ACT ACTQ550/433.92/QCC8C Surface-acoustic-wave (saw) resonator Datasheet

Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: [email protected]
The ACTQ550/433.92/QCC8C is a two-port, 180° surface-acoustic-wave (SAW) resonator in a
surface-mount ceramic QCC8C case. It provides reliable, fundamental-mode, quartz frequency
stabilization i.e. in transmitters or local oscillators operating at 433.920 MHz.
1. Package Dimension (QCC8C)
2.
Pin
Configuration
2
Input / Output
6
Output / Input
4,8
Case Ground
1,3,5,7
NC
Sign
Data (unit: mm)
Sign
Data (unit: mm)
A
2.08
E
1.2
B
0.6
F
1.35
C
1.27
G
5.0
D
2.54
H
5.0
3. Equivalent LC Model and Test Circuit
4. Typical Application Circuits
1) Low-Power Transmitter Application
2) Local Oscillator Application
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
Issue : 1 C1
Date : SEPT 04
Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: [email protected]
5. Typical Frequency Response
6. Temperature Characteristics
7. Performance
7-1.Maximum Ratings
Value
Unit
CW RF Power Dissipation
Rating
P
10
dBm
DC Voltage Between Terminals
VDC
±30
V
Storage Temperature Range
Tstg
-40 to +85
°C
Operating Temperature Range
TA
-10 to +60
°C
7-2.Electronic Characteristics
Centre Frequency
(+25°C)
Characteristic
Sym
Minimum
Absolute Frequency
fC
433.845
Tolerance from 433.920 MHz
∆fC
±75
IL
6.0
Unloaded Q
QU
15,040
50 Ω Loaded Q
QL
7,500
Turnover Temperature
TO
Turnover Frequency
fO
Insertion Loss
Quality Factor
Temperature
Stability
Frequency Temperature Coefficient
Frequency Aging
Absolute Value during the First Year
25
Maximum
Unit
433.995
MHz
kHz
8.0
dB
55
°C
fc
FTC
0.032
|fA|
≤10
DC Insulation Resistance Between Any Two Terminals
RF Equivalent
RLC Model
Typical
kHz
ppm/°C
2
ppm/yr
1.0
MΩ
RM
99.5
Motional Inductance
LM
549.079
Motional Capacitance
CM
0.24526
fF
1.30
pF
Shunt Static Capacitance
CO
1.10
151
Ω
Motional Resistance
µH
1.60
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
Issue : 1 C1
Date : SEPT 04
Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: [email protected]
iCAUTION: Electrostatic Sensitive Device. Observe precautions for handling!
1.
2.
3.
4.
5.
6.
7.
8.
9.
The frequency fC is the frequency of minimum IL with the resonator in the specified test fixture in a 50 Ω test
system with VSWR≤1.2:1.
Unless noted otherwise, case temperature T C = +25°C±2°C.
Frequency aging is the change in f C with time and is specified at +65°C or less. Aging may exceed the
specification for prolonged temperatures above +65°C. Typically, aging is greatest the first year after
manufacture, decreasing in subsequent years.
Turnover temperature, T0, is the temperature of maximum (or turnover) frequency, f 0. The nominal frequency at
2
any case temperature, TC, may be calculated from: f = f 0 [1 - FTC (T 0 - TC) ].
This equivalent RLC model approximates resonator performance near the resonant frequency and is provided
for reference only. The capacitance C 0 is the measured static (non-motional) capacitance between input terminal
and ground or output terminal and ground. The measurement includes case parasitic capacitance.
Derived mathematically from one or more of the following directly measured parameters: f C, IL, 3 dB bandwidth,
fC versus TC, and C0.
The specifications of this device are based on the test circuit shown above and subject to change or
obsolescence without notice.
Typically, equipment utilizing this device requires emissions testing and government approval, which is the
responsibility of the equipment manufacturer.
Our liability is only assumed for the Surface Acoustic Wave (SAW) component(s) per se, not for applications,
processes and circuits implemented within components or assemblies.
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
Issue : 1 C1
Date : SEPT 04
Similar pages