH
0.15 × VDDEH
—
—
—
—
10
20
30
50
pF
pF
pF
pF
CIN
—
7
pF
Input capacitance (analog pins)
CIN_A
—
10
pF
Input capacitance:
(Shared digital and analog pins AN[12]_MA[0]_SDS,
AN[13]_MA[1]_SDO, AN[14]_MA[2]_SDI, and AN[15]_FCK)
CIN_M
—
12
pF
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
13
Electrical Characteristics
Table 9. DC Electrical Specifications (TA = TL – TH) (continued)
Spec
Characteristic
Symbol
Min
Max.
Unit
27a Operating current 1.5 V supplies @ 82 MHz: 6, 7
VDD (including VDDF max current) @1.65 V high use 8, 9, 10, 11, 12
VDD (including VDDF max current) @1.35 V high use 8, 9, 10, 11, 12
IDD
IDD
—
—
250
180
mA
mA
27b Operating current 1.5 V supplies @ 68 MHz: 13, 14
VDD (including VDDF max current) @1.65 V high use15, 16, 17
VDD (including VDDF max current) @1.35 V high use 15, 16, 17
IDD
IDD
—
—
210
160
mA
mA
27c Operating current 1.5 V supplies @ 42 MHz: 13, 14
VDD (including VDDF max current) @1.65 V high use 15, 16, 17
VDD (including VDDF max current) @1.35 V high use 15, 16, 17
IDD
IDD
—
—
130
110
mA
mA
IDD_STBY
IDD_STBY
IDD_STBY
—
—
—
20
30
50
μA
μA
μA
IDD_STBY @ 60o C
VSTBY @ 0.8 V
VSTBY @ 1.0 V
VSTBY @ 1.2 V
IDD_STBY
IDD_STBY
IDD_STBY
—
—
—
70
100
200
μA
μA
μA
IDD_STBY @ 150o C (Tj)
VSTBY @ 0.8 V
VSTBY @ 1.0 V
VSTBY @ 1.2 V
IDD_STBY
IDD_STBY
IDD_STBY
—
—
—
1200
1500
2000
μA
μA
μA
VDD33 19
IDD_33
—
2 + (values
derived from
procedure of
footnote 19)
mA
VFLASH
IVFLASH
—
10
mA
VDDSYN
IDDSYN
—
15
mA
Operating current 5.0 V supplies (12 MHz ADCLK):
VDDA (VDDA0 + VDDA1)
Analog reference supply current (VRH, VRL)
VPP
IDD_A
IREF
IPP
—
—
—
20.0
1.0
25.0
mA
mA
mA
Operating current VDDE supplies: 20
VDDEH1
VDDE2
VDDE3
VDDEH4
VDDE5
VDDEH6
VDDE7
VDDEH8
VDDEH9
IDD1
IDD2
IDD3
IDD4
IDD5
IDD6
IDD7
IDD8
IDD9
—
—
—
—
—
—
—
—
—
Refer to
Footnote 20
mA
mA
mA
mA
mA
mA
mA
mA
mA
27d Refer to Figure 3 for an interpolation of this data.18
IDD_STBY @ 25o C
VSTBY @ 0.8 V
VSTBY @ 1.0 V
VSTBY @ 1.2 V
28
29
30
Operating current 3.3 V supplies @ fMAX MHz
MPC5533 Microcontroller Data Sheet, Rev. 0.0
14
Freescale Semiconductor
Electrical Characteristics
Table 9. DC Electrical Specifications (TA = TL – TH) (continued)
Spec
31
Characteristic
Min
Max.
Unit
10
20
20
110
130
170
μA
μA
μA
10
20
20
100
130
170
μA
μA
μA
IACT_S
10
20
150
170
μA
μA
IINACT_D
–2.5
2.5
μA
IIC
–2.0
2.0
mA
IINACT_A
–150
150
nA
IINACT_AD
–2.5
2.5
μA
VSS – VSSA
–100
100
mV
VRL
VSSA – 0.1
VSSA + 0.1
V
VRL – VSSA
–100
100
mV
VRH
VDDA – 0.1
VDDA + 0.1
V
VRH – VRL
4.5
5.25
V
Fast I/O weak pullup current 21
1.62–1.98 V
2.25–2.75 V
3.00–3.60 V
IACT_F
Fast I/O weak pulldown current 21
1.62–1.98 V
2.25–2.75 V
3.00–3.60 V
32
Symbol
Slow and medium I/O weak pullup/down current 21
3.0–3.6 V
4.5–5.5 V
33
I/O input leakage current 22
34
DC injection current (per pin)
35
Analog input current, channel off 23
35a Analog input current, shared analog / digital pins
(AN[12], AN[13], AN[14], AN[15])
36
VSS to VSSA differential voltage 24
37
Analog reference low voltage
38
VRL differential voltage
39
Analog reference high voltage
40
VREF differential voltage
41
VSSSYN to VSS differential voltage
VSSSYN – VSS
–50
50
mV
42
VRCVSS to VSS differential voltage
VRCVSS – VSS
–50
50
mV
43
VDDF to VDD differential voltage
VDDF – VDD
–100
100
mV
43a VRC33 to VDDSYN differential voltage
VRC33 – VDDSYN
–0.1
0.1 25
V
VIDIFF
–2.5
2.5
V
TA = (TL to TH)
TL
TH
οC
—
—
50
V/ms
44
Analog input differential signal range (with common mode 2.5 V)
45
Operating temperature range, ambient (packaged)
46
Slew rate on power-supply pins
1
VDDE2 and VDDE3 are limited to 2.25–3.6 V only if EBTS = 0; VDDE2 and VDDE3 have a range of 1.6–3.6 V if EBTS = 1.
| VDDA0 – VDDA1 | must be < 0.1 V.
3
VPP can drop to 3.0 V during read operations.
4 If standby operation is not required, connect V
STBY to ground.
5
Applies to CLKOUT, external bus pins, and Nexus pins.
6
Maximum average RMS DC current.
7 Figure 3 shows an illustration of the I
DD_STBY values interpolated for these temperature values.
8
Average current measured on Automotive benchmark.
9
Peak currents can be higher on specialized code.
10 High use current measured while running optimized SPE assembly code with all channels of the eTPU running autonomously, plus
the eDMA transferring data continuously from SRAM to SRAM.
2
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
15
Electrical Characteristics
11
Power requirements for the VDD33 supply depend on the frequency of operation, load of all I/O pins, and the voltages on the I/O
segments. Refer to Table 11 for values to calculate power dissipation for specific operation.
12
Power requirements for each I/O segment are dependent on the frequency of operation and load of the I/O pins on a particular I/O
segment, and the voltage of the I/O segment. Refer to Table 10 for values to calculate power dissipation for specific operation. The
total power consumption of an I/O segment is the sum of the individual power consumptions for each pin on the segment.
13
Maximum average RMS DC current.
14
Figure 3 shows an illustration of the IDD_STBY values interpolated for these temperature values.
15
Average current measured on automotive benchmark.
16
Peak currents can be higher on specialized code.
17
High use current measured while running optimized SPE assembly code with all channels of the eTPU running autonomously, plus
the eDMA transferring data continuously from SRAM to SRAM.
18
Figure 3 shows an illustration of the IDD_STBY values interpolated for these temperature values.
19
Power requirements for the VDD33 supply depend on the frequency of operation, load of all I/O pins, and the voltages on the I/O
segments. Refer to Table 11 for values to calculate the power dissipation for a specific operation.
20
Power requirements for each I/O segment are dependent on the frequency of operation and load of the I/O pins on a particular I/O
segment, and the voltage of the I/O segment. Refer to Table 10 for values to calculate power dissipation for specific operation. The
total power consumption of an I/O segment is the sum of the individual power consumptions for each pin on the segment.
21 Absolute value of current, measured at V and V .
IL
IH
22 Weak pullup/down inactive. Measured at V
DDE = 3.6 V and VDDEH = 5.25 V. Applies to pad types: pad_fc, pad_sh, and pad_mh.
23 Maximum leakage occurs at maximum operating temperature. Leakage current decreases by approximately one-half for each 8 oC
to 12 oC, in the ambient temperature range of 50 oC to 125 oC. Applies to pad types: pad_a and pad_ae.
24 V
SSA refers to both VSSA0 and VSSA1. | VSSA0 – VSSA1 | must be < 0.1 V.
25 Up to 0.6 V during power up and power down.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
16
Freescale Semiconductor
Electrical Characteristics
Figure 3 shows an approximate interpolation of the ISTBY worst-case specification to estimate values at
different voltages and temperatures. The vertical lines shown at 25 οC, 60 οC, and 150 οC in Figure 3 are
the IDD_STBY specifications (27d) listed in Table 9.
Istby vs. Junction Tem p
2000
1900
1800
1700
1600
1500
1400
1300
µA
uA
1200
1100
0.8V
1000
900
800
1.0V
1.2V
700
600
500
400
300
200
100
0
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
Tem p (C)
Figure 3. ISTBY Worst-case Specifications
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
17
Electrical Characteristics
3.8.1
I/O Pad Current Specifications
The power consumption of an I/O segment depends on the usage of the pins on a particular segment. The
power consumption is the sum of all output pin currents for a segment. The output pin current can be
calculated from Table 10 based on the voltage, frequency, and load on the pin. Use linear scaling to
calculate pin currents for voltage, frequency, and load parameters that fall outside the values given in
Table 10.
Table 10. I/O Pad Average DC Current (TA = TL – TH)1
Spec
Pad Type
Symbol
1
2
Frequency
(MHz)
Load2 (pF)
Voltage (V)
Drive Select /
Slew Rate
Control Setting
Current (mA)
25
50
5.25
11
8.0
10
50
5.25
01
3.2
2
50
5.25
00
0.7
4
2
200
5.25
00
2.4
5
50
50
5.25
11
17.3
3
6
Slow
IDRV_SH
20
50
5.25
01
6.5
3.33
50
5.25
00
1.1
8
3.33
200
5.25
00
3.9
9
66
10
3.6
00
2.8
10
66
20
3.6
01
5.2
11
66
30
3.6
10
8.5
12
66
50
3.6
11
11.0
13
66
10
1.98
00
1.6
14
66
20
1.98
01
2.9
15
66
30
1.98
10
4.2
16
66
50
1.98
11
6.7
17
56
10
3.6
00
2.4
18
56
20
3.6
01
4.4
19
56
30
3.6
10
7.2
7
20
Medium
IDRV_MH
56
50
3.6
11
9.3
56
10
1.98
00
1.3
22
56
20
1.98
01
2.5
23
56
30
1.98
10
3.5
24
56
50
1.98
11
5.7
25
40
10
3.6
00
1.7
26
40
20
3.6
01
3.1
27
40
30
3.6
10
5.1
21
Fast
IDRV_FC
28
40
50
3.6
11
6.6
29
40
10
1.98
00
1.0
30
40
20
1.98
01
1.8
31
40
30
1.98
10
2.5
32
40
50
1.98
11
4.0
1
These values are estimates from simulation and are not tested. Currents apply to output pins only.
2
All loads are lumped.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
18
Freescale Semiconductor
Electrical Characteristics
3.8.2
I/O Pad VDD33 Current Specifications
The power consumption of the VDD33 supply dependents on the usage of the pins on all I/O segments. The
power consumption is the sum of all input and output pin VDD33 currents for all I/O segments. The output
pin VDD33 current can be calculated from Table 11 based on the voltage, frequency, and load on all fast
(pad_fc) pins. The input pin VDD33 current can be calculated from Table 11 based on the voltage,
frequency, and load on all pad_sh and pad_mh pins. Use linear scaling to calculate pin currents for voltage,
frequency, and load parameters that fall outside the values given in Table 11.
Table 11. VDD33 Pad Average DC Current (TA = TL – TH) 1
Spec
Pad Type
Symbol
Frequency
(MHz)
Load 2
(pF)
VDD33
(V)
VDDE
(V)
Drive
Select
Current
(mA)
Inputs
1
Slow
I33_SH
66
0.5
3.6
5.5
NA
0.003
2
Medium
I33_MH
66
0.5
3.6
5.5
NA
0.003
3
66
10
3.6
3.6
00
0.35
4
66
20
3.6
3.6
01
0.53
5
66
30
3.6
3.6
10
0.62
Outputs
6
66
50
3.6
3.6
11
0.79
7
66
10
3.6
1.98
00
0.35
8
66
20
3.6
1.98
01
0.44
9
66
30
3.6
1.98
10
0.53
10
66
50
3.6
1.98
11
0.70
11
56
10
3.6
3.6
00
0.30
12
56
20
3.6
3.6
01
0.45
13
56
30
3.6
3.6
10
0.52
14
56
50
3.6
3.6
11
0.67
56
10
3.6
1.98
00
0.30
16
56
20
3.6
1.98
01
0.37
17
56
30
3.6
1.98
10
0.45
15
Fast
I33_FC
18
56
50
3.6
1.98
11
0.60
19
40
10
3.6
3.6
00
0.21
20
40
20
3.6
3.6
01
0.31
21
40
30
3.6
3.6
10
0.37
22
40
50
3.6
3.6
11
0.48
23
40
10
3.6
1.98
00
0.21
24
40
20
3.6
1.98
01
0.27
25
40
30
3.6
1.98
10
0.32
26
40
50
3.6
1.98
11
0.42
1
These values are estimated from simulation and not tested. Currents apply to output pins for the fast pads only and to input
pins for the slow and medium pads only.
2
All loads are lumped.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
19
Electrical Characteristics
3.9
Oscillator and FMPLL Electrical Characteristics
Table 12. FMPLL Electrical Specifications
(VDDSYN = 3.0–3.6 V; VSS = VSSSYN = 0.0 V; TA = TL to TH)
Spec
Characteristic
Symbol
Minimum
Maximum
1
PLL reference frequency range: 1
Crystal reference
External reference
Dual controller (1:1 mode)
fref_crystal
fref_ext
fref_1:1
8
8
24
20
20
fsys ÷ 2
2
System frequency 2
fsys
fICO(MIN) ÷ 2RFD
fMAX 3
MHz
3
System clock period
tCYC
—
1 ÷ fsys
ns
4
Loss of reference frequency 4
fLOR
100
1000
kHz
5
Self-clocked mode (SCM) frequency 5
fSCM
7.4
17.5
MHz
EXTAL input high voltage crystal mode 6
VIHEXT
VXTAL + 0.4 V
—
V
All other modes
[dual controller (1:1), bypass, external reference]
VIHEXT
(VDDE5 ÷ 2) + 0.4 V
—
V
EXTAL input low voltage crystal mode 7
VILEXT
—
VXTAL – 0.4 V
V
All other modes
[dual controller (1:1), bypass, external reference]
VILEXT
—
(VDDE5 ÷ 2) – 0.4 V
V
IXTAL
0.8
3
mA
6
7
Unit
MHz
8
XTAL current 8
9
Total on-chip stray capacitance on XTAL
CS_XTAL
—
1.5
pF
10
Total on-chip stray capacitance on EXTAL
CS_EXTAL
—
1.5
pF
11
Crystal manufacturer’s recommended capacitive
load
CL
Refer to crystal
specification
Refer to crystal
specification
pF
Discrete load capacitance to connect to EXTAL
CL_EXTAL
—
(2 × CL) – CS_EXTAL
– CPCB_EXTAL 9
pF
Discrete load capacitance to connect to XTAL
CL_XTAL
—
(2 × CL) – CS_XTAL
– CPCB_XTAL 9
pF
tlpll
—
750
μs
tskew
–2
2
ns
12
13
14
PLL lock time 10
15
Dual controller (1:1) clock skew
(between CLKOUT and EXTAL) 11, 12
16
Duty cycle of reference
tDC
40
60
%
17
Frequency unLOCK range
fUL
–4.0
4.0
% fSYS
18
Frequency LOCK range
fLCK
–2.0
2.0
% fSYS
MPC5533 Microcontroller Data Sheet, Rev. 0.0
20
Freescale Semiconductor
Electrical Characteristics
Table 12. FMPLL Electrical Specifications (continued)
(VDDSYN = 3.0–3.6 V; VSS = VSSSYN = 0.0 V; TA = TL to TH)
Spec
Characteristic
Symbol
Minimum
Maximum
CJITTER
19
CLKOUT period jitter, measured at fSYS max: 13, 14
Peak-to-peak jitter (clock edge to clock edge)
Long term jitter (averaged over a 2 ms interval)
20
Frequency modulation range limit 15
(do not exceed fsys maximum)
21
ICO frequency
fico = [ fref_crystal × (MFD + 4) ] ÷ (PREDIV + 1) 16
fico = [ fref_ext × (MFD + 4) ] ÷ (PREDIV + 1)
22
Predivider output frequency (to PLL)
Unit
—
—
5.0
0.01
CMOD
0.8
2.4
%fSYS
fico
48
8017
MHz
fPREDIV
4
20 18
MHz
%
fCLKOUT
1
Nominal crystal and external reference values are worst-case not more than 1%. The device operates correctly if the frequency
remains within ± 5% of the specification limit. This tolerance range allows for a slight frequency drift of the crystals over time.
The designer must thoroughly understand the drift margin of the source clock.
2 All internal registers retain data at 0 Hz.
3 Up to the maximum frequency rating of the device (refer to Table 1).
4 Loss of reference frequency is defined as the reference frequency detected internally, which transitions the PLL into self-clocked
mode.
5 The PLL operates at self-clocked mode (SCM) frequency when the reference frequency falls below f
LOR. SCM frequency is
measured on the CLKOUT ball with the divider set to divide-by-two of the system clock.
NOTE: In SCM, the MFD and PREDIV have no effect and the RFD is bypassed.
6 Use the EXTAL input high voltage parameter when using the FlexCAN oscillator in crystal mode (no quartz crystals or
resonators). (Vextal – Vxtal) must be ≥ 400 mV for the oscillator’s comparator to produce the output clock.
7 Use the EXTAL input low voltage parameter when using the FlexCAN oscillator in crystal mode (no quartz crystals or
resonators). (Vxtal – Vextal) must be ≥ 400 mV for the oscillator’s comparator to produce the output clock.
8 I
xtal is the oscillator bias current out of the XTAL pin with both EXTAL and XTAL pins grounded.
9 C
PCB_EXTAL and CPCB_XTAL are the measured PCB stray capacitances on EXTAL and XTAL, respectively.
10 This specification applies to the period required for the PLL to relock after changing the MFD frequency control bits in the
synthesizer control register (SYNCR). From power up with crystal oscillator reference, the lock time also includes the crystal
startup time.
11 PLL is operating in 1:1 PLL mode.
12 V
DDE = 3.0–3.6 V.
13 Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum f .
sys
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise
injected into the PLL circuitry via VDDSYN and VSSSYN and variation in crystal oscillator frequency increase the jitter percentage
for a given interval. CLKOUT divider is set to divide-by-two.
14 Values are with frequency modulation disabled. If frequency modulation is enabled, jitter is the sum of (jitter + Cmod).
15 Modulation depth selected must not result in f
sys value greater than the fsys maximum specified value.
RFD)
sys = fico ÷ (2
16 f
17
The ICO frequency can be higher than the maximum allowable system frequency. For this case, set the FMPLL synthesizer
control register reduced frequency divider (FMPLL_SYNCR[RFD]) to divide-by-two (RFD = 0b001). Therefore, for a 40 MHz
maximum device (system frequency), program the FMPLL to generate 80 MHz at the ICO output and then divide-by-two the
RFD to provide the 40 MHz clock.
18 Maximum value for dual controller (1:1) mode is (f
MAX ÷ 2) with the predivider set to 1 (FMPLL_SYNCR[PREDIV] = 0b001).
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
21
Electrical Characteristics
3.10
eQADC Electrical Characteristics
Table 13. eQADC Conversion Specifications (TA = TL to TH)
Spec
Characteristic
Symbol
Minimum
Maximum
Unit
FADCLK
1
12
MHz
13 + 2 (15)
14 + 2 (16)
13 + 128 (141)
14 + 128 (142)
1
ADC clock (ADCLK) frequency 1
Conversion cycles
Differential
Single ended
CC
2
3
Stop mode recovery time 2
TSR
10
—
μs
—
1.25
—
mV
3
ADCLK
cycles
4
Resolution
5
INL: 6 MHz ADC clock
INL6
–4
4
Counts 3
6
INL: 12 MHz ADC clock
INL12
–8
7
8
9
10
DNL: 6 MHz ADC clock
DNL: 12 MHz ADC clock
Offset error with calibration
Full-scale gain error with calibration
7, 8, 9, 10
8
Counts
DNL6
–3
4
34
Counts
DNL12
–6 4
6
4
Counts
OFFWC
–4 5
4
5
Counts
GAINWC
–8 6
8
6
Counts
IINJ
–1
1
mA
11
Disruptive input injection current
12
Incremental error due to injection current. All channels are
10 kΩ < Rs <100 kΩ
Channel under test has Rs = 10 kΩ,
IINJ = IINJMAX, IINJMIN
EINJ
–4
4
Counts
13
Total unadjusted error (TUE) for single ended conversions
with calibration 11, 12, 13, 14, 15
TUE
–4
4
Counts
1
Conversion characteristics vary with FADCLK rate. Reduced conversion accuracy occurs at maximum FADCLK rate. The
maximum value is based on 800 KS/s and the minimum value is based on 20 MHz oscillator clock frequency divided by a
maximum 16 factor.
2
Stop mode recovery time begins when the ADC control register enable bits are set until the ADC is ready to perform
conversions.
3 At V
RH – VRL = 5.12 V, one least significant bit (LSB) = 1.25, mV = one count.
4
Guaranteed 10-bit mono tonicity.
5 The absolute value of the offset error without calibration ≤ 100 counts.
6 The absolute value of the full scale gain error without calibration ≤ 120 counts.
7 Below disruptive current conditions, the channel being stressed has conversion values of: 0x3FF for analog inputs greater than
VRH, and 0x000 for values less than VRL. This assumes that VRH ≤ VDDA and VRL ≥ VSSA due to the presence of the sample
amplifier. Other channels are not affected by non-disruptive conditions.
8 Exceeding the limit can cause a conversion error on both stressed and unstressed channels. Transitions within the limit do not
affect device reliability or cause permanent damage.
9 Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate
resistance values using VPOSCLAMP = VDDA + 0.5 V and VNEGCLAMP = – 0.3 V, then use the larger of the calculated values.
10 This condition applies to two adjacent pads on the internal pad.
11 The TUE specification is always less than the sum of the INL, DNL, offset, and gain errors due to canceling errors.
12
TUE does not apply to differential conversions.
13 Measured at 6 MHz ADC clock. TUE with a 12 MHz ADC clock is: –16 counts < TUE < 16 counts.
14 TUE includes all internal device errors such as internal reference variation (75% Ref, 25% Ref).
15
Depending on the input impedance, the analog input leakage current (Table 9. DC Electrical Specifications, spec 35a) can
affect the actual TUE measured on analog channels AN[12], AN[13], AN[14], AN[15].
MPC5533 Microcontroller Data Sheet, Rev. 0.0
22
Freescale Semiconductor
Electrical Characteristics
3.11
Spec
Table 14. Flash Program and Erase Specifications (TA = TL to TH)
Spec
3
1
2
3
4
5
6
H7Fb Flash Memory Electrical Characteristics
Flash Program Characteristic
Doubleword (64 bits) program time 4
Symbol
Min.
Typical 1
Initial
Max. 2
Max. 3
Unit
Tdwprogram
—
10
—
500
μs
500
μs
4
Page program time
4
5
Tpprogram
—
22
44
7
16 KB block pre-program and erase time
T16kpperase
—
325
525
5000
ms
9
48 KB block pre-program and erase time
T48kpperase
—
435
525
5000
ms
10
64 KB block pre-program and erase time
T64kpperase
—
525
675
5000
ms
8
128 KB block pre-program and erase time
T128kpperase
—
675
1800
7500
ms
11
Minimum operating frequency for program and erase
operations 6
—
25
—
—
—
MHz
Typical program and erase times are calculated at 25 oC operating temperature using nominal supply values.
Initial factory condition: ≤ 100 program/erase cycles, 25 oC, using a typical supply voltage measured at a minimum system
frequency of 80 MHz.
The maximum erase time occurs after the specified number of program/erase cycles. This maximum value is characterized
but not guaranteed.
Actual hardware programming times. This does not include software overhead.
Page size is 128 bits (4 words).
The read frequency of the flash can range up to the maximum operating frequency. There is no minimum read frequency
condition.
Table 15. Flash EEPROM Module Life (TA = TL to TH)
Spec
1
Characteristic
Symbol
Min.
Typical 1
Unit
1a
Number of program/erase cycles per block for 16 KB, 48 KB, and
64 KB blocks over the operating temperature range (TJ)
P/E
100,000
—
cycles
1b
Number of program/erase cycles per block for 128 KB blocks over the
operating temperature range (TJ)
P/E
1000
100,000
cycles
2
Data retention
Blocks with 0–1,000 P/E cycles
Blocks with 1,001–100,000 P/E cycles
20
5
—
—
years
Retention
Typical endurance is evaluated at 25o C. Product qualification is performed to the minimum specification. For additional
information on the Freescale definition of typical endurance, refer to engineering bulletin EB619 Typical Endurance for
Nonvolatile Memory.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
23
Electrical Characteristics
Table 16 shows the FLASH_BIU settings versus frequency of operation. Refer to the device reference
manual for definitions of these bit fields.
Table 16. FLASH_BIU Settings vs. Frequency of Operation1
Target Maximum Frequency (MHz)
PFLIM 3
BFEN 2
0b0
0b1
0b000
to
0b010
0b0
0b1
0b0
0b1
0b0
0b1
0b000
to
0b010
0b0
0b1
0b01
0b0
0b1
0b0
0b1
0b000
to
0b010
0b0
0b1
0b011
0b01
0b0
0b1
0b0
0b1
0b000
to
0b010
0b0
0b1
0b111
0b11
0b0
0b0
0b000
0b0
DPFEN 2
APC
RWSC
WWSC
Up to and including 27 MHz 4, 5
0b000
0b000
0b01
0b0
0b1
Up to and including 52 MHz 6
0b001
0b001
0b01
Up to and including 77 MHz 7
0b010
0b010
Up to and including 82 MHz 8
0b011
Reset values:
0b111
1
2
3
4
5
6
7
8
IPFEN 2
Illegal combinations exist. Use entries from the same row in this table.
For maximum flash performance, set to 0b1.
For maximum flash performance, set to 0b010.
27 MHz parts allow for 25 MHz system clock + 2% frequency modulation (FM).
The APC, RWSC, and WWSC combination requires setting the PRD bit to 1 in the flash MCR register.
52 MHz parts allow for 50 MHz system clock + 2% FM.
77 MHz parts allow for 75 MHz system clock + 2% FM.
82 MHz parts allow for 80 MHz system clock + 2% FM.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
24
Freescale Semiconductor
Electrical Characteristics
3.12
3.12.1
AC Specifications
Pad AC Specifications
Table 17. Pad AC Specifications (VDDEH = 5.0 V, VDDE = 1.8 V) 1
Spec
SRC / DSC
(binary)
Pad
11
1
Slow high voltage (SH)
01
00
11
2
Medium high voltage (MH)
01
00
Out Delay 2, 3, 4
(ns)
Rise / Fall 4, 5
(ns)
Load Drive
(pF)
26
15
50
82
60
200
75
40
50
137
80
200
377
200
50
476
260
200
16
8
50
43
30
200
34
15
50
61
35
200
192
100
50
239
125
200
2.7
10
2.5
20
2.4
30
2.3
50
00
3
01
Fast
10
3.1
11
1
2
3
4
5
4
Pullup/down (3.6 V max)
—
—
7500
50
5
Pullup/down (5.5 V max)
—
—
9000
50
These are worst-case values that are estimated from simulation (not tested). The values in the table are simulated at:
VDD = 1.35–1.65 V; VDDE = 1.62–1.98 V; VDDEH = 4.5–5.25 V; VDD33 and VDDSYN = 3.0–3.6 V; and TA = TL to TH.
This parameter is supplied for reference and is guaranteed by design (not tested).
The output delay is shown in Figure 4. To calculate the output delay with respect to the system clock,
add a maximum of one system clock to the output delay.
The output delay and rise and fall are measured to 20% or 80% of the respective signal.
This parameter is guaranteed by characterization rather than 100% tested.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
25
Electrical Characteristics
Table 18. Derated Pad AC Specifications (VDDEH = 3.3 V, VDDE = 3.3 V) 1
Spec
SRC/DSC
(binary)
Pad
11
1
Slow high voltage (SH)
01
00
11
2
Medium high voltage (MH)
01
00
Out Delay 2, 3, 4
(ns)
Rise / Fall 3, 5
(ns)
Load Drive
(pF)
39
23
50
120
87
200
101
52
50
188
111
200
507
248
50
597
312
200
23
12
50
64
44
200
50
22
50
90
50
200
261
123
50
305
156
200
2.4
10
2.2
20
2.1
30
2.1
50
00
3
01
Fast
10
3.2
11
1
2
3
4
5
4
Pullup/down (3.6 V max)
—
—
7500
50
5
Pullup/down (5.5 V max)
—
—
9500
50
These are worst-case values that are estimated from simulation (not tested). The values in the table are simulated at:
VDD = 1.35–1.65 V; VDDE = 3.0–3.6 V; VDDEH = 3.0–3.6 V; VDD33 and VDDSYN = 3.0–3.6 V; and TA = TL to TH.
This parameter is supplied for reference and guaranteed by design (not tested).
The output delay, and the rise and fall, are calculated to 20% or 80% of the respective signal.
The output delay is shown in Figure 4. To calculate the output delay with respect to the system clock, add a maximum of one
system clock to the output delay.
This parameter is guaranteed by characterization rather than 100% tested.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
26
Freescale Semiconductor
Electrical Characteristics
VDD ÷ 2
Pad
internal data
input signal
Rising-edge
out delay
Falling-edge
out delay
VOH
Pad
output
VOL
Figure 4. Pad Output Delay
3.13
AC Timing
3.13.1
Reset and Configuration Pin Timing
Table 19. Reset and Configuration Pin Timing 1
Spec
1
Characteristic
Symbol
Min.
Max.
Unit
1
RESET pulse width
tRPW
10
—
tCYC
2
RESET glitch detect pulse width
tGPW
2
—
tCYC
3
PLLCFG, BOOTCFG, WKPCFG, RSTCFG setup time to RSTOUT valid
tRCSU
10
—
tCYC
4
PLLCFG, BOOTCFG, WKPCFG, RSTCFG hold time from RSTOUT valid
tRCH
0
—
tCYC
Reset timing specified at: VDDEH = 3.0–5.25 V and TA = TL to TH.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
27
Electrical Characteristics
2
RESET
1
RSTOUT
3
PLLCFG
BOOTCFG
RSTCFG
WKPCFG
4
Figure 5. Reset and Configuration Pin Timing
3.13.2
IEEE 1149.1 Interface Timing
Table 20. JTAG Pin AC Electrical Characteristics 1
Spec
1
Characteristic
Symbol
Min.
Max.
Unit
1
TCK cycle time
tJCYC
100
—
ns
2
TCK clock pulse width (measured at VDDE ÷ 2)
tJDC
40
60
ns
3
TCK rise and fall times (40% to 70%)
tTCKRISE
—
3
ns
4
TMS, TDI data setup time
tTMSS, tTDIS
5
—
ns
5
TMS, TDI data hold time
tTMSH, tTDIH
25
—
ns
6
TCK low to TDO data valid
tTDOV
—
20
ns
7
TCK low to TDO data invalid
tTDOI
0
—
ns
8
TCK low to TDO high impedance
tTDOHZ
—
20
ns
9
JCOMP assertion time
tJCMPPW
100
—
ns
10
JCOMP setup time to TCK low
tJCMPS
40
—
ns
11
TCK falling-edge to output valid
tBSDV
—
50
ns
12
TCK falling-edge to output valid out of high impedance
tBSDVZ
—
50
ns
13
TCK falling-edge to output high impedance (Hi-Z)
tBSDHZ
—
50
ns
14
Boundary scan input valid to TCK rising-edge
tBSDST
50
—
ns
15
TCK rising-edge to boundary scan input invalid
tBSDHT
50
—
ns
These specifications apply to JTAG boundary scan only. JTAG timing specified at: VDDE = 3.0–3.6 V and TA = TL to TH.
Refer to Table 21 for Nexus specifications.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
28
Freescale Semiconductor
Electrical Characteristics
TCK
2
3
2
1
3
Figure 6. JTAG Test Clock Input Timing
TCK
4
5
TMS, TDI
6
7
8
TDO
Figure 7. JTAG Test Access Port Timing
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
29
Electrical Characteristics
TCK
10
JCOMP
9
Figure 8. JTAG JCOMP Timing
MPC5533 Microcontroller Data Sheet, Rev. 0.0
30
Freescale Semiconductor
Electrical Characteristics
TCK
11
13
Output
signals
12
Output
signals
14
15
Input
signals
Figure 9. JTAG Boundary Scan Timing
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
31
Electrical Characteristics
3.13.3
Nexus Timing
Table 21. Nexus Debug Port Timing 1
Spec
Characteristic
1
MCKO cycle time
2
MCKO duty cycle
3
4
MCKO low to MDO data valid
3
MCKO low to MSEO data valid
3
3
Symbol
Min.
Max.
Unit
tMCYC
12
8
tCYC
tMDC
40
60
%
tMDOV
–1.5
3.0
ns
tMSEOV
–1.5
3.0
ns
tEVTOV
–1.5
3.0
ns
5
MCKO low to EVTO data valid
6
EVTI pulse width
tEVTIPW
4.0
—
tTCYC
7
EVTO pulse width
tEVTOPW
1
4
9
TCK duty cycle
tTDC
40
60
%
10
TDI, TMS data setup time
tNTDIS, tNTMSS
8
—
ns
11
TDI, TMS data hold time
tNTDIH, tNTMSH
5
—
ns
0
12
ns
0
10
ns
—
—
—
13
3
5
tCYC
tTCYC
tJOV
VDDE = 2.25–3.0 V
VDDE = 3.0–3.6 V
4
—
TCK cycle time
12
2
tMCYC
8
TCK low to TDO data valid
1
—
4
RDY valid to MCKO
5
—
JTAG specifications apply when used for debug functionality. All Nexus timing relative to MCKO is measured from 50% of
MCKO and 50% of the respective signal. Nexus timing specified at VDD = 1.35–1.65 V, VDDE = 2.25–3.6 V,
VDD33 and VDDSYN = 3.0–3.6 V, TA = TL to TH, and CL = 30 pF with DSC = 0b10.
The Nexus AUX port runs up to 82 MHz.
MDO, MSEO, and EVTO data is held valid until the next MCKO low cycle occurs.
Limit the maximum frequency to approximately 16 MHz (VDDE = 2.25–3.0 V) or 20 MHz (VDDE = 3.0–3.6 V) to meet the timing
specification for tJOV of [0.2 x tJCYC] as outlined in the IEEE-ISTO 5001-2003 specification.
The RDY pin timing is asynchronous to MCKO and is guaranteed by design to function correctly.
1
2
MCKO
4
3
5
MDO
MSEO
EVTO
Output Data Valid
Figure 10. Nexus Output Timing
MPC5533 Microcontroller Data Sheet, Rev. 0.0
32
Freescale Semiconductor
Electrical Characteristics
TCK
10
11
TMS, TDI
12
TDO
Figure 11. Nexus TDI, TMS, TDO Timing
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
33
Electrical Characteristics
3.13.4
External Bus Interface (EBI) Timing
Table 22 lists the timing information for the external bus interface (EBI).
Table 22. External Bus Operation Timing1, 2
Spec
Characteristic
and
Description
1
CLKOUT period
2
CLKOUT duty cycle
3
4
CLKOUT rise time
CLKOUT fall time
CLKOUT positive edge to
output signal invalid or
Hi-Z (hold time)
External Bus Frequency 3
Symbol
20 MHz
33 MHz
40 MHz
Unit
Notes
Signals are measured at
50% VDDE.
Min.
Max
Min.
Max
Min.
Max
TC
24.4
—
17.5
—
14.9
—
ns
tCDC
45%
55%
45%
55%
45%
55%
TC
tCRT
—
tCFT
—
tCOH
1.06
4
—
4
—
—
—
—
4
—
1.06
ns
—
4
ns
—
ns
—
—
1.06
EBTS = 0
—
—
1.5
—
4
1.5
1.5
EBTS = 1
External bus interface
CS[0:3]
5 ADDR[8:31]
5
DATA[0:15]
RD_WR
BDIP
WE/BE[0:1]
OE
TS
TA
CLKOUT positive edge to
output signal valid
(output delay)
Hold time selectable via
SIU_ECCR
[EBTS] bit.
10.06
tCOV
10.06
—
—
11.0
10.06
11.0
EBTS = 0
ns
—
11.0
EBTS = 1
Output valid time
selectable via
SIU_ECCR
[EBTS] bit.
External bus interface
CS[0:3]
5 ADDR[8:31]
6
DATA[0:15]
RD_WR
BDIP
WE/BE[0:1]
OE
TS
TA
MPC5533 Microcontroller Data Sheet, Rev. 0.0
34
Freescale Semiconductor
Electrical Characteristics
Table 22. External Bus Operation Timing1, 2 (continued)
External Bus Frequency 3
Characteristic
and
Description
Spec
20 MHz
Symbol
33 MHz
40 MHz
Notes
Unit
Min.
Max
Min.
Max
Min.
Max
tCIS
10.0
—
10.0
—
10.0
—
ns
tCIH
1.0
—
1.0
—
1.0
—
ns
Input signal valid to
CLKOUT positive edge
(setup time)
75
External bus interface
ADDR[8:31]
DATA[0:15]
RD_WR
TS
TA
CLKOUT positive edge to
input signal invalid (hold
time)
85
1
2
3
4
5
6
External bus interface
ADDR[8:31]
DATA[0:15]
RD_WR
TS
TA
EBI timing specified at VDDE = 1.6–3.6 V (unless stated otherwise), TA = TL to TH, and CL = 30 pF with DSC = 0b10.
The external bus is limited to half the speed of the internal bus.
Speed is the nominal maximum frequency. Max speed is the maximum speed allowed including frequency modulation (FM).
42 MHz parts allow for 40 MHz system clock + 2% FM; 68 MHz parts allow for a 66 MHz system clock + 2% FM, and
82 MHz parts allow for 80 MHz system clock + 2% FM.
Refer to fast pad timing in Table 17 and Table 18 (different values for 1.8 V and 3.3 V).
Available on the 324 package only; not available on the 208 package.
EBTS = 0 timings are tested and valid at VDDE = 2.25–3.6 V only; EBTS = 1 timings are tested and valid at VDDE = 1.6–3.6 V.
3.13.5
External Interrupt Timing (IRQ Signals)
Table 23. External Interrupt Timing 1
Spec
Characteristic
1
IRQ pulse-width low
2
IRQ pulse-width high
3
IRQ edge-to-edge time
2
Symbol
Min.
Max.
Unit
tIPWL
3
—
tCYC
TIPWH
3
—
tCYC
tICYC
6
—
tCYC
1
IRQ timing specified at: VDDEH = 3.0–5.25 V and TA = TL to TH.
2 Applies when IRQ signals are configured for rising-edge or falling-edge events, but not both.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
35
Electrical Characteristics
IRQ
2
1
3
Figure 12. External Interrupt Timing
3.13.6
eTPU Timing
Table 24. eTPU Timing 1
Spec
1
2
1
2
Characteristic
eTPU input channel pulse width
eTPU output channel pulse width
Symbol
Min.
Max
Unit
tICPW
4
—
tCYC
—
tCYC
tOCPW
2
2
eTPU timing specified at: VDDEH = 3.0–5.25 V and TA = TL to TH.
This specification does not include the rise and fall times. When calculating the minimum eTPU pulse width, include the rise
and fall times defined in the slew rate control fields (SRC) of the pad configuration registers (PCR).
2
eTPU
output
eTPU input
and TCRCLK
1
Figure 13. eTPU Timing
MPC5533 Microcontroller Data Sheet, Rev. 0.0
36
Freescale Semiconductor
Electrical Characteristics
3.13.7
DSPI Timing
Table 25. DSPI Timing 1, 2
40 MHz
Spec
1
2
3
4
5
6
7
Characteristic
66 MHz
80 MHz
Symbol
Unit
Min.
Max
Min.
Max
Min.
Max
1
SCK cycle time 3, 4
tSCK
48.8 ns
5.8 ms
28.4 ns
3.5 ms
24.4 ns
2.9 ms
—
2
5
tCSC
46
—
26
—
22
—
ns
PCS to SCK delay
6
3
After SCK delay
tASC
45
—
25
—
21
—
ns
4
SCK duty cycle
tSDC
(tSCK ÷ 2)
– 2 ns
(tSCK ÷ 2)
+ 2 ns
(tSCK ÷ 2)
– 2 ns
(tSCK ÷ 2)
+ 2 ns
(tSCK ÷ 2)
– 2 ns
(tSCK ÷ 2)
+ 2 ns
ns
5
Slave access time
(SS active to SOUT driven)
tA
—
25
—
25
—
25
ns
6
Slave SOUT disable time
(SS inactive to SOUT Hi-Z, or
invalid)
tDIS
—
25
—
25
—
25
ns
7
PCSx to PCSS time
tPCSC
4
—
4
—
4
—
ns
8
PCSS to PCSx time
tPASC
5
—
5
—
5
—
ns
tSUI
9
Data setup time for inputs
Master (MTFE = 0)
Slave
Master (MTFE = 1, CPHA = 0)7
Master (MTFE = 1, CPHA = 1)
20
2
–4
20
—
—
—
—
20
2
6
20
—
—
—
—
20
2
8
20
—
—
—
—
ns
ns
ns
ns
tHI
10
Data hold time for inputs
Master (MTFE = 0)
Slave
Master (MTFE = 1, CPHA = 0)7
Master (MTFE = 1, CPHA = 1)
–4
7
45
–4
—
—
—
—
–4
7
25
–4
—
—
—
—
–4
7
21
–4
—
—
—
—
ns
ns
ns
ns
tSUO
11
Data valid (after SCK edge)
Master (MTFE = 0)
Slave
Master (MTFE = 1, CPHA = 0)
Master (MTFE = 1, CPHA = 1)
—
—
—
—
5
25
45
5
—
—
—
—
5
25
25
5
—
—
—
—
5
25
21
5
ns
ns
ns
ns
tHO
12
Data hold time for outputs
Master (MTFE = 0)
Slave
Master (MTFE = 1, CPHA = 0)
Master (MTFE = 1, CPHA = 1)
–5
5.5
8
–5
—
—
—
—
–5
5.5
4
–5
—
—
—
—
–5
5.5
3
–5
—
—
—
—
ns
ns
ns
ns
All DSPI timing specifications use the fastest slew rate (SRC = 0b11) on pad type M or MH. DSPI signals using pad types of
S or SH have an additional delay based on the slew rate. DSPI timing is specified at VDDEH = 3.0–5.25 V, TA = TL to TH, and
CL = 50 pF with SRC = 0b11.
Speed is the nominal maximum frequency. Max speed is the maximum speed allowed including frequency modulation (FM).
42 MHz parts allow for 40 MHz system clock + 2% FM; 68 MHz parts allow for a 66 MHz system clock + 2% FM, and
82 MHz parts allow for 80 MHz system clock + 2% FM.
The minimum SCK cycle time restricts the baud rate selection for the given system clock rate.
These numbers are calculated based on two MPC55xx devices communicating over a DSPI link.
The actual minimum SCK cycle time is limited by pad performance.
The maximum value is programmable in DSPI_CTARx[PSSCK] and DSPI_CTARx[CSSCK].
The maximum value is programmable in DSPI_CTARx[PASC] and DSPI_CTARx[ASC].
This number is calculated using the SMPL_PT field in DSPI_MCR set to 0b10.
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
37
Electrical Characteristics
2
3
PCSx
1
4
SCK output
(CPOL=0)
4
SCK output
(CPOL=1)
9
SIN
10
First data
Last data
Data
12
SOUT
First data
11
Data
Last data
Figure 14. DSPI Classic SPI Timing—Master, CPHA = 0
PCSx
SCK output
(CPOL=0)
10
SCK output
(CPOL=1)
9
SIN
Data
First data
12
SOUT
First data
Last data
11
Data
Last data
Figure 15. DSPI Classic SPI Timing—Master, CPHA = 1
MPC5533 Microcontroller Data Sheet, Rev. 0.0
38
Freescale Semiconductor
Electrical Characteristics
3
2
SS
1
4
SCK input
(CPOL=0)
4
SCK input
(CPOL=1)
5
First data
SOUT
9
6
Data
Last data
Data
Last data
10
First data
SIN
11
12
Figure 16. DSPI Classic SPI Timing—Slave, CPHA = 0
SS
SCK input
(CPOL=0)
SCK input
(CPOL=1)
11
5
12
SOUT
First data
9
SIN
Data
Last data
Data
Last data
6
10
First data
Figure 17. DSPI Classic SPI Timing—Slave, CPHA = 1
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
39
Electrical Characteristics
3
PCSx
4
1
2
SCK output
(CPOL=0)
4
SCK output
(CPOL=1)
9
SIN
10
First data
Last data
Data
12
SOUT
11
First data
Last data
Data
Figure 18. DSPI Modified Transfer Format Timing—Master, CPHA = 0
PCSx
SCK output
(CPOL=0)
SCK output
(CPOL=1)
10
9
SIN
First data
Data
12
SOUT
First data
Data
Last data
11
Last data
Figure 19. DSPI Modified Transfer Format Timing—Master, CPHA = 1
MPC5533 Microcontroller Data Sheet, Rev. 0.0
40
Freescale Semiconductor
Electrical Characteristics
3
2
SS
1
SCK input
(CPOL=0)
4
4
SCK input
(CPOL=1)
12
11
5
First data
SOUT
Data
Last data
10
9
Data
First data
SIN
6
Last data
Figure 20. DSPI Modified Transfer Format Timing—Slave, CPHA = 0
SS
SCK input
(CPOL=0)
SCK input
(CPOL=1)
11
5
6
12
First data
SOUT
9
Last data
Data
Last data
10
First data
SIN
Data
Figure 21. DSPI Modified Transfer Format Timing—Slave, CPHA = 1
7
8
PCSS
PCSx
Figure 22. DSPI PCS Strobe (PCSS) Timing
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
41
Electrical Characteristics
3.13.8
eQADC SSI Timing
Table 26. EQADC SSI Timing Characteristics
Spec
Rating
Symbol
Minimum
Typical
Maximum
Unit
tFCK
2
—
17
tSYS_CLK
2
FCK period (tFCK = 1 ÷ fFCK) 1, 2
3
Clock (FCK) high time
tFCKHT
tSYS_CLK − 6.5
—
9 × (tSYS_CLK + 6.5)
ns
4
Clock (FCK) low time
tFCKLT
tSYS_CLK − 6.5
—
8 × (tSYS_CLK + 6.5)
ns
5
SDS lead / lag time
tSDS_LL
–7.5
—
+7.5
ns
6
SDO lead / lag time
tSDO_LL
–7.5
—
+7.5
ns
7
EQADC data setup time (inputs)
tEQ_SU
22
—
—
ns
8
EQADC data hold time (inputs)
tEQ_HO
1
—
—
ns
1
SS timing specified at VDDEH = 3.0–5.25 V, TA = TL to TH, and CL = 25 pF with SRC = 0b11. Maximum operating frequency
varies depending on track delays, master pad delays, and slave pad delays.
2 FCK duty cycle is not 50% when it is generated through the division of the system clock by an odd number.
2
3
4
FCK
5
4
SDS
25th
6
SDO
1st (MSB)
5
2nd
26th
External device data sample at
FCK falling-edge
8
7
SDI
1st (MSB) 2nd
25th
26th
EQADC data sample at
FCK rising-edge
Figure 23. EQADC SSI Timing
MPC5533 Microcontroller Data Sheet, Rev. 0.0
42
Freescale Semiconductor
Mechanicals
4
Mechanicals
4.1
MPC5533 208 MAP BGA Pinout
Figure 24 is a pinout for the MPC5533 208 MAP BGA package.
NOTES
VDDEH10 and VDDEH6 are connected internally on the 208-ball package and
are listed as VDDEH6.
The MPC5500 devices are pin compatible for software portability and use
the primary function names to label the pins in the BGA diagram. Although
some devices do not support all the primary functions shown in the BGA
diagram, the muxed and GPIO signals on those pins remain available. See
the signals chapter in the device reference manual for the signal muxing.
1
2
3
4
A
VSS
AN9
AN11
B
VDD
VSS
AN38
AN21
C VSTBY
VDD
VSS
D VDD33
AN39
5
6
7
8
9
10
11
12
13
AN1
AN5
VRH
VRL
AN27
VSSA0
AN12
MDO2
MDO0 VDD33
VSS
A
AN0
AN4
REF
BYPC
AN22
AN25
AN28
VDDA0
AN13
MDO3
MDO1
VSS
VDD
B
AN17
AN34
AN16
AN3
AN7
AN23
AN32
AN33
AN14
AN15
VSS
MSEO0
TCK
C
VDD
VSS
AN18
AN2
AN6
AN24
AN30
AN31
AN35 VDDEH
9
VSS
TMS
EVTO
TEST
D
AN37
VDD
VDDE7
TDI
EVTI
AN36
VDDEH
6
TDO
VDDA1 VSSA1
14
15
16
E
ETPUA ETPUA
30
31
F
ETPUA ETPUA ETPUA
28
29
26
G
ETPUA ETPUA ETPUA ETPUA
24
27
25
21
VSS
VSS
VSS
VSS
SOUTB PCSB3
H
ETPUA ETPUA ETPUA ETPUA
18
23
22
17
VSS
VSS
VSS
VSS
PCSA3 PCSB4 PCSB2 PCSB1 H
J
ETPUA ETPUA ETPUA ETPUA
14
20
19
13
VSS
VSS
VSS
VSS
PCSB5 TXDA PCSA2 SCKB J
K
ETPUA ETPUA ETPUA VDDEH
1
16
15
7
VSS
VSS
VSS
VSS
CNTXC RXDA RSTOUT
L
ETPUA ETPUA ETPUA TCRCLK
12
11
6
A
TXDB CNRXC
M
ETPUA ETPUA ETPUA ETPUA
10
9
1
5
RXDB
PLL
CFG0
BOOT
CFG1
N
ETPUA ETPUA ETPUA
8
4
0
VSS
VDD
VDD33 EMIOS EMIOS VDDEH EMIOS EMIOS VDD33
4
12
2
10
21
VSS
VRC
CTL
PLL
CFG1
P
ETPUA ETPUA
3
2
VSS
VDD
GPIO
207
VDDE2
EMIOS EMIOS EMIOS EMIOS EMIOS CNTXA
16
17
6
8
22
VDD
VSS
VRC33
XTAL
P
GPIO
206
EMIOS EMIOS EMIOS EMIOS EMIOS EMIOS EMIOS CNRXA CNRXB
14
19
23
4
3
9
11
VDD
VSS
VDD
SYN
R
EMIOS EMIOS EMIOS EMIOS EMIOS EMIOS EMIOS EMIOS CNTXB VDDE5
15
18
20
0
1
5
7
13
ENG
CLK
VDD
VSS
T
14
15
16
R
CS0
VSS
VDD
T
VSS
VDD
OE
1
2
3
4
5
6
7
8
9
10
11
12
13
MSEO1 E
MCKO JCOMP F
SINB
WKP
CFG
PCSB0 G
VPP
K
RESET L
VSS
SYN
M
EXTAL N
Figure 24. MPC5533 208 Package
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
43
Mechanicals
4.2
MPC5533 324 PBGA Pinout
Figure 25 is a pinout for the MPC5533 324 PBGA package.
NOTE
The MPC5500 devices are pin compatible for software portability and use
the primary function names to label the pins in the BGA diagram. Although
some devices do not support all the primary functions shown in the BGA
diagram, the muxed and GPIO signals on those pins remain available. See
the signals chapter in the device reference manual for the signal muxing.
A
1
2
3
4
5
VSS
VDD
VSTBY
AN37
AN11
B VDD33
VSS
6
7
VDDA1 VSSA1
8
9
10
11
12
13
14
15
16
17
18
19
20
21
AN1
AN5
VRH
VRL
AN27
AN28
AN35
VSSA0
AN12
MDO11 MDO10 MDO8
VDD
VDD33
AN0
AN4
REF
BYPC
AN23
AN26
AN31
AN32
VSSA0
AN13
MDO9
MDO7
MDO4
MDO0
VSS
VDDA0
22
VSS
A
VDD
AN36
AN39
AN19
AN16
VSS
VDD
AN8
AN17
AN20
AN21
AN3
AN7
AN22
AN25
AN30
AN33
AN14
MDO5
MDO2
MDO1
VSS
VDDE7
VDD
C
VSS
VDD
AN38
AN9
AN10
AN18
AN2
AN6
AN24
AN29
AN34 VDDEH AN15
9
MDO6
MDO3
C
ETPUA ETPUA
30
31
D
ETPUA ETPUA ETPUA
28
29
26
VDDE7 B
VSS
VDDE7
TCK
TDI
D
ETPUA ETPUA ETPUA ETPUA
E
24
27
25
21
VDDE7
TMS
TDO
TEST
E
ETPUA ETPUA ETPUA ETPUA
F
23
22
17
18
VDDE7 JCOMP
EVTI
EVTO F
ETPUA ETPUA ETPUA ETPUA
G
20
19
14
13
RDY
MCKO MSEO0 MSEO1 G
VDDEH GPIO
10
203
ETPUA ETPUA ETPUA VDDEH
H
16
15
10
1
GPIO
204
SINB
H
ETPUA ETPUA ETPUA ETPUA
J
6
9
12
11
VSS
VSS
VSS
VSS
VSS
VDDE7
SOUTB PCSB3 PCSB0 PCSB1 J
ETPUA ETPUA ETPUA ETPUA
K
5
8
7
2
VSS
VSS
VSS
VSS
VSS
VSS
PCSA3 PCSB4 SCKB PCSB2 K
ETPUA ETPUA ETPUA ETPUA
L
1
4
3
0
VSS
VSS
VSS
VSS
VSS
VSS
PCSB5 SOUTA
M
TCRCLK
BDIP
A
N
CS3
P
ADDR
16
R
ADDR
18
CS2
CS1
WE1
WE0
ADDR
RD_WR VDD33
17
ADDR VDDE2
19
TA
ADDR
T
20
ADDR
21
ADDR
12
TS
ADDR
U
22
ADDR
23
ADDR
13
ADDR
14
ADDR
V
24
ADDR
25
ADDR
15
ADDR
31
ADDR
ADDR
W
VDDE2
30
26
ADDR
Y
28
ADDR
AA
29
AB
VDDE2 VDDE2
CS0
ADDR
27
VSS
VSS
VSS
VSS
VSS
VSS
PCSA1 PCSA0 PCSA2
VSS
VDDE2
VSS
VSS
VSS
PCSA4 TXDA PCSA5 VFLASH N
VSS
VSS
VDDE2
VSS
VSS
VSS
CNTXC RXDA RSTOUT
RXDB
NC
No connect. Reserved (W18 & Y19 are shorted to each other)
VDDE2 VDD33 VDDE2
DATA
11
DATA
12
DATA
14
EMIOS EMIOS VDDEH EMIOS EMIOS VDDE5
21
4
12
2
8
DATA
13
DATA
15
EMIOS EMIOS EMIOS EMIOS EMIOS CNTXA VDDE5
22
17
10
15
6
DATA
8
DATA
9
DATA
10
GPIO
207
DATA
5
DATA
7
VDD
VDDE2
VDD
VDDE2
DATA
1
VDDE2
GPIO
206
DATA
2
DATA
3
DATA
4
DATA
6
OE
5
6
7
8
9
VSS
VSS
VDD
VDDE2
DATA
0
1
2
3
4
NC
VPP
RST
CFG
M
P
CNRXC TXDB RESET R
BOOT
CFG1
VRC
VSS
VSS
SYN
T
VDDEH PLL
6
CFG1
BOOT
CFG0
EXTAL U
VRC
CTL
PLL
CFG0
XTAL
V
VDD
SYN
W
VDD
VDD
SCKA L
VSS
WKP
CFG
Note:
SINA
VSS
VDD
VRC33
NC
VSS
VDD
VDD33 Y
VDDE2 EMIOS EMIOS EMIOS EMIOS EMIOS EMIOS EMIOS CNRXA VDDE5 CLKOUT VSS
23
19
16
3
5
9
13
VDD
AA
EMIOS EMIOS EMIOS EMIOS EMIOS EMIOS EMIOS EMIOS CNTXB CNRXB VDDE5
20
18
14
0
1
4
7
11
ENG
CLK
VSS
AB
21
22
10
11
12
13
14
15
16
17
18
19
20
Figure 25. MPC5533 324 Package
MPC5533 Microcontroller Data Sheet, Rev. 0.0
44
Freescale Semiconductor
Mechanicals
4.3
MPC5533 208-Pin Package Dimensions
The package drawings of the MPC5533 208-pin MAP BGA are shown in Figure 26.
Figure 26. MPC5533 208-Pin Package
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
45
Mechanicals
Figure 26. MPC5533 208 MAP BGA Package (continued)
MPC5533 Microcontroller Data Sheet, Rev. 0.0
46
Freescale Semiconductor
Mechanicals
4.4
MPC5533 324-Pin Package Dimensions
The package drawings of the MPC5533 324-pin TEPBGA package are shown in Figure 27.
Figure 27. MPC5533 324 TEPBGA Package
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
47
Mechanicals
Figure 27. MPC5533 324 TEPBGA Package (continued)
MPC5533 Microcontroller Data Sheet, Rev. 0.0
48
Freescale Semiconductor
Revision History for the MPC5533 Data Sheet
5
Revision History for the MPC5533 Data Sheet
Table 27 provides a revision history of the MPC5533 Data Sheet.
Table 27. Revision History for the MPC5533 Data Sheet
Substantive Change(s)
Initial version for MPC5533.
Version
Rev. 0.0
MPC5533 Microcontroller Data Sheet, Rev. 0.0
Freescale Semiconductor
49
How to Reach Us:
Home Page:
www.freescale.com
E-mail:
[email protected]
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
+1-800-521-6274 or +1-480-768-2130
[email protected]
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
[email protected]
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
[email protected]
Document Number: MPC5533
Rev. 0.0
10 Oct 2008
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do vary
in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc. 2008. All rights reserved.
RoHS-compliant and/or Pb-free versions of Freescale products have the functionality
and electrical characteristics as their non-RoHS-compliant and/or non-Pb-free
counterparts. For further information, see http://www.freescale.com or contact your
Freescale sales representative.
For information on Freescale’s Environmental Products program, go to
http://www.freescale.com/epp.