Fairchild MOC3032M 6-pin dip zero-cross optoisolators triac driver output (250/400 volt peak) Datasheet

MOC3031M, MOC3032M, MOC3033M,
MOC3041M, MOC3042M, MOC3043M
6-Pin DIP Zero-Cross Optoisolators Triac Driver Output
(250/400 Volt Peak)
Features
Description
■ Simplifies logic control of 115 VAC power
The MOC303XM and MOC304XM devices consist of a
GaAs infrared emitting diode optically coupled to a
monolithic silicon detector performing the function of a
zero voltage crossing bilateral triac driver.
■ Zero voltage crossing
■ dv/dt of 2000 V/µs typical, 1000 V/µs guaranteed
■ VDE recognized (File # 94766), ordering option V
(e.g., MOC3043VM)
Applications
■ Solenoid/valve controls
■ Lighting controls
They are designed for use with a triac in the interface of
logic systems to equipment powered from 115 VAC
lines, such as teletypewriters, CRTs, solid-state relays,
industrial controls, printers, motors, solenoids and
consumer appliances, etc.
■ Static power switches
■ AC motor drives
■ Temperature controls
■ E.M. contactors
■ AC motor starters
■ Solid state relays
Schematic
Package Outlines
ANODE 1
6 MAIN TERM.
CATHODE 2
N/C 3
5 NC*
ZERO
CROSSING
CIRCUIT
4 MAIN TERM.
*DO NOT CONNECT
(TRIAC SUBSTRATE)
©2005 Fairchild Semiconductor Corporation
MOC303XM, MOC304XM Rev. 1.0.7
www.fairchildsemi.com
MOC303XM, MOC304XM — 6-Pin DIP Zero-Cross Optoisolators Triac Driver Output (250/400 Volt Peak)
September 2010
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability.
The absolute maximum ratings are stress ratings only.
Symbol
Parameters
Device
Value
Units
TOTAL DEVICE
TSTG
Storage Temperature
All
-40 to +150
°C
TOPR
Operating Temperature
All
-40 to +85
°C
TSOL
Lead Solder Temperature
All
260 for 10
sec
°C
Junction Temperature Range
All
-40 to +100
°C
Isolation
(peak AC voltage, 60Hz, 1 sec. duration, II-O ≤ 2µA)
All
7500
Vac(pk)
Total Device Power Dissipation @ 25°C
All
250
mW
2.94
mW/°C
TJ
VISO
PD
Surge Voltage(1)
Derate above 25°C
EMITTER
IF
Continuous Forward Current
All
60
mA
VR
Reverse Voltage
All
6
V
PD
Total Power Dissipation 25°C Ambient
All
120
mW
1.41
mW/°C
MOC3031M/2M/3M
250
V
MOC3041M/2M/3M
400
Peak Repetitive Surge Current
(PW = 100µs, 120 pps)
All
1
A
Total Power Dissipation @ 25°C Ambient
All
150
mW
All
1.76
mW/°C
Derate above 25°C
DETECTOR
VDRM
ITSM
PD
Off-State Output Terminal Voltage
Derate above 25°C
Note
1. Isolation surge voltage, VISO, is an internal device dielectric breakdown rating. For this test, Pins 1 and 2 are
common, and Pins 4, 5 and 6 are common.
©2005 Fairchild Semiconductor Corporation
MOC303XM, MOC304XM Rev. 1.0.7
2
www.fairchildsemi.com
MOC303XM, MOC304XM — 6-Pin DIP Zero-Cross Optoisolators Triac Driver Output (250/400 Volt Peak)
Absolute Maximum Ratings (TA = 25°C unless otherwise noted)
Individual Component Characteristics
Symbol
Parameters
Test Conditions
Device
Min.
Typ.
Max.
Units
EMITTER
VF
Input Forward Voltage
IF = 30mA
All
1.25
1.5
V
IR
Reverse Leakage Current
VR = 6V
All
0.01
100
µA
IDRM1
Peak Blocking Current,
Either Direction
Rated VDRM, IF = 0(2)
All
100
nA
VTM
Peak On-State Voltage,
Either Direction
ITM = 100mA peak, IF = 0
All
3
V
dv/dt
Critical Rate of Rise of
Off-State Voltage
IF = 0 (Figure 9)(4)
All
DETECTOR
1.8
1000
V/µs
Transfer Characteristics
Symbol
IFT
IH
DC Characteristics
LED Trigger Current
Test Conditions
Main Terminal
Voltage = 3V(3)
Holding Current,
Either Direction
Max.
Units
MOC3031M/
MOC3041M
Device
Min.
15
mA
MOC3032M/
MOC3042M
10
MOC3033M/
MOC3043M
5
All
Typ.
400
µA
Zero Crossing Characteristics
Symbol
VIH
IDRM2
Characteristics
Test Conditions
Device
Min.
Typ.
Max.
Units
Inhibit Voltage
IF = rated IFT, MT1-MT2
voltage above which device
will not trigger
off-state
All
20
V
Leakage in Inhibited
State
IF = rated IFT, rated VDRM
off-state
All
2
mA
Notes:
2. Test voltage must be applied within dv/dt rating.
3. All devices are guaranteed to trigger at an IF value less than or equal to max IFT. Therefore, recommended
operating IF lies between max IFT (15mA for MOC3031M & MOC3041M, 10mA for MOC3032M & MOC3042M,
5mA for MOC3033M & MOC3043M) and absolute max IF (60mA).
4. This is static dv/dt. See Figure 9 for test circuit. Commutating dv/dt is a function of the load-driving thyristor(s) only.
©2005 Fairchild Semiconductor Corporation
MOC303XM, MOC304XM Rev. 1.0.7
3
www.fairchildsemi.com
MOC303XM, MOC304XM — 6-Pin DIP Zero-Cross Optoisolators Triac Driver Output (250/400 Volt Peak)
Electrical Characteristics (TA = 25°C Unless otherwise specified)
As per IEC 60747-5-2, this optocoupler is suitable for “safe electrical insulation” only within the safety limit data.
Compliance with the safety ratings shall be ensured by means of protective circuits.
Symbol
Parameter
Min.
Typ.
Max.
Unit
Installation Classifications per DIN VDE 0110/1.89
Table 1
For Rated Main Voltage < 150Vrms
I-IV
For Rated Main voltage < 300Vrms
I-IV
Climatic Classification
55/100/21
Pollution Degree (DIN VDE 0110/1.89)
2
CTI
Comparative Tracking Index
175
VPR
Input to Output Test Voltage, Method b,
VIORM x 1.875 = VPR, 100% Production Test
with tm = 1 sec, Partial Discharge < 5pC
1594
Vpeak
Input to Output Test Voltage, Method a,
VIORM x 1.5 = VPR, Type and Sample Test
with tm = 60 sec, Partial Discharge < 5pC
1275
Vpeak
VIORM
Max. Working Insulation Voltage
850
Vpeak
VIOTM
Highest Allowable Over Voltage
6000
Vpeak
External Creepage
7
mm
External Clearance
7
mm
Insulation Thickness
0.5
mm
Insulation Resistance at Ts, VIO = 500V
109
Ω
RIO
©2005 Fairchild Semiconductor Corporation
MOC303XM, MOC304XM Rev. 1.0.7
4
www.fairchildsemi.com
MOC303XM, MOC304XM — 6-Pin DIP Zero-Cross Optoisolators Triac Driver Output (250/400 Volt Peak)
Safety and Insulation Ratings
Figure 2. On-State Characteristics
800
1.5
600
IF = 30mA
ITM, ON-STATE CURRENT (mA)
VF - FORWARD VOLTAGE (V)
Figure 1. LED Forward Voltage vs. Forward Current
1.6
1.4
1.3
TA = -40°C
1.2
TA = 25°C
1.1
TA = 85°C
1.0
TA = 25°C
400
200
0
-200
-400
-600
0.9
-800
0.8
0.1
1
10
-4
100
-3
1.2
1000
1.1
1.0
0.9
NORMALIZED TO
T A = 25oC
0
20
40
60
80
1
2
3
4
100
10
1
0.1
-40
100
-20
0
20
40
60
80
100
TA, AMBIENT TEMPERATURE ( oC)
TA, AMBIENT TEMPERATURE (°C)
©2005 Fairchild Semiconductor Corporation
MOC303XM, MOC304XM Rev. 1.0.7
0
Figure 4. Leakage Current, IDRM vs. Temperature
10000
IDRM, LEAKAGE CURRENT (nA)
IFT, NORMALIZED
Figure 3. Trigger Current vs. Temperature
1.3
-20
-1
VTM, ON-STATE VOLTAGE (VOLTS)
IF - LED FORWARD CURRENT (mA)
0.8
-40
-2
5
www.fairchildsemi.com
MOC303XM, MOC304XM — 6-Pin DIP Zero-Cross Optoisolators Triac Driver Output (250/400 Volt Peak)
Typical Performance Curves
Figure 6. LED Current Required to Trigger vs. LED Pulse Width
Figure 5. IDRM2 - Leakage in Inhibit State vs. Temperature
1.8
IFT, LED TRIGGER CURRENT (NORMAILZED)
16
IDRM2, NORMALIZED
1.6
1.4
IF = RATED I FT
1.2
1.0
0.8
0.6
0.4
-40
-20
0
20
40
60
80
NORMALIZED TO
PW IN >> 100 µs
14
12
10
8
6
4
2
100
0
TA, AMBIENT TEMPERATURE (°C)
1
10
100
PWIN, LED TRIGGER PULSE WIDTH (µS)
Figure 7. Holding Current, IH vs. Temperature
Figure 8. Inhibit Voltage vs. Temperature
3.2
1.3
1.2
NORMALIZED TO
2.4
T A = 25° C
VINH - NORMALIZED
IH, HOLDING CURRENT (NORMALIZED)
2.8
2.0
1.6
1.2
1.1
1.0
0.9
0.8
0.8
0.4
0.7
0.0
-40
-40
-20
0
20
40
60
80
100
-20
0
20
40
60
80
100
TA, AMBIENT TEMPERATURE (°C)
TA, AMBIENT TEMPERATURE (°C)
©2005 Fairchild Semiconductor Corporation
MOC303XM, MOC304XM Rev. 1.0.7
6
www.fairchildsemi.com
MOC303XM, MOC304XM — 6-Pin DIP Zero-Cross Optoisolators Triac Driver Output (250/400 Volt Peak)
Typical Performance Curves (Continued)
2. 100x scope probes are used, to allow high speeds and
voltages.
+250 for MOC303XM
+400 for MOC304XM
Vdc
RTEST
3. The worst-case condition for static dv/dt is established by
triggering the D.U.T. with a normal LED input current, then
removing the current. The variable RTEST allows the dv/dt
to be gradually increased until the D.U.T. continues to
trigger in response to the applied voltage pulse, even after
the LED current has been removed. The dv/dt is then
decreased until the D.U.T. stops triggering. τRC is
measured at this point and recorded.
R = 10 kΩ
CTEST
PULSE
INPUT
MERCURY
WETTED
RELAY
X100
SCOPE
PROBE
D.U.T.
Figure 9. Static dv/dt Test Circuit
Vmax = 400 V
Vmax = 250 V
APPLIED VOLTAGE
WAVEFORM
dv/dt =
0 VOLTS
APPLIED VOLTAGE
WAVEFORM
158 V
0.63 Vmax
τRC
τ RC
=
252 V
158
dv/dt =
0 VOLTS
RC
0.63 Vmax
τRC
τ RC
=
252
τ RC
Figure 11. Static dv/dt Test Waveform
(MOC3041M, MOC3042M, MOC3043M)
Figure 10. Static dv/dt Test Waveform
(MOC3031M, MOC3032M, MOC3033M)
Typical circuit (Fig 12, 13) for use when hot line switching is required. In this circuit the “hot” side of the line is switched
and the load connected to the cold or neutral side. The load may be connected to either the neutral or hot line.
Rin is calculated so that IF is equal to the rated IFT of the part, 5mA for the MOC3033M and MOC3043M, 10mA for
the MOC3032M and MOC3042M, or 15mA for the MOC3031M and MOC3041M. The 39 ohm resistor and 0.01µF
capacitor are for snubbing of the triac and may or may not be necessary depending upon the particular triac and
load used.
Rin
1
6
Rin
180Ω
HOT
VCC
2
3
MOC3031M
MOC3032M
MOC3033M
39Ω
*
4
3
115 VAC
0.01
MOC3041M
MOC3042M
MOC3043M
360Ω
5
39Ω
*
4
330
LOAD
240 VAC
0.01
LOAD
NEUTRAL
NEUTRAL
*For highly inductive loads (power factor < 0.5), change this value to 360 ohms.
*For highly inductive loads (power factor < 0.5), change this value to 360 ohms.
Figure 13. Hot-Line Switching Application Circuit
(MOC3041M, MOC3042M, MOC3043M)
Figure 12. Hot-Line Switching Application Circuit
(MOC3031M, MOC3032M, MOC3033M)
©2005 Fairchild Semiconductor Corporation
MOC303XM, MOC304XM Rev. 1.0.7
6
HOT
2
5
1k
1
VCC
7
www.fairchildsemi.com
MOC303XM, MOC304XM — 6-Pin DIP Zero-Cross Optoisolators Triac Driver Output (250/400 Volt Peak)
1. The mercury wetted relay provides a high speed repeated
pulse to the D.U.T.
R1
1
VCC
Rin
2
D1
6
MOC3031M
MOC3032M
MOC3033M
3
SCR
5
SCR
180
4
R2
D2
LOAD
Figure 14. Inverse-Parallel SCR Driver Circuit
(MOC3031M, MOC3032M, MOC3033M)
Suggested method of firing two, back-to-back SCR’s with a Fairchild triac driver. Diodes can be 1N4001; resistors, R1
and R2, are optional 1kΩ.
240 VAC
R1
1
VCC
Rin
2
3
D1
6
MOC3041M
MOC3042M
MOC3043M
SCR
5
SCR
4
360
R2
D2
LOAD
Figure 15. Inverse-Parallel SCR Driver Circuit
(MOC3041M, MOC3042M, MOC3043M)
Suggested method of firing two, back-to-back SCR’s with a Fairchild triac driver. Diodes can be 1N4001; resistors,
R1 and R2, are optional 330Ω.
Note:
This optoisolator should not be used to drive a load directly. It is intended to be a trigger device only.
©2005 Fairchild Semiconductor Corporation
MOC303XM, MOC304XM Rev. 1.0.7
8
www.fairchildsemi.com
MOC303XM, MOC304XM — 6-Pin DIP Zero-Cross Optoisolators Triac Driver Output (250/400 Volt Peak)
115 VAC
Through Hole
0.4" Lead Spacing
8.13–8.89
6
4
8.13–8.89
6
4
1
3
6.10–6.60
6.10–6.60
Pin 1
1
3
Pin 1
5.08 (Max.)
3.28–3.53
0.25–0.36
7.62 (Typ.)
5.08 (Max.)
3.28–3.53
0.38 (Min.)
0.25–0.36
2.54–3.81
0.38 (Min.)
2.54 (Bsc)
(0.86)
0.41–0.51
2.54–3.81
0.20–0.30
15° (Typ.)
2.54 (Bsc)
(0.86)
1.02–1.78
0.41–0.51
0.76–1.14
0.20–0.30
10.16–10.80
1.02–1.78
0.76–1.14
Surface Mount
(1.78)
8.13–8.89
6
4
(1.52)
(2.54)
(7.49)
6.10–6.60
8.43–9.90
Pin 1
(10.54)
1
3
(0.76)
Rcommended Pad Layout
0.25–0.36
3.28–3.53
5.08
(Max.)
0.38 (Min.)
0.20–0.30
2.54 (Bsc)
(0.86)
0.16–0.88
(8.13)
0.41–0.51
1.02–1.78
0.76–1.14
Note:
All dimensions in mm.
©2005 Fairchild Semiconductor Corporation
MOC303XM, MOC304XM Rev. 1.0.7
9
www.fairchildsemi.com
MOC303XM, MOC304XM — 6-Pin DIP Zero-Cross Optoisolators Triac Driver Output (250/400 Volt Peak)
Package Dimensions
Option
Order Entry Identifier
(Example)
No option
MOC3031M
S
MOC3031SM
SR2
MOC3031SR2M
T
MOC3031TM
0.4" Lead Spacing
V
MOC3031VM
VDE 0884
TV
MOC3031TVM
VDE 0884, 0.4" Lead Spacing
SV
MOC3031SVM
VDE 0884, Surface Mount
SR2V
MOC3031SR2VM
Description
Standard Through Hole Device
Surface Mount Lead Bend
Surface Mount; Tape and Reel
VDE 0884, Surface Mount, Tape and Reel
Marking Information
1
3
MOC3031V
2
X YY Q
6
4
5
Definitions
1
Fairchild logo
2
Device number
3
VDE mark (Note: Only appears on parts ordered with VDE
option – See order entry table)
4
One digit year code, e.g., ‘3’
5
Two digit work week ranging from ‘01’ to ‘53’
6
Assembly package code
*Note – Parts that do not have the ‘V’ option (see definition 3 above) that are
marked with date code ‘325’ or earlier are marked in portrait format.
©2005 Fairchild Semiconductor Corporation
MOC303XM, MOC304XM Rev. 1.0.7
10
www.fairchildsemi.com
MOC303XM, MOC304XM — 6-Pin DIP Zero-Cross Optoisolators Triac Driver Output (250/400 Volt Peak)
Ordering Information
12.0 ± 0.1
4.5 ± 0.20
2.0 ± 0.05
Ø1.5 MIN
4.0 ± 0.1
0.30 ± 0.05
1.75 ± 0.10
11.5 ± 1.0
21.0 ± 0.1
9.1 ± 0.20
Ø1.5 ± 0.1/-0
10.1 ± 0.20
0.1 MAX
24.0 ± 0.3
User Direction of Feed
Reflow Profile
300
260°C
280
260
>245°C = 42 Sec
240
220
200
180
°C
Time above
183°C = 90 Sec
160
140
120
1.822°C/Sec Ramp up rate
100
80
60
40
33 Sec
20
0
0
60
120
180
270
360
Time (s)
©2005 Fairchild Semiconductor Corporation
MOC303XM, MOC304XM Rev. 1.0.7
11
www.fairchildsemi.com
MOC303XM, MOC304XM — 6-Pin DIP Zero-Cross Optoisolators Triac Driver Output (250/400 Volt Peak)
Carrier Tape Specification
AccuPower™
Auto-SPM™
Build it Now™
CorePLUS™
CorePOWER™
CROSSVOLT™
CTL™
Current Transfer Logic™
DEUXPEED®
Dual Cool™
EcoSPARK®
n
EfficientMax™
ESBC™
®
Fairchild®
Fairchild Semiconductor®
FACT Quiet Series™
FACT®
FAST®
FastvCore™
FETBench™
FlashWriter®*
FPS™
F-PFS™
FRFET®
SM
Global Power Resource
Green FPS™
Green FPS™ e-Series™
Gmax™
GTO™
IntelliMAX™
ISOPLANAR™
MegaBuck™
MICROCOUPLER™
MicroFET™
MicroPak™
MicroPak2™
MillerDrive™
MotionMax™
Motion-SPM™
OptoHiT™
OPTOLOGIC®
OPTOPLANAR®
®
PDP SPM™
Power-SPM™
PowerTrench®
PowerXS™
Programmable Active Droop™
QFET®
QS™
Quiet Series™
RapidConfigure™
™
Saving our world, 1mW/W/kW at a time™
SignalWise™
SmartMax™
SMART START™
SPM®
STEALTH™
SuperFET™
SuperSOT™-3
SuperSOT™-6
SuperSOT™-8
SupreMOS®
SyncFET™
Sync-Lock™
®
*
The Power Franchise®
TinyBoost™
TinyBuck™
TinyCalc™
TinyLogic®
TINYOPTO™
TinyPower™
TinyPWM™
TinyWire™
TriFault Detect™
TRUECURRENT™*
" SerDes™
UHC®
Ultra FRFET™
UniFET™
VCX™
VisualMax™
XS™
* Trademarks of System General Corporation, used under license by Fairchild Semiconductor.
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE
RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT
OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE
SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN,
WHICH COVERS THESE PRODUCTS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE
EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.
As used herein:
1. Life support devices or systems are devices or systems which, (a)
are intended for surgical implant into the body or (b) support or
sustain life, and (c) whose failure to perform when properly used in
accordance with instructions for use provided in the labeling, can be
reasonably expected to result in a significant injury of the user.
2. A critical component in any component of a life support, device, or
system whose failure to perform can be reasonably expected to
cause the failure of the life support device or system, or to affect its
safety or effectiveness.
ANTI-COUNTERFEITING POLICY
Fairchild Semiconductor Corporation's Anti-Counterfeiting Policy. Fairchild's Anti-Counterfeiting Policy is also stated on our external website, www.fairchildsemi.com,
under Sales Support.
Counterfeiting of semiconductor parts is a growing problem in the industry. All manufacturers of semiconductor products are experiencing counterfeiting of their
parts. Customers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, failed
applications, and increased cost of production and manufacturing delays. Fairchild is taking strong measures to protect ourselves and our customers from the
proliferation of counterfeit parts. Fairchild strongly encourages customers to purchase Fairchild parts either directly from Fairchild or from Authorized Fairchild
Distributors who are listed by country on our web page cited above. Products customers buy either from Fairchild directly or from Authorized Fairchild Distributors
are genuine parts, have full traceability, meet Fairchild's quality standards for handling and storage and provide access to Fairchild's full range of up-to-date technical
and product information. Fairchild and our Authorized Distributors will stand behind all warranties and will appropriately address any warranty issues that may arise.
Fairchild will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. Fairchild is committed to combat this global
problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet
Identification
Product Status
Advance Information
Formative / In Design
Preliminary
First Production
No Identification Needed
Full Production
Obsolete
Not In Production
Definition
Datasheet contains the design specifications for product development. Specifications may change
in any manner without notice.
Datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild
Semiconductor reserves the right to make changes at any time without notice to improve design.
Datasheet contains final specifications. Fairchild Semiconductor reserves the right to make
changes at any time without notice to improve the design.
Datasheet contains specifications on a product that is discontinued by Fairchild Semiconductor.
The datasheet is for reference information only.
Rev. I49
©2005 Fairchild Semiconductor Corporation
MOC303XM, MOC304XM Rev. 1.0.7
www.fairchildsemi.com
11
MOC303XM, MOC304XM — 6-Pin DIP Zero-Cross Optoisolators Triac Driver Output (250/400 Volt Peak)
TRADEMARKS
The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its global subsidiaries, and is not
intended to be an exhaustive list of all such trademarks.