Document 641-1 Shielded Power Inductors – MSS6132 • 6.1 × 6.1 mm footprint; 3.2 mm high shielded inductors • Low DCR and excellent current handling Designer’s Kit C364 contains 3 of each value Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Terminations RoHS compliant matte tin over nickel over phos bronze (current production) or gold over nickel over phos bronze (prior production). Other terminations available at additional cost. Weight 0.33 – 0.38 g Ambient temperature –40°C to +85°C with (40°C rise) Irms current. Maximum part temperature +125°C (ambient + temp rise). Derating. Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 500/7″ reel, 1500/13″ reel; Plastic tape: 16 mm wide, 0.3 mm thick, 12 mm pocket spacing, 3.1 mm pocket depth PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Inductance2 Part number1 ±20% (µH) MSS6132-472ML_ 4.7 MSS6132-562ML_ 5.6 MSS6132-682ML_ 6.8 MSS6132-822ML_ 8.2 MSS6132-103ML_ 10 MSS6132-123ML_ 12 MSS6132-153ML_ 15 MSS6132-183ML_ 18 MSS6132-223ML_ 22 MSS6132-273ML_ 27 MSS6132-333ML_ 33 MSS6132-393ML_ 39 MSS6132-473ML_ 47 MSS6132-563ML_ 56 MSS6132-683ML_ 68 MSS6132-823ML_ 82 MSS6132-104ML_ 100 DCR SRF max typ3 (Ohms) (MHz) 0.043 65.0 0.048 60.0 0.052 47.0 0.055 45.0 0.070 39.0 0.079 33.0 0.106 27.0 0.118 24.0 0.158 21.0 0.180 19.0 0.250 18.0 0.275 17.0 0.300 16.0 0.380 14.0 0.410 12.0 0.510 10.0 0.660 9.0 Isat (A)4 Irms (A)5 10% 20% 30% 20°C 40°C drop drop drop rise rise 2.18 2.60 2.84 2.30 3.10 2.10 2.50 2.74 2.20 2.95 1.80 2.12 2.30 2.10 2.80 1.78 2.06 2.22 2.00 2.65 1.36 1.64 1.84 1.90 2.50 1.30 1.54 1.70 1.75 2.35 1.16 1.42 1.56 1.65 2.20 1.04 1.22 1.36 1.55 2.05 0.97 1.12 1.22 1.45 1.90 0.91 1.08 1.18 1.30 1.75 0.81 0.96 1.10 1.20 1.60 0.79 0.92 0.99 1.10 1.45 0.72 0.86 0.93 0.95 1.30 0.61 0.72 0.79 0.85 1.15 0.55 0.63 0.69 0.73 1.00 0.53 0.62 0.67 0.60 0.85 0.45 0.54 0.59 0.50 0.69 1. Please specify termination and packaging codes: MSS6132-823MLC Termination: L = RoHS compliant matte tin over nickel over phos bronze (current production) or gold over nickel over phos bronze (prior production) Special order: T = RoHS tin-silver-copper (95.5/4/0.5) over gold over nickel over phos bronze or S = non-RoHS tin-lead (63/37) over gold over nickel over phos bronze. Packaging: C= 7″ machine-ready reel EIA-481 embossed plastic tape (500 per full reel). B= Less than full reel In tape, but not machine-ready. To have a leader and trailer added ($25 charge), use code letter C instead. D= 13″ machine-ready reel EIA-481 embossed plastic tape. Factory order only, not stocked (1500 per reel per full reel). 2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc using an Agilent/HP 4263B LCR meter or equivalent. 3. SRF measured using Agilent/HP 4191A or equilvalent. 4. DC current at which the inductance drops the specified amount from its value without current. 5. DC current at 25°C that causes the specified inductance drop from its value without current. Click for temperature derating information. 6. Current that causes the specified temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. Click for temperature derating information. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Document 641-1 Revised 09/02/15 Document 641-2 SMT Power Inductors – MSS6132 Typical L vs Current Typical L vs Frequency 1000 100 µH 100 Inductance (µH) Inductance (µH) 1000 22 µH 10 4.7 µH 1 0.01 1 0.1 10 Current (A) 0.240* 6,1 123 100 µH 100 22 µH 10 1 4.7 µH 0.01 0.1 1 10 Frequency (MHz) 0.237 6,0 min 0.079 2,0 0.240* 6,1 0.237 6,0 0.191 ∅ 4,85 Dash number Recommended Land Pattern 0.112 ±0.014 2,85 ±0,35 0.079 2,0 0.220 5,6 0.220 5,6 Dimensions are in * Dimensions are of the case not including the termination. For maximum overall dimensions including the termination, add 0.016 in / 0,4 mm. inches mm Document 641-2 Revised 09/02/15