Product Specification 2.125 Gb/s RoHS Compliant Short-Wavelength SFP Transceiver FTLF8519P3ByL PRODUCT FEATURES Up to 2.125 Gb/s bi-directional data links Hot-pluggable SFP footprint Built-in digital diagnostic functions 850nm Oxide VCSEL laser transmitter Duplex LC connector RoHS Compliant and Lead-Free Up to 500m on 50/125μm MMF, 300m on 62.5/125μm MMF APPLICATIONS Metal enclosure, for lower EMI 1.25 Gb/s 1000Base-SX Ethernet Single 3.3V power supply <500mW power dissipation Dual Rate 1.063/2.125 Gb/s Fibre Channel Industrial operating temperature range: -40°C to 85°C Wireless – CPRI, OBSAI, LTE Finisar’s FTLF8519P3xyL Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA)1. They are simultaneously compatible with Gigabit Ethernet as specified in IEEE Std 802.32 and Fibre Channel FC- PI-2 Rev. 5.03. They are RoHS compliant and lead-free per Directive 2002/95/EC4 and Finisar Application Note AN-2038. Digital diagnostics functions are available via the 2-wire serial bus specified in the SFP MSA. PRODUCT SELECTION FTLF8519P3xyL y N T Extended Temperature, -20 to 85oC Industrial Temperature, -40 to 85oC © Finisar Corporation Jan 19, 2011 Rev. B.4 Page 1 FTLF8519P3xyL Pluggable SFP Product Specification – October 2009 I. Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Pin Descriptions Symbol VEET TFAULT TDIS MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) Rate Select LOS VEER VEER VEER RDRD+ VEER VCCR VCCT VEET TD+ TDVEET Name/Description Transmitter Ground (Common with Receiver Ground) Transmitter Fault. Transmitter Disable. Laser output disabled on high or open. Module Definition 2. Data line for Serial ID. Module Definition 1. Clock line for Serial ID. Module Definition 0. Grounded within the module. No connection required Loss of Signal indication. Logic 0 indicates normal operation. Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Inverted DATA out. AC Coupled Receiver Non-inverted DATA out. AC Coupled Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Non-Inverted DATA in. AC Coupled. Transmitter Inverted DATA in. AC Coupled. Transmitter Ground (Common with Receiver Ground) Ref. 1 2 3 3 3 4 1 1 1 1 1 1 Notes: 1. Circuit ground is internally isolated from chassis ground. 2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. 3. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 3.6V. MOD_DEF(0) pulls line low to indicate module is plugged in. 4. LOS is open collector output. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. Towards Bezel 1 VeeT 2 TXFault 3 TX Disable 4 MOD-DEF(2) 5 MOD-DEF(1) 6 MOD-DEF(0) 7 Rate Select 8 LOS 9 VeeR 10 VeeR VeeT 20 TD- 19 TD+ 18 VeeT 17 VccT 16 VccR 15 VeeR 14 RD+ 13 RD- 12 VeeR 11 Towards ASIC Diagram of Host Board Connector Block Pin Numbers and Names © Finisar Corporation Jan 19, 2011 Rev. B.4 Page 2 FTLF8519P3ByL Pluggable SFP Product Specification – January 2011 II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Commercial Temperature Extended Temperature Industrial Temperature Relative Humidity III. Symbol Vcc TS TA RH Min -0.5 -40 -40 -5 -5 -40 0 Typ Max 4.0 85 85 70 85 85 85 Unit V °C °C Max 3.46 144 Unit V mA Ref. 1200 Vcc Vee+ 0.8 Ω mV V V 2 3 4 550 175 175 mV ps ps 5 6 6 VccHOST Vee+0.5 V V mVpp ps ps 7 7 8 9 10 % Ref. 1 Electrical Characteristics (TA, VCC = 3.15 to 3.46 Volts) Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage Receiver Single ended data output swing Data output rise time Data output fall time Mask Margin LOS Fault LOS Normal Power Supply Rejection Deterministic Jitter Contribution Total Jitter Contribution Symbol Vcc Icc Rin Vin,pp VD VEN Min 3.15 Typ 120 100 250 2 Vee Vout,pp tr tf 250 VLOS fault VLOS norm PSR RX Δ DJ RX Δ TJ 2 Vee 100 450 90 90 45% <65 51.7 122.4 Notes: 1. Non condensing. 2. Connected directly to TX data input pins. AC coupling from pins into laser driver IC. 3. We recommend <600mV for best EMI performance. 4. Or open circuit. 5. Into 100 ohms differential termination. 6. 20 – 80 % 7. LOS is an open collector output. Should be pulled up with 4.7k – 10kohms on the host board. Normal operation is logic 0; loss of signal is logic 1. Maximum pull-up voltage is 5.5V. 8. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network. 9. Typical peak-to-peak jitter (=6*RMS width of Jitter). 10. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and Δ DJ. 11. If measured with TJ-free data input signal. In actual application, output TJ will be given by: TJ OUT = DJ IN + ΔDJ + (TJ IN − DJ IN )2 + (ΔTJ − ΔDJ )2 © Finisar Corporation Jan 19, 2011 Rev. B.4 Page 3 FTLF8519P3ByL Pluggable SFP Product Specification – January 2011 IV. Optical Characteristics (TA, VCC = 3. 15 to 3.46 Volts) Parameter Transmitter Output Opt. Pwr: 50 or 62.5 MMF Optical Wavelength Spectral Width Optical Modulation Amplitude @ 2.125 Gb/s Optical Modulation Amplitude @ 1.0625 Gb/s Optical Rise/Fall Time Relative Intensity Noise Deterministic Jitter Contribution Total Jitter Contribution Extinction Ratio @ 1.25 Gb/s Mask Margin Receiver Receiver Sensitivity = 1.0625 Gb/s Receiver Sensitivity = 2.125 Gb/s Receiver Sensitivity = 1.25 Gb/s Stressed RX sens. =1.0625 Gb/s Stressed RX sens. =2.125 Gb/s Stressed RX sens. =1.25 Gb/s Average Receiver Power Receiver Elec. 3 dB cutoff freq. Optical Center Wavelength Optical Return Loss LOS De-Assert LOS Assert LOS Hysteresis Symbol Min POUT λ σ OMA -9 830 OMA tr/ tf RIN TX Δ DJ TX Δ TJ ER Typ Max Unit Ref. -2.5 860 0.85 1 196 dBm nm nm μW 2 156 μW 2 150 -120 56.5 119 ps dB/Hz ps ps dB 3 -18 -17 -18 dBm dBm dBm mW mW dBm dBm MHz nm dB dBm dBm dB 100 20 <65 9 4 5 45% RxSENS RxSENS RxSENS 0.058 0.100 RxMAX λC LOSD LOSA 770 12 -13.5 0 1500 860 -20 -30 0.5 6 6 7 8 8 9 Notes: 1. Class 1 Laser Safety per FDA/CDRH, IEC, and EN60825-1 laser safety standards. 2. Equivalent extinction ratio specification for Fibre Channel. Allows smaller ER at higher average power. 3. Unfiltered, 20-80%. Complies with FC 1x and 2x eye mask when filtered. 4. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and Δ DJ. 5. If measured with TJ-free data input signal. In actual application, output TJ will be given by: TJ OUT = DJ IN + ΔDJ + 6. 7. 8. 9. (TJ IN − DJ IN )2 + (ΔTJ − ΔDJ )2 Specifications are for 50 micro-meter or 62.5 micro-meter fiber As measured with 9dB extinction ratio. Measured with conformance signals defined in FC-PI-4 Rev. 6.1 specifications. Measured with conformance signals defined in IEEE 802.3 specifications. © Finisar Corporation Jan 19, 2011 Rev. B.4 Page 4 FTLF8519P3ByL Pluggable SFP Product Specification – January 2011 V. General Specifications Parameter Data Rate Bit Error Rate Fiber Length on 50/125μm MMF Fiber Length on 62.5/125μm MMF Symbol BR Min Typ 1.062, 1.25, 2.125 Max 10-12 550 300 300 150 BER L L Units Gb/sec m m Ref. 1 4 2 3 2 3 Notes: 1. Gigabit Ethernet and 1x, 2x Fibre Channel compatible, per IEEE 802.3 and FC-PI-2 Rev. 5.0 respectively. 2. At 1.0625 Gb/s Fibre Channel and 1.25 Gb/s Gigabit Ethernet data rates. 3. At 2.125 Gb/s Fibre Channel data rate. 4. 2.125Gb/s with PRBS 27-1. VI. Environmental Specifications Parameter Case Operating Temperature Commercial Temperature Extended Temperature Industrial Temperature Storage Temperature VII. Symbol Top Tsto Min -40 -5 -20 -40 -40 Typ Max 85 70 85 85 85 Units °C Ref. °C Regulatory Compliance Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TÜV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request. Copies of the referenced certificates are available at Finisar Corporation upon request. © Finisar Corporation Jan 19, 2011 Rev. B.4 Page 5 FTLF8519P3ByL Pluggable SFP Product Specification – January 2011 VIII. Digital Diagnostic Functions Finisar FTLF8519P3xyL SFP transceivers support the 2-wire serial communication protocol as defined in the SFP MSA1. It is very closely related to the E2PROM defined in the GBIC standard, with the same electrical specifications. The standard SFP serial ID provides access to identification information that describes the transceiver’s capabilities, standard interfaces, manufacturer, and other information. Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range. The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged. The interface is identical to, and is thus fully backward compatible with both the GBIC Specification and the SFP Multi Source Agreement. The complete interface is described in Finisar Application Note AN2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. For more information, please see the SFP MSA documentation1,5 or Finisar Application Note AN-2030. Please note that evaluation board FDB-1018 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface. © Finisar Corporation Jan 19, 2011 Rev. B.4 Page 6 FTLF8519P3ByL Pluggable SFP Product Specification – January 2011 IX. Digital Diagnostic Specifications FTLF8519P2xyL transceivers can be used in host systems that require either internally or externally calibrated digital diagnostics. Parameter Symbol Accuracy DDTemperature Internally measured transceiver temperature DDVoltage Internally measured transceiver supply voltage DDBias Measured TX bias current DDTx-Power Measured TX output power DDRx-Power Measured RX received average optical power Dynamic Range for Rated Accuracy DDTemperature Internally measured transceiver temperature DDVoltage Internally measured transceiver supply voltage DDBias Measured TX bias current DDTx-Power Measured TX output power DDRx-Power Measured RX received average optical power Max Reporting Range DDTemperature Internally measured transceiver temperature DDVoltage Internally measured transceiver supply voltage DDBias Measured TX bias current DDTx-Power Measured TX output power DDRx-Power Measured RX received average optical power Min Typ Max Units 3 ºC 100 mV 10 2 2 % dB dB -40 85 ºC 3.0 3.6 V 0 -9 -20 20 -2.5 0 mA dBm dBm -40 125 ºC 2.8 4.0 V 0 -10 -22 20 -2 0 mA dBm dBm Ref. 1 Notes: 1. Accuracy of Measured Tx Bias Current is 10% of the actual Bias Current from the laser driver to the laser. © Finisar Corporation Jan 19, 2011 Rev. B.4 Page 7 FTLF8519P3ByL Pluggable SFP Product Specification – January 2011 X. Mechanical Specifications Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA). FTLF8519P3ByL © Finisar Corporation Jan 19, 2011 Rev. B.4 Page 8 FTLF8519P3ByL Pluggable SFP Product Specification – January 2011 XI. PCB Layout and Bezel Recommendations © Finisar Corporation Jan 19, 2011 Rev. B.4 Page 9 FTLF8519P3ByL Pluggable SFP Product Specification – January 2011 © Finisar Corporation Jan 19, 2011 Rev. B.4 Page 10 FTLF8519P3ByL Pluggable SFP Product Specification – January 2011 XII. References 1. Small Form Factor Pluggable (SFP) Transceiver Multi-source Agreement (MSA). September 14, 2000. 2. IEEE Std 802.3, 2002 Edition, Clause 38, PMD Type 1000BASE-SX. IEEE Standards Department, 2002. 3. “Fibre Channel Draft Physical Interface Specification (FC-PI-2 Rev. 5.0)”. American National Standard for Information Systems. 4. Directive 2002/95/EC of the European Council Parliament and of the Council, “on the restriction of the use of certain hazardous substances in electrical and electronic equipment.” January 27, 2003. 5. “Digital Diagnostics Monitoring Interface for Optical Transceivers”. SFF Document Number SFF-8472, Revision 9.3. XIII. For More Information Finisar Corporation 1308 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 [email protected] www.finisar.com © Finisar Corporation Jan 19, 2011 Rev. B.4 Page 11