Series AM40W-NZ 40 Watt | DC-DC Converter Picture coming soon FEATURES: • • • • Super wide 6:1 Input range Extremely High Input range up to 1200VDC High Input to Output Isolation of 4000VDC Over current and Over Voltage protection • • • • No minimum load required High efficiency of up to 84% Under Voltage Input protection Reversed connection protection Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (A) Isolation (VDC) Max Capacitive Load(uF) Efficiency (200VDC) (%) AM40W-60012S-NZ AM40W-60015S-NZ AM40W-60024S-NZ 200-1200 200-1200 200-1200 12 15 24 3.33 2.67 1.67 4000 4000 4000 1200 1000 680 83 84 84 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Conditions Typical Voltage range Input Current Inrush current <2ms External fuse Input Under voltage lockout 200VDC 600VDC 1200VDC 600VDC Slow blow Maximum Units 200-1200 320 100 55 VDC 60 3.15 175-185 mA A A VDC Isolation Specifications Parameters Tested I/O voltage Conditions Typical 1 min 4000 Maximum Units VDC Output Specifications Parameters Voltage accuracy Line voltage regulation Load voltage regulation Over voltage protection Over current protection Short Circuit protection Short circuit restart Temperature coefficient Ripple & Noise Hold up time Conditions Typical ±1 ±0.5 ±0.5 Zener diode clamp LL-HL 0-100% load Continuous Auto recovery ±0.02 100 5 20MHz Bandwidth 600VDC Maximum Units ±2 ±1 ±1 % % of Vin % 110 % of Iout 200 %/ C mV p-p ms Maximum Units 95 KHz °C °C °C 95 % RH o General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum case temperature Cooling Humidity Case material Weight www.aimtec.com F 051e R13 Conditions Typical 100% load Derating above 50°C 65 -25 to 70 -25 to 85 Natural convection Black plastic (UL94-V0) 210 Tel: +1 514 620 2722 1 of 3 g Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM40W-NZ 40 Watt | DC-DC Converter General Specifications (continued) Parameters Conditions Dimensions (L x W x H) MTBF Maximum soldering temperature Typical Maximum 3.50 x 2.50 x 0.98 inches 89.00 x 63.50 x 25.00 mm o >300,000 hrs (MIL-HDBK -217F, Ground Benign, t=+25 C) 1.5mm from case for 5-10 sec 260 Units o C Safety Specifications Parameters EMI - Conducted and radiated emission Electrostatic Discharge Immunity RF, Electromagnetic Field Immunity Electrical Fast Transient/Burst Immunity Surge Immunity RF, Conducted Disturbance Immunity Power frequency Magnetic Field Immunity Voltage dips, Short Interruptions Immunity Standards EN55022, class A (with the recommended EMC circuit) EN55024: 2010 IEC 61000-4-2: Contact ±6KV/Air ±8KV, Criteria B IEC 61000-4-3: 10V/m, Criteria A IEC 61000-4-4: ±4KV, Criteria B IEC 61000-4-5: ±2KV, Criteria B IEC 61000-4-6: 10Vrms, Criteria A IEC 61000-4-8: 10A/m, Criteria A IEC 61000-4-11: 0-70%, Criteria B Pin Out Specifications Pin 1 2 3 4 5 Single +Vin -Vin +Vout -Vout N.C. 3.81 (0.15) Dimensions 3.81 (0.15) 89.00 (3.50) 3 Top View 4 27.94 (1.10) 55.88 (2.20) 63.50 (2.50) 27.94 (1.10) 2 5 3.81 (0.15) 3.81 (0.15) 1 1.30 (0.05) www.aimtec.com F 051e R13 81.30 (3.20) DIV: 10.00 (0.40) 3.85 (0.15) 5Ø 1.70 (Ø 0.07) Dimensions mm (inch) Case Tolerance ±0.50 (±0.02) Pin Diameter ± 0.10 (± 0.004) Side View 10.00 (0.40) 30.00 (1.18) 3.85 (0.15) Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM40W-NZ 40 Watt | DC-DC Converter Derating Free Air Convection at 25°C Free Air Convection 100 80 Output Power (%) 100 Safe Operating Area 200 – 1000VDC 60 40 20 80 Safe Operating Area 60 40 20 0 0 70 50 - 25 -20 0 20 40 60 200 100 80 1000 1200 Input Voltage VDC Ambient Temperature º C NOTE: 1. For Input Voltage between 1000-1200VDC the derating will depend on the temperature derating. 2. Sufficient air space for natural air flow around must be considered. Typical Application circuit + Vin Single Output FUSE 3.15A NTC + + Vin MOV S20K1000 DC - Vin DC C2 + Vin MOV S20K1000 NTC LCM 10mH 12 & 15 Vout 24 Vout - Vout TVS 20V 30V Single Output + + + + - Vin Model TVS - 12 & 15 Vout 220 µF / 35V 24 Vout 120 µF / 35V Recommended EMC Circuit FUSE 3.15A + C1 C2 1µF/50V - Vin Model + Vout C1 R1 C2 R2 C3 R3 C4 R4 + Vout + Vin DC DC - Vin C1, C2, C3 &C4 47 µF/450V + Vout C5 1µF/50V C6 1MΩ / 2W 220 µF / 35V 120 µF / 35V + TVS - Vout - Vout R1, R2, R3 & R4 C6 TVS 20V 30V NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R13 Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only