BSM40 40W S i n g l e Ou t p ut C l as s I I Medi c al P owe r Su p p lie s series Up to 40W Output Power Universal 90-264VAC Input Single Outputs from 5VDC to 48VDC High Efficiency up to 85% 4000VAC Isolation 1U Compatible Height 2”W x 4”L x 1.244”H Model Number Output Voltage Max. O/P Amps Efficiency (230VAC) R&N p-p max. Capacitive Load SINGLE OUTPUT BSM40-5-A BSM40-9-A BSM40-12-A BSM40-15-A BSM40-24-A BSM40-36-A BSM40-48-A 5VDC 9VDC 12VDC 15VDC 24VDC 36VDC 48VDC 77% typ. 80% typ. 83% typ. 83% typ. 83% typ. 83% typ. 85% typ. 300mV 250mV 250mV 250mV 240mV 360mV 400mV 23,000uF 10,200uF 4,000uF 5,500uF 1,300uF 600uF 270uF 8 4.4 3.33 2.66 1.66 1.1 0.83 WWW.ASTRODYNETDI.COM ASTRODYNE USA: 1-800-823-8082 ASTRODYNE PACIFIC: 886-2-26983458 BSM40 40W S i n g l e Ou t p ut C l as s I I Medi c al P owe r Su p p lie s INPUT SPECIFICATIONS Input Voltage Range Frequency Range Input Current (90 / 264 Vin) Inrush Current (115 / 230 Vin) Leakage Current (264V / 50Hz) GENERAL SPECIFICATIONS 90-264 VAC (100-240VAC nom.) 47-63 Hz 1A / 0.4A 30A / 60A typical * BF <100uA @ 240VAC, 50Hz OUTPUT SPECIFICATIONS Voltage and Current (Note 3) Minimum Load Turn On Delay Time Rise Time Load Regulation (20%-FL) Line Regulation (LL-HL) Preset Accuracy (FL, 115Vin) Transient Response Over-Shoot and Under-Shoot Ripple/Noise (Note 1 & 4) Over Voltage Protection Over Power Protection Short Circuit Protection Hold Up Time (115V / 60Hz) Capacitive Loading (Note 5) See Selection Chart 0 Amps <1S <30mS ± 1% max ± 1% max 1% See Page 3 <10% of O/P Voltage See Selection Chart Latching re-power 240% max.* Latching, Auto Recover * 8 mS, typ. See Selection Chart PHYSICAL SPECIFICATIONS Size (Inches / mm) Construction Weight series 2” x 4” x 1.244” / 50.8 x 101.6 x 31.6 Open Frame 5.61oz (159g) All specifications are typical at nominal input, full load, and 25°C unless otherwise noted * These are stress ratings. Exposure of the devices to any of these conditions may adversely affect long term reliability. Proper operation under conditions other than the standard operating conditions is neither warranteed nor implied. WWW.ASTRODYNETDI.COM Input-Out Isolation Insulation Resistance Efficiency (typ.) Switching Frequency Safety UL/cUL: UL-EU: CB: CE: 4000VAC ≥20MΩ; 500VDC, 1S I/P-O/P See Selection Chart 65Khz, (fixed, typical) ANSI/AAMI ES60601-1 3rd ed. CSA C22.2 No. 60601-1 3rd ed. EN60601-1 3rd ed. IEC60601-1 3rd ed. EN60601-1-2 ENVIRONMENTAL SPECIFICATIONS Operating Temp. (Note 2) Storage Temperature Relative Humidity ESD RS EFT Surge CS DIPS EMI MTBF Vibration Drop Test -10 to +70°C, See Derate -25 to +85°C * 0-95% * IEC61000-4-2 IEC61000-4-3 IEC61000-4-4 IEC61000-4-5 IEC61000-4-6 IEC61000-4-11 EN55011 B / CISPR 11 B 196,000 Hrs Mil Std 217, 25°C 2G Peak, 10-500Hz, 3 Axis, 30 min 70 cm Height NOTES 1. Make all measurements directly at the pins of the supply 2. Specified for free air convection cooling 3. 115Vin minimum required for full load start up 4. Measured by paralleling 47uF/EC and 0.1uF ceramic capacitors on the output at a 20MHz band-width 5. The power supply should start up and operate normally into these capacitive loads within specified input voltage and output current ranges over the specified operating temperature range and according to Derate. ASTRODYNE USA: 1-800-823-8082 ASTRODYNE PACIFIC: 886-2-26983458 load BBSSML4400 s esreireise s 40W n g l e OuOutput t p ut C lCas s I I IIMedi c al P owe r Su lie s 40WS iSingle lass Switching Pow erpSp upplies t Δ a Table1 2 Δ Step load Δ Step load Derating Curve Ambient ( WWW.ASTRODYNETDI.COM WWW.ASTRODYNE.COM ) ASTRODYNE USA: 1-800-823-8082 ASTRODYNE USA: 1-800-823-8082 ASTRODYNE PACIFIC: 886-2-26983458 ASTRODYNE PACIFIC: 886-2-26983458 BSM40 40W S i n g l e Ou t p ut C l as s I I Medi c al P owe r Su p p lie s series MECHANICAL DIMENSIONS 4.00in 101.6mm 3.70in 94mm .15in 3.8mm .125in 3.175mm +Vout +Vout GND GND 2.00in 1.70in 50.8mm 43.2mm ACN ACL .15in 3.8mm 1.17in 29.6mm max B .08in 2mm olerance : Input connector : Molex 5273 series or equivalent Output connector : Molex 5273 series or equivalent .06in 1.6mm 0.1mm (0.004in) BSM60-A_B Length and Width Tolerance: ± 0.1mm (0.004in) DESCRIPTION DATE Height changes 2012/05/25 SIZE SCALE DIMENSION PIERCINGBENDING ANGULAR SHEET ±0.1 ±0.15 X<8 ±0.3° ±0.5° Projection ±0.1 ±0.2 8<X<25 25<X<100 100<X<300 300<X<800 WWW.ASTRODYNETDI.COM UNIT SHEET METAL TOLERANCE (UNLESS OTHERWISE SPECIFIED) 1715 ±0.5° DRAWN ±0.15 ±0.2 ±0.25 ±0.3 ±1° CHECKED ±0.3 ±0.5 ±1.5° APPROVED mm A4 1:1 OF MATERIAL PART NO. MODEL NO. TITLE Erica ASTRODYNE USA: 1-800-823-8082 ASTRODYNE PACIFIC: 886-2-26983458 2D