7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER A NON-CRIMP HEIGHT ADJUST 2150390 -7 A FINE CRIMP HEIGHT ADJUST 3.30 mm [.130] WIRE STRIP LENGTH n 4.80-5.60 mm [.189-.220 IN] NONE - TERMINALS APPLIED TE TERMINAL 880688-1 WIRE SIZE 1.00mm2 0.5+0.35mm 0.50mm2 1 2 B 880688-2 C1__DWG_PN_1_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 - 2119951-1 SMART APPLICATOR 1901697-1 2161326-1 - - - PNEUMATIC FEED 2063961-1 2119950-1 - 8- 2150390 -4 - - - 8- 2150390 -5 - - - - 2119792-2 - - - - - - - - - - - 2119641-1 - - - - - 2168400-7 - (QUANTITY 2) - - - 2063440-2 - - - - - - - 6 - - - C1__DWG_PN_2_0 - TE TERMINAL TE TERMINAL C1__DWG_PN_3_0 C1__DWG_PN_4_0 6 C1__DWG_PN_2_1 CRIMP HEIGHT REFERENCE SETTING 1.63+/-0.05 [.064+/-.002] 1.60+/-0.05 [.063+/-.002] 1.33+/-0.05 [.052+/-.002] 5.3 W1__DWG_CRIMP_HT_1 5.6 W1__DWG_CRIMP_HT_2 8.7 W1__DWG_CRIMP_HT_3 6 9 W1__FA_SETTING_1 W1__FA_SETTING_2 W1__FA_SETTING_3 6 *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. RECOMMENDED SPARE PARTS GREASE BEARING SURFACES LIGHTLY APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8SERVO FEED WITH "NON-CRIMP HEIGHT ADJUST": 8- 2150390 -4 2150390 -5 2150390 -6 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 7 8 9 APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 50, 62 FOR -6 ONLY APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 37, 50 GREASE THREADS, GROOVE AND O-RING ON ITEMS 35 & 242. & 242. 1 & 252. MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 10 TERMINAL PITCH NOT COMPATIBLE WITH MECHANICAL FEED.. 11 WHEN ASSEMBLING -6 NON-CRIMP HEIGHT ADJUST APPLICATOR USE SHIM PACK 2119957-2 TO ALIGN APPLICATOR'S MAXIMUM WIRE CRIMP HEIGHT AT NORMAL TERMINATOR SHUT HEIGHT 1 1 1 - 1 - 1 - 1 - 1 1 1 1 -77 -7 -6 -5 -2 A 1 1 1 1 1 2119957-2 8-21084-0 2119640-1 2079988-1 2119641-1 APPLICATOR SHIM PACK O-RING, .676 ID, .070 DIA. MAT. PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI FEED CAM, AIR FEED PART NO DESCRIPTION 260 252 250 249 248 1 1 ITEM NO Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 - 1 - 1 1 - 1 - 1 1 - - 1 - - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - - 2 2 - - - - 1 - - 1 1 - - REF REF - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - - - - 2 - 1 1 1 1 - REF REF REF REF - - - - 1 - - - - 1 - - REF REF - - 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 2 2 2 2 - 1 1 1 1 - 1 - - 1 - 2 2 2 2 - 1 1 1 1 - 1 - 1 1 - 3 - 3 3 - 1 1 1 1 - 4 4 4 4 - 2 2 2 2 - 2 2 2 2 - 2 2 2 2 - 2 2 2 2 - 1 1 1 1 - - - - 1 - 1 1 1 1 - - - - 1 - 1 1 1 1 - 1 - 1 1 - 1 1 1 1 - 1 - 1 1 - 1 - 1 1 - 1 1 1 1 - 1 1 1 1 - 1 - 1 1 - 8 8 8 8 - 2 2 2 2 - 2 2 2 2 - 1 1 1 1 - 2 2 2 2 - 1 1 1 1 - 2 2 2 2 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 4 4 4 4 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - - - - - 1 1 1 1 1 1 1 1 1 - 1 1 1 1 - - - - - 1 1 1 1 - 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 P LTR 2119798-1 1-22279-3 2119759-1 2119082-7 2079764-1 2119083-1 2168400-7 2063440-2 2119740-2 1901697-1 6-993111-6 8-22280-7 1752353-2 1901680-2 21045-3 994969-1 994970-2 240638-1 3-23627-7 SEE NOTE 4 1633743-1 455888-4 2119791-9 2119956-2 2-18032-2 2119943-1 2119740-1 2168078-1 1901681-1 2119793-1 992763-5 2079383-4 2168400-4 2168083-9 5018030-2 5018030-1 986965-8 1-5018030-0 2119792-2 1752354-5 18023-9 2119655-5 2119369-1 2079383-7 2119645-1 2119957-1 1-2119644-2 2119085-1 2119092-1 1-18028-2 2168083-9 1-2168083-0 240639-1 1320906-1 1752371-5 2-22281-3 1752373-4 1-1901695-8 1-1901696-8 1-2079383-1 455888-3 1752360-1 240644-9 6-690482-3 3-1803001-5 1-2217206-0 7-240641-6 238009-1 2-1633961-6 455888-5 1-456405-3 1 1 1 1 1 1 2 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 2 1 1 2 1 1 3 1 4 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 8 2 2 1 2 1 2 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 -77 -7 -6 -5 -2 PART NO THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: ATLANTIC VERSION AMP 4805 REV 31MAR2000 66 DESCRIPTION DATE RELEASED DWN APVD BH 18DEC2013 GB - 1.40-2.70 mm [.055-.106 IN] 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 2063961-1 INSULATION DIAMETER RANGE CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 SERVO LATCH PLATE SERVO 11 LATCH PLATE NONE - 10 TE TERMINAL C1__DWG_PN_1_0 4 A REVISIONS DIST PART NUMBERS REQUIRED - 4 LOC 1 A TE CRIMP SPECIFICATION FASTIN-FASTON .250 TAB TERMINAL APPLICATION SPECIFICATION SERVO LATCH PLATE CRIMP TOOLING KIT TE TERMINAL TERMINAL NAME: SET UP GAUGE 2119599-2 F F 2.03 mm [.080] TERMINAL DATA: 2 TYPE APPL INSTRUCTIONS 408-10390 C A CONVERT TO PNEUMATIC FINE CRIMP HEIGHT ADJUST 2150390 -6 SIZE 3 APPLICATOR STYLE CONVERSION CHART FEED TYPE FINE CRIMP HEIGHT ADJUST A 7- 2150390 -7 WIRE INSUL DESCRIPTION A 2150390 -5 CRIMP 4 20 REVISION 2150390 -2 APPLICATOR DATA 5 ALL RIGHTS RESERVED. PART NUMBER D 6 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 18DEC2013 CHK 18DEC2013 APVD 18DEC2013 K.STAKEM G.BAILEY M.CLIFFORD TE Connectivity Harrisburg, PA 17105-3608 NAME - APPLICATION SPEC - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 ITEM NO DESCRIPTION PRODUCT SPEC - 247 246 245 244 243 242 240 238 213 183 177 176 175 174 172 166 164 163 137 135 133 82 73 71 70 69 67 66 65 63 62 60 57 56 55 54 53 52 51 50 49 46 44 41 40 39 38 37 35 33 31 29 27 25 24 22 20 19 18 17 14 13 11 10 9 8 7 6 5 4 3 2 1 DETENT PIN SPRING, COMPRESSION RAM, AMP STYLE, END FEED, NON-ADJUST CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SHCS, LOW HEAD, RoHS, M5 X 10 AIR FEED MODULE TAG,IDENTIFICATION FEED FINGER ASSEMBLY,EF PIN, SLOTTED SPRING 3.0 X 14.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM SPACER, CRIMPER DEPRESSOR, WIRE DOCUMENTATION PACKAGE SCR, SET, FLT POINT M3 X 10.0 WASHER, SPACER TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 HOLDDOWN, TERMINAL LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, BHSC, RoHS (M4 X 8) SHCS, LOW HEAD, RoHS, M4 X 8 SCR, SKT HD CAP, RoHS, M4 X 20 NUT, HEX, REG, RoHS, M4 NUT, HEX, REG, RoHS, M3 NUT, LOCK, HEX, TORQUE (M4) NUT, HEX, REG, RoHS, M3.5 PAWL, EF, AIR STANDOFF,HOLD-DOWN SCR, SKT HD CAP M4 X 6.0 APPLICATOR BASIC ASSEMBLY, EF RAM,AMP STYLE, END FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION FA HEAD, ATLANTIC STYLE BOLT, ADJUSTMENT WASHER, FLAT, REG M4 SCR, SKT HD CAP, RoHS, M4 X 20 SCR, SKT HD CAP, RoHS, M4 X 10 STRIPPER (MACHINING) STUD, THREADED PLATE, STRIP GUIDE SPRING, COMPRESSION DRAG STRIP GUIDE, FRONT STRIP GUIDE, REAR SCR, BHSC, RoHS (M6 X 12) SPACER, CRIMPER SPACER,HOLD-DOWN PLATE, REAR SHEAR PLATE, FRONT SHEAR ANVIL, COMBINATION, END FEED BLADE, SLUG SPACER BLOCK, FL CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM Ocean End Feed Applicator - DRAWING NO 2150390 SCALE 1:1 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV A D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR - HOLD DOWN 6 DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - 37 40 62 6 38 D D 39 19.65 [ 0.774 ] 247 260 246 252 7 245 35 7 44 243 6 2 2 2 1 2 56 7 FEED TYPE 2 244 5 166 242 177 63 82 1 8 1 PNEUMATIC 14 69 C 73 238 2 3 C 176 2 1 4 41 70 175 2 2 249 2 54 174 250 A 137 55 52 163 65 172 10 50 164 A 6 20 2 18 51 57 33 SERVO LATCH PLATE 67 213 B 19 66 B CAM POSITION 30mm STROKE 29 33 27 8 1 46 60 31 13 9 1 11 1 17 53 33 25 22 24 248 4 49 A 135 133 183 240 REF A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 40mm STROKE AIR FEED AMP 4805 REV 31MAR2000 SERVO FEEDER NOT INCLUDED A DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 18DEC2013 CHK 18DEC2013 APVD 18DEC2013 K.STAKEM G.BAILEY M.CLIFFORD TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean End Feed Applicator - DRAWING NO 2150390 SCALE 1:1 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 6 5 4 3 2 20 SET UP GAUGE 2119599-2 ALL RIGHTS RESERVED. PART NUMBER REVISION 2- 2150390 -2 DESCRIPTION A 2- 2150390 -5 2- 2150390 -7 SERVO LATCH PLATE FINE CRIMP HEIGHT ADJUST A CONVERT TO - PNEUMATIC FINE CRIMP HEIGHT ADJUST A 7- 2150390 -7 FEED TYPE FINE CRIMP HEIGHT ADJUST A APPLICATOR STYLE CONVERSION CHART NONE CRIMP TOOLING KIT - SERVO LATCH PLATE SMART APPLICATOR 4 - PNEUMATIC FEED - CRIMP WIRE INSUL SIZE - 2063961-1 2119951-1 1901697-1 2161326-1 - - 2063961-1 2119950-1 8- 2150390 -5 8- 2150390 -4 2119792-2 - - - - - - - - 2119653-2 - 2119653-2 2119641-2 - - - APPL INSTRUCTIONS 408-10390 TE TERMINAL TERMINAL DATA: - 2168400-7 - (QUANTITY 2) - - - 6 2063440-2 - - - - WIRE STRIP LENGTH n 4.80-5.60 mm [.189-.220 IN] C TERMINAL APPLICATION SPECIFICATION NONE - TERMINALS APPLIED TE TERMINAL 880688-1 TE CRIMP SPECIFICATION FASTIN-FASTON .250 TAB TERMINAL NAME: 880688-2 C1__DWG_PN_1_1 1.40-2.70 mm [.055-.106 IN] - - - 10 TE TERMINAL C1__DWG_PN_1_0 INSULATION DIAMETER RANGE - C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_3_0 TE TERMINAL C1__DWG_PN_4_0 C1__DWG_PN_2_1 6 WIRE SIZE 1.00mm2 0.5+0.35mm 0.50mm2 B CRIMP HEIGHT REFERENCE SETTING CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.63+/-0.05 [.064+/-.002] 1.60+/-0.05 [.063+/-.002] 1.33+/-0.05 [.052+/-.002] 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 5.3 5.6 8.7 9 W1__FA_SETTING_1 W1__FA_SETTING_2 W1__FA_SETTING_3 6 *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8- 2150390 -4 2150390 -5 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 50, 62 7 GREASE THREADS, GROOVE AND O-RING ON ITEMS 139 8 9 10 1 & 242. 1 & 153. 1 MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. TERMINAL PITCH NOT COMPATIBLE WITH MECHANICAL FEED. 1 - 1 1 1 1 1 1 1 1 -77 -27 -25 -22 A 1 1 1 1 2119782-1 2119640-1 2079988-1 1-22279-3 PART NO FINE ADJUST HEAD ASM, PACIFIC STYLE PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI SPRING, COMPRESSION DESCRIPTION 251 250 249 246 1 1 ITEM NO Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 - 1 1 1 - 1 1 1 - 1 1 1 - - 2 - - - 1 - - 1 - 4 4 4 - - REF - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - - - 2 - 1 1 1 - REF REF REF - - - 1 - 1 1 1 - - - 1 - 1 1 1 - 1 1 1 - - - - 1 1 1 - 1 1 1 - 1 1 1 - - - 1 - - REF - - 1 - 1 1 1 - 1 1 1 - 1 1 1 - 2 2 2 - 1 1 1 - 1 - 1 - 2 2 2 - 1 1 1 - 1 1 1 - 3 3 3 - 4 4 4 - 2 2 2 - 2 2 2 - 2 2 2 - 2 2 2 - 1 1 1 - - - 1 - 1 1 1 - - - 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 8 8 8 - 2 2 2 - 2 2 2 - 1 1 1 - 2 2 2 - 1 1 1 - 2 2 2 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - - - - 1 1 1 1 1 1 1 - 1 1 1 - - - - 1 1 1 - 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 LTR 2119082-7 2079764-1 2119083-1 2168400-7 2063440-2 2119740-2 2079383-9 1901697-1 6-993111-6 8-22280-7 1752353-2 1901680-2 21045-3 994969-1 994970-2 240638-1 8-21084-1 2119641-2 2119798-2 2079383-8 2119653-2 2119655-6 2119651-1 2119092-2 3-23627-7 SEE NOTE 4 1633743-1 455888-4 2119791-9 2119956-2 2-18032-2 2119943-1 2119740-1 2168078-1 1901681-1 2119793-1 992763-5 2168400-4 2168083-9 5018030-2 5018030-1 986965-8 1-5018030-0 2119792-2 1752354-5 18023-9 2079383-7 2119645-1 2119957-1 1-2119644-2 1-18028-2 2168083-9 1-2168083-0 240639-1 1320906-1 1752371-5 2-22281-3 1752373-4 1-1901695-8 1-1901696-8 455888-3 1752360-1 240644-9 6-690482-3 3-1803001-5 1-2217206-0 7-240641-6 238009-1 2-1633961-6 455888-5 1-456405-3 1 1 1 2 1 1 4 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 1 1 3 4 2 2 2 2 1 1 1 2 1 1 1 1 8 2 2 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -77 -27 -25 -22 PART NO THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION AMP 4805 REV 31MAR2000 P DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - - F F 3.30 mm [.130] 66 PART NUMBERS REQUIRED TYPE 2.03 mm [.080] A REVISIONS DIST - D APPLICATOR DATA LOC 1 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 18DEC2013 CHK 18DEC2013 APVD 18DEC2013 K.STAKEM G.BAILEY M.CLIFFORD TE Connectivity Harrisburg, PA 17105-3608 NAME - APPLICATION SPEC - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 ITEM NO DESCRIPTION PRODUCT SPEC - 244 243 242 240 238 213 186 183 177 176 175 174 172 166 164 163 153 152 145 144 142 141 140 139 137 135 133 82 73 71 70 69 67 66 65 63 62 57 56 55 54 53 52 51 50 49 41 40 39 38 33 31 29 27 25 24 22 20 19 18 14 13 11 10 9 8 7 6 5 4 3 2 1 CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SHCS, LOW HEAD, RoHS, M5 X 10 AIR FEED MODULE TAG,IDENTIFICATION SCR, BHSC, RoHS (M6 X 20) FEED FINGER ASSEMBLY,EF PIN, SLOTTED SPRING 3.0 X 14.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER O-RING, .801 ID, .070 DIA. MAT. FEED CAM, AIR FEED DETENT PIN SCR, BHSC, RoHS (M4 X 16) FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, EF RAM, ASIAN STYLE, END FEED BOLT, ADJUSTMENT PIN, RETAIN, GRVD, 3/16 X .854 MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM SPACER, CRIMPER DEPRESSOR, WIRE DOCUMENTATION PACKAGE SCR, SET, FLT POINT M3 X 10.0 WASHER, SPACER TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 HOLDDOWN, TERMINAL LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SHCS, LOW HEAD, RoHS, M4 X 8 SCR, SKT HD CAP, RoHS, M4 X 20 NUT, HEX, REG, RoHS, M4 NUT, HEX, REG, RoHS, M3 NUT, LOCK, HEX, TORQUE (M4) NUT, HEX, REG, RoHS, M3.5 PAWL, EF, AIR STANDOFF,HOLD-DOWN SCR, SKT HD CAP M4 X 6.0 SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION WASHER, FLAT, REG M4 SCR, SKT HD CAP, RoHS, M4 X 20 SCR, SKT HD CAP, RoHS, M4 X 10 STRIPPER (MACHINING) STUD, THREADED PLATE, STRIP GUIDE SPRING, COMPRESSION DRAG STRIP GUIDE, FRONT STRIP GUIDE, REAR SPACER, CRIMPER SPACER,HOLD-DOWN PLATE, REAR SHEAR PLATE, FRONT SHEAR ANVIL, COMBINATION, END FEED BLADE, SLUG SPACER BLOCK, FL CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM Ocean End Feed Applicator - DRAWING NO 2150390 SCALE 1:1 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - 251 HOLD DOWN 40 6 62 38 39 D 19.65 [ 0.774 ] 7 7 D 145 153 246 139 140 244 243 6 2 166 242 8 2 56 2 2 1 FEED TYPE 7 5 177 63 82 1 PNEUMATIC 1 14 69 C 73 238 2 3 C 2 1 4 2 41 2 249 176 2 70 175 250 A 54 174 137 55 163 52 172 65 6 20 10 A 50 2 51 57 18 33 164 SERVO LATCH PLATE 67 19 213 B 66 B CAM POSITION 30mm STROKE 152 SERVO FEEDER NOT INCLUDED A 29 33 27 8 1 141144 31 13 9 1 11 1 186 53 33 25 22 24 4 133 135 183 240 REF A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 PACIFIC VERSION AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 18DEC2013 CHK 18DEC2013 APVD 18DEC2013 K.STAKEM G.BAILEY M.CLIFFORD TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean End Feed Applicator - DRAWING NO 2150390 SCALE 1:1 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A