NPN Silicon Photodarlington OP300SL Series Features: • • • • • Narrow receiving angle Variety of sensitivity ranges Enhanced temperature range PCBoard mounting Mechanically and spectrally matched to OP123 and OP223 LEDs Description: Each device in this series is a NPN silicon photodarlington in a hermetically sealed pill package with a narrow receiving angle that provides excellent on-axis coupling. Photodarlingtons are normally used in applications with low light signal levels, where more current gain is needed than phototransistors can provide. Components in the OP300 series are mechanically and spectrally matched to the OP123 and OP223 series. Please refer to Application Bulletins 208 and 210 for additional design information and reliability (degradation) data, and to Application Bulletin 202 for pill-type soldering to PCBoard. Applications: • • • Ordering Information Non-contact reflective object sensor Assembly line automation Machine automation 1 • • • Machine safety End of travel sensor Door sensor Part Number OP300SL OP301SL OP302SL OP303SL OP304SL OP305SL Sensor Darlington Light Current Input Power IC(ON) (mA) Viewing EE (mW/cm2) Min / Max Angle 0.8 / NA 1.0 with 0.8 / 2.4 2870°K 1.8 / 5.4 or 35° 3.6 / 12.0 0.4 with 7.0 / 21.0 890nm 14.0 / NA 2 Pin # Sensor 1 Collector 2 Emitter DIMENSIONS ARE IN: RoHS [MILLIMETERS] INCHES OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A 05/07 Page 1 of 4 NPN Silicon Photodarlington OP300SL Series Absolute Maximum Ratings (TA=25°C unless otherwise noted) Collector-Emitter Voltage 15.0 V Emitter-Collector Voltage 5.0 V Storage Temperature Range -65° C to +150° C Operating Temperature Range -65° C to +125° C 260° C(1)(2) Soldering Temperature (5 seconds with soldering iron) 50 mW(3) Power Dissipation Continuous Collector Current 50 mA Electrical Characteristics (TA = 25° C unless otherwise noted) SYMBOL IC(ON)(4) ICEO PARAMETER On-State Collector Current OP300SL OP301SL OP302SL OP303SL OP304SL OP305SL Collector-Dark Current MIN TYP MAX UNITS TEST CONDITIONS 0.8 0.8 1.8 3.6 7.0 14.0 - 2.4 5.4 12.0 21.0 - mA VCE = 5.0 V, EE = 1.0 or 0.4 mW/cm2(5) - - 1.0 µA VCE = 10 V, EE = 0 V(BR)CEO Collector-Emitter Breakdown Voltage 15.0 - - V IC = 100 μA V(BR)ECO Emitter-Collector Breakdown Voltage 5.0 - - V IE = 100 μA VCE(SAT)(4) Collector-Emitter Saturation Voltage OP300SL, OP301SL OP302SL through OP305SL - - 1.1 1.1 V IC = 0.4 mA, EE = 1.0 or 0.4 mW/cm2(5) IC = 1.0 mA, EE = 1.0 or 0.4 mW/cm2(5) Notes: (1) (2) (3) (4) (5) Refer to Application Bulleting 202, which discusses proper techniques for soldering pill-type devices to PCBoards. No clean or low solids. RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. Derate linearly 0.5 mW/° C above 25° C. Junction temperature maintained at 25° C. Light source is an unfiltered tungsten bulb operating at CT = 2870° K at EE =1.0 mW/cm2 or 890nm at EE =0.4 mW/cm2 . OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A 05/07 Page 2 of 4 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com NPN Silicon Photodarlington OP300SL Series Typical Spectral-Response Coupling Characteristics of OP123 & OP300SL 100% 1.0 90% 80% 890 nm 0.8 70% 0.7 Ralative Output Current Relative Response - % 0.9 935 nm 850 nm TEST CONDITIONS: VCE = 5 Volts TA = 25 °C 60% 50% 40% 30% 0.6 0.5 0.4 0.3 20% 0.2 10% 0.1 0% 0.0 600 700 800 900 1000 1100 0.0 0.2 0.4 Wavelength - nm Dark Current vs Temperature 1,000.00 0.6 0.8 1.0 Diatance (inches) Collector Current vs Temperature 10 TEST CONDITIONS: VCE = 10 Volts EE = 0 IC - Typical Collector Current (mA) ICEO - Collector Current (µA) 100.00 10.00 1.00 0.10 1 TEST CONDITIONS: λ - 890 nm VCE = 5 Volts Pulse Width = 100 μS Duty Cycle = 0.1% Measured 25 μS into pulse 0.01 0.00 0.1 0 20 40 60 80 Ambient Temperature (°C) 100 120 -60 -40 -20 0 20 40 60 80 100 120 Ambient Temperature (°C) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A 05/07 Page 3 of 4 NPN Silicon Photodarlington OP300SL Series Rise & Fall Time vs. Load Resistance Radient Intensity vs. Angular Displacement 1.0 8 TEST CONDITIONS: λ - 890 nm VCE = 5 Volts Distance to Lens = 6" [152 mm] 0.9 7 0.8 5 0.6 TR & TF (mS) Normalized radiant Intensity 6 0.7 0.5 0.4 Rise Time Fall time 4 3 0.3 2 0.2 TEST CONDITIONS: λ - 890 nm VCC = 5 Volts VRL = 1 Volt 1 0.1 0 0.0 -40 -30 -20 -10 0 10 20 30 40 0.0 2.0 Θ - Angular Displacement - Deg. 4.0 6.0 Load Resistance (K-W) 8.0 10.0 Switching time Circuit Vcc Vcc IF Vout R = LED RRLOAD = 1K Ohms The light source is a pulsed LED with a rise time of less than 500 nS. The LED output is adjusted for IC = 0.8 mA. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A 05/07 Page 4 of 4 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com