MTP300 Series SEMICONDUCTOR RoHS RoHS Nell High Power Products Three-Phase Bridge Rectifier, 300A MTP30008 Thru MTP30018 51.00 4-ø6.50 ~ 67.0 52.50 ~ 33.50 ~ - + 51.00 94.00 108.00 42.0 3-M6 Screw 7.5 32.5 2-M8 Screw FEATURES UL recognition file number E320098 Typical IR less than 5.0 µA High surge current capability Low thermal resistance Compliant to RoHS Isolation voltage up to 2500V TYPICAL APPLICATIONS DC power supplies for apparatus device Input rectifying power supplies for PWM converters Field supplies for DC motors PRIMARY CHARACTERRISTICS Inverter welders ADVANTAGE International standard package Epoxy meets UL 94 V-O flammability rating Small volume, light weight Weight: 600g (21.2 ozs) www.nellsemi.com Page 1 of 3 IF(AV) 300A V RRM 800V to 1800V I FSM 4000A IR 20 µA VF 1.30V T J max. 150ºC MTP300 Series SEMICONDUCTOR RoHS RoHS Nell High Power Products MAJOR RATINGS AND CHARACTERISTICS (TA = 25°C unless otherwise noted) MTP300 PARAMETER UNIT SYMBOL 08 10 12 16 18 Maximum repetitive peak reverse voltage V RRM 800 1000 1200 1600 1800 V Peak reverse non-repetitive voltage V RSM 900 1100 1300 1700 1900 V Maximum DC blocking voltage V DC 800 1000 1200 1600 1800 V Maximum average forward rectified output current at T C = 100°C I F(AV) 300 A I FSM 4000 A Rating (non-repetitive, for t greater than 1 ms and less than 8.3 ms) for fusing I 2t 66.4 KA 2 s RMS isolation voltage from case to leads V ISO 2500 V TJ -40 to 150 ºC T STG -40 to 125 ºC Peak forward surge current single sine-wave superimposed on rated load Operating junction storage temperature range Storage temperature range ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted) TEST CONDITIONS SYMBOL Maximum instantaneous forward drop per diode I F = 300A VF Maximum reverse DC current at rated DC blocking T A = 25°C voltage per diod T A = 150°C PARAMETER MTP300 08 10 IR 12 UNIT 16 18 1.30 V 20 µA 10 mA THERMAL AND MECHANICAC (TA = 25°C unless otherwise noted) MTP300 TEST CONDITIONS PARAMETER UNIT SYMBOL 08 Typical thermal resistance junction to case Mounting torque ± 10 % to heatsink M6 to terminal M8 Single-side heat dissipation, sine half wave R θJC (1) 12 0.08 A mounting compound is recommended and the torque should be rechecked after a period of 3 hours to allow for the spread of the compound. °C/W Nm Notes (1) With heatsink, single side heat dissipation, half sine wave. MTP 300 16 1 2 3 - Module type: ”MTP” for 3Ø Brıdge 2 - I F(AV) rating:"300" for 300 A 3 - Voltage code:code x 100 = VRRM 1 18 10 600 Device code 16 4 Approximate weight www.nellsemi.com 10 Page 2 of 3 g MTP300 Series SEMICONDUCTOR RoHS RoHS Nell High Power Products Fig.1 Forward current vs. Forward voltage Fig.2 Thermal lmpedance (junction to case) 0.08 2.5 Transient Thermal Impedance (°C/W) Peak on-state voltage (V) 3 TJ=25°C 2.0 1.5 1.0 0.5 0.06 0.04 0.02 0 0 10 1000 100 0.001 0.01 Peak on-state current (A) 10 1 Time (s) Fig.3 Power Consumption vs. Avergage Current Fig.4 Case Temperature vs. O-state Average Current 1200 400 1050 On-state average current(A) On-state Power consumption (W) 0.1 900 750 600 450 300 300 200 100 150 0 0 0 100 200 300 400 0 On-state average current (A) 30 60 90 120 150 180 Case Temperature (°C) Fig.6 I2t characteristic Fig.5 Forward Surge Current vs. Cycle 80 4000 3000 60 50 2 I t (KA S) 2000 40 2 Forward surge current (A) 70 1000 30 20 10 0 0 1 10 100 1 Time (ms) Cycle @ 50Hz www.nellsemi.com 5 Page 3 of 3 10