Kemet C1206C56312RAC Surface mount ceramic chip capacitors extended values 1206, x7r dielectric, 25, 50, 100, 200 volt Datasheet

New Product Release
Surface Mount Ceramic Chip Capacitors
Extended Values 1206, X7R Dielectric, 25, 50, 100, 200 Volts
25 Volts – 1.2µF - 1.5 µF
50 Volts – 0.27µF - 0.68µF
100 Volts – 0.27µF - 0.39µF
200 Volts – 27,000pF - 150,000pF
Outline Drawings
Table 1 - Dimensions - Millimeters
EIA
Metric Size
Size Code Code (Ref)
1206*
3216
L#
Length
W#
Width
Thickness
B
Bandwidth
S
Min. Separation
Mounting
Technique
3.2 (.126) ± 0.2 (.008)
1.6 (.063) ± 0.2 (.008)
See Table 2
0.5 (.02) ± .25 (.010)
N/A
Solder Wave or
Solder Reflow
Table 2 - Ratings & Part Number Listing
Cap Values
KEMET Part Number
Capacitance Tolerance Thickness - mm Qty 7” Reel Qty 13” Reel
1.2µF
C1206C125(1)3RAC
J,K,M
1.60 ± 0.15
2,000
1.5µF
C1206C155(1)3RAC
J,K,M
1.60 ± 0.15
2,000
8,000
0.27µF
C1206C274(1)5RAC*
J,K,M
.90 ± .10
4,000
10,000
0.33µF
C1206C334(1)5RAC*
J,K,M
.90 ± .10
4,000
10,000
0.39µF
C1206C394(1)5RAC*
J,K,M
.90 ± .10
4,000
10,000
0.47µF
C1206C474(1)5RAC*
J,K,M
.90 ± .10
4,000
10,000
0.56µF
C1206C564(1)5RAC*
J,K,M
.90 ± .10
4,000
10,000
0.68µF
C1206C684(1)5RAC*
J,K,M
1.00 ± 0.10
2,500
10,000
0.27µF
C1206C274(1)1RAC
J,K,M
1.25 ± 0.15
2,500
10,000
0.33µF
C1206C334(1)1RAC
J,K,M
1.60 ± 0.15
2,000
8,000
0.39µF
C1206C394(1)1RAC
J,K,M
1.60 ± 0.15
2,000
8,000
27,000pF
C1206C273(1)2RAC
J,K,M
.78 ± .10
2,500
10,000
33,000pF
C1206C333(1)2RAC
J,K,M
.78 ± .10
2,500
10,000
39,000pF
C1206C393(1)2RAC
J,K,M
.78 ± .10
2,500
10,000
47,000pF
C1206C473(1)2RAC
J,K,M
1.00 ± 0.10
2,500
10,000
56,000pF
C1206C563(1)2RAC
J,K,M
1.00 ± 0.10
2,500
10,000
68,000pF
C1206C683(1)2RAC
J,K,M
1.00 ± 0.10
2,500
10,000
82,000pF
C1206C823(1)2RAC
J,K,M
1.00 ± 0.10
2,500
10,000
100,000pF
C1206C104(1)2RAC
J,K,M
1.25 ± 0.15
2,500
10,000
120,000pF
C1206C124(1)2RAC
J,K,M
1.25 ± 0.15
2,500
10,000
150,000pF
C1206C154(1)2RAC
J,K,M
1.60 ± 0.15
2,000
8,000
To complete the KEMET part number, insert capacitance tolerance: J - ±5%, K - ±10% or M ±20%.
* X7R Dielectric - Extended Range Values - Cap and DF measured at 0.5 Vrms.
F3274A 04/05
8,000
Electrical Parameters
As detailed in the KEMET Surface Mount Catalog F3102 for X7R, with following specific requirements based on
room temperature (25°C) parameters:
• Operating Range: -55°C to +125°C, with no-bias capacitance shift limited to ± 15% over that range
• Insulation Resistance (IR) measured after 2 minutes at rated voltage @ 25°C: Limit is 1000
megohm microfarads or 100 gigohms, whichever is less.
• Capacitance and Dissipation Factor (DF) measured at 1KHz at 1.0Vrms.
25 Volts - DF Limit is 3.5%
> 25 Volts - DF Limit is 2.5%
Soldering Process
Wave soldering or reflow soldering is acceptable for these chips.
Marking
These chips are normally supplied unmarked. If required, they can be laser marked as an extra cost option.
In general, the information in the KEMET Surface Mount catalog F3102 applies to these capacitors. The information in
this bulletin supplements that in the catalog.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • (864) 963-6682 • www.kemet.com
Similar pages